基于风险的液化烃罐区建筑物抗爆荷载评估方法

为合理确定液化烃罐区周边建筑物的抗爆设防荷载,有效进行抗爆设计和防护,建立1套系统的抗爆设防荷载定量评估方法。以某液化烃罐区建筑物为例,计算172个爆炸场景,获得4组累积爆炸频率曲线,基于风险控制标准确定抗爆设防荷载。结果表明:爆炸场景发生频率应包括初始泄漏频率、气象概率、泄漏方向概率和延迟爆炸概率;获得的爆炸超压-累积频率曲线是确定抗爆设防荷载的基础,在爆炸超压较低时,与爆炸源中心距离不同的4面墙体的超压累积频率曲线极为接近;随着爆炸超压的继续增大,累积发生频率的差异逐渐明显;液化烃罐区建筑物的抗爆设防荷载应同时满足2个准则,即万年1次的风险可接受准则和风险可接受范围内爆炸超压最大化准则;根据该准则确定的液化烃罐区附近建筑物东墙的爆炸冲击波峰值入射超压为44.6 kPa,正压作用时间为89.3 ms。     

埋地输氢管道泄漏爆炸事故后果模拟分析

为了输氢管道的安全建设与运营,基于计算流体力学FLACS软件,模拟了埋地输氢管道在半受限空间内的泄漏爆炸事故后果,探讨了泄漏孔径、泄漏时长、输氢压力和环境风速对爆炸事故后果的影响规律,并得出相应的危险区域。结果表明:泄漏孔径、输氢压力和最大爆炸超压均与危险区域呈正相关关系,泄漏时长对事故后果几乎无影响;随着输氢压力的增大,危险区域受建筑物和风速的影响更为明显,在建筑物附近形成了狭长的危险区域带;最大爆炸超压和危险区域随环境风速的增大均呈现出先增大后减小的趋势。     

Mitigation performance of the process protection system on the accident consequences of H2S-containing natural gas release and explosion

Toxic loads and explosion overpressure loads pose grave threats to the offshore oil and gas industry. Many safety measures are adopted to prevent and mitigate the adverse impacts caused by toxic loads and explosion overpressure loads. As a general safety barrier, the process protection system has been widely used but rarely evaluated. In order to assess the barrier ability, the mitigation performance of the process protection system is concerned in this study. Firstly, several chain accidents of H₂S-containing natural gas leakage and explosion are simulated by varying the response time of the process protection system with CFD code FLACS. Qualitative assessment is conducted based on the variation of the dangerous load profiles. Furthermore, the quantitative assessment of the mitigation performance is accomplished by considering its ability in reducing the probability of fatality. Emergency evacuation and no emergency evacuation are considered respectively in the quantitative assessment. The results prove that the process protection system takes effect on mitigating the toxic impact and explosion overpressure impact. The results also demonstrate that although the emergency evacuation may result in a severer explosion load to the operator, the process protection system can mitigate the adverse impacts regardless of whether the emergency evacuation is conducted or not.     

基于FLACS的LNG船舶泄漏爆炸过程数值模拟研究

为研究大尺寸、全场景下LNG船舶卸货作业过程中的泄漏爆炸风险,构建某LNG接收站及其周边20.5 km2的区域场景模型,采用FLACS软件数值模拟LNG泄漏扩散、气云爆炸的演化过程.结果表明:LNG从卸料臂处以满输速率持续泄漏5 min,最大液池面积17 047 m2,最大汽化速率350 kg/m3,遇点火源发生气云爆...     

Experimental study on the minimum explosion concentration of anthracite dust: The roles of O2 mole fraction,inert gas and CH4 addition

The explosion characteristics of anthracite coal dust with/without small amount of CH₄ (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (P_ex) and the rate of explosion pressure rise ((dp/dt)_ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N₂ with CO₂, suggesting that CO₂ has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH₄ moderates the inhibition effect of CO₂ and the promotion effect of O₂ on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH₄ mixture explosions, Barknecht's curve was found to be more accurate and conservative than Chatelier's line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.     

