Rapid one-step assays for on-site monitoring of mouse and rat urinary allergens

Allergy to rodent proteins is common among laboratory animal workers. Sensitive methods to measure exposure to these allergens have been developed. These assays are, however, expensive, time-consuming, and require a laboratory facility and methodological expertise. A simple method to screen for allergen spread, or to test whether hygiene standards are maintained, would be useful. Lateral flow immunoassays (LFIAs) are especially suited for field settings; the tests are simple and results are visible within minutes. LFIAs were developed for detection of the rodent urinary allergens Mus m 1 and Rat n 1. Pilot studies were performed in animal facilities in three countries using both extracts from airborne dust samples and samples collected by wiping surfaces. For comparison and determination of sensitivity, the concentrations of rodent urinary allergens in the samples were also measured using enzyme immunoassays (EIAs). The LFIAs for rat and mouse urinary allergens had a detection limit of 31 pg allergen per mL in a buffer system with purified allergen standards. Results of environmental dust extracts tested in LFIAs correlated well with levels obtained using EIAs. Spread of rodent allergens, or non-adherence to hygiene around laboratory animal facilities, may aggravate rodent allergy. Using a simple, sensitive one-step assay, allergens can be detected to prevent allergen exposure. The results reveal that the rapid assays are suited for on-site demonstration of exposure to rodent allergens, and thus, useful in occupational hygiene practice.     

Airborne exposure to wheat allergens: optimised elution for airborne dust samples

Well-validated methods for measuring airborne occupational allergens are essential for effective control and reduction of allergen exposures. For wheat flour allergens, specific immunoassays are available, but there is a need for optimisation and standardization of sample processing procedures. Wheat flour allergen elution and storage were studied using airborne dust samples collected in bakeries with a new parallel sampler. Forty-eight series of 9 parallel filters were subjected to extraction procedures varying in elution medium, shaking method, extraction vial, and centrifugation speed. Wheat allergens were measured with enzyme immunoassays, and the effect of various procedures evaluated by mixed regression analyses. The stability of the eluted allergens was assessed after storage for 20 days and 4 months at -20 degrees C, in the presence or absence of casein in the medium. Only the type of elution medium had significant effects on allergen recovery: addition of Tween-20 resulted in 3- to 100-fold increased levels, an effect that was most pronounced at low concentrations. Allergen levels in extracts were stable for at least 4 months at -20 degrees C, irrespective of the presence of casein in the medium. Addition of Tween-20 to the elution medium is essential for optimal extraction of wheat allergen. The recommended procedure further includes the use of conventional polystyrene tubes, simple shaking methods, and centrifugation after extraction. Wheat dust extracts in PBS-Tween can be stored frozen for at least 4 months, and addition of a stabilising protein is not required.     

Exposure assessment in Beijing, China: biological agents, ultrafine particles, and lead

In this study, air samples were taken using a BioSampler and gelatin filters from six sites in Beijing: office, hospital, student dormitory, train station, subway, and a commercial street. Dust samples were also collected using a surface sampler from the same environments. Limulus amoebocyte lysate (LAL) and Glucatell assays were used to quantify sample endotoxin and (1,3)- ${\rm{\beta}} $ -d-glucan concentration levels, respectively. Enzyme-linked immunosorbent assay (ELISA) was used to measure the dust mite allergens (Der p 1 and Der f 1). Ultrafine particle and lead concentrations in these sampling sites were also measured using P-Trak and atomic absorption spectrometer, respectively. Analysis of variance (ANOVA) and linear regression analysis were used to analyze the concentration data. Higher culturable bacteria (12,639 CFU/m³) and fungi (1,806 CFU/m³) concentrations were observed for the train station and the subway system, respectively. For the rest of sampling sites, their concentrations were comparable to those found in western countries, ranging from 990 to 2,276 CFU/m³ for bacteria, and from 119 to 269 CFU/m³ for fungi. ANOVA analysis indicated that there were statistically significant differences between the culturable bacterial and fungal concentration levels obtained for different sites (p value = 0.0001 and 0.0047). As for dust allergens, endotoxin, and (1,3)-β -d-glucan, their concentrations also seemed to be comparable to those found in the developed countries. Airborne allergen concentrations ranged from 16 to 68 ng/m³. The dust-borne allergen concentration was observed to range from 0.063 to 0.327 ng/mg. As for endotoxin, the highest airborne concentration of 25.24 ng/m³ was observed for the commercial street, and others ranged from 0.0427 to 0.1259 ng/m³. And dust-borne endotoxin concentration ranged from 58.83 to 6,427.4 ng/mg. For (1,3)-β -d-glucan, the airborne concentration ranged from 0.02 to 1.2 ng/m³. Linear regression analyses showed that there existed poor correlations between those in airborne and dust-borne states (R²?=?0.002~0.43). In our study, the lowest ultrafine particle concentration about 5,203 pt/cm³ was observed in office and the highest was observed at the train station, up to 32,783 pt/cm³. Lead concentration was shown to range from 80 to 170 ng/mg with the highest also observed at the train station. The information provided in this work can be used to learn the general situation of relevant health risks in Beijing. And the results here suggested that when characterizing exposure both airborne and dust-borne as well as the environments should be considered.     

Sampling and analysis considerations for the determination of hexavalent chromium in workplace air

Airborne hexavalent chromium (Cr[VI]) is a known human respiratory carcinogen and allergen. Workers in a variety of industries may be exposed to airborne hexavalent chromium, with exposures frequently occurring via inhalation and/or dermal contact. Analytical methods for the measurement of Cr(VI) compounds in workplace samples, rather than for the determination of total elemental chromium in workplace air, are often desired because exposure limit values for Cr(VI) compounds are much lower than for total Cr. For years, sampling and analytical test methods for airborne Cr(VI) have been investigated so as to provide means for occupational exposure assessment to this highly toxic species. Inter-conversion of trivalent chromium (Cr[III]) and Cr(VI) can sometimes occur during sampling and sample preparation, and efforts to minimize unwanted redox reactions involving these chromium valences have been sought. Because of differences in toxicity, there is also interest in the ability to differentiate between water-soluble and insoluble forms of Cr(VI), and procedures that provide solubility information concerning Cr(VI) compounds have been developed. This paper reviews the state of the art concerning the measurement of airborne Cr(VI) compounds in workplace aerosols and related samples.     

Passive airborne dust sampling to assess mite antigen exposure in farming environments

The aim of this study was to estimate mite antigen exposure in farming environments by passive sampling of airborne dust. Antigen concentrations were measured with enzyme immunoassays specific for three storage mites (SM): Acarus siro, Lepidoglyphus destructor, Tyrophagus putrescentiae and the house dust mite (HDM) Dermatophagoides pteronyssinus. Dust samples were collected with electrostatic dust fall collectors (EDCs) in three different areas of cattle farms. EDCs were placed in cow stables (working area), in changing rooms (transit area) and in different rooms of farmer dwellings (living area). Mite concentrations in the living area of farm homes were compared to those of urban homes. In dust samples from stables, antigens of all four mite species could be detected. The highest exposure level was to L. destructor (median 56.7 μg/m(2)), the lowest to A. siro (median 14.4 μg/m(2)). Mite concentrations of different species showed no correlation within the cow stables. In comparison to stables, the median mite concentrations in farm homes were significantly lower, ranging from below the detection limit to 1.5 μg/m(2). Antigens of SM were predominantly found in changing rooms and kitchens, and HDM antigens were mainly detected in bedrooms. Antigens of all mites were measured the least often in living rooms. T. putrescentiae was the most prevalent mite in all room types, and the exposure levels correlated strongly between different rooms. The number of SM positive samples in farm homes was considerably higher than in urban homes, while the percentage of HDM positive samples did not differ significantly.     

A method for measuring dermal exposure to multifunctional acrylates

UV-curable acrylates are used increasingly for coating wood surfaces in the furniture industry. One of the active components, tripropylene glycol diacrylate (TPGDA), is known to be both an allergen and irritant to the skin. Methods to measure dermal exposure to skin irritants and allergens, such as acrylates, are insufficient for exposure assessment and there is none for this compound. The aim of this investigation was to develop a skin and surface sampling method, based on tape stripping, and a gas chromatographic method for quantitative analysis for assessing occupational skin exposure to multifunctional acrylates. Twelve adhesives were tested for their efficiency to remove TPGDA and UV-coating from a glass surface, the skin of guinea pigs and human volunteers employing the tape-stripping method in order to find the best performing tape. Variables that affect removal efficiency such as the applied dose and its retention time on the skin, tape adhesion time on the skin, and the number of strippings required to detect the contaminant from the skin were studied. Fixomull tape performed the best during sampling and analysis and had the most consistent removal efficiencies for the studied substances. The average removal efficiency with a single stripping at the 2 microliters TPGDA exposed skin sites was 85% (RSD = 14.1), and for UV-resin exposed sites 63% (RSD = 20.2). The results indicated that this method can be used for measuring dermal exposure to multifunctional acrylates efficiently, accurately, and economically. This method provides a sensitive and powerful tool for the assessment of dermal exposure to multifunctional acrylates both from the skin and from other contaminated surfaces in occupational field settings.     

A rapid lateral flow immunoassay for the detection of fungal alpha-amylase at the workplace

Fungal alpha-amylase is a flour supplement which is added to improve the quality of bakery products. Various studies have shown that exposure to this enzyme is an important risk factor for the development of bakers' allergy and this allergy is reported to be one of the most frequent causes of occupational asthma. A rapid assay was developed to monitor exposure to occupational allergens directly at the workplace. The sensitivity of the developed assay is 0.32 ng amylase mL(-1) in a buffer system with the commercially available alpha-amylase preparation Fungamyl 1600S as the standard. Initial validation tests (n = 33) were performed with airborne and settled dust from an industrial bakery. The new lateral flow immunoassay detected amylase in 22 of the 26 samples regarded as positive in an enzyme immunoassay, and was negative for all seven enzyme immunoassay-negative samples, while the four lateral flow immunoassay-negative/enzyme immunoassay-positive samples all had levels below 2 ng mL(-1). The sensitivity of 2 ng mL(-1) of the amylase lateral flow immunoassay is sufficient for first screening purposes and, therefore, this simple and rapid assay may allow direct on-site demonstration of work-related hazards of bio-allergen exposure. This would be particularly useful in occupational hygiene practice, especially in traditional or small-scale bakeries which lack the technological skills for testing the exposure to respiratory allergens.     

Mineralogy of Atmospheric Suspended Dust in Three Indoor And One Outdoor Location in Oman

The aim of this work is to characterize the mineral phases present in the atmosphere at three locations in northern Oman. Samples of atmospheric particles were collected using a high volume sampler. Three indoor and one outdoor location were chosen in this investigation. Sampling locations included a residential house located nearby the cement plant, a residential house located nearby a refinery plant, and a residential house located at Al-Suwayq residential area. Indoor air was sampled from these three houses. Moreover, for the Al-Suwayq residential house, sampling was also taken outside the house for comparison. The dust samples were analysed for their microanalysis characterization and their mineral contents as well. The microanalysis enabled us to identify the metals present in the particles. Furthermore, the mineralogical analysis of the sample filters showed the presence of quartz as the principal phase inside the house of Al-Suwayq, whereas quartz, dolomite, and gypsum were common phases outside the house. In the residential house nearby the cement plant, it was found that calcite, quartz, dolomite and goethite were the principal phases whereas the particles collected from the house nearby the refinery composed primarily of dolomite and calcite. The airborne dust collected at the refinery and Al-Suwayq were probably sourced in the natural environment and mobilised by natural processes. However, at the cement factory the crushing and grinding of limestone during the industrial process has contributed significantly to the airborne dust load. Generally, the information obtained in this study will be invaluable as no data for the mineral content of atmospheric dust existed in the Oman.     

New approaches for assessment of occupational exposure to metals using on-site measurements

Traditional assessment of occupational exposure to metals typically involves static or personal aerosol sampling on a membrane filter followed by a laboratory determination of the metal content on the filter sample. These techniques give results with high accuracy and low detection limits. However, they all have a drawback in that, since the samples have to be analysed in a laboratory, the results will usually be obtained days or weeks after the sampling took place. Today there is available a new generation of portable electronic micro-balances and instruments for metal analysis based on X-ray fluorescence. These instruments will make on-site measurements of metal exposure possible, which opens the way for new approaches for assessment of occupational exposure to metals. In combination with high-flow pumps, short-term sampling is possible, which allows monitoring of the exposure variation during a work shift as well as the exposure during individual work tasks of short duration. Screening measurements and emission measurements are other examples of monitoring that are facilitated using on-site determinations. Measure control monitoring can effectively be performed using on-site measurements and is an effective tool in the assessment of workplace improvements. On-site determinations can also form an effective and pedagogic tool showing workers how to perform specific tasks and demonstrating the effectiveness of different measures intended to improve their work environment. Other examples are the assessment of skin exposure using aerosol deposition on pads and screening of contamination using bulk samples.     

Documentation of bioaerosol concentrations in an indoor composting facility in France

Bioaerosol concentrations were investigated in a totally indoor composting facility processing fermentable household and green wastes to assess their variability. Stationary samples were collected by filtration close to specific composting operations and then were analysed for cultivable mesophilic bacteria, thermophilic bacteria, mesophilic fungi, thermophilic fungi, endotoxins and total airborne bacteria (DAPI-staining). Indoor concentrations exceeded the background levels, between 500 and 5400 EU m(-3) for endotoxins, 10(4) and 10(6) CFU m(-3) for cultivable bacteria and generally below 10(5) CFU m(-3) for airborne cultivable fungi. No significant (p > 0.05) differences were observed between the indoor composting operations. Successive 30 minute bioaerosol samples were collected to investigate the variation of cultivable mesophilic microorganisms over the work shift. Concentrations of mesophilic bacteria and fungi varied up to 1 log unit depending on the time at which they were collected in the day. Total airborne particles, counted using an optical particle counter, were present at up to 10(8) particles m(-3) and several concentration peaks were noted. Values for total airborne bacteria were roughly 70-fold higher than cultivable bacteria. These results raise the question of the sampling strategy (duration of sampling; number of samples to be collected) used in similar studies. They provide new bioaerosol concentration data in a composting facility and suggest that the filtration sampling method might be a useful tool for exposure measurements in that occupational environment.     

Biological monitoring of wood dust exposure in nasal lavage by high-performance liquid chromatography

A high-performance liquid chromatography (HPLC) method for biomonitoring of occupational wood dust exposure based on nasal lavage as a biomonitoring matrix was developed. Gallic acid (GA) was chosen as the indicator compound for oak dust exposure. From the chromatographic profile of ash dust, four peaks were chosen as indicator compounds. Phenolic indicator compounds were analysed by HPLC. Personal dust samples and corresponding nasal lavage samples were collected from 16 workers exposed to oak dust and six to ash dust. The dust concentrations in the workers' breathing zone varied between 0.7 and 13.8 mg m(-3). The indicators revealed the nature of the wood dust inhaled. For the workers who did not use respirators, the correlation between the dust and corresponding indicator compound in their nasal lavage was significant; r2 = 0.59 (n = 12) for oak dust and r2 = 0.58 (n = 6) for ash dust, respectively. Further, the correlation for oak dust workers who used respirators was r = 0.67 (n = 4). Nasal lavage sampling and HPLC analysis of polyphenol indicator compounds are promising tools for measuring wood dust exposure. Although further validation is necessary, determination of the individual dose may prove invaluable in prospective epidemiological studies.     

Evaluation of the methyl ester O-methyl acetate derivative of muramic acid for the determination of peptidoglycan in environmental samples by ion-trap GC-MS-MS

Muramic acid (MA) is a unique amino sugar that is a constituent of the peptidoglycan (PG) present in prokaryotic cell walls. MA can serve as a marker for quantifying bacterial load, e.g. in indoor environments, by using gas chromatography-tandem mass spectrometry (GC-MS-MS). We demonstrated recently that the methyl ester O-methyl acetate (MