Utilization of the solid sorbent media in monitoring of airborne cyclophosphamide concentrations and the implications for occupational hygiene

The main objective of the study was to evaluate the applicability of two solid sorbent media (Anasorb 708 and Strata X), the impinger filled with distilled water and PTFE filters for determination of airborne cyclophosphamide (CP) in the hospital working environment. For this purpose, air contamination of Masaryk Memorial Cancer Institute (Czech Republic) was monitored using the sampling apparatus containing the samplers described above. In addition, the surface contamination was also determined using the wipe sampling technique. During the monitoring, contamination of three different workplaces (storage room, preparation room and outpatient clinic) was studied. Using Strata X solid sorbent tubes, airborne CP was determined in all (n = 5) samples collected at the outpatient clinic over a 5 day monitoring period (concentration range: 0.3-4.3 ng m(-3)). Other samplers (including PTFE filters) did not collect any detectable amount of CP (the limit of detection, LOD ≤ 0.1 ng m(-3)). Negative results detected at filter samples indicate that CP determined at Strata X samples was most probably of gaseous origin. Surface contamination ranged from <2 to 19, <8 to 418 and 133-15,500 pg cm(-2) at the storage room, preparation room and outpatient clinic, respectively. The study showed that evaporation of antineoplastic drugs should not be neglected, albeit the concentrations determined in our study are relatively low. Therefore, proper monitoring of airborne contamination should involve simultaneous sampling of both particle-bonded and gaseous phases. In this way, Strata X sorbent tubes seem to be an effective tool for the sampling of gaseous CP in the indoor air.     

Dermal Insecticide Residues from Birds Inhabiting an Orchard

The US Environmental Protection Agency conducts risk assessments of insecticide applications to wild birds using a model that is limited to the dietary route of exposure. However, free-flying birds are also exposed to insecticides via the inhalation and dermal routes. We measured azinphos-methyl residues on the skin plus feathers and the feet of brown-headed cowbirds (Molothrus ater) in order to quantify dermal exposure to songbirds that entered and inhabited an apple (Malus x domestica) orchard following an insecticide application. Exposure to azinphos-methyl was measured by sampling birds from an aviary that was built around an apple tree. Birds sampled at 36 h and 7-day post-application were placed in the aviary within 1 h after the application whereas birds exposed for 3 days were released into the aviary 4-day post-application. Residues on vegetation and soil were also measured. Azinphos-methyl residues were detected from the skin plus feathers and the feet from all exposure periods. Our results underscore the importance of incorporating dermal exposure into avian pesticide risk assessments.     

Monitoring and assessment of airborne fungi in Kolkata, India, by viable and non-viable air sampling methods

The composition and variability of airborne fungal spores were studied using two complementary sampling methods in an outdoor environment in Kolkata suburb for 2 years, from November 2002 to October 2004. For monitoring the total fungal spore burden in the air, Burkard 7-day volumetric sampler was used, whereas Andersen two-sage viable sampler was used for isolating the cultivable airborne fungi. Among the 37 fungal spore types identified in the air samples, the predominant ones were Cladosporium, unidentified ascospores, unidentified basidiospores, Aspergilli/Penicilli, Nigrospora, Periconia, Chaetomium, Drechslera, Alternaria, Coprinus, Ganoderma, Pithomyces, and rust spores. Only six fungal spore types (Alternaria, Aspergilli/Penicilli, Cladosporium, Curvularia, Drechslera, and Nigrospora) were recovered in common by the two samplers. For Aspergilli/Penicilli, Drechslera, and Nigrospora, the spore concentration was underestimated in the non-viable sampling method (Burkard sampler). In general, higher spore count was recorded in winter. The highest fungal species variability was observed in early monsoon (June). Relative humidity could significantly predict the seasonal periodicity of the maximum number of airborne spores. The total airborne fungi concentration recorded in the study (15-16?×?10(3) spores m(-3) of air) was lower than the proposed threshold limit value for clinical significance, suggesting apparently no or less airborne-fungi-exposure-related health risk in the sampling area. Cladosporium cladosporioides was recorded beyond the proposed threshold limit value in January 2003 and March 2004; Aspergillus fumigatus and Aspergillus nidulans in winter that might have posed considerable health risk to sensitized individuals.     

Vacuum sampling techniques for industrial hygienists, with emphasis on beryllium dust sampling

The U.S. Department of Energy (DOE) Chronic Beryllium Disease Prevention Program Rule, 10 CFR Part 850 became effective in 2000 in response to the prevalence of Chronic Beryllium Disease (CBD) in workers. The rule requires surface and air monitoring for beryllium to determine exposure levels and the evaluation of the effectiveness of controls used to minimize or eliminate that risk. The most common methods for surface sampling use wet or dry wipes. Wipe sampling techniques may be impractical for many surfaces common to most buildings such as cinder block, textured wall surfaces, fabric and carpet. Vacuum sampling methods have been developed for the evaluation of lead or pesticides on residential surfaces such as carpets, bare floors and window sills. However, the current vacuum methods may be impractical for many workplace situations such as sampling of protective clothing, complex facility structures, or equipment surfaces. Recent work using vacuum sampling for potential bio-terrorism agents such as anthrax spores may have significant application to industrial hygiene evaluations of the workplace and may be extendable for use in sampling of metals such as beryllium. Validated vacuum sampling methods that provide meaningful data would be of great value to industrial hygienists in identifying areas having surface contamination, evaluating existing controls and work practices and determining the potential of toxic material on surfaces to become airborne and present a potential risk to workers and the public. This article discusses various vacuum sampling methodologies and recommends harmonization of sampling methods.     

Documentation of bioaerosol concentrations in an indoor composting facility in France

Bioaerosol concentrations were investigated in a totally indoor composting facility processing fermentable household and green wastes to assess their variability. Stationary samples were collected by filtration close to specific composting operations and then were analysed for cultivable mesophilic bacteria, thermophilic bacteria, mesophilic fungi, thermophilic fungi, endotoxins and total airborne bacteria (DAPI-staining). Indoor concentrations exceeded the background levels, between 500 and 5400 EU m(-3) for endotoxins, 10(4) and 10(6) CFU m(-3) for cultivable bacteria and generally below 10(5) CFU m(-3) for airborne cultivable fungi. No significant (p > 0.05) differences were observed between the indoor composting operations. Successive 30 minute bioaerosol samples were collected to investigate the variation of cultivable mesophilic microorganisms over the work shift. Concentrations of mesophilic bacteria and fungi varied up to 1 log unit depending on the time at which they were collected in the day. Total airborne particles, counted using an optical particle counter, were present at up to 10(8) particles m(-3) and several concentration peaks were noted. Values for total airborne bacteria were roughly 70-fold higher than cultivable bacteria. These results raise the question of the sampling strategy (duration of sampling; number of samples to be collected) used in similar studies. They provide new bioaerosol concentration data in a composting facility and suggest that the filtration sampling method might be a useful tool for exposure measurements in that occupational environment.     

Assessment of workers' exposure to palladium in a catalyst production plant

Airborne particulate matter was collected and biomonitoring of workers was performed by sampling blood, urine and hair of 84 exposed subjects, 17 occasionally exposed employees, 21 controls from administrative offices and 25 unexposed people (external controls). Determination of Pd was performed using Quadrupole and High Resolution Inductively Coupled Plasma Mass Spectrometry. The Production of Catalysts Department and the Refining Service presented the highest levels of Pd in airborne matter collected by means of an area sampler. The highest level of soluble Pd (1.66 microg m(-3)) was found in the Production of Catalysts Department. The highest concentration of Pd in airborne matter, collected by means of personal devices (7.90 microg m(-3)) was found in the Refining Service. Hair showed a clear distribution pattern among departments, with values ranging from 0.60 to 5.54 microg g(-1). Administrative workers presented blood levels of Pd between 2 and 500 times higher than external controls. Only urine levels correlated with the measurements of airborne Pd collected with personal devices. A very strong association between airborne Pd collected by personal devices and Pd levels in hair (r(2)= 0.569, with p< or = 0.01) and urine (r(2)= 0.684, with p< or = 0.01) was found. On the basis of these findings: (i) blood results appear to be an unsuitable biological marker for occupational exposure to Pd; (ii) urine could be considered as a satisfactorily responsive bio-marker for occupational monitoring; and (iii) hair cannot be considered a good index of time-related exposure.     

DDVP residues in air following application to a tobacco-storage warehouse

A 10% solution of DDVP was sprayed until a total volume of 20.9 liters of the solution had been released into the air in a tobacco-storage warehouse. Air samples were taken at various times after application in three different experiments to measure DDVP levels with time and to determine if DDVP concentrations exceeded the threshold limit (TVL). In the three experiments, residue levels were highest initially in the center of the warehouse compared to a corner, but residue levels tended to equalize over the sampling period. The data indicated that workers entering storage warehouses after application of DDVP would not encounter hazardous levels of this material.     

Monitoring of glyphosate and AMPA in soil samples from two olive cultivation areas in Greece: aspects related to spray operators activities

The persistence of glyphosate and its primary metabolite AMPA (aminomethylphosphonic acid) was monitored in two areas in Southern Greece (Peza, Crete and Chora Trifilias, Peloponnese) with a known history of glyphosate use, and the levels of residues were linked to spray operators’ activities in the respective areas. A total of 170 samples were collected and analysed from both areas during a 3-year monitoring study. A new method (Impact Assessment Procedure - IAP) designed to assess potential impacts to the environment caused by growers’ activities, was utilised in the explanation of the results. The level of residues was compared to the predicted environmental concentrations in soil. The ratio of the measured concentrations to the predicted environmental concentrations (MCs/PECs) was >?1 in Chora the first 2 years of sampling and <?1 in the third year, whilst the MCs/PECs ratio was <?1 in Peza, throughout the whole monitoring period. The compliance to the instructions for best handling practices, which operators received during the monitoring period, was reflected in the amount of residues and the MCs/PECs ratio in the second and especially the third sampling year. Differences in the level of residues between areas as well as sampling sites of the same area were identified. AMPA persisted longer than the parent compound glyphosate in both areas.     

Diffusive Sampling of VOCs as an Aid to Monitoring Urban Air Quality

Diffusive sampling of Volatile Organic Compounds (VOCs) onto thermal desorption tubes, followed by gas chromatography, is an established technique for area or personal monitoring of typical workplace concentrations and there has been increasing interest in extending the application to environmental levels, particularly for benzene, toluene and xylene (BTX). Diffusive sampling rates for BTX on Chromosorb 106 and Carbograph-1 (a graphitised carbon) were measured over periods of 1-4 weeks in field validation experiments using ambient air and parallel pumped sampling (the reference method) at the HSL site in central Sheffield. The reference method was also used to investigate the possible bias of an open-path spectrophotometer (OPSIS) used by Sheffield City Council. A bias for BTX was suspected from results of a two-week initial exercise in which several diffusive samplers were placed close to the light path. In the full field validation of the diffusive samplers carried out subsequently, the significant bias of BTX concentrations reported by OPSIS were confirmed when compared with concurrent results from the reference method. OPSIS gave benzene and toluene values up to eight times higher than expected from the GC measurements. Xylene discrepancies were smaller, but in one 3-day peak episode, OPSIS demonstrated a negative correlation with GC.     

South Florida Water Management District ambient pesticide monitoring network: 1992 to 2007

The South Florida Water Management District has collected surface water and sediment samples for analysis of over 80 pesticides since 1992. Residues of atrazine and DDE-p,p(') are nearly ubiquitous throughout the sampling area. Surface water concentrations of atrazine at nine of 14 selected monitoring locations exhibited a downward trend and none of the detected concentrations exceeded established levels of concern. Seventy-five percent of the sampled locations had average sediment residues of DDE-p,p(') at levels that may impact sediment-dwelling organisms. Monitoring locations with the highest average DDE-p,p(') concentrations (based on detected values) and the highest percentage of pesticide detections did not exhibit consistent trends. Some locations exhibited increasing trends while trends at other locations showed a decrease in concentrations. Additionally, specific location concentrations for ethion, diazinon, and endosulfan documented periods of surface water quality exceedances. However, product label changes and grower education have substantially contributed to the reduced number of exceedances over time.     

Continuous, intermittent and passive sampling of airborne VOCs

Long sampling periods are often advantageous or required for measuring air quality and characterizing exposures. However, sampling periods exceeding 8 to 24 h using thermally desorbable adsorbent tube (TDT) samplers for the measurement of airborne volatile organic compounds (VOCs) face several challenges, including maintaining stable and low flow rates, and avoiding breakthrough of the adsorbent. These problems may be avoided using intermittent sampling; however, the literature contains few if any reports that have evaluated this technique in environmental, occupational or other applications. The purpose of this study is to evaluate continuous, intermittent and passive sampling methods using both laboratory and real-world tests. Laboratory tests compared continuous and intermittent (active) samplers in a controlled dynamic test gas generation system. Field tests used side-by-side active and passive samplers in an office, home workshop and four smokers' homes. All samples were analyzed for a wide range of VOCs by GC-MS. In most instances, intermittent sampling yielded better reproducibility (duplicate precision of 10 +/- 6%) than continuous low-flow sampling (18 +/- 5%), in part due to difficulty maintaining low flows. Concentrations obtained using intermittent sampling agreed with those for continuous sampling, with downward biases resulting primarily from errors in flow rate measurements. In the field, more VOC species were detected using active rather than passive sampling. Passive measurements were 12% lower than continuous measurements, a difference attributed to declining uptake rates at higher concentrations over the 3 to 4 d sampling period. Overall, most measurements obtained using the three sampling methods agreed within 20% for a wide range of concentrations (0.1 to 230 microg m(-3)). Both passive and intermittent sampling approaches are suitable for long sampling periods, but intermittent sampling provides greater flexibility with respect to sampling period, and permits the use of multi-bed adsorbents that can capture a wider range of VOCs.     

Air pollution impact assessment on agroecosystem and human health characterisation in the area surrounding the industrial settlement of Milazzo (Italy): a multidisciplinary approach

In order to evaluate the impact of atmospheric pollutants emitted by the industrial settlement of Milazzo (Italy) on agriculture, sulphur dioxide and ozone levels in air were monitored and the data were used to estimate yield losses of the most widespread cultures. Trace element concentrations in crops and soils were also detected and metabolic profiles of soil microbial communities were considered. Vibrio fischeri test was used to appraise airborne pollutant ecotoxicity and epidemiological studies on causes of death distribution were carried out to characterize health state of people living in the area. All the sampling points were selected in farms on the basis of a theoretical meteo-diffusive model of industrial air pollutants. Experimental SO₂ and O₃ values mainly exceeded the threshold established by Italian and EU regulations to protect vegetation and they correspond to estimated significant crop losses. Conversely toxic element residues in soils and in agroalimentary products were generally lower than the fixed values. SO₂ and O₃ concentrations, toxic element contents and ecotoxicity levels of airborne pollutants were not related only to industrial site emissions, while the fluctuations on metabolic profiles of soil microbial communities seem to agree with the predicted deposition of xenobiotic compounds from the industrial plants. The epidemiological study evidenced a better health state of populations living in the investigated area than in the Messina province and the Sicily region but, inside the area, males living in the municipalities closest to the industrial settlement exhibited a worst health state than those in the very far ones.     

Indoor pesticide application practices and levels in homes of Bangkok Metropolitan Region

This study investigated the indoor application practices of pesticides in different homes located in urban, suburban, and rural areas of the Bangkok Metropolitan Region (BMR). A multi-stage stratified-judgmental sampling was applied to select 280 representative households in BMR for an in-depth questionnaire survey. We found about 71% of these households having mosquitoes as their main indoor nuisance. An inventory on the types and active ingredients was obtained through a shop-shelf survey. Among 22 available commercial products, 12 different active ingredients were observed with the pyrethroid containing pesticides are the most common. The stepwise regression analysis was conducted to reveal the statistical association between indoor levels of total pyrethriods (in the air and on the floor surface of homes) and the household application practices such as the overlap time period since the last application, application and storage locations, and frequency of applications, for instances.     

Weekly variation of atmospheric particle micromorphology and chemistry in Brussels urban environment

The purpose of this study was to measure the impact of urban activities on airborne particle dynamics during weekend periods in Brussels urban area. Differences in the granulometry and micromorphology between particles sampled on working days and weekends were studied. We quantified the area, size, number, and the chemistry parameters of the airborne particles and compared between Saturday, Sunday, and Monday. We report and analyze data on airborne particles up to PM10, measured in the Brussels region from October 2002 to September 2003. Our investigation reveals detailed information regarding chemical composition of the airborne particles over the weekend period in the Brussels urban area. Furthermore, the majority of the airborne particles in the Brussels region may belong to sources geographically outside the (in situ) Brussels area.     

Airborne pollen of allergenic herb species in Toledo (Spain)

This study analysed airborne pollen counts for allergenic herb taxa in Toledo (central Spain), a major tourist city receiving over 2 million visitors per year, located in the region of Castilla-La Mancha. The taxa selected were Chenopodiaceae–Amaranthaceae, Plantago, Poaceae and Urticaceae, all of which produce allergenic pollen giving rise to serious symptoms in pollen-allergy sufferers. Aerobiological data were recorded over a 6-year period (2005 to 2010) using the sampling and analysis procedures recommended by the Spanish Aerobiology Network. The abundance and the temporal (annual, daily and intradiurnal) distribution of these pollen types were analysed, and the influence of weather-related factors on airborne pollen counts was assessed. Pollen from herbaceous species accounted for 20.9% of total airborne pollen in Toledo, the largest contributor being Poaceae, with 8.5% of the total pollen count; this family was also the leading cause of respiratory allergies. Examination of intradiurnal variation revealed three distinct distribution patterns: (1) peak daily counts for Chenopodiaceae–Amaranthaceae and Plantago were recorded during the hottest part of the day, i.e. from 1400 to 1600 hours; (2) Urticaceae displayed two peaks (1400–1600 and 2200 hours); and (3) Poaceae counts remained fairly stable throughout the day. Two main risk periods were identified for allergies: spring, with allergies caused by Urticaceae, Plantago and Poaceae pollen, and summer, due to Chenopodiaceae–Amaranthaceae pollen.     

Identification of Residues of Sulfosulfuron and its Metabolites in Subsoil-dissipation Kinetics and Factors Influencing the Stability and Degradation of Residues from Topsoil to Subsoil Under Predominant Cropping Conditions

Long term stability of sulfosulfuron was investigated in subsoil under the natural wheat cropping conditions. Experiments were conducted by applying a commercial formulation of sulfosulfuron on soil at 50 g/ha and 100 g/ha. To understand the factors influencing the persistence of residues two different experiments were conducted. In one experiment wheat crop was cultivated once at the beginning of the two years study period and subsequently the plots were kept undisturbed for the remaining period. In another experiment cultivation of subsequent crops were continued during the study period. In both the cases sulfosulfuron was applied only once at the beginning of the study. Representative soil samples were collected from the depths viz., 0–5, 15, 30, 45, 60 and 90 cm on different pre determined sampling occasions 50, 100, 200, 300, 400, 500 and 600 days after the application of the herbicide. The collected soil samples were analyzed for the residues of sulfosulfuron. Under the influence of continuous cropping conditions residues of sulfosulfuron were found to be relatively low when compared with the soil samples collected from the agriculture plots maintained without any cultivation. The residues detected are in the range 0.001 to 0.017 μg/g. Samples collected from the depth, at 30 to 45 cm showed higher residual concentrations. Soil samples were also showed the presence of break down products. The data has been confirmed by LC–MS/MS. The relation between residue content of sulfosulfuron and the factors contributing the stability of herbicide concentration were also studied.     