城镇燃气管道泄漏爆炸的定量风险分析

介绍了城镇燃气管道泄漏爆炸冲击波超压的定量风险分析方法.简要介绍了城镇燃气管道,对城镇燃气管道泄漏的失效概率、泄漏源模型、爆炸冲击波超压模型、超压概率模型、个人风险和社会风险分别作了论述.     

Computer simulation of shock waves transmission in obstructed terrains

Generation and transmission of blast waves in real terrains is of major importance for risk analysis procedures involving accidental explosion scenarios. The problem arises from the impact of overpressure wave on people and structures that may be lethal or catastrophic under certain conditions. In this paper, a CFD simulation of shock wave propagation in obstructed terrain is attempted. Overpressure histories as well as a series of critical parameters, namely the positive and negative peak overpressure, the arrival time, and the positive and negative phase duration at specific points within the domain were obtained during the simulation. Their comparison with experimental measurements from field-scale high explosive blast tests performed by HSE showed a reasonably good agreement indicating that CFD computer programs provide reliable tools for estimating explosive shocks in complex terrains.     

Experimental study on water sealing of fire barriers and explosion venting of large-scale pipeline with low-concentration gas

Low-concentration gas transported in pipelines may lead to explosion accidents because gas with a concentration of less than 30% is prone to explode. To reduce the incidence of gas explosions, water sealing of fire barriers is implemented, and explosion venting devices are installed along the pipeline. To investigate their suppression effect on low-concentration gas explosion, experiments using methane–air premixed gas under different conditions were implemented on a DN500 pipeline test system. The effects of three types of explosion venting forms (rupture disc, asbestos board, and plastic film) on explosion overpressure and flame were compared and analysed. Results show that the rupture disc, asbestos board, and plastic film can achieve adequate explosion venting, causing the peak decay rates of explosion overpressure to reach 82.37%, 81.72%, and 90.79%, respectively. The foregoing indicates that the greater the static activation pressure of the explosion venting form, the higher the peak explosion overpressure at each measurement point. Moreover, the shorter the explosion flame duration, the greater the flame propagation velocity. The research results provide an essential theoretical foundation for the effective suppression of gas explosion accidents in the process of low-concentration gas transportation.     

Influence of vacuum degree on the effect of gas explosion suppression by vacuum chamber

In order to study the influence of vacuum degree on gas explosion suppression by vacuum chamber, this study used the 0.2 mm thick polytetrafluoroethylene film as the diaphragm of vacuum chamber to carry out a series of experiments of gas explosion suppression by vacuum chamber with the vacuum degree from −0.01 MPa to −0.08 MPa. The experimental results show that: under the condition of any vacuum degree, vacuum chamber can effectively suppress the explosion flame and overpressure; as vacuum degree changes, the effect of gas explosion suppression using vacuum chamber is slightly different. Vacuum chamber has obvious influence on propagation characteristics of the explosion flame. After explosion flame passes by vacuum chamber, the flame signal weakens, the flame thickness becomes thicker, and the flame speed slows down. With the increase of the vacuum degree of vacuum chamber, the flame speed can be prevented from rising early by vacuum chamber. The higher the vacuum degree is, the more obviously the vacuum chamber attenuates the explosion overpressure, the smaller the average overpressure is, and the better effect of the gas explosion suppression is. Vacuum chamber can effectively weaken the explosion impulse under each vacuum degree. From the beginning of −0.01 MPa, the vacuum chamber can gradually weaken explosion impulse as the vacuum degree increases, and the effect of gas explosion suppression gradually becomes better. When the vacuum degree is greater than −0.04 MPa, the increase of vacuum degree can make the explosion overpressure decrease but have little influence on the explosion impulse. Therefore, the vacuum chamber has the preferable suppression effect with equal to or greater than −0.04 MPa vacuum degree.     

