Studies on process optimization of biodiesel production from waste cooking and palm oil

This work investigated the optimisation of biodiesel production from waste cooking oil (WCO) and palm oil using a two-step transesterification process for WCO and base catalysed transesterification for palm oil. Transesterification reactions were carried out to investigate the effects of prepared catalyst CaO, methanol/WCO and methanol/palm oil ratio and temperature on the yield of biodiesel. A series of experiments were conducted to determine the best conditions for biodiesel production, using methanol/oil ratio between 4:1 and 11:1 and contact time varying between 2 and 4 h. Biodiesel yield of around 90 and 70% was obtained for palm and waste cooking oil at the methanol/oil ratios of 6:1 and 8:1 at temperature of 60 °C for reaction time of 4 h using prepared CaO as catalyst. The physicochemical properties of palm and WCO biodiesel were carried out using standard methods, while the fatty acid profile was determined using gas chromatography. The investigation concludes that biodiesel obtained from palm and waste cooking oil was within the specified limit.     

Experimental investigation of diesel engine using EGR and fuelled with Karanja oil methyl ester

Karanja oil methyl ester (KOME), a biodiesel prepared from Karanja oil, a potential source of non-edible oil in India and a prospective alternative to the diesel fuel, shows comparable performance and considerable reduction in emissions except NO_x. Exhaust gas recirculation (EGR) is a popular method of reducing the NO_x emission. The aim of this experimental work was to study the potential of the cooled EGR in a direct injection compression ignition engine operating with the KOME and its blend. The study was conducted with the different EGR rates. Performance and emission parameters were compared by using diesel, KOME and its blend employing EGR and with the same fuels without EGR. The study also differentiates the effect of EGR on KOME and its blend with the neat diesel. The effect of EGR was found to be slightly higher for KOME biodiesel and its blend than for neat diesel. Increased NO_x emission using KOME biodiesel was also found to be reduced by using EGR.     

Gear oil formulation designed to meet bio-preferred criteria as well as give high performance

A bio-based gear oil was developed from soybean oil (SBO). The SBO was first thermally polymerised and then mixed with additives and diluents. The effect of pour point depressants, co-base oils, antioxidants and anti-wear additives is reported. Lubricity, viscosity index and oxidation stability of the final formulation of the bio-based gear oil are compared with commercially available gear oils. The final formulation of bio-based gear oil gives test results: viscosity index 165, four-ball wear scar 0.375 mm. These numbers are comparable to or better than the commercially available gear oils tested for comparison. The oxidation onset temperature of the bio-based gear oil, 220°C, is lower than the evaluated commercial products, but still at an acceptable range for gear oil.     

Synthesis of biodiesel from chicken’s skin waste by homogeneous transesterification

ABSTRACT

Poultry skin waste is considered to be a promising source of biodiesel. However, this source presents an environmental threat as it is being discharged into landfills without any treatment. We studied the feasibility of biodiesel production from poultry skin waste. Two-step extraction of lipids from chicken’s skin was developed and gave 97.5% yield using the optimum time and temperature. Esterification was then optimised to remove free fatty acids (FFA) where the ideal parameters were 65 °C during 30min with a molar ratio of methanol to oil of (1:3) and 1% of H₂SO₄. The third step was the transesterification which was performed using 60 °C and 300–600 rpm agitation for 1 h, with 1% basic catalyst and 1:3 (molar ratio) of methanol to oil. The biodiesel (FAME), was characterised using gas chromatography coupled with mass spectrometry (GC-MS) followed by chemical and physical analyses such as iodine number, acid number, flash point and cetane number. The total conversion was obtained using above conditions and most of the studied proprieties of produced biodiesel meet the EN14214 standard. This is an extremely encouraging result, offering a good source of biodiesel by valuing poultry skin waste.     

Combustion and emission characteristics of a direct injection CI engine when operated on Marotti oil methyl ester and blends of Marotti oil methyl ester and diesel

This paper presents a feasibility study of Marotti oil biodiesel as an alternative to diesel fuel for a compression ignition engine. Marotti oil is inedible and available mainly in the state of Kerala. The oil is extracted from Marotti seeds. However, the high viscosity, poor volatility and cold flow characteristics of many vegetable oils in general, and Marotti oil in particular, can cause problems such as injector coking, severe engine deposits, filter gumming, piston ring sticking and thickening of lubrication from long-term use in diesel engines. These problems can be eliminated or minimised by transesterification of the vegetable oils to form monoesters. Although transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than for petroleum diesel fuel. Subsequently, Marotti oil was converted into its methyl ester by the process of transesterification. The methyl ester was blended with diesel in various proportions to obtain different blends of Marotti oil with diesel. The performance, emission and combustion characteristics of Marotti methyl ester and its blends with diesel were studied and the results were compared with the base line data generated for diesel operation. Experiments were conducted using an injection timing of 23° before top dead centre (BTDC) and an injection pressure of 205 bar at various power outputs and at a constant rated speed of 1500 rpm. The engine manufacturer specifies an injection timing of 23° BTDC and injection pressure of 205 bar for the standard diesel fuel operation. The heat release rates, maximum rate of pressure rise, ignition delay and combustion duration for these fuel combinations were obtained.

From the results obtained, it was observed that the biodiesel produced from Marotti oil and its blends with diesel have slightly reduced brake thermal efficiency and increased smoke, hydrocarbon, carbon monoxide and reduced NO _x emissions compared with diesel-only operation. The investigation showed that the B20 biodiesel blend of Marotti oil with diesel produced better performance in terms of higher brake thermal efficiency, lower specific fuel consumption and comparatively lower emissions compared to the other blend ratios considered.     

Effect of mixing chamber venturi,injection timing,compression ratio and EGR on the performance of dual-fuel engine operated with HOME and CNG

Stringent environmental policies and the ever increasing demand for energy have triggered interest in novel combustion technologies that use alternative fuels as energy sources. Of these, pilot-ignited compressed natural gas (CNG) engines that employ small biodiesel pilot to ignite a premixed natural gas–air mixture have received considerable attention. This paper discusses the effect of mixing chamber venturi, injection timing, compression ratio and exhaust gas recirculation (EGR) on the performance of dual-fuel engine operated on biodiesel derived from honge oil and is called honge oil methyl ester (HOME) and CNG. The proposed study mainly focuses on the manifold induction of CNG along with HOME injection. However, CNG can also be injected using port or direct gas injector (Lakshmanan and Nagarajan 2010, Energy 35, pp. 3172–3178). The future study will involve these methods of CNG injection. From this study, it is concluded that an advanced injection timing and an increased compression ratio resulted in increased brake thermal efficiency and reduced smoke, hydrocarbons and carbon monoxide emissions. However, nitrogen oxides (NO _x ) emission increased significantly. The increased NO _x emission was effectively reduced with EGR method. A mixing chamber venturi of 3 mm size, injection timing of 27° before top dead centre (BTDC), compression ratio of 17.5 and 10% EGR were found to be optimum for the modified compression ignition engine that was operated on CNG–HOME dual-fuel mode.     

Performance studies of a low heat rejection engine operated on non-volatile vegetable oils with exhaust gas recirculation

