Trends in arsenic levels in PM10 and PM2.5 aerosol fractions in an industrialized area

Arsenic is a toxic element that affects human health and is widely distributed in the environment. In the area of study, the main Spanish and second largest European industrial ceramic cluster, the main source of arsenic aerosol is related to the impurities in some boracic minerals used in the ceramic process. Epidemiological studies on cancer occurrence in Spain points out the study region as one with the greater risk of cancer. Concentrations of particulate matter and arsenic content in PM₁₀ and PM_2.5 were measured and characterized by ICP-MS in the area of study during the years 2005–2010. Concentrations of PM₁₀ and its arsenic content range from 27 to 46 μg/m³ and from 0.7 to 6 ng/m³ in the industrial area, respectively, and from 25 to 40 μg/m³ and from 0.7 to 2.8 ng/m³ in the urban area, respectively. Concentrations of PM_2.5 and its arsenic content range from 12 to 14 μg/m³ and from 0.5 to 1.4 ng/m³ in the urban background area, respectively. Most of the arsenic content is present in the fine fraction, with ratios of PM_2.5/PM₁₀ in the range of 0.65–0.87. PM₁₀, PM_2.5, and its arsenic content show a sharp decrease in recent years associated with the economic downturn, which severely hit the production of ceramic materials in the area under study. The sharp production decrease due to the economic crisis combined with several technological improvements in recent years such as substitution of boron, which contains As impurities as raw material, have reduced the concentrations of PM₁₀, PM_2.5, and As in air to an extent that currently meets the existing European regulations.     

Levels of metals, PCBs, PCNs and PAHs in soils of a highly industrialized chemical/petrochemical area: temporal trend

In 2005, the concentrations of various metals and organic pollutants were analyzed in soils collected in different areas of Tarragona (Catalonia, Spain), where an important chemical/petrochemical complex is located. The levels of seven elements (As, Cd, Cr, Hg, Mn, Pb and V), as well as those of polychlorinated biphenyls (PCBs), polychlorinated naphthalenes (PCNs) and polycyclic aromatic hydrocarbons (PAHs) were determined in soils, and compared with those obtained in a background study carried out in 2002. Only Cd and Pb showed significant higher concentrations in the petrochemical zone, while no significant differences were found for the remaining elements. In turn, vanadium was the only element showing a significant increase in the concentration between 2002 and 2005. With regard to the organic pollutants, no significant differences were found according to the area of sampling. However, an increase in naphthalene levels was observed during the period 2002-2005 in soils of the chemical and petrochemical areas. According to the present results, it is suggested that the levels of vanadium must be periodically monitored to assure that the important industrialization of Tarragona does not mean health risks for the population living near the complex.     

Optical and chemical properties of marine boundary-layer aerosol around Japan determined from shipboard measurements in 2002

Shipboard measurements of the optical and chemical properties of marine boundary-layer aerosol were made around Japan over the period from 28 August to 25 September 2002. Measurements were conducted aboard the Research Vessel (R/V) Shirase along cruise tracks beginning from Yokosuka, and proceeding on to Hakodate, Sakata, Sasebo, Naha, Kure, and Yokkaichi. This paper describes the results of optical measurements using an Optical Particle Counter (OPC), an Integrating Nephelometer (IN), and a Particle Soot/Absorption Photometer (PSAP), as well as chemical analyses of water-soluble aerosol particles collected by impactor and filter systems. Coulter Multisizer measurements were used for water-insoluble aerosol particles. The complex refractive index (CRI), scattering and absorption coefficients, and size distribution of aerosols were estimated from combined measurements made using OPC, IN, and PSAP. Contrasting aerosol characteristics were observed during different stages of the cruise. Discussion on these differences focuses mainly on two legs: Leg-1 from Yokosuka to Hakodate and Leg-4 from Sasebo to Naha. Backward trajectory analyses indicate that the air sampled during Leg-1 originated from the Pacific Ocean, whereas the air sampled during Leg-4 originated from the Chinese Continent via the Korean Peninsula. For the first half of Leg-1, the number concentration was low and larger particles were relatively predominant. The real and imaginary parts of the CRI were estimated to be 1.38–1.40 and close to zero, respectively. This estimation is consistent with the results of chemical analyses, which show that the sea salt is rich in aerosols sourced from remote ocean areas. In contrast, small particles were predominant during Leg-4, and the real and imaginary parts of the CRI were estimated to be 1.52–1.59 and approximately −0.002, respectively. These findings are also consistent with chemical analyses that reveal a mixture of mineral dust and sulfate aerosol likely transported from China and Korea. The Coulter Multisizer measurements conducted during Leg-4 reveal abundant water-insoluble particles with a mode radius of 1.35 μm.     