Measurement of styrene-7,8-oxide and other oxidation products of styrene in air

Styrene-7,8-oxide (SO) is generated at low concentrations from the oxidation of styrene during the processing of reinforced plastics. Since exposure to SO has important health implications, we developed air sampling and analytical methods to measure low levels of airborne SO in the presence of styrene and its other oxidation products, namely phenylacetaldehyde (PAA) and acetophenone (AP). Both active and passive air monitors were used. The active sampling method, which employed adsorption on Tenax, was suitable for measuring SO, PAA and AP but had limited capacity for styrene due to breakthrough. The passive monitor employed a carbon adsorbent and was suitable for measurement of styrene and SO but not PAA and AP due to poor recovery. After sampling, the analytes were extracted from the adsorbents with ethyl acetate and measured by gas chromatography with flame ionization detection or mass spectrometry. By maintaining the injection port at 70 degrees C, the thermal rearrangement of SO to PAA was minimized. Recovery of styrene and SO from the passive monitor depended upon loading and was corrected by linearization of the Freundlich isotherm. The limits of detection for SO, PAA, and AP were 0.2 ppb using the active monitor, and for SO was 1 ppb using the passive monitor. The sampling precision for SO (RSD from personal measurements) was 5.0% for the passive monitor and was 13.4% for the active monitor over a range of exposures from 5-150 ppb. The corresponding precision for styrene was 5.3% for the passive monitor for levels ranging from 1.2 to 104 ppm. Measurements of 235 personal exposures with the active monitor in 12 facilities manufacturing fiberglass-reinforced plastics (FRP) showed that levels of AP and PAA were below 7.8 ppb and 5 ppb, respectively. In contrast, SO averaged 30.4 ppb (SE=2.4) in these FRP facilities, ranging from below 0.2 ppb to 190 ppb. The active monitor was also used to detect airborne SO at levels of approximately equals 1 ppb in one facility manufacturing styrene butadiene rubber, suggesting that SO is generally present during the polymerization of styrene. Personal passive monitoring in the 12 FRP facilities (n = 657) revealed mean concentrations of styrene ranging between 1.8 and 55.4 ppm, and for SO between 1.7 and 62.6 ppb. The ratio of the mean styrene level to the mean SO level varied between 449:1 and 1,635:1 among the 12 FRP facilities.     

The Contamination Levels of Organochlorine Pesticides in Water and Sediment Samples in Uluabat Lake, Turkey

The Uluabat Lake is a reservoir of 125 km² surface area, in the boundaries of Bursa province, Turkey. The results showed that Uluabat Lake was still contaminated by organochlorine pesticides and their residues despite the existence of bans over a long time. Considerable amounts of organochlorine pesticides (HCB, p.p^′-DDT, p.p^′- DDE, α -, β- and γ-BHC, Aldrin, Heptachlor epoxide, Endrin, Endosulfan I and II) were detected in water and sediment samples during one-year study in this lake. Samples of water and sediment were collected in different regions, (6 sampling point) of the lake between February 2002 and November 2002.The mean levels of organochlorine pesticides in water and sediments were determined. According to results, it was found that various environs in Uluabat Lake were contaminated by 11 different organochlorine pesticides. Residue analyses showed that higher organochlorine pesticides and their residues were generally more accumulated in the sediment samples.     

Intervention study of airborne fungal spora in homes with portable HEPA filtration units

The concentrations and composition of airborne fungal spores in homes fitted with portable HEPA filtration units were examined to provide information to evaluate the importance of varying levels of fungal spores in residential environments in Perth, Australia. A novel method for simulating activity/impaction on carpeted environments was also investigated. Reductions in fungal (35%) and particulate (38%) levels were achieved in the air filter homes. Penicillium, Cladosporium and yeasts were the most common and widespread fungi recovered indoors and outdoors. Fungal range decreased over the study period but this could be due to an overall reduced dissemination of spores (less spores in the air).     

Ambient air concentrations of PCDDs,PCDFs, coplanar PCBs,and PAHs at the Mississippi Sandhill Crane National Wildlife Refuge,Jackson County,Mississippi

Our objective was to determine the levels of selected airborne contaminants in ambient air at the Mississippi Sandhill Crane National Wildlife Refuge, Mississippi, that might be affecting the health of endangered cranes living there. Two high-volume air samplers were operated at separate locations on the Refuge during May–September 1991. The sampling media were micro-quartz filters in combination with polyurethane foam plugs. Composite bimonthly samples from each station were analyzed for polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), coplanar polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs). Overall, residue concentrations were low. The toxic PCDD isomer 2,3,7,8-tetra-CDD was not detected, nor was penta-CDD. There was no difference (P>0.05) in residue concentrations between stations or over time and meteorological parameters were not correlated with residue concentrations. Because contaminant levels and patterns may differ seasonally, we recommend that air samples collected during winter months also be analyzed for these same chemical groups.