固相萃取—气相色谱质谱法测定水样中的毒死蜱及其代谢产物

建立了水样中毒死蜱及其主要代谢产物3,5,6-三氯吡啶醇(TCP)的固相萃取—气相色谱质谱检测法,即采用固相萃取对水样中的毒死蜱及其代谢产物TCP进行富集,浓缩后经双(三甲基硅烷基)三氯乙酰胺(BSTFA)衍生TCP,采用气相色谱质谱进行测定。同时,采用外标法对毒死蜱和TCP进行定量。结果表明,该方法的线性范围为20~1 000μg/L,毒死蜱和TCP的检出限分别为0.375、0.100μg/L;环境水样中的毒死蜱和TCP平均加标回收率分别为89.12%~93.44%和87.37%~90.75%,相对标准偏差(RSD)为2.79%~6.64%和1.22%~5.48%。     

分散固相萃取法萃取再生水中DBP与DEHP

为定量分析再生水中邻苯二甲酸二丁酯(DBP)和邻苯二甲酸二(2-乙基己基)酯(DEHP)痕量环境激素,考察了分散固相萃取(DSPE)预处理方法的萃取条件,并用于实际再生水样的预处理分析。结果表明,当萃取剂(HC-C18)用量为0.20 g、洗脱剂为6 m L乙酸乙酯、萃取时间为20 min、摇床振荡速度为200 r·min~(-1)、萃取温度为50℃时,DBP与DEHP回收率分别为96.91%和101.82%。2种物质在0.50~50.00μg·L~(-1)范围内线性良好,相关系数(R2)分别为0.998 6和0.998 8,检出限分别是0.05和0.008μg·L~(-1),加标回收率平均为96.58%和97.23%,相对标准偏差分别为3.37%~8.29%和4.91%~5.74%。该方法无需过滤水样,能够减少目标物在过滤过程中的损失,预处理时间短,且不会造成萃取小柱堵塞,适用于水质变化大、悬浮物含量高的再生水分析。采用DSPE-GC-MS方法对再生水中DBP、DEHP检测分析,方法的准确度和精密度满足痕量物质分析要求。     

在线固相萃取液质联用法测定饮用水源中的痕量联苯胺

建立了在线固相萃取液相色谱串联质谱法测定水中痕量联苯胺的方法。样品经自动进样器注入在线固相萃取小柱后,用富集泵流动相实现对样品的富集洗脱,然后用分析泵流动相将样品从富集柱冲洗至色谱柱后用串联质谱仪进行检测。该方法可在11 min内自动完成对样品的富集、净化、进样和检测过程。当进样量为5 m L时,联苯胺在0.010~2.0μg·L~(-1)范围内具有良好的线性关系,相关系数R为0.999,检出限为0.8 ng·L~(-1),实际水样的回收率为85%~104%。该方法具有简单、快速、重现性好、灵敏高等特点,可用于环境水体中痕量联苯胺的检测。     

SPE-HPLC法检测环境水样中的痕量三氯卡班

建立了环境水样中三氯卡班(TCC)的预处理和测定方法。考察了3种固相萃取(SPE)小柱、5种洗脱液对TCC回收率的影响。结果表明,采用ENVI-18 SPE小柱、以乙酸乙酯/乙腈(1∶1)为洗脱液、高效液相色谱仪-紫外检测器(HPLC-UV)检测,以蒸馏水为背景溶液TCC的加标回收率高达95%,仪器检出限与定量限分别为2.37与7.89μg/L。该方法用于实际环境水样,TCC加标浓度1~10μg/L,污水厂进水、出水与地表水中TCC的加标回收率分别在89.38%~96.90%、87.74%~94.34%与83.64%~94.61%之间,表明所建立的SPE-HPLC法适合城市生活污水和地表水中痕量TCC的检测。运用该方法测定实际环境水样中的TCC含量,集美污水处理厂进水与出水中TCC浓度分别为1.35与0.22μg/L;华大污水厂进水与出水中TCC浓度分别为1.05与0.53μg/L;白鹭湖水样中的TCC浓度为1.11μg/L。     

碳纳米管顶空固相微萃取-气相色谱法测定土壤中有机氯农药

采用碳纳米管顶空固相微萃取-气相色谱法测定了土壤中有机氯农药,探讨了萃取时间、萃取温度、搅拌速度、离子强度、有机溶剂和土壤加水量对萃取效率的影响.该方法的线性范围为0.5～50.0 ng/g,r0.991 5,检出限为0.03～0.33 ng/g.样品的加标回收率为91.4%～120.0%,相对标准偏差不大于12.7%.     

