4种典型易燃烟煤的着火特性分析*

为了研究典型易燃烟煤的着火特性,预防和控制煤尘爆炸,采用粉尘云最低着火温度实验装置和同步热分析仪,分别研究崔木长焰煤、东荣二矿气煤、察哈素不粘煤和丁集焦煤4种烟煤在不同条件下的煤尘云最低着火温度和煤尘热解过程。研究结果表明:当煤尘云浓度从0.90 kg/m3上升到5.99 kg/m3时,4种煤尘的最低着火温度先降后升,在1.50 kg/m3煤尘云浓度时,4种煤尘的最低着火温度均达到最小,分别为450,580,610,620 ℃。随着升温速率的升高,煤的着火温度、峰值温度、燃尽温度和煤样最大放热量整体呈上升趋势,失重率整体呈下降趋势,在5~20 ℃/min的升温速率范围内,崔木长焰煤、东荣二矿气煤、察哈素不粘煤和丁集焦煤热解过程中的最小着火温度分别为354.17,404.37,443.18,484.13 ℃。4种烟煤的最低着火温度和热解过程中的最小着火温度有相对应关系,研究结论可为以上4个煤矿的具体煤样研究和数据分析提供参考依据。     

Nex-Hys: minimum ignition temperature of hybrid mixtures

Although the minimum ignition temperature is an important safety characteristic and of practical relevance in industrial processes, actually only standard operation procedures are available for pure substances and single-phase values. Nevertheless, combinations of substances or mixtures are used in industrial processes and up to now it is not possible to provide a standardised minimum ignition temperature and in consequence to design a process safely with regard to the substances used.In order to get minimum ignition temperatures for frequently used hybrid mixtures, first, the minimum ignition temperatures and ignition frequencies were determined in the modified Godbert-Greenwald furnace for two single phase solids and a liquid substance. Second, minimum ignition temperatures and ignition frequencies were determined for several combinations as hybrid mixture of dust and liquid.In parallel to the determination of ignition temperatures a new camera and computer system to differentiate ignition from non-ignition is developed. First results are promising that such a system could be much less operator depended.By a high number of repetitions to classify regions of ignition the base is laid to decide about a new procedure for a hybrid standard and updating existing ones, too. This is one of the necessary aims to be reached in the Nex-Hys project.A noticeable decrease of minimum ignition temperatures below the MIT of the pure solids was observed for the one hybrid mixture tested, yet. Furthermore more widely dispersed area of ignition is shown. In accordance to previously findings, the results demonstrate a strong relationship between likelihood of explosion and amount of added solvent. In consequence the hybrid mixture is characterized by a lower minimum ignition temperature than the single dust.     

A numerical model for the prediction of the minimum ignition temperature of dust clouds

This paper presents a numerical model for the prediction of the minimum ignition temperature (MIT) of dust clouds. First, a physical model is developed for the dust cloud ignition in the Godbert-Greenwald furnace. A numerical approach is then applied for the MIT prediction based on the physical model. The model considers heat transfer between the air and dust particles, the dust particle reaction kinetics, and the residence times of dust clouds in the furnace. In general, for the 13 dusts studied, the calculated MIT data are in agreement with the experimental values. There is also great accordance between the experimental and numerical MIT variation trends against particle size. Two different ignition modes are discovered. The first one consists in ignition near the furnace wall for bigger particles characterized by rather short residence times. In the second mode, the ignition starts from the center of the furnace by self-heating of the dust cloud for smaller particles with longer residence times. For magnesium, as dust concentration increases, the lowest ignition temperature of the dust cloud IT(conc) decreases first, then transits to increase at a certain point. The transition happens at different dust concentrations for different particle sizes. Moreover, the MIT of the magnesium dust cloud generally increases as particle size increases, but the increasing trend stagnates within a certain medium particle size range.     

超细三七粉最小引燃温度实验研究

为研究三七粉着火燃烧的参数,用粉尘云引燃温度装置和粉尘层引燃温度装置,对三七粉的最小引燃温度(MIT)进行实验研究。分别研究喷吹压力、质量浓度、粉尘层厚度对MIT的影响。结果表明:三七粉尘云的质量在0.2 g时最小引燃温度随着喷尘压力的增加先减小再增大,在0.3 g到0.6 g时最小引燃温度随着喷尘压力的增加而增大;在压力20 kPa、30 kPa时随着质量浓度的增大,粉尘云引燃温度先减小后增大,在40 kPa到60 kPa时,随着质量浓度的增大,粉尘云引燃温度增大;粉尘云最小引燃温度高于粉尘层最小引燃温度;三七粉尘云的最小引燃温度399℃,粉尘层最小引燃温度240℃。     

Influence of coal particles on methane/air mixture ignition in a heated environment

The temperature at which coal dust glows is normally much lower than the auto-ignition temperature (AIT) of methane/air mixtures, and thus a better understanding is needed regarding methane/air ignition in a heated environment in the presence of coal particles. A horizontal tube apparatus was used to test the effect of brown coal and two kinds of bituminous and anthracite on methane/air combustibility. For the four coal samples tested, the presence of coal particles significantly reduced the minimum temperature for ignition of methane/air mixtures in a heated environment. No. 1 bituminous coal with 12 mm diameter decreased the ignition temperature value from 595 to 500 °C. It is thought that pre-ignition of low-AIT volatiles emitted from the heated coal particles ignited the methane/air mixtures. Volatiles, sulfur content, and large porosity of piled coal particles all enhanced ignition of methane/air mixtures in a hot environment, while water content and small particle size reduced ignition. For anthracite, no ignition occurred when temperatures of the heated environment were lower than the AIT of methane (595 °C), except for the 12-mm-diameter sample. Anthracite did not readily ignite methane/air mixtures and the ignition mechanism was somewhat similar to that of a burning cigarette.     

Safe handling of combustible powders during transportation,charging, discharging and storage

The knowledge of the ignition behavior of dust–air mixtures due to electrical sparks (MIE, Minimum Ignition Energy) and hot surfaces (MIT, Minimum Ignition Temperature) is important for risk assessments in chemical production plants. The ignition behavior determines the extent and hence the cost of preventive protection measures.This paper describes the use of the minimum ignition energy and minimum ignition temperature as very important safety indexes in practice.     

Inhibiting effect of inhibitors on ignition sensitivity of wood dust

Wood products are easy to produce dust in the production and processing process, and have a serious explosion risk. In order to improve the safety of wood products production, the inhibiting effects of magnesium hydroxide (MTH), SiO₂, melamine polyphosphate (MPP) on the minimum ignition energy (MIE) and minimum ignition temperature (MIT) of wood dust were experimentally studied. The results showed that the inhibiting effects of inhibitors on the MIE of wood dust show the order of MPP > SiO₂>MTH. The order of the inhibiting effects on the MIT of wood dust was MPP > MTH > SiO_2. When 10% MPP was added to wood dust, the time when the flame appears (T_appear) and the time when the flame reaches the top of the glass tube (T_top) obviously rose to 80, 140 ms. Therefore, MPP had the best inhibiting effect on the ignition sensitivity of wood dust.According to thermogravimetry (TG), differential scanning calorimetry (DSC) tests, the introduction of MPP leaded to lower maximum mass loss rate (MMLR), higher temperature corresponding to mass loss of 90% (T_0.1), residual mass and heat absorption. In addition, thermogravimetric analysis/infrared spectrometry (TG-IR) results showed that MPP produced H₂O (g) and NH₃ (g) during the thermal decomposition process, which diluted the oxygen.     

不同挥发分煤尘层最低着火温度变化规律研究

针对煤化工等行业的沉积煤尘热自燃问题,运用煤尘层最低着火温度测试系统,研究了不同挥发分煤尘层的着火状态、不同挥发分及不同厚度煤尘层最低着火温度的变化规律。结果表明:煤尘层厚度为5 mm时,挥发分质量分数大于35%的煤尘在较低温度便出现着火现象,肉眼很容易观察到火星的出现,温度曲线波动剧烈,而对于挥发分质量分数小于15%的煤尘,通过煤尘层内部"温度达到450℃"来判断其着火;在灰分质量分数相当的情况下,煤尘层最低着火温度随挥发分增加呈严格递减的趋势变化;得到了煤尘层厚度和最低着火温度的函数关系式,通过试验得到了挥发分质量分数为37.45%煤尘的重要常数M和N。     

Methane/coal dust/air explosions and their suppression by solid particle suppressing agents in a large-scale experimental tube

Methane/coal dust/air explosions under strong ignition conditions have been studied in a 199 mm inner diameter and 30.8 m long horizontal tube. A fuel gas/air manifold assembly was used to introduce methane and air into the experimental tube, and an array of 44 equally spaced dust dispersion units was used to disperse coal dust particles into the tube. The methane/coal dust/air mixture was ignited by a 7 m long epoxypropane mist cloud explosion. A deflagration-to-detonation transition (DDT) was observed, and a self-sustained detonation wave characterized by the existence of a transverse wave was propagated in the methane/coal dust/air mixtures.The suppressing effects on methane/coal dust/air mixture explosions of three solid particle suppressing agents have been studied. Coal dust and the suppressing agent were injected into the experimental tube by the dust dispersion units. The length of the suppression was 14 m. The suppression agents examined in this study comprised ABC powder, SiO₂ powder, and rock dust powder (CaCO₃). Methane/coal dust/air explosions can be efficiently suppressed by the suppression agents characterized by the rapid decrease in overpressure and propagating velocity of the explosion waves.     

Smoldering combustion of dust layer on hot surface

The critical temperature as well as the critical flux for ignition of a dust layer of cornflour and a mixture of wheatflour and cornflour (80% wheatflour+20% cornflour) on a hot plate have been determined. The moulded sample was cylindrical in shape and of different heights and diameters. The particle size of dusts ranged between 63 μm to 150 μm. The temperature–time histories for self-heating without ignition and with ignition are offered, showing the critical boundaries between them. Also the times to ignition for each dust, showing the effect of sample size on their values, are determined. Certain experimental correlations which relate to times to ignition, as well as the critical temperature for ignition and thermal and geometrical dimensions of sample are presented.     

煤油共生矿区含油煤尘云最低着火温度试验研究

为研究煤油共生矿区含油煤尘最低着火温度的变化规律,选取3种含油浓度不同的煤样,采用粉尘云最低着火温度测定系统,研究含油煤尘云最低着火温度随含油浓度、喷尘压力及煤尘质量的变化规律。研究结果表明:含油煤尘的最低着火温度较不含油煤尘显著降低,且随着煤尘含油浓度的增加,煤尘中挥发分含量增多,煤尘云最低着火温度降低,爆炸危险性增强;低含油浓度煤尘,煤尘受原油挥发分影响较大,在含油浓度为5.7%,4.3%且质量浓度为1364~4550 g/m3时煤尘云最低着火温度随喷尘压力的增大呈先增大后减小的变化趋势,在5.7%,4.3%含油浓度且喷尘压力为0.05 MPa时煤尘MIT随煤尘质量浓度增加先降低后缓慢升高。高含油浓度煤尘,受煤尘团聚现象影响较大,煤尘云最低着火温度随喷尘压力的增加而升高,随煤尘质量的增加呈先减小后增大再缓慢减小的变化规律。     

瓦斯对煤尘爆炸特性影响的实验研究

瓦斯的存在对煤尘爆炸特性的理论计算和数值仿真的结果与实际数据有一定差距,因此,通过不同浓度瓦斯与煤尘共存条件下爆炸实验研究,得出了矿井瓦斯对煤尘的最低着火温度、最小点火能量、爆炸下限浓度、最大爆炸压力和最大爆炸压力上升速度等爆炸特性影响的规律即瓦斯对煤尘最低着火温度影响不大;瓦斯可使煤尘的最小点火能量减小,尤其是对难于点燃的煤尘;混合物的爆炸下限浓度随瓦斯浓度的增加而降低;混合物的最大爆炸压力上升速度由于瓦斯的存在而增强,而最大爆炸压力几乎没有变化。同时研究了瓦斯对无爆炸性煤尘的影响。实验研究的结论对于现场防止煤尘爆炸的发生具有指导意义。     

Ignition tests for electrical and mechanical equipment subjected to hot surfaces

This paper reports some experimental work on hot surface ignition temperatures of dust deposits. Dust layers up to 75 mm in depth were ignited using a modified version of the standard 5 mm layer apparatus. The measured ignition temperatures show good agreement with predictions using the method given in EN 50281-2-1. Ignition temperatures of conical dust deposits over an electrically heated box were not predictable, but were not too dissimilar from the ignition temperatures of the thick layers. Both tests gave adequate reproducibility in round robin tests. Rotating steel wheels in contact, immersed in a dust deposit produce the frictional hot surfaces. A relation between the power lost by friction and the surface temperature developed has been derived. The surface temperatures leading to ignition were close to the ignition temperatures for the conical deposits on the heated box. The similarities between the ignition temperatures of dust deposits in several configurations indicate that a simple test for ignition temperature measurement could have wide application in dusty environments.     

燃烧管中烟煤粉粉尘云传播参数的试验研究

利用自行设计的长29.6 m,内径199 mm,配有特殊扬尘装置的大犁卧式燃烧爆炸管道试验系统,对弱点火条件下烟煤粉与空气两相悬浮流中的爆炸过程进行了试验研究,用压电传感器测量了管内各测点的压力信号,观测到快速爆燃的状态稳定,分析了爆燃波稳定传播机理.结果表明:在煤粉浓度为300g/m~3及弱点火条件下,悬浮烟煤粉粉尘云中爆燃波能够稳定传播,且稳态传播距离持续20 m以上,峰值超压和波速平均值分别约为70 kPa和430m/s.     

Explosibility of micron- and nano-size titanium powders

Explosibility of micron- and nano-titanium was determined and compared according to explosion severity and likelihood using standard dust explosion equipment. ASTM methods were followed using a Siwek 20-L explosion chamber, MIKE 3 apparatus and BAM oven. The explosibility parameters investigated for both size ranges of titanium include explosion severity (maximum explosion pressure (P_max) and size-normalized maximum rate of pressure rise (K_St)) and explosion likelihood (minimum explosible concentration (MEC), minimum ignition energy (MIE) and minimum ignition temperature (MIT)). Titanium particle sizes were ?100 mesh (<150 μm), ?325 mesh (<45 μm), ≤20 μm, 150 nm, 60–80 nm, and 40–60 nm. The results show a significant increase in explosion severity as the particle size decreases from ?100 mesh with an apparent plateau being reached at ?325 mesh and ≤20 μm. Micron-size explosion severity could not be compared with that for nano-titanium due to pre-ignition of the nano-powder in the 20-L chamber. The likelihood of an explosion increases significantly as the particle size decreases into the nano range. Nano-titanium is very sensitive and can self-ignite under the appropriate conditions. The explosive properties of the nano-titanium can be suppressed by adding nano-titanium dioxide to the dust mixture. Safety precautions and procedures for the nano-titanium are also discussed.     