Insight into vented explosion mechanism and premixed flame dynamics in linked vessels: Influence of membrane thickness and blocking rate

To effectively prevent and mitigate explosion hazards and casualties, relief venting of flammable gas explosions has been applied in production processes in a broad variety of industries. This work conducted fully vented experiments to investigate the influence of venting membrane thickness, and partially vented experiments to investigate the influence of baffle blocking rate on the explosion characteristics of 9.5 vol% methane-air mixtures in linked vessels with a 0.5 m long vented duct. Results indicate that the membrane thickness and blocking rate for the two types of vented explosions significantly affected the explosion overpressure. The smaller the membrane thickness and blocking rate, the lower the explosion overpressure. Secondary explosions were observed in the vented duct through experiments and a weaker explosion flame appeared at a small blocking rate of 20%. With the further increase in the blocking rate, the flame became extremely weak, and no secondary explosions occurred. The overpressure evolution process at different positions in the explosion duct and secondary explosion phenomenon in the vented duct were investigated. This work could probably serve as an important reference for the selection of technical parameters of explosion venting in the practical industrial processes.     

A new simple methodology for evaluation of explosion risk in underground coal mines

The key objective of this paper is the presentation of a new risk assessment tool for underground coal mines based on a simplified semi-quantitative estimation and assessment method.In order to determine the risk of explosion of any work process or activity in underground coal mines it is necessary to assess the risk. The proposed method is based on a Risk Index obtained as a product of three factors: frequency of each individual scenario P_ucm, associated severity consequences C_ucm and exposure time to explosive atmospheres E_ucm. The influence of exposure time is usually not taken into account up to now. Moreover, the exposure to explosive atmospheres may affect factors of hazardous event probability as much as its consequences. There are many definitions of exposure to explosive atmospheres but in the case of underground coal mines the exposure is defined as frequency risk of firedamp and coal dust. The risk estimation and risk assessment are based on the developed of a risk matrix.The proposed methodology allows not only the estimation of the explosion risk but also gives an approach to decide if the proposal investment is well-justified or not in order to improve safety.     

基于FLACS的海上钻探平台井喷爆炸事故后果模拟分析*

为研究海上钻探平台井喷燃爆事故后果,运用FLACS软件对某深海钻探平台井喷爆炸事故进行模拟,研究在不同事故场景下气云爆炸发展过程及平台荷载分布规律,讨论井喷速率、风向、点火位置等对爆炸超压的影响。研究结果表明:随泄漏速率增加,爆炸强度和爆炸范围均增大,爆炸严重程度不仅与井喷速率密切相关,同时也受平台结构影响;点火位置会对爆炸超压产生影响,在可燃气体与空气混合气体比例为化学理论当量比处点燃气体,生活区承受的爆炸超压最大;在设施及建构筑物分布较为密集、拥塞度较高的地方产生的爆炸超压更大。研究结果可为可为平台的阻隔防爆性能设计与应急响应提供指导。     

Experimental study on explosion characteristics of ethanol-gasoline blended fuels

In the present work, a series of experiments have been performed to analyze the explosion characteristics of ethanol-gasoline with various blended ratios (0%, 5%, 10%, 15%, 30%, 50%, 70%, 80%, and 100%). A vented rectangular vessel with a cross-section of 100 mm × 100 mm, 600 mm long and a 40 mm diameter vent on the top is used to carry out the experiments. The flame propagation is recorded by a phantom high-speed camera with 5000 fps, while the histories of the explosion overpressure are measured by two PCB pressure sensors and the explosion sound pressure level is obtained by a CRY sound sensor. The results indicate that the maximum overpressure and flame propagation speed increases linearly as the blended ratio increases when the initial volume of blended fuel is 1.0 mL; While the change of explosion overpressure and flame propagation speed shows a trend of decreasing at first and then increasing as the concentration increases to 1.8 mL. It is also found that the peak of the sound pressure level exceeds 100 dB under all tests, which would damage the human's hearing. What's more, relationships between explosion overpressure and sound pressure level are examined, and the change of the maximum overpressure can be reflected to some extent by the measurement of the maximum sound pressure level. The study is significant to reveal the essential characteristic of the explosion venting process of ethanol-gasoline under different initial blended ratios, and the results would help deepen the understanding of ethanol-gasoline blended fuels explosion and the assessment of the explosion hazardous.     

Enhancement effects of methane/air explosion caused by water spraying in a sealed vessel

Experiments about the influence of ultrafine water mist on the methane/air explosion were carried out in a fully sealed visual vessel with methane concentrations of 8%, 9.5%, 11% and 12.5%. Water mists were generated by two nozzles and the droplets' Sauter Mean Diameters (SMD) were 28.2 μm and 43.3 μm respectively which were measured by Phase Doppler Particle Anemometer (PDPA). A high speed camera was used to record the flame propagation processes. The results show that the maximum explosion overpressure, pressure rising rate and flame propagation velocity of methane explosions in various concentrations increased significantly after spraying. Furthermore, the brightness of explosion flame got much higher after spraying. Besides, the mist with a larger diameter had a stronger turbulent effect and could lead to a more violent explosion reaction.     

基于CFD的半封闭空间内LNG泄漏后果研究

为定量分析半封闭空间内液化天然气（LNG）泄漏后果,利用计算流体力学（CFD）软件FLUENT,对不同条件下的“冷箱”内LNG泄漏后扩散与爆炸过程进行了模拟。结果表明:无论通风与否,危险区域（甲烷体积分数为5%~15%）一直存在,但通风时该区域比无通风时小; LNG泄漏后会导致箱内温度降低,且泄漏量越大温度下降越低,但通风在一定程度上能减小温降; 当危险区域最大时,发生爆炸产生的超压最大,对于泄漏量小的情况,通风能减小爆炸压力; 障碍物的存在会增大爆炸压力,研究中的最大爆炸超压为158 kPa,可对设备与人员造成严重危害,故在设计“冷箱”时须提出相应的强度要求。研究方法与结果对于与“冷箱”类似的受限空间安全设计与风险评估有指导意义。     

Fire and explosion hazard analysis during surface transport of liquefied petroleum gas (LPG): A case study of LPG truck tanker accident in Kannur,Kerala, India

This paper presents an analysis and simulation of an accident involving a liquefied petroleum gas (LPG) truck tanker in Kannur, Kerala, India. During the accident, a truck tanker hit a divider and overturned. A crack in the bottom pipe caused leakage of LPG for about 20 min forming a large vapor cloud, which got ignited, creating a fireball and a boiling liquid expanding vapor explosion (BLEVE) situation in the LPG tank with subsequent fire and explosion. Many fatalities and injuries were reported along with burning of trees, houses, shops, vehicles, etc. In the present study, ALOHA (Area Locations of Hazardous Atmospheres) and PHAST (Process Hazard Analysis Software Tool) software have been used to model and simulate the accident scenario. Modeling and simulation results of the fireball, jet flame radiation and explosion overpressure agree well with the actual loss reported from the site. The effects of the fireball scenario were more significant in comparison to that of the jet fire scenario.     

Effect of pyrolysis and oxidation characteristics on lauric acid and stearic acid dust explosion hazards

The effect of pyrolysis and oxidation characteristics on the explosion sensitivity and severity parameters, including the minimum ignition energy MIE, minimum ignition temperature MIT, minimum explosion concentration MEC, maximum explosion pressure P_max, maximum rate of pressure rise (dP/dt)_max and deflagration index K_st, of lauric acid and stearic acid dust clouds was experimentally investigated. A synchronous thermal analyser was used to test the particle thermal characteristics. The functional test apparatuses including the 1.2 L Hartmann-tube apparatus, modified Godbert-Greenwald furnace, and 20 L explosion apparatus were used to test the explosion parameters. The results indicated that the rapid and slow weight loss processes of lauric acid dust followed a one-dimensional diffusion model (D1 model) and a 1.5 order chemical reaction model (F1.5 model), respectively. In addition, the rapid and slow weight loss processes of stearic acid followed a 1.5 order chemical reaction model (F1.5 model) and a three-dimensional diffusion model (D3 model), respectively, and the corresponding average apparent activation energy E and pre-exponential factor A were larger than those of lauric acid. The stearic acid dust explosion had higher values of MIE and MIT, which were mainly dependent on the higher pyrolysis and oxidation temperatures and the larger apparent activation energy E determining the slower rate of chemical bond breakage during pyrolysis and oxidation. In contrast, the lauric acid dust explosion had a higher MEC related to a smaller pre-exponential factor A with a lower amount of released reaction heat and a lower heat release rate during pyrolysis and oxidation. Additionally, due to the competition regime of the higher oxidation reaction heat release and greater consumption of oxygen during explosion, the explosion pressure P_m of the stearic acid dust was larger in low concentration ranges and decayed to an even smaller pressure than with lauric acid when the concentration exceeded 500 g/m³. The rate of explosion pressure rise (dP/dt)_m of the stearic acid dust was always larger in the experimental concentration range. The stearic acid dust explosion possessed a higher P_max, (dP/dt)_max and K_st mainly because of a larger pre-exponential factor A related to more active sites participating in the pyrolysis and oxidation reaction. Consequently, the active chemical reaction occurred more violently, and the temperature and overpressure rose faster, indicating a higher explosion hazard class for stearic acid dust.     

城区天然气管道泄漏数值模拟与爆炸危害分析

在人口密度为三级和四级的城区内,密集的高建筑物对天然气管道泄漏后的扩散和流场形成产生重要影响。本文以某城市的实际情况为例,建立多建筑物的空间几何模型,采用k-ε湍流方程,SIMPLE算法,模拟了在三种不同风流速度、三种不同压力条件下,城区天然气管道泄漏气体在多建筑物地形中的扩散情况。根据模拟结果,依据天然气的爆炸极限,对模拟结果及其火灾爆炸危害的范围进行了对比分析。结果表明,CH4气体的泄漏扩散同时受管道压力、风流速度和周围建筑物的影响;同时受当地风速的影响,泄漏气柱在风流作用下会发生偏折,造成阻挡风流的建筑物内侧危险气体浓度升高,大大增加建筑物周围环境的危险性。研究结果对城区天然气管道的建设具有一定的指导意义。     

The application of pressure–impulse curves in a blast exceedance analysis

The magnitude of damage due to a vapor cloud explosion can be estimated in many ways, ranging from look-up tables to quantitative risk analysis. An explosion overpressure analysis is a routine part of compliance with the American Petroleum Institute (API) Recommended Practice (RP) 752 when evaluating occupied buildings in a facility that processes flammable or reactive materials. In many cases, a risk-based approach is useful because consequence modeling studies often indicate major problems for buildings at existing facilities. One of the most common risk-based methods, overpressure exceedance, incorporates a wide range of potential explosion scenarios coupled with the probability of each event to develop the probability of exceeding a given overpressure at specific locations. But this and other methods that only use overpressure may not represent an accurate building response. By combining the risk-based methodology of the exceedance analysis with pressure and impulse data in the form of pressure–impulse (P–I) curves, a better measure of building damage can be generated. P–I curves for blast loading determination have been in use for decades, and allow the user to determine levels of damage based on a predicted overpressure and its corresponding impulse. Curves have been published for entire buildings, individual structural members, window breakage, and even consequences to humans. This paper will explore application of P–I curves for building damage, and will highlight some of the benefits, as well as some of the potential problems, of using P–I curves.     

Experimental study on explosion inhibition by heptafluoropropane and its synergy with inert gas

The inhibition effect of heptafluoropropane (CF₃CHFCF₃) on methane explosions under different inhibitor concentrations in a closed vessel was studied. A high-speed camera and a pressure sensor were adopted respectively to record flame propagation characteristics and pressure data. Results indicate that the relationship between flame propagation and pressure rising was correlated. As the equivalent ratio (ϕ)≤1, the pressure presented a trend of rising firstly and then decreasing with increasing CF₃CHFCF₃ concentration, and it was found that there existed a critical concentration for pressure decrease. As ϕ > 1, the pressure exhibited a decreasing trend. Although the pressure appeared to seemingly increase, the moment that the pressure began to rise (t_rise) and the moment that the maximum explosion overpressure appeared (t_Pmax) were obviously delayed. The average rate of pressure rise ((dP/dt)_ave) was decreased as the concentration of CF3CHFCF3 increased. It indicates that CF₃CHFCF₃ can effectively reduce the explosion reaction rate. The critical concentration of CF₃CHFCF₃ for complete inhibition was determined. Meanwhile, the synergy of CF₃CHFCF₃-inert gas can improve the inhibition effect. Compared with CF₃CHFCF₃–N₂, the synergy of CF₃CHFCF₃–CO₂ presented a better inhibition effect, and the inhibition effect was increased with increasing inert gas concentration. And the mechanisms of physical and chemical effects on explosion inhibition were analyzed.