添加给水厂残泥对稻田土壤中毒死蜱环境赋存及厌氧降解的影响

给水厂残泥(WTR)是给水厂混凝过程产生的安全废弃物,是一种高效低廉的毒死蜱吸附材料。为评估将WTR作为吸附材料添加于土壤中缓解毒死蜱危害的可行性,探究了添加WTR对稻田土壤中毒死蜱环境赋存、厌氧降解及其代谢产物TCP形成的影响。实验结果表明:毒死蜱首要厌氧降解途径是快速水解为TCP,添加WTR显著降低了土壤中毒死蜱与TCP的生物有效性(P0.05)。72 d厌氧培养时间内,未添加WTR土壤中高达79%的毒死蜱主要以生物可利用态存在;在WTR添加土壤中,72%~95%的毒死蜱以稳定的残渣态存在,但毒死蜱在土壤中的降解速度因此减慢,TCP生成量随之减少。在未添加WTR土壤中,92%以上的TCP以水溶态为主,添加WTR可有效减少其水溶态所占比例,WTR添加量为10%时,其水溶态含量降至47%。随着WTR添加量增加,毒死蜱与TCP由土壤向上覆水迁移的量显著减少(P0.05)。未添加WTR的土壤水溶液体系上覆水中毒死蜱和TCP浓度分别高达537μg·L~(-1)和1 750μg·L~(-1),添加2%WTR可使其最高浓度分别降低50%。在厌氧滞水的稻田土壤中,WTR主要金属元素(Fe、Al和Mn)稳定性强,二次污染风险较低。综合以上研究结果,WTR适于作为土壤添加物应用于毒死蜱与TCP污染控制。     

聚丙烯基改性纤维固相萃取水中的苯酚

通过高能电子束辐照的方法,在聚丙烯（PP）纤维基体上分别接枝长链丙烯酸十八酯（SA）和亲水性丙烯酸-β-羟乙酯（HEA）2种单体,并将该纤维作为固相萃取填料,用于固相萃取（SPE）水中的痕量苯酚。研究了SPE过程中上样速度、洗脱溶剂、洗脱体积以及洗脱速度等因素对纤维萃取效果的影响。结果表明,改性纤维对痕量苯酚的富集倍数达95~145倍,回收率达到90%~98%,甲醇对纤维有良好的再生效果,纤维重复使用6次以内时,吸附性能无明显变化。     

微生物发酵产物中溶藻物质的提取方法

微生物溶藻是藻类水华控制的研究热点,但目前仍缺乏去除微生物发酵产物中营养物质的方法学研究,对野外水体采集的微囊藻的溶藻活性研究也较少见。比较了不同极性溶剂对溶藻物质的固液萃取效率,研究了分子筛层析对溶藻物质的纯化效果,并测定了各提纯步骤的中间产物对野外水体采集的铜绿微囊藻的溶藻效果。结果表明,在溶藻活性基本保持稳定的前提下,固液萃取串联分子筛层析技术对TOC、TN和TP的总去除率平均高达97%,其中,固液萃取的分级去除率平均高达90%,而分子筛层析的分级去除率平均为70%,且分子筛层析后的产物对野外水体采集的铜绿微囊藻的去除率稳定在60%左右。结果说明,固液萃取与分子筛层析技术可以作为溶藻物质工业化提取与实验室纯化的重要方法。     

A/O/O生物流化床处理焦化废水中酚类组成及降解特性分析

为了研究实际焦化废水处理工程中酚类污染物的组成及降解特性,实验中采用HLB小柱固相萃取水样,GC-MS选择性离子扫描方法检测环境中15种酚类污染物,除苯酚的平均回收率为72.6%以外,其他14种酚类的回收率在87.6%~102.3%之间,平行测定标准偏差均小于7.62%,能够满足环境中酚类污染物测定的需要。实验结果表明,焦化废水中含有高浓度的苯酚、甲基酚和萘酚,同时存在微量的氯酚和硝基酚。在生物流化床A/O/O组合工艺处理焦化废水的过程中,厌氧阶段高浓度酚类(苯酚、甲基酚和萘酚)、氯酚类去除率分别为29.3%和31.6%;一级好氧阶段分别为99%和92.4%;二级好氧阶段分别达到89%和6%;最终出水中酚类污染物浓度0.045 mg/L,满足钢铁行业废水达标排放要求。     

介绍一种测定土壤中芳烃化合物的方法

Millersville大学的托马斯G·格里科和Villanova大学的罗伯特L·格劳伯将液相萃取法,固相萃取浓缩法、毛细管气相色谱法配合起来测定土壤中芳烃化合物。其中新颖之处在于固相萃取浓缩法的应用。土壤中的芳烃化合物需先用溶剂萃取后再进行测定。由于使用大量的萃取溶剂,萃取后必须将溶剂蒸发至小剂量以浓缩被分析的化合物,才能进行测定,但土壤及污泥中有毒物质的去除及其后的测定将因此受到影响。在分析化学界,固相萃取浓缩法已被认可。该方法为:使用一小型固相色谱柱(ca,lg)滞留和浓缩液体萃取品中的被分析物,然后小心翼翼地     

Sorption and desorption of Cu and Cd by macroalgae and microalgae

The sorption and desorption of Cu and Cd by two species of brown macroalgae and five species of microalgae were studied. The two brown macroalgae, Laminaria japonica and Sargassum kjellmanianum, were found to have high capacities at pHs between 4.0 and 5.0 while for microalgae, optimum pH lay at 6.7. The presence of other cations in solution was found to reduce the sorption of the target cation, suggesting a competition for sorption sites on organisms. Sorption isotherms obeyed the Freundlich equation, suggesting involvement of a multiplicity of mechanisms and sorption sites. For the microalgae tested, Spirulina platensis had the highest capacity for Cd, followed by Nannochloropsis oculata, Phaeodactylum tricornutum, Platymonas cordifolia and Chaetoceros minutissimus. The reversibility of metal sorption by macroalgae was examined and the results show that both HCl and EDTA solutions were very effective in desorbing sorbed metal ions from macroalgae, with up to 99.5% of metals being recovered. The regenerated biomass showed undiminished sorption performance for the two metals studied, suggesting the potential of such material for use in water and wastewater treatment.     

Kinetic and structural relationships of transition monomeric and oligomeric carboxyl- and choline-esterases

The kinetic and structural relationships of eight electrophoretically pure mammalian serum and liver serine carboxylesterases (CE) and cholinesterases (ChE) have been studied. Eight CE's and ChE's, which were fully resolved but only partially purified, provided additional information. Five of the electrophoretically pure esterases were monomeric, and of these, four belonged to a new and widely distributed class. These four monomeric esterases hydrolyzed choline esters, but at widely differing rates. Thus two were termed monomeric butyrylcholinesterases, mBuChE I and II, and two were monomeric CE's (mCE). The rabbit liver mCE was not a subunit of the oligomeric CE (oCE), although the oCE also hydrolyzed choline esters at a very low rate. The complex kinetics of the mCE's, mBuChE's, oCE's, and of the oligomeric BuChE's of horse and human serum could be interpreted according to a single reaction scheme involving an allosteric site and the equation derived from it. Thus activation and inhibition at high substrate concentrations, together with sigmoidal activity versus substrate concentration plots, all of which characterize the reactions of these esterases, could be interpreted by a single scheme and equation. Structural and kinetic comparisons showed a progressive transition of properties from the oCE's through the mCE's to the oBuChE's. One of the purified mCE's was from horse serum, and it exhibited physical and kinetic properties unlike those of the liver mCE's or oCE's.     

Persistence and dissipation kinetics of trifloxystrobin and tebuconazole in onion and soil

The persistence and dissipation kinetics of trifloxystrobin and tebuconazole on onion were studied after application of their combination formulation at a standard and double dose of 75 + 150 and 150 + 300 g a.i. ha^?1. The fungicides were extracted with acetone, cleaned-up using activated charcoal (trifloxystrobin) and neutral alumina (tebuconazole). Analysis was carried out by gas chromatograph (GC) and confirmed by gas chromatograph mass spectrometry (GC-MS). The recovery was above 80% and limit of quantification (LOQ) 0.05 mg kg^?1 for both fungicides. Initial residue deposits of trifloxystrobin were 0.68 and 1.01 mg kg^?1 and tebuconazole 0.673 and 1.95 mg kg^?1 from standard and double dose treatments, respectively. Dissipation of the fungicides followed first-order kinetics and the half life of degradation was 6–6.6 days. Matured onion bulb (and field soil) harvested after 30 days was free from fungicide residues. These findings suggest recommended safe pre-harvest interval (PHI) of 14 and 25 days for spring onion consumption after treatment of Nativo 75 WG at the standard and double doses, respectively. Matured onion bulbs at harvest were free from fungicide residues.     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Sorption and desorption behavior of chloroanilines and chlorophenols on montmorillonite and kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Bacterial and archaeal diversity in oil fields and reservoirs and their potential role in hydrocarbon recovery and bioprospecting

Environmental Science and Pollution Research - Hydrocarbon is a primary source of energy in the current urbanized society. Considering the increasing demand, worldwide oil productions are declining...     

畜禽养殖业污染与循环经济

解决畜禽养殖业的污染问题要以充分利用资源为根本出发点，通过对污染全过程控制及废物综合利用，达到畜禽粪便的减量化、无害化、资源化，走循环经济的发展道路。     

Degradation in soil and water and ecotoxicity of rimsulfuron and its metabolites.

The degradation and ecotoxicity of sulfonylurea herbicide rimsulfuron and its major metabolites were examined in batch samples of an alluvial sandy loam and in freshwater. An HPLC-DAD method was adapted to simultaneously identify and quantify rimsulfuron and its metabolites, which was successfully validated by GC-MS analysis. In aqueous solutions, pure rimsulfuron was rapidly hydrolyzed into metabolite 1 (N-(4,6-dimethoxypyrimidin-2-yl)-N-(3-(ethylsulfonyl)-2-pyridinylurea)), which itself was transformed into the more stable metabolite 2 (N-((3-(ethylsulfonyl)-2-pyridinyl)-4,6-dimethoxy-2-pyrimidineamine)), with half-life (t(1/2)) values of 2 and 2.5 days, respectively. Hydrolysis was instantaneous under alkaline conditions (pH = 10). In aqueous suspensions of the alluvial soil (pH = 8), formulated rimsulfuron had a half-life of 7 days, whereas that of metabolite 1 was similar to that in water (about 3.5 days). The degradation of the two major metabolites was also studied in soil suspensions with the pure compounds at concentrations ranging from 1 to 10 mg l(-1). The half-life of metabolite 1 ranged from 3.9 to 5 days, close to the previous values. Metabolite 2 was more persistent and its degradation is strongly dependent on the initial concentration (C0): half-life values ranged from 8.1 to 55 days at 2-10 mg l(-1), respectively. These values are higher than those determined from the kinetics of metabolite 1 transformation into metabolite 2 (t(1/2) = 8-19 days). The ecotoxicity of the three chemicals was evaluated through their effect on Daphnia magna and Vibrio fischeri (Microtox bioassay). No effect was observed on D. magna with 24 and 48 h acute toxicity tests. Similarly, no toxic effect was observed with the Microtox test for the three chemicals in the range of concentrations tested that included the field application dose. Thus, being of low persistence and lacking acute toxicity, these chemicals present a low environmental risk. However, chronic effects should be studied in order to confirm the safety of rimsulfuron and its major metabolites.     

Isocyanatocyclohexane and isothiocyanatocyclohexane levels in urban and industrial areas and possible emission-related activities

Isocyanatocyclohexane and isothiocyanatocyclohexane are becoming relevant compounds in urban and industrial air, as they are used in important amounts in automobile industry and building insulation, as well as in the manufacture of foams, rubber, paints and varnishes. Glass multi-sorbent tubes (Carbotrap, Carbopack, Carboxen) were connected to LCMA-UPC pump samplers for the retention of iso- and isothiocyanatocyclohexanes. The analysis was performed by automatic thermal desorption (ATD) coupled with capillary gas chromatography (GC)/mass spectrometry detector (MSD). TD-GC/MS was chosen as analytical method due to its versatility and the possibility of analysis of a wide range of volatility and polarity VOC in air samples. The method was satisfactory sensitive, selective and reproducible for the studied compounds. The concentrations of iso- and isothioisocyanatocyclohexanes were evaluated in different urban, residential and industrial locations from extensive VOC air quality and odour episode studies in several cities in the Northeastern edge of Spain. Around 200–300 VOC were determined qualitatively in each sample. Higher values of iso- and isothiocyanatocyclohexane were found in industrial areas than in urban or residential locations. The concentrations ranged between n.d.−246 and n.d.−29 μg m⁻³ for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively, for industrial areas. On the other hand, urban and residential locations showed concentrations ranging between n.d.−164 and n.d.−29 μg m⁻³ for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively. The site location (urban or industrial), the kind and nearness of possible iso- and isothiocyanatocyclohexane emission activities (industrial or building construction) and the changes of wind regimes throughout the year have been found the most important factors influencing the concentrations of these compounds in the different places.