不饱和聚酯树脂钮扣粉尘静电爆炸敏感性研究

针对某不饱和聚酯树脂钮扣厂在除尘设备维修过程中发生的粉尘爆炸事故,探究静电引起此次事故的可能性并提出防护措施。通过实验测定不饱和聚酯树脂钮扣粉尘的爆炸特性参数,进而确定其静电爆炸敏感性。结果发现:不饱和聚酯树脂钮扣粉尘云最小点火能MIE为4～10 mJ、最低着火温度MIT为480 ℃、粉尘层最低着火温度LIT＞400 ℃。表明,此粉尘属易燃粉尘,其粉尘爆炸敏感度极高,被静电火花点燃的可能性极大,在生产过程中,应采取静电防护措施。     

Influence of different ignition delay times on the pressure rise rate in hybrid mixture explosions in the 20-L sphere

For the development of a standardized method for measuring the explosion safety characteristics of combustible hybrid dust/vapor mixtures, the influence of the ignition delay time needs to be investigated. The ignition delay time, defined as the time between the injection of dust and the activation of the ignition source, is related to the turbulence of the mixture and thus to the pressure rise rate. The ignition source for pure vapors, however, has to be activated in a quiescent atmosphere according to the standards. Nevertheless, when measuring the explosion safety characteristics of hybrid mixtures, it is important that the dust be in suspension around the igniter. Like pure dust/air mixtures, hybrid dust/vapor/air mixtures need to be ignited in a turbulent atmosphere to keep the dust in suspension.This work will therefore investigate the influence of ignition delay times on the severity of hybrid explosions. It was generally found that at shorter ignition delay times, (dp/dt)_ex increased due to higher turbulence and decreases as the dust sinks to the bottom of the 20 L-sphere. This effect is more pronounced for hybrid mixtures with higher vapor content compared to dust content.     

Explosibility parameters for mixtures of pulverized fuel and ash

This paper reports the results of experiments done to examine the explosibility of pulverized fuel dusts (two different coals and petroleum coke) and their waste products (bottom and fly ashes). Tests were conducted for the fuel dusts alone and also blended with other fuels and ashes. The explosion parameters of interest were maximum pressure and rate of pressure rise, and ignition energy and temperature. Petroleum coke was found to present a lesser explosion hazard than the coals. Admixture of either coal or petroleum coke with fly ash resulted in explosible mixtures at volatile contents dependent on the composition of the mixture components and their particle sizes.     

Effect of particle size and dust layer size on ignition characteristics of PMMA dust layer on hot surface

Deposition of combustible dust on a hot surface is a hidden danger of fire. In this work, polymethylmethacrylate (PMMA) dust was selected to analyse the influence of dust layer diameter, dust particle size and dust layer thickness on the ignition characteristics of PMMA dust layer. Critical heating temperatures and ignition time had been measured. The STA-GC/MS-FTIR analysis was used to determine that the main products of PMMA pyrolysis were MMA, CO, CO₂, and C₂H₄, of which CO and C₂H₄ were transported to the ambient to cause gas phase combustion on the surface of the dust layer. For 10 mm thick dust layer, the critical heating temperatures of 5 μm PMMA, 100 nm PMMA, and 30 μm PMMA were 300 °C, 330 °C, and 320 °C. As the thickness of the dust layer increased, the gas transport path became longer, the critical heating temperature and ignition time increased. The characteristic particle size (D [3,2]) was utilized to represent the true particle size, and the ignition time increased with the increase of the characteristic particle size. The increase in the diameter of the dust layer had a slight effect on the temperature history and ignition time of the dust layer.     

煤岩混合型粉尘云最低着火温度试验研究

为研究半煤岩巷道中岩粉质量分数和煤的挥发分与煤岩混合型粉尘云最低着火温度的关系,选取挥发分差异较大的5种煤样以相同比例配制煤岩混合型粉尘,利用粉尘云最小点火温度测定仪进行煤岩混合型粉尘试验。结果表明,当煤岩混合型粉尘中岩粉质量分数低于40%时,岩粉的混合会导致混合型粉尘云最低着火温度发生小幅度波动;当岩粉质量分数高于40%时,煤岩混合型粉尘最低着火温度会随岩粉质量分数的增加而大幅度升高;挥发分质量分数越小的煤粉,其混合型粉尘云最低着火温度越容易受岩粉质量分数的影响。