Comparison of SOC estimates and uncertainties from aerosol chemical composition and gas phase data in Atlanta

In the Southeastern US, organic carbon (OC) comprises about 30% of the PM_2.5 mass. A large fraction of OC is estimated to be of secondary origin. Long-term estimates of SOC and uncertainties are necessary in the evaluation of air quality policy effectiveness and epidemiologic studies. Four methods to estimate secondary organic carbon (SOC) and respective uncertainties are compared utilizing PM_2.5 chemical composition and gas phase data available in Atlanta from 1999 to 2007. The elemental carbon (EC) tracer and the regression methods, which rely on the use of tracer species of primary and secondary OC formation, provided intermediate estimates of SOC as 30% of OC. The other two methods, chemical mass balance (CMB) and positive matrix factorization (PMF) solve mass balance equations to estimate primary and secondary fractions based on source profiles and statistically-derived common factors, respectively. CMB had the highest estimate of SOC (46% of OC) while PMF led to the lowest (26% of OC). The comparison of SOC uncertainties, estimated based on propagation of errors, led to the regression method having the lowest uncertainty among the four methods. We compared the estimates with the water soluble fraction of the OC, which has been suggested as a surrogate of SOC when biomass burning is negligible, and found a similar trend with SOC estimates from the regression method. The regression method also showed the strongest correlation with daily SOC estimates from CMB using molecular markers. The regression method shows advantages over the other methods in the calculation of a long-term series of SOC estimates.     

Link between aerosol optical,microphysical and chemical measurements in an underground railway station in Paris

Measurements carried out in Paris Magenta railway station in April–May 2006 underlined a repeatable diurnal cycle of aerosol concentrations and optical properties. The average daytime PM₁₀ and PM_2.5 concentrations in such a confined space were approximately 5–30 times higher than those measured in Paris streets. Particles are mainly constituted of dust, with high concentrations of iron and other metals, but are also composed of black and organic carbon. Aerosol levels are linked to the rate at which rain and people pass through the station. Concentrations are also influenced by ambient air from the nearby streets through tunnel ventilation. During daytime approximately 70% of aerosol mass concentrations are governed by coarse absorbing particles with a low Angström exponent (～0.8) and a low single-scattering albedo (～0.7). The corresponding aerosol density is about 2 g cm^?3 and their complex refractive index at 355 nm is close to 1.56–0.035 i. The high absorption properties are linked to the significant proportion of iron oxides together with black carbon in braking systems. During the night, particles are mostly submicronic, thus presenting a greater Angström exponent (～2). The aerosol density is lower (1.8 g cm^?3) and their complex refractive index presents a lower imaginary part (1.58–0.013 i), associated to a stronger single-scattering albedo (～0.85–0.90), mostly influenced by the ambient air. For the first time we have assessed the emission (deposition) rates in an underground station for PM₁₀, PM_2.5 and black carbon concentrations to be 3314 ± 781(?1164 ± 160), 1186 ± 358(?401 ± 66) and 167 ± 46(?25 ± 9) μg m^?2 h^?1, respectively.     

Assessment of the aerosol water content in urban atmospheric particles by the hygroscopic growth measurements in Sapporo,Japan

Aerosol water content (AWC) of urban atmospheric particles was investigated based on the hygroscopic growth measurements for 100 and 200 nm particles using a hygroscopicity tandem differential mobility analyzer in Sapporo, Japan in July 2006. In most of the humidogram measurements, presence of less and more hygroscopic mode was evident from the different dependence on relative humidity (RH). The volume of liquid water normalized by that of dry particle (V_w(RH)/V_dry) was estimated from the HTDMA data for 100 and 200 nm particles. The RH dependence of V_w(RH)/V_dry was well represented by a fitted curve with a hygroscopicity parameter κ_eff. The κ_eff values for 200 nm particles were in general higher than those for 100 nm particles, indicating a higher hygroscopicity of 200 nm particles. Based on the κ_eff values, the volume mixing ratios of water-soluble inorganic compounds (ammonium sulfate equivalent) were estimated to be on average 31% and 45% for 100 and 200 nm particles, respectively. The diurnal variation of κ_eff, with relatively higher values in the noontime and nighttime and lower values in the morning and evening hours, was observed for both particle sizes. The V_w(RH)/V_dry values under ambient RH conditions were estimated from κ_eff to range from 0.05 to 2.32 and 0.06 to 2.43 for 100 nm and 200 nm particles, respectively. The degree of correlation between κ_eff and V_w(RH)/V_dry at ambient RH suggests a significant contribution of the variation of κ_eff to atmospheric AWC in Sapporo.     

Distribution and availability of arsenic in soils from the industrialized urban area of Beijing, China

Concentrations of arsenic (As) were determined in soils of 5 industrial sites in an urban area of Beijing, China. Fifty seven typical surface soils were sampled to determine total concentrations of metals, pH and dissolved organic carbon (DOC). One hundred and eight deep soils were submitted to a four-step, sequential extraction to assess the relative mobility and bioavailability of As in the soil profiles. Total concentrations of As in surface soils ranged from 5.7 to 2.3 x 10(1) mg kg(-1), dw with greater concentrations inside the perimeter of the chemical plant which had greater concentrations than did other plants. 75.4% of surface soil samples in the industrial area contained concentrations of As that were greater than was considered to be the background concentration of 7.8 mg kg(-1), dw for the region. The mean concentration (9.9 mg kg(-1), dw) in the industrial soils was greater than that soils from other type of land use. Concentrations of As were significantly and negatively correlated with soil pH and DOC in industrial soils. Although mean concentration of total As in the soils from all sites were less at greater depths, the entire range from 0 to 180 cm (especially 0-80 cm) contained concentrations of As that were greater than background. Sequential extractions of soil indicated that only some surface soils had relatively great amount of extractable fraction of As. Most soils had relatively great amount of residual As. This result suggests that most arsenic in Beijing industrial soils should be immobile and of limited bioavailability.     

Dry and wet deposition of water-insoluble dust and water-soluble chemical species during spring 2007 in Tsukuba,Japan

Dry and wet depositions were sampled daily in Tsukuba, Japan, in spring 2007. Temporal variations in the dry and wet deposition fluxes of dust and water-soluble chemical species were controlled largely by air mass origin, the water vapor mixing ratio, and Asian dust events. The contribution of local sources to dry deposition of dust was large when the wind speed was high. Dry deposition fluxes of water-soluble chemical species were larger in humid air masses than in dry air masses. Wet deposition fluxes of dust and water-soluble chemical species indicated that air masses that passed over dust source regions and industrial regions became mixed with the maritime air masses over the coastal site of the Asian continent and western part of the Japanese islands. The total deposition of dust was 4220 mg m^?2 month^?1, and that of water-soluble chemical species ranged from 10 to 636 mg m^?2 month^?1. Wet deposition fluxes of the total deposition flux of dust accounted for 72% and those of water-soluble chemical species was for 72–96%. In particular, the largest wet deposition occurred during a single Asian dust event on 3 April. This event accounted for 23% (950 mg m^?2 month^?1) of the monthly dust deposition flux and for 2–28% (0.43–51 mg m^?2 month^?1) of the monthly deposition flux of water-soluble chemical species. This result implies that the wet deposition flux associated with even one sporadic Asian dust event can have extensive impacts on both terrestrial and oceanic ecosystems in East Asia.     

Investigation of the time evolved spatial distribution of urban PM2.5 concentrations and aerosol composition during episodic high PM events in Yuma,AZ

An interdisciplinary field study designed to investigate the spatial and temporal variability of atmospheric aerosols during high particulate matter (PM) events along the US–Mexico border near Yuma, AZ was run during the week of March 18, 2007. The experiments were designed to quantify chemical composition and physical phenomena governing the transport of aerosols generated from episodic high PM events. The field study included two micrometeorological monitoring sites; one rural and one urban, equipped with sonic anemometers, continuous particulate concentration monitors and ambient aerosol collection equipment. In addition to the two main monitoring sites, five additional locations were equipped with optical particle counters to allow for the investigation of the spatial and temporal distribution of PM_2.5 in the urban environment. In this paper, the meteorological and turbulence parameters governing the distribution and concentration of PM_2.5 in the urban environment for two high-wind erosion events and one burning event are compared. The interaction between local atmospheric conditions and the particulate distribution is investigated. Results indicate that a single point measurement in the urban area of Yuma may not be sufficient for determining the ambient PM concentrations that the local population experiences; all three high PM events indicated PM_2.5 varied considerably with maximum urban concentrations 5–10 times greater than the measured minima. A comparison of inorganic and carbonaceous content of the aerosols for the three high PM events is presented. The comparison shows an increase in silicon during crustal dust events and an increase in elemental and organic carbon during the burn event. Additional surface chemistry analysis, using time-of-flight secondary ion mass spectrometry (ToF-SIMS), for aerosols collected at the urban and rural sites during the burn event are discussed. The surface chemistry analysis provides positive ion mass spectra of organic and inorganic species in the ambient aerosol, and can be used to determine the type of combustion process that contributed to an increase in PM concentration during the burn event.     

Size distribution and sources of aerosol in Launceston, Australia, during winter 1997

As part of a pilot study into the chemical and physical properties of Australian fine particles, a suite of aerosol samples was collected at Ti Tree Bend in Launceston, Tasmania, during June and July 1997. This period represents midwinter in the Southern Hemisphere, a period when aerosol sources in Launceston are dominated by smoke from domestic wood burning. This paper describes the results from this measurement campaign, with the aim of assessing the effect of wood smoke on the chemical and physical characteristics of ambient aerosol. A micro orifice uniform deposit impactor (MOUDI) was used to measure the size distributions of the aerosol from 0.05 to 20 microns aerodynamic diameter. Continuous measurements of fine particle mass were made using a PM2.5 tapered element oscillating microbalance (TEOM) and light scattering coefficients at 530 nm were measured with nephelometers. Mass size distributions tended to be bimodal, with the diameter of the dominant mode tending to smaller sizes with increases in total mass. Non-sea salt potassium and polycyclic aromatic hydrocarbons (PAHs) were used as chemical tracers for wood smoke. Wood smoke was found to increase absolute particle mass (enough to regularly exceed air quality standards), and to concentrate mass in a single mode below 1 micron aerodynamic diameter. The acid-base equilibrium of the aerosol was altered by the wood smoke source, with free acidity hydrogen ion, non-sea salt sulfate, and ammonium concentrations being higher and the concentration of all species, including nitrate (to differing extents), focused in the fine particle size ranges. The wood smoke source also heavily influenced the aerosol scattering efficiency, adding to a strong diurnal cycle in both mass concentration and light scattering.     

Mercury transport between sediments and the overlying water of the St. Lawrence River area of concern near Cornwall, Ontario

Contaminated sediments in the St. Lawrence River remain a difficult problem despite decreases in emissions. Here, sediment and pore water phases were analyzed for total mercury (THg) and methyl mercury (MeHg) and diffusion from the sediment to the overlying water was 17.5 ± 10.6 SE ng cm⁻² yr⁻¹ for THg and 3.8 ± 1.7 SE ng cm⁻² yr⁻¹ for MeHg. These fluxes were very small when compared to the particle-bound mercury flux accumulating in the sediment (183 ± 30 SE ng cm⁻² yr⁻¹). Studies have reported that fish from the westernmost site have higher Hg concentrations than fish collected from the other two sites of the Cornwall Area of Concern, which could not be explained by differences in the Hg flux or THg concentrations in sediments, but the highest concentrations of sediment MeHg, and the greatest proportions of MeHg to THg in both sediment and pore water were observed where fish had highest MeHg concentrations.     

Determination of sterols, estrogens and inorganic ions in waste water and size-segregated aerosol particles emitted from waste water treatment

Concentrations of steroids and inorganic ions were measured in waste water of an aerated sand trap as well as in aerosol particles emitted from this tank at the waste water treatment plant (WWTP) of Bayreuth, Germany, in January and February 2003. The investigations comprised seven sterols, two estrogens, and several inorganic ions. Since an appropriate method for the determination of sterols in waste water was not available, a new method based on solid phase extraction was developed. The concentrations of the sterols coprostanol and cholesterol amounted to 30-180 microg l(-1) in waste water and to 400-5000 pg m(-3) in aerosol particles. All other sterols were present in markedly lower concentrations. The mean concentrations of the two estrogens estrone and 17beta-estradiol were about 165 pg m(-3) in aerosol particles. The steroid concentrations in both waste water and aerosol particles varied greatly over time, however with the exception of coprostanol, no clear correlation was detected between concentrations in waste water and aerosol particles.     

Trace metal and metalloid levels in surface water of Marcal River before and after the Ajka red mud spill, Hungary

The aim of this study was to compare and assess the dissolved concentrations of trace elements (As, Zn, Hg, Cd, Cr, Ni, Pb and Cu) in surface water of Marcal River before and after the red mud spill that occurred in Ajka, western Hungary, in October 2010. The caustic sludge flooded the surrounding settlements and polluted the nearby Torna Creek, which flows through the Marcal and Raba rivers into the Danube. A total of 92 surface water samples were collected from the Marcal River in the period of 2007–2012 and analysed for dissolved trace metal(loid)s by atomic absorption spectroscopy method. After the spill, the water management authority initially focused on acid dosing of surface waters to lower pH and was effective in lowering both pH and metal(loid) concentrations. Among the dissolved trace metal(loid)s, arsenic and nickel levels were moderately higher in the Marcal River 2 years since the spill compared to that observed in the pre-disaster period. The concentrations of dissolved trace metal(loid)s did not exceed the European water quality standards and the US Environmental Protection Agency aquatic life criteria values (excluding one sample for cadmium).     

Emissions of ammonia, hydrogen sulfide, and odor before, during, and after slurry removal from a deep-pit swine finisher

It is a common practice in the midwestern United States to raise swine in buildings with under-floor slurry storage systems designed to store manure for up to one year. These so-called "deep-pit" systems are a concentrated source for the emissions of ammonia (NH3), hydrogen sulfide (H2S), and odors. As part of a larger six-state research effort (U.S. Department of Agriculture-Initiative for Future Agriculture and Food Systems Project, "Aerial Pollutant Emissions from Confined Animal Buildings"), realtime NH3 and H2S with incremental odor emission data were collected for two annual slurry removal events. For this study, two 1000-head deep-pit swine finishing facilities in central Iowa were monitored with one-year storage of slurry maintained in a 2.4 m-deep concrete pit (or holding tank) below the animal-occupied zone. Results show that the H2S emission, measured during four independent slurry removal events over two years, increased by an average of 61.9 times relative to the before-removal H2S emission levels. This increase persisted during the agitation process of the slurry that on average occurred over an 8-hr time period. At the conclusion of slurry agitation, the H2S emission decreased by an average of 10.4 times the before-removal emission level. NH3 emission during agitation increased by an average of 4.6 times the before-removal emission level and increased by an average of 1.5 times the before-removal emission level after slurry removal was completed. Odor emission increased by a factor of 3.4 times the before-removal odor emission level and decreased after the slurry-removal event by a factor of 5.6 times the before-removal emission level. The results indicate that maintaining an adequate barn ventilation rate regardless of animal comfort demand is essential to keeping gas levels inside the barn below hazardous levels.     

The seasonal changes in the concentration of polycyclic aromatic hydrocarbons in precipitation and aerosol near Lake Balaton, Hungary.

The concentration of polycyclic aromatic hydrocarbons (PAHs) in atmospheric precipitation and aerosol samples was monitored in a rural site by Lake Balaton, Hungary to examine the seasonal variation. The seasonal mean concentration of individual 3-6-ring PAHs in precipitation varied from 1 to 54 ng l-1 and from 3 to 350 ng l-1 in summer and winter, respectively. In the atmospheric aerosol samples the seasonal mean concentration of PAHs varied from 4 to 880 pg m-3, from 4 to 300 pg m-3, from 11 to 1050 pg m-3 and from 36 to 5000 pg m-3 in spring, summer, autumn and winter, respectively. Wet (412 micrograms m-2 year-1) and aerosol (190-300 micrograms m2 year-1) deposition rates were also estimated indicating that the two processes are of comparable importance in the removal of 3-6-ring PAHs from the atmosphere.     

