酸改性碳材料吸附溶液中U(Ⅵ)

以活性炭、碳纳米管和石墨烯为基体材料,分别采用醋酸、硫酸和硝酸对其进行改性,运用BET、FTIR、SEM等技术对材料进行了表征,详细考察了其对溶液中U(Ⅵ)的吸附性能。实验结果表明：醋酸改性的效果最好,醋酸改性活性炭对U(Ⅵ)的吸附具有更大优势;在吸附时间90 min、吸附剂加入量1.0 g/L、U(Ⅵ)初始质量浓度50 mg/L、醋酸改性活性炭的溶液pH为7、醋酸改性碳纳米管和石墨烯的溶液pH为8的最优吸附条件下,醋酸改性的活性炭、碳纳米管、石墨烯的U(Ⅵ)吸附率分别为90.13%,89.82%,82.08%。表征结果显示：吸附剂对U(Ⅵ)的吸附性能主要取决于其表面羧基、羟基等含氧官能团的数量;吸附剂对U(Ⅵ)的吸附具有化学吸附特征。     

改性木屑吸附处理含Cr(Ⅵ)废水

对改性木屑处理含Cr(Ⅵ)废水进行了研究,考察了溶液Cr(Ⅵ)初始质量浓度、溶液pH、木屑加入量、吸附时间对吸附效果的影响.实验结果表明:在溶液初始Cr(Ⅵ)质量浓度15 mg / L 、溶液pH 2.0、木屑加入量7.5 g / L、吸附时间60 min 的优化实验条件下,硝酸改性木屑比磷酸改性木屑吸附效果好,硝酸改...     

微波改性锆-铝柱撑膨润土对水中Cr(Ⅵ)的吸附

以膨润土为原料,通过微波辐射加热法制备锆-铝柱撑膨润土(MZAPB)吸附剂,研究了 MZAPB 加入量、溶液 pH、吸附时间、温度等因素对 Cr(Ⅵ)吸附效果的影响.研究结果表明:当溶液初始 Cr(Ⅵ)质量浓度为 25mg/L、MZAPB 加入量为 10 g/L、溶液 pH 为 5.6、吸附温度 25℃、吸附时间为 6...     

竹炭对废水中Cu2+的吸附

探讨了竹炭粒径、加入量、溶液 pH、吸附时间、Cu2+初始质量浓度等因素对竹炭吸附 Cu2+效果的影响.实验结果表明:竹炭对废水中Cu2+有很好的吸附效果,当竹炭粒径小于0.15 mm、加入量为 16 g/L、溶液 pH 为 6.0、Cu2+初始质量浓度 25 mg/L、吸附时间为 1.5 h 时,竹炭对 Cu2+的去...     

Cu~(2+)改性活性炭的制备及其去除废水中CN~-的研究

以活性炭为载体负载溶液中的 Cu~(2+),Cu~(2+)改性活性炭对溶液中 CN~-的去除效果较好。Cu~(2+)改性活性炭的最佳制备条件:活性炭加入量为1 g,质量浓度为5 g/L 的 CuSO_4溶液加入量为50 mL,溶液 pH 为4,负载时间为5.0 h。在此最佳条件下活性炭的最大 Cu~(2+)负载量为25.90 mg(以每克活性炭计)。Cu~(2+)改性后活性炭的 CN~-去除率明显提高,由22.10%提高至94.07%。Cu~(2+)改性活性炭吸附CN~-的最佳实验条件:溶液 pH 为12～13,吸附时间为9 h。Cu~(2+)改性活性炭对 CN~-的饱和吸附量为22 mg/g。Mg~(2+),K~+,Ca~(2+),Cl~-,SO_4~(2-),CO_3~(2-),AsO_3~-对 Cu~(2+)改性活性炭的 CN~-去除率基本没有影响。Cu~(2+)改性活性炭的动态吸附实验表明,开始一段时间流出液中 CN~-含量几乎为零,远低于国家排放标准(0.5 mg/L)。     

响应面法优化烧烤竹炭对水中磷的吸附条件

采用响应面法优化烧烤竹炭(BBC)对水中磷的吸附条件。用Box-Behnken Design实验设计考察初始磷质量浓度、BBC粒径、BBC加人量和初始溶液pH等因素对磷去除率的影响。实验结果表明:各因素对磷去除率影响的大小顺序依次为初始溶液pHBBC粒径初始磷质量浓度BBC加入量;BBC吸附水中磷的最佳反应条件为初始磷质量浓度26.81 mg/L,BBC粒径0.15 mm,BBC加入量10.6 g/L,初始溶液pH 4.42;在最佳反应条件下,BBC对磷的去除率达90.04%。     

污泥活性炭的制备及其对溶液中Cr6+的吸附

以城市污水厂剩余污泥为原料,采用ZnCl2作活化剂,热解制备污泥活性炭。实验结果表明,制备污泥活性炭的最佳条件热解温度为550℃,ZnCl2溶液浓度为3mol／L,ZnCl2溶液体积与污泥质量比（mL／g）为2．5：1,热解时间为25min。用所制备的污泥活性炭吸附溶液中的Cr6＋最佳吸附条件为：吸附时间90min,Cr6＋初始质量浓度50mg／L,污泥活性炭加入量0．2g,溶液pH2,在此条件下,Cr6＋去除率达99．9％。污泥活性炭对溶液中Cr6＋的吸附等温线属于I型,等温吸附方程可用Langmuir模型和Freundlich模型来拟合。     

Al掺加赤铁矿去除水中U（Ⅵ）的机理研究

采用共沉淀法制备了吸附剂铝掺加赤铁矿（Al-Hem）,并通过XRD、TEM等手段进行了表征,考察了初始pH、Al15-Hem加入量、吸附时间和初始U（Ⅵ）质量浓度对U（Ⅵ）去除率的影响。实验结果表明：在吸附温度为25℃、初始pH为6、Al15-Hem加入量为0.20 g/L、初始U（Ⅵ）质量浓度为5 mg/L、吸附时间为120 min的条件下,Al15-Hem对U（Ⅵ）的去除率为98.8%;Al15-Hem经4次解吸后,对U（Ⅵ）的去除率仍大于77.6%,具有一定的重复利用性;Al15-Hem对U（Ⅵ）的吸附以化学吸附为主,其机理可能是U（Ⅵ）与吸附剂表面含氧官能团发生了配位反应。     

氧化石墨烯负载纳米零价铁的制备及其对亚甲基蓝的吸附

采用液相还原法制备氧化石墨烯负载纳米零价铁吸附剂(Fe0/GO),并用于吸附去除溶液中的亚甲基蓝(MB)。考察了溶液p H、吸附温度、吸附时间、初始MB质量浓度对Fe0/GO吸附MB的影响。SEM等表征结果显示:Fe0以球形或短链形负载在GO上,增加了材料的反应活性位点;Fe0/GO的比表面积为158.32 m2/g,等电点为3。实验结果表明:在溶液p H为6、吸附时间5 h、吸附温度25℃的最佳条件下,加入400 mg/L的Fe0/GO,处理初始MB质量浓度为160 mg/L的MB溶液,MB去除率为89.26%,吸附量为125.5 mg/g;Langmuir等温吸附方程和Frenudlich等温吸附方程均能较好地描述Fe0/GO对MB的吸附过程;Fe0/GO对MB的吸附行为遵循准二级动力学方程;计算得出吸附温度为25℃、初始MB质量浓度为160 mg/L时的饱和吸附量为201.2 mg/g,平衡吸附量为124.3 mg/g。     

加拿大一枝黄花纤维素的改性及其对Cr(Ⅵ)的吸附

采用环氧氯丙烷和三甲胺对加拿大一枝黄花纤维素进行改性,改性后的加拿大一枝黄花纤维素对Cr(Ⅵ)具有一定的吸附作用.在改性加拿大一枝黄花纤维素加入量为3.2 g/L、吸附温度为40℃、吸附时间为240 min、溶液pH为2的条件下,对初始Cr(Ⅵ)质量浓度为20 mg/L的K2Cr2O7溶液进行吸附实验,Cr(Ⅵ)吸附量可达5.69 mg/g,Cr(Ⅵ)去除率为91％.动力学研究结果表明,改性加拿大一枝黄花纤维素对Cr(Ⅵ)的吸附以液膜扩散为控制步骤,反应过程符合Boyd液膜扩散方程,相关系数达到0.995 47.     

硝酸改性活性炭的制备及其对Cr（Ⅵ）

利用硝酸对颗粒活性炭进行改性,处理含铬废水,并考察了吸附时间、溶液pH、吸附剂加入量对改性活性炭吸附Cr（Ⅵ）效果的影响。实验结果表明：经过硝酸氧化改性的活性炭比表面积有所增加,官能团总量增加明显;吸附剂对Cr（Ⅵ）的去除率随振荡时间的增加而增加;对于质量浓度为10mg/L的100mLCr（Ⅵ）溶液,当溶液pH为中性,30%（体积分数）硝酸改性的颗粒活性炭的加入量为0.4g,其对Cr（Ⅵ）的最大去除率为98%。     

Optimizing Cr(VI) adsorption on activated carbon produced from heavy oil fly ash

In order to explore the beneficial utilization of heavy oil fly ash (HOFA) generated in the power plants, the present study is intended to optimize the chromium(VI) [Cr(VI)] adsorption on activated carbon produced from HOFA. The raw HOFA obtained from a power plant was washed by nitric/hydrochloric acid and activated at 800 °C with a holding time of 60 min to produce fly ash activated carbon (FAC). Phosphoric acid was used as a chemical agent to improve the surface characteristics of the HOFA during the activation process. Batch adsorption experiments were employed to evaluate the effects of different parameters such as initial Cr(VI) concentration, pH, and FAC dose on the removal of Cr(VI) from aqueous solution. A total of 17 adsorption experimental runs were carried out employing the detailed conditions followed the response surface methodology based on the Box–Behnken design. The results indicate that developed FAC has the potential for removing Cr(VI) from wastewater. Under the test conditions, a maximum of 91.51 % Cr(VI) removal efficiency was achieved.     

生物炭对铅离子的吸附性能

以废弃松木屑为原料,采用控制热分解法制备了生物炭。运用BET和FTIR等技术对生物炭进行了表征,考察了生物炭对铅离子的吸附效果,并探讨了吸附机理。表征结果显示,700℃氨气处理的生物炭,其比表面积和总孔体积显著增大。实验结果表明:生物炭对铅离子的吸附效果优于普通活性炭,且以700℃氨气处理的生物炭为最佳;随溶液pH的升高生物炭对铅离子的去除率增大,当pH为4~6时去除效果较好;在溶液pH为6、初始铅离子质量浓度为50 mg/L、吸附剂加入量为1 g/L、吸附时间为6 h的条件下,700℃氨气处理的生物炭对铅离子的去除率达99%以上;700℃氨气处理的生物炭的Langmuir吸附常数和Freundlich吸附常数远大于普通活性炭和其他工艺的生物炭;铅离子在生物炭上的吸附过程符合拟二级动力学方程。     

Removal of Cr6 + and Ni2+ from aqueous solution using bagasse and fly ash

Raw bagasse and fly ash, the waste generated in sugar mills and boilers respectively have been used as low-cost potential adsorbents. Raw bagasse was pretreated with 0.1N NaOH followed by 0.1N CH3COOH before its application. These low-cost adsorbents were used for the removal of chromium and nickel from an aqueous solution. The kinetics of adsorption and extent of adsorption at equilibrium are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental system. The effect of hydrogen ion concentration, contact time, sorbent dose, initial concentrations of adsorbate and adsorbent and particle size on the uptake of chromium and nickel were studied in batch experiments. The Sorption data has been correlated with Langmuir, Freundlich and Bhattacharya and Venkobachar adsorption models. The efficiencies of adsorbent materials for the removal of Cr(VI) and Ni(II) were found to be between 56.2 and 96.2% and 83.6 and 100%, respectively. These results were obtained at the optimized conditions of pH, contact time, sorbent dose, sorbate concentration of 100 mg/l and with the variation of adsorbent particles size between 0.075 and 4.75 mm. The order of selectivity is powdered activated carbon > bagasse > fly ash for Cr(VI) removal and powdered activated carbon > fly ash > bagasse for Ni(II) removal.     

Activated carbon from Ceiba pentandra hulls, an agricultural waste, as an adsorbent in the removal of lead and zinc from aqueous solutions

The ability of low-cost activated carbon prepared from Ceiba pentandra hulls, an agricultural waste material, for the removal of lead and zinc from aqueous solutions has been investigated. In the batch tests experimental parameters were studied, including solution pH, contact time, adsorbent dose and initial metal ions concentration. The adsorbent exhibited good sorption potential at pH 6.0. Maximum removal of lead (99.5%) and of zinc (99.1%) with 10 g/l of sorbent was observed at 50 mg/L sorbate concentration. Removals of about 60-70% occurred in 10 min, and equilibrium was attained at around 50 min for both metals. The functional groups (CO, SO,-OH) present on the carbon surface were responsible for the adsorption of metal ions. The adsorption parameters were analysed using both the Freundlich and Langmuir models. The data are better fitted by the Freundlich isotherm as compared to Langmuir model, and the adsorption capacities for lead and zinc were 25.5 and 24.1 mg/g, respectively. Kinetics of adsorption obeyed a second order rate equation and the rate constant was found to be 2.71 x 10(-2) and 2.08 x 10(-2) g/mg/min for lead and zinc, respectively. The desorption studies were carried out using dilute HCl, and the effect of HCl concentration on desorption was studied. Maximum desorptions of 85% for lead and 78% for zinc were attained with 0.15 M HCl.     

含油浮渣制备含碳吸附剂并用于含油污水的处理

以含油浮渣为原料制备含碳吸附剂,并用于含油污水的处理。用比表面分析仪和SEM技术对吸附剂进行表征。通过正交实验和单因素实验考察吸附剂加入量、吸附时间及温度、污水pH对污水处理效果的影响。表征结果显示,含碳吸附剂碳元素含量高达90%(w)以上,表面粗糙,孔径分布以中孔为主,比表面积477.5 m2/g,碘吸附值376.48 mg/g。实验结果表明:在吸附温度30℃及时间60 min、含碳吸附剂加入量20 g/L、污水pH为7的最佳实验条件下,处理初始COD为502.12 mg/L、石油类质量浓度45.31 mg/L.的含油污水,COD和石油类的去除率分别为91.51%和87.1%,处理后的COD和石油类质量浓度分别为42.62 mg/L和5.83 mg/1,达到GB 8978—1996《污水综合排放标准》中的二级排放标准;含碳吸附剂的污水处理效果优于术质活性炭。     

木质素活性炭的制备及其对硝基苯的吸附

利用工业碱木质素分别经KOH及H3PO4活化制备两种木质素活性炭（KAC和PAC）,并用于模拟硝基苯废水的处理。采用SEM和IR等手段对木质素活性炭进行了表征。考察了木质素活性炭加入量、废水pH、吸附时间等因素对硝基苯吸附量的影响。表征结果显示,KAC具有丰富的孔结构,PAC表面含有多种功能基团。实验结果表明： 在吸附温度298 K、初始硝基苯质量浓度250 mg/L、木质素活性炭加入量1.0 g/L、废水pH 3、吸附时间24 h的条件下,KAC及PAC对硝基苯的吸附量分别为237.8 mg/g和211.9 mg/g,去除率分别达到91%和84%; KAC及PAC对硝基苯的吸附过程符合拟二级动力学方程,吸附等温线满足Langmuir等温吸附方程;当解吸剂的V（乙醇）∶V（去离子水）=9时,在PAC和KAC上吸附的硝基苯的解吸率分别达到99%和93%;木质素活性炭重复使用5次后,KAC和PAC对硝基苯的吸附量分别为115.4 mg/g和130.7 mg/g。     

活性炭催化臭氧氧化水中诺氟沙星

以椰壳基活性炭为催化剂,采用催化臭氧氧化工艺降解诺氟沙星(NF),优化了工艺条件,评价了催化活性,并对反应机理进行了探讨。实验结果表明:活性炭催化臭氧氧化工艺的优化条件为臭氧通量80 mg/h、初始NF质量浓度15.0 mg/L、反应温度25℃、初始NF溶液p H 5.0;在该优化条件下反应60 min时,TOC去除率达51.5%,较单独臭氧氧化的32.5%和单独活性炭吸附的11.5%有明显改善;在活性炭催化臭氧氧化工艺中臭氧氧化与活性炭吸附之间存在一定的协同作用,活性炭具有较好的催化活性;活性炭催化臭氧氧化工艺对NF的去除主要是基于臭氧的直接氧化作用。     

聚乙烯亚胺改性UiO-66-NH2对水中U(Ⅵ)的吸附

采用聚乙烯亚胺(PEI)改性氨基化锆基金属有机骨架材料(UiO-66-NH₂)制备了UiO-66-NH₂/PEI,利用XRD、SEM和FTIR对产物进行了表征,并将其用于吸附水中的U(Ⅵ)。考察了UiO-66-NH₂/PEI吸附U(Ⅵ)的影响因素,并研究了吸附动力学和等温线。实验结果表明:UiO-66-NH₂/PEI对U(Ⅵ)具有良好的吸附效果,PEI与UiO-66-NH₂质量比为30%、溶液pH为6、吸附剂投加量为80 mg/L、吸附时间为120 min、初始U(Ⅵ)质量浓度为10 mg/L时,UiO-66-NH₂/PEI对U(Ⅵ)的去除率达98.2%(303 K下);UiO-66-NH₂/30%PEI对U(Ⅵ)的吸附在60 min内达到平衡,吸附过程符合准二级动力学模型和Langmuir模型,最大吸附量达452.49 mg/g。     

Experimental and Modeling Studies for the Removal of Crystal Violet Dye from Aqueous Solutions using Eco-friendly <Emphasis Type="Italic">Gracilaria corticata</Emphasis> Seaweed Activated Carbon/Zn/Alginate Polymeric Composite Beads

This research article describes, an eco-friendly activated carbon prepared from the Gracilaria corticata seaweeds which was employed for the preparation of biodegradable polymeric beads for the efficient removal of crystal violet dye in an aqueous solution. The presence of chemical functional groups in the adsorbent material was detected using FTIR spectroscopy. The morphology and physical phases of the adsorbent materials were analyzed using SEM and XRD studies respectively. Batch mode dye adsorption behavior of the activated carbon/Zn/alginate polymeric beads was investigated as a function of dosage, solution pH, contact time, initial dye concentration and temperature. Maximum dye removal was observed at a pH of 5.0, 1 g of adsorbent dosage with 60 mg/L dye concentration, 50 min of contact time and at 30 °C. The equilibrium modeling studies were analyzed with Freundlich and Langmuir adsorption isotherms and the adsorption dynamics was predicted with Lagergren’s pseudo-first order, pseudo-second order equations and intra particle diffusion models. The process of dye removal followed a pseudo second-order kinetics rather than pseudo first order. The thermodynamic parameters like standard Gibbs free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were determined and the results imply that the adsorption process was spontaneous, endothermic and increases the randomness between the adsorbent and adsorbate. The results from the experimental and correlation data reveal that the Gracilaria corticata activated carbon/Zn/alginate polymeric beads have proved to be an excellent adsorbent material for the removal of CV dye.