During recent decades, considerable effort has been expended world-wide to reduce dependency on petroleum fuels for power generation and transportation through the search for suitable alternative fuels that are environmentally friendly. In this respect, vegetable oils are a promising alternative to diesel fuel. However, the high viscosity, poor volatility and cold flow characteristics of vegetable oils can cause some problems such as injector coking, severe engine deposits, filter gumming and piston ring sticking and thickening of lubrication from long-term use in diesel engines. These problems can be eliminated or minimised by transesterification of the vegetable oils to form monoesters. Although transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than those of petroleum diesel fuel. The performance of a diesel engine with such biodiesel operation can be improved further with the concept of the low heat rejection (LHR) engine. In the LHR engine, combustion surfaces on the pistons, cylinder walls and valves can be coated with ceramic materials. The objective of this study was to apply the LHR engine concept for improving engine performance when either honge biodiesel, known as honge oil methyl ester (HOME), or neem biodiesel, known as neem oil methyl ester (NOME) oils was used as an alternative fuel. For this purpose, experiments were conducted on a single cylinder, four-stroke, direct injection, water-cooled compression ignition engine using diesel, HOME and NOME oils at different injection timings of 19, 23 and 27° before top dead centre (BTDC) with and without the induction of exhaust gas recirculation (EGR). The percentage of EGR was varied from 5 to 20% in steps of 5%. The results showed that specific fuel consumption and brake thermal efficiency were improved for both of the biodiesel fuels in the LHR engine. An EGR of 10% resulted in better performance with trade-off between oxides of nitrogen and hydrocarbons/carbon monoxide emissions and hence 10% EGR is taken as the best of the range from 5 to 20%. However, readings with other EGR ratios are not reported.     

Comparative study on effect of blending,thermal barrier coating (LHR) and injector nozzle geometry on biodiesel-fuelled engines

Increased petroleum prices, increased threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for internal combustion engines. Evolving suitable technology for addressing energy crisis creates a continued investigation into the search for sustainable and clean-burning renewable fuels. This work investigates suitability of different non-edible-derived biodiesels such as cotton seed oil methyl ester (COME), Honne oil methyl ester (HnOME) and Rubber seed oil methyl ester (RuOME) to four stroke, single cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel blending, thermal barrier coating (TBC) or Low Heat Rejection (LHR) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and RuOME in the modified CI engine. Blends of biodiesels with diesel were varied from 20 to 80% in steps of 20%. Two thermal barrier coatings of partially stabilized zirconium (PSZ) and aluminium oxide (Al₂O₃) were provided on the engine to make it fully adiabatic. Nozzle injectors of 3, 4 and 5 holes, with size of orifice varied from 0.2 to 0.3 mm size were selected for the study. It was concluded that B20 biodiesel blend, PSZ-coated engine and four hole nozzle injector of 0.2 mm size resulted in overall better engine performance with increased brake thermal efficiency (BTE) and reduced HC, CO, smoke emissions for the fuel combinations tested. Combustion analysis to study the effect of biodiesel blends, LHR coatings, injector nozzle geometry on the performance of the biodiesel-fuelled engine has been presented to give more insight into the behaviour of operation.     

Combustion performance and emission characteristics on HCCI engine of waste plastic pyrolysis oil biodiesel blends with external PFI and vaporiser

ABSTRACT

Analysis of plastic oil obtained from waste plastic through pyrolysis process, as an alternative to biodiesel is presented in this paper. The HCCI engine is considered for experimental validation of combustion performance and emission characteristics. To accumulate pyrolysis oil as fuel, the design modifications were made in external mixture formation on the existing computerised 4-stroke, single cylinder, water cooled, direct injection kirloskar diesel engine connected with eddy current dynamometer to satisfy HCCI conditions. HCCI engine can be worked on wide assortment of fuels beginning from diesel to different blends (WPPO 5%,10%,15% and 20% by volume) of biodiesel .The designed additional device connected to the engine is utilised for fuel vaporisation and mixture arrangement. In the experimental study, the combustion results were initiate to be of 39.69 % higher Rate of Heat Release (RoHR) for biodiesel HCCI as compared with diesel HCCI. Higher brake thermal efficiency (BTE) was found 37 % without exhaust gas recirculation (EGR) at WPPO 20 % biodiesel blend. And also found 50 % and 65 % reduction in NOx emission and 18 % and 28 % reduction in smoke opacity are obtained for biodiesel vapour induction without EGR and biodiesel vapour induction with 15 % EGR as compared with diesel fuel. The CO (0.34 %), and UHC (2.15 %) emissions are increases with 15 % EGR, but the emissions are within the standard limits specified by the emissions standards.     

Blends of karanja and jatropha biodiesels for diesel engine applications

Over a number of years, the work of exploring different biodiesels as an alternative to diesel fuel has been carried out worldwide. Not much focus on the use of combination of different biodiesels and their behaviour in diesel engines has been reported. This work is an attempt in this direction, which reports on the use of combination of biodiesels derived from jatropha and karanja oils. Jatropha oil methyl ester (JOME) and honge oil methyl ester (HOME) represent the respective biodiesels derived from these non-edible oils. Experiments were conducted on a four-stroke, single-cylinder diesel engine using these biodiesel combinations in order to check their feasibility as alternative fuels to diesel. Initially, experiments were conducted on each biodiesel and their blends with diesel and engine parameters were optimised in terms of injection pressure and injection timing. Advancing the injection timing improved the overall performance of the engine fuelled with JOME while retarding the injection timing favoured the HOME. Both biodiesels performed better with an injector opening pressure of 230 bar. Finally, experiments were conducted with the combination of both biodiesels with different blend ratios. It was observed that increasing the JOME content in the biodiesels blend improved the performance with reduced emissions of smoke, hydrocarbons and carbon monoxide emissions. However NO _x emission increased.     

Effects of injection timing,injector opening pressure and nozzle geometry on the performance of cottonseed oil methyl ester-fuelled diesel engine

Increasing petroleum prices, increasing threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for engines. Evolving technology and a recurring energy crisis necessitates a continuous investigation into the search for sustainable and clean-burning renewable fuels. In this paper, cottonseed oil methyl ester (COME) was used in a four-stroke, single-cylinder variable compression ratio diesel engine. Tests were carried out to study the effects of fuel injection timing, fuel injector opening pressure (IOP) and injector nozzle geometry on the performance and combustion of COME biodiesel fuel used in a compression ignition engine with a single fuel mode. Fuel injection timing varied from 19° to 27° before top dead centre (bTDC) in incremental steps of 4° bTDC; fuel IOP varied from 210 to 240 bar in incremental steps of 10 bar. Fuel nozzle injectors with three, four and five holes, each of 0.3 mm size, were selected for the study. The results suggested that with retarded injection timing of 19° bTDC, increased IOP of 230 bar and a four-hole nozzle injector of 0.3 mm size resulted in overall better engine performance with an increased brake thermal efficiency and reduced HC, CO and smoke emission levels.     

Production of renewable and sustainable fuel from Calliandra calothyrsus and its utilisation in compression ignition engines

Alternative fuels have several advantages compared to fossil fuels as they are renewable, biodegradable, provide energy security, foreign exchange saving as well as help in addressing environmental concerns and socio-economic issues. Therefore, renewable fuels can be used predominantly as a fuel for transportation and for applications in power generation. Shaft power application is a key factor for economic growth and prosperity and depends crucially on the long-term availability of energy from sources that are affordable, accessible and environmentally friendly. In this context, the main objective of the present study was to implement the production of bioethanol from Calliandra calothyrsus, a potential lignocellulosic raw material for the cellulose-to-bioethanol conversion process that can be used as an alternative resource to starch- or sugar-containing feedstock. This study addresses a new pretreatment method known as hydrothermal explosion using C. calothyrsus for ethanol production. The present study also involves experimental investigations on a single-cylinder, four-stroke, direct-injection diesel engine operated with Honge oil methyl ester (biodiesel) and ethanol and its comparison with a neat diesel fuel mode of operation. The results revealed that optimal parameters for bioethanol production from C. calothyrsus were 2% acid concentration (HCl), 100°C temperature and 80 min retention time. For a diesel engine operated with a HOME–bioethanol blend, the experimental results showed a 3–4% decrease in brake thermal efficiency with a 8–10% increase in hydrocarbon and carbon monoxide emission levels and a 15–18% decrease in nitric oxide emission levels when compared with a neat diesel fuel mode of operation.     

Biodegradation of low-density polyethylene (LDPE) using the mixed culture of Aspergillus carbonarius and A. fumigates

Low-density polyethylene (LDPE) possesses various applications in several industries owing to its durability, low-cost, and many mechano-thermal properties. Unfortunately, LDPE waste creates an environmental threat. The level of biodegradation of black LDPE sheets with fungi isolated from different landfills sites in Sharqiyah Governorate, Egypt, was evaluated. LDPE sheets, the only source of carbon, along with minimal salt medium were incubated on a rotary shaker at 30 °C and 120 rpm for 16 weeks. Aspergillus carbonarius MH 856457.1 and A. fumigatus MF 276893 confirmed to be good candidates for LDPE biodegradation. A mixed culture of two strains showed the excellent weight loss% of sheets as compared to single isolate. Further efforts to improve the degrading capacity through physical and chemical treatments were performed. The biodegradation was significantly stimulated by 39.1% (thermal treatment), 17.76% (HNO₃ treatment), and 5.79% (Gamma-irradiation treatment). Laccases and manganese peroxidases activities were assayed. LDPE biodegradation was analyzed by scanning electronic microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and gas chromatography–mass spectrometry (GC–MS). FTIR spectra showed the appearance of new functional groups assigned to hydrocarbon biodegradation and confirmed the role of manganese peroxidase in process. The changes in the FTIR spectra of the mixed culture biomass before and after the biodegradation (Δ73 cm^?1) and the surface changes in the biodegraded LDPE (as indicated from SEM) confirmed the depolymerization of LDPE. From GC–MS analysis, the plasticizers bis(2-ethylhexyl) phthalate, Diisssctyl phthalate, 1,2-benzenedicarboxylic acid diisooctyl ester, and tributyl acetylcitrate completely biodegraded. Moreover, several antioxidants, antimicrobial, and anticancer compounds, and methyl esters of fatty acids were produced.

     

Effect of hydrogen addition to CNG in a biodiesel-operated dual-fuel engine

Alternative fuels for diesel engine applications are gaining more prominence as they have numerous advantages compared to fossil fuels. They are renewable, biodegradable; provide food and energy security and foreign exchange savings. They address environmental concerns and socio-economic issues as well. Gaseous fuels such as compressed natural gas and hydrogenated compressed natural gas (HCNG) appear more attractive fuels for diesel engine applications operated in dual-fuel mode. Such dual fuel engines can replace considerable amount of liquid-injected pilot fuels by gaseous fuels besides being friendly to the environment. A small quantity of liquid fuel injected towards the end of the compression stroke initiates combustion of the inducted gas in the dual-fuel engines. The main advantage of dual-fuel engines is their lower nitrogen oxides (NO_x) and particulate emissions. Hence renewable fuels such as biodiesels and gaseous fuels can be used predominantly for transportation and power generation applications. Gaseous fuels are clean burning and are more economical as well. A suitable carburettor was designed to supply a stoichiometric mixture of air and HCNG to the modified diesel engine operated in dual-fuel mode. The biodiesel used in this study is derived from Honge oil called the Honge oil methyl ester (HOME). This paper presents the performance, combustion and exhaust emission characteristics of a single cylinder, four stroke, direct injection, stationary diesel engine operated on HOME and HCNG in dual-fuel mode. From the results it is observed that HOME–HCNG combination gave lower brake thermal efficiency (BTE) and improved emission levels when compared with diesel/HOME in single fuel operation. Lower smoke and particulate matter were obtained with dual-fuel operation. Comparative measures of BTE, peak pressure, pressure–crank angle variation, smoke opacity, hydrocarbon, carbon monoxide and NO_x emissions have been made and analysed.     

中国生物质能政策变迁研究:2000—2019年

生物质柴油和生物质沼气是生物质能发展的两大着力点,两者在性质上存在较大差异,相应的政策设计和发展也各有不同。以政策网络理论、政策变迁相关理论为理论基础,通过搜集整理中央层面关于生物质柴油和生物质沼气的政策文本,采用政策计量和内容分析法,分析政策的发文时间、文本类型等文本外部属性特征,且根据政策文本内容划分了5类政策目标和13类政策工具,深入比较不同生物质能源在变迁中政策目标、政策工具和政策主体网络的差异。研究结果表明,中国生物质能的政策变迁,呈现多元化的演进动态:(1)生物质柴油与沼气政策的发文单位与发文类型在各时间段有所异同,整体来看,生物质柴油与沼气发文最多的单位为国务院和国家发展和改革委员会,不同的是生物质柴油发文数量位于第三位的是国家能源局,而生物质沼气是生态环境部和农业农村部。在发文类型方面,"通知与意见"类型构成了主要占比。(2)同一生物质的政策目标与工具在不同时期的政策变迁中,有延续性和差异性。例如,生物质柴油在各阶段始终以技术创新、能源供应连续性为主要政策目标来保证政策延续性,但在不同阶段也会关注环境可持续性、工业发展等;在政策工具上,生物质柴油即使在变迁中也都会使用财政支持,而各阶段配合使用的工具重心也不一致。(3)不同生物质能源使用的政策工具在同一时期也存在异同。如在第二阶段生物质柴油和生物质沼气所聚焦的政策目标和政策工具完全不同,在第一和第三阶段两者则存在小部分相似。(4)不同生物质能源的政策网络在各阶段表现存在异同。全国人民代表大会和国务院始终是政策网络中的重要主体,各个阶段不同生物质能发文主体的角色和协调互动情况随政策变迁而变化。最后,在研究结论的基础上提出政策目标与政策工具统筹运用、建立有效的政策网络主体协同治理机制的启示。     

Effect of injection timing,injector opening pressure and nozzle geometry on the performance of a compression ignition engine operated on non-edible oil methyl esters from different sources

Increasing cost of fossil fuels, environmental threats from exhaust emissions and their depleting nature have generated intense international interest in developing renewable and alternative fuels for internal combustion engines. This study investigates the suitability of different non-edible-derived biodiesels such as cottonseed oil methyl ester (COME), honne oil methyl ester (HnOME) and honge oil methyl ester (HOME) to four-stroke, single-cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel injection timing (IT), fuel injector opening pressure (IOP) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and HOME in the modified CI engine. IT was varied from 19° to 27° before top dead centre (bTDC) in steps of 4° bTDC; IOP was varied from 205 to 240 bar in steps of 10 bar. Nozzle injectors of three to five holes, each of 0.3 mm size, were selected for the study. It was concluded that a retarded IT of 19° bTDC increased IOP of 230 bar, and four-hole nozzle injector of 0.3 mm size resulted in overall better engine performance with increased brake thermal efficiency and reduced hydrocarbon and carbon monoxide smoke emissions for the fuels tested.     

Effects of compression ratio,swirl augmentation techniques and ethanol addition on the combustion of CNG–biodiesel in a dual-fuel engine

The diminishing resources and continuously increasing cost of petroleum in association with their alarming pollution levels from diesel engines has led to an interest in finding alternative fuels to diesel. Emission control and engine efficiency are two of the most important parameters in current engine design. The impending introduction of emission standards such as Euro IV and Euro V has forced research towards developing new technologies for combating engine emissions. This paper examines the effects of compression ratio, swirl augmentation techniques and ethanol addition on the combustion of compressed natural gas (CNG) blended with Honge oil methyl esters (HOME) in a dual fuel engine. The present results show that the combustion of HOME and 15% ethanol blend with CNG induction in a dual-fuel engine operated in optimized parameters at an injection timing of 27° Before Top Dead Centre and a compression ratio of 17.5 resulted in acceptable combustion emissions and improved brake thermal efficiencies. The implementation of swirl augmentation techniques increased brake thermal efficiencies (BTEs) and considerably reduced combustion emissions such as smoke, HC, CO and NO_x. The addition of ethanol also increased BTEs. However, at more than 15% of ethanol in HOME, NO_x emissions increased dramatically.     

Combustion characteristics of a four-stroke CI engine operated on Honge and Jatropha oil methyl ester–ethanol blends when directly injected and dual fuelled with CNG induction

The demand for petroleum products in India has been increasing at a rate higher than the increase of domestic availability. At the same time, there is continuous pressure on emission control through periodically tightened regulations particularly in metropolitan cities. In the wake of this situation, there is an urgent need to promote the use of alternative fuels as substitutes for high-speed diesel. Dual-fuel mode of operation employing compressed natural gas (CNG) and plant oils such as Honge and Jatropha oils and their esters is an attractive option as our country has a large agriculture base that can be a feedstock to this fuel technology which can ease the burden on the economy by curtailing fuel imports. This paper presents the results of investigations carried out in studying the behaviour of Honge and Jatropha oil methyl esters and their blends with 15% ethanol and subsequent testing of these oils in a four-stroke, single-cylinder, water-cooled, direct-injection compression ignition engine in dual-fuel mode with CNG induction.     

Phytomonitoring the unique colonization of oil-contaminated saline environment by Limoniastrum monopetalum (L.) Boiss in Egypt

A site that covers over 20 acres of coastal saline depression in the western Mediterranean coastal desert of Egypt (El-Hammra station, the main crude oil pipeline terminal in Al-Alamein) is contaminated with crude oil spill as a result of activities from refineries, oilfield blowouts, tanker and pipeline break-ups. This area, prior to contamination, was dominated by different common halophytes. However, Limoniastrum monopetalum is now the only species found growing in the oil-contaminated soil. A specific question addressed in the present study was: what are the biochemical changes occurring in a desert plant growing in oil-contaminated soils? Major metabolites such as proline, betaine, free amino acids, fatty acid esters and mineral elements were studied. The plant samples were collected from the oil-contaminated, as well as noncontaminated, sites. The higher concentration in the selected organic metabolites in the plants growing in the contaminated site compared to those in noncontaminated site may be due to differences in a number of receptors. The sensitivity of such receptors for the environmental signal that cause differences in genetic expression leads to differences in physiological processes. The change in the landscape of the contaminated area and the elimination of the natural vegetation, except L. monopetalum, may explain the competitive balance toward the oil-resistant species.     

Effects of EGR on performance and emissions of a diesel engine fuelled with balanites aegyptiaca/diesel blends

In this study, balanites Aegyptiaca (L.) Del biodiesel was blended in proportions of 10% and 20% on the volume basis with diesel fuel and tested in a single cylinder, VCR diesel engine under measured load conditions with varied EGR rates (0, 10 and 20%). The results showed that B10 and B20 blends shown a significant reduction rate in terms of NO_x emissions that were familiar with biodiesel blends. At peak load conditions, BTE increased slightly for test fuel blends compared with pure diesel fuel while the BSFC rate and EGT suffered from increasing and decreasing nature with respect to blending percentage. From the emissions point of view, with the increase in blends percentage, a significant reduction rate is observed in terms of CO and HC concentrations (up to 12.34 and 17.5%, respectively) while NOx emissions decreased at peak load conditions (up to 24.34%). HC and CO emissions decreased with increase in blends percentage. However, lower levels of NO_x and EGT (up to 21.37 and 8.47%, respectively) and the average increase in terms of BTE and BSFC (up to 2.83 and 2.9%, respectively) can be realised with B20 test fuel blend under 20% EGR rate.