Carbonaceous aerosol characteristics in outdoor and indoor environments of Nanchang, China, during summer 2009

A study of carbonaceous aerosol was initiated in Nanchang, a city in eastern China, for the first time. Daily and diurnal (daytime and nighttime) PM2.5 (particulate matter with aerodynamic diameter < or =2.5 microm) samples were collected at an outdoor site and in three different indoor environments (common office, special printing and copying office, and student dormitory) in a campus of Nanchang University during summer 2009 (5-20 June). Daily PM10 (particulate matter with aerodynamic diameter < or =10 microm) samples were collected only at the outdoor site, whereas PM2.5 samples were collected at both indoor and outdoor sites. Loaded PM2.5 and PM10 samples were analyzed for organic and elemental carbon (OC, EC) by thermal/optical reflectance following the Interagency Monitoring of Protected Visual Environments-Advanced (IMPROVE-A) protocol. Ambient mass concentrations of PM10 and PM2.5 in Nanchang were compared with the air quality standards in China and the United States, and revealed high air pollution levels in Nanchang. PM2.5 accounted for about 70% of PM10, but the ratio of OC and EC in PM2.5 to that in PM10 was higher than 80%, which indicated that OC and EC were mainly distributed in the fine particles. The variations of carbonaceous aerosol between daytime and nighttime indicated that OC was released and formed more rapidly in daytime than in nighttime. OC/EC ratios were used to quantify secondary organic carbon (SOC). The differences in SOC and SOC/OC between daytime and nighttime were useful in interpreting the secondary formation mechanism. The results of (1) OC and EC contributions to PM2.5 at indoor sites and the outdoor site; (2) indoor-outdoor correlation of OC and EC; (3) OC-EC correlation; and (4) relative contributions of indoor and outdoor sources to indoor carbonaceous aerosol indicated that OC indoor sources existed in indoor sites, with the highest OC emissions in I2 (the special printing and copying office), and that indoor EC originated from outdoor sources. The distributions of eight carbon fractions in emissions from the printer and copier showed obviously high OC1 (>20%) and OC2 (approximately 30%), and obviously low EC1-OP (a pyrolyzed carbon fraction) (<10%), when compared with other sources.     

Daily, weekly, and seasonal time courses of VOC concentrations in a semi-urban area near Barcelona

In order to study the daily, weekly, and seasonal patterns and possible origins of air concentrations of volatile organic compounds (VOCs), measurements were taken on a minute-by-minute basis with a PTR-MS in the vicinity of a highway in a semi-urban site near Barcelona. Four periods of the year were chosen and samples were taken under different meteorological conditions and at different phenological stages of the surrounding vegetation. None of the measured VOCs concentrations exceeded air-quality guidelines. The results showed that diurnal, weekly, and seasonal fluctuations in measured VOC concentrations depended on variations in the strength of sources, as well as on photochemical activity and meteorological conditions. There was a decrease in concentrations in most VOCs when mixing depth, photochemical destruction, and wind speed increased at midday. On the other hand, high values of some VOCs occurred at night when the strength of their sinks and the mixing layer decreased. Interestingly, in June, night emissions and concentration peaks of methanol and acetone occurred in periods with dew formation and no wind. VOCs related to anthropogenic emissions presented a weekly pattern of variation with a clear distinction being found between working days and the weekend. The seasonal variation showed higher levels in December for all VOCs, except for isoprene. The thinning of the mixing layer leading to greater concentrations of volatiles and lower wind speeds in winter could account for those higher VOC levels. Benzene and toluene originated mainly from anthropogenic emissions. The sources of acetaldehyde, methanol, and acetone appeared to be mainly biogenic and these compounds were the most abundant of all the measured VOCs. Isoprene concentration patterns suggest a predominantly anthropogenic origin in December and March and a mainly biogenic origin in June and October. All these data provide useful information on the dynamics of VOCs in an area where ozone levels in summer exceed quite often the standard protection thresholds for O₃.     

城市节假日前后碳通量特征及其与车流量关系

全球变化背景下,城市作为主要的碳源,对其碳循环的研究成为陆地生态系统碳循环的重点内容之一。以上海市奉贤区为研究对象,基于涡度相关技术,结合定点连续观测的车流量数据,分析节假日（元旦）前后CO2浓度和碳通量的变化特征,及其与车流量的关系。结果表明,CO2浓度和通量日变化呈现明显的双峰型曲线,节假日CO2浓度（385.6mg/L）平均值低于工作日（401.1 mg/L）。在本研究时段内该系统表现为碳源,尽管在白天的某些时段是碳汇,表明城市系统碳通量受自然和人为2个因素共同作用,自然因素比如该系统中的香樟、雪松等常绿植物的光合作用,人为因素由人类活动造成。基于车流量与交通流量的线性回归分析表明,机动车量碳排放对于碳通量变化产生18%的贡献。     

Evaluation of non-methane hydrocarbon (NMHC) emissions based on an ambient air measurement in Tokyo area,Japan

Non-methane hydrocarbons (NMHCs) are known to have an important role on air quality due to their high reactivity. NMHC analysis has been performed on 148 ambient air samples collected at five different sites in the Kanto area (Tokyo metropolitan area and surrounding six prefectures) of Japan in summer and winter of 2008, and fifty NMHCs have been determined and quantified. A field measurement campaign has been conducted at one of the busiest intersections in Tokyo metropolitan area in winter of 2008. NMHC emissions are evaluated through comparison of distributions of individual NMHCs emitted from motor vehicles, which are estimated from the measurements, with those determined from the current emissions inventory. The comparison revealed that the measured distributions of acetylene, ethylene and toluene showed a good agreement with those estimated from the emissions inventory (the values estimated from the measurements are a factor of 1.5, 0.56 and 2.3 larger than the emissions inventory in median, respectively), however, propane and isobutane are found to be significantly underestimated in the emissions inventory (the measured values were a factor of 18 and 5.1 larger than the emissions inventory, respectively). The significant underestimate of propane can be explained by that the current emissions inventory does not consider emissions from liquefied propane gas (LPG) fueled vehicles. However, for isobutane, reasons for the underestimate are still unclear. Another field measurement has been conducted in summer of 2008, where the air samples have been collected at three different sites on the ground and by a helicopter as well. Remarkable high concentrations of 1-butene and cis- and trans-2-butenes have been sporadically observed in the samples collected at Urayasu in the coastal area of Tokyo bay. Calculated propylene equivalent (PE) concentrations of butenes revealed that those have a significantly important role in ozone formation when the air plume is affected by emissions from their emission sources. The PE concentrations of butenes varied from 0.1 to 39 ppbC, and accounted for 1.5–75% of total PE concentrations at Urayasu. Most of the continuous air quality monitoring stations does not record concentrations of individual hydrocarbons, therefore, the importance of reactive and low concentration hydrocarbon such as butenes might be overlooked in the current emissions inventory and/or air quality model. In this paper, the reliability of NMHC emissions is evaluated based on the field measurements. Their possible impacts on air quality in the Kanto area are discussed as well, based on the calculated propylene equivalent concentrations.     

Relationship of extinction coefficient, air pollution, and meteorological parameters in an urban area during 2007 to 2009

Light extinction, which is the extent of attenuation of light signal for every distance traveled by light in the absence of special weather conditions (e.g., fog and rain), can be expressed as the sum of scattering and absorption effects of aerosols. In this paper, diurnal and seasonal variations of the extinction coefficient are investigated for the urban areas of Tehran from 2007 to 2009. Cases of visibility impairment that were concurrent with reports of fog, mist, precipitation, or relative humidity above 90 % are filtered. The mean value and standard deviation of daily extinction are 0.49 and 0.39 km^?1, respectively. The average is much higher than that in many other large cities in the world, indicating the rather poor air quality over Tehran. The extinction coefficient shows obvious diurnal variations in each season, with a peak in the morning that is more pronounced in the wintertime. Also, there is a very slight increasing trend in the annual variations of atmospheric extinction coefficient, which suggests that air quality has regressed since 2007. The horizontal extinction coefficient decreased from January to July in each year and then increased between July and December, with the maximum value in the winter. Diurnal variation of extinction is often associated with small values for low relative humidity (RH), but increases significantly at higher RH. Annual correlation analysis shows that there is a positive correlation between the extinction coefficient and RH, CO, PM₁₀, SO₂, and NO₂ concentration, while negative correlation exists between the extinction and T, WS, and O₃, implying their unfavorable impact on extinction variation. The extinction budget was derived from multiple regression equations using the regression coefficients. On average, 44 % of the extinction is from suspended particles, 3 % is from air molecules, about 5 % is from NO₂ absorption, 0.35 % is from RH, and approximately 48 % is unaccounted for, which may represent errors in the data as well as contribution of other atmospheric constituents omitted from the analysis. Stronger regression equation is achieved in the summer, meaning that the extinction is more predictable in this season using pollutant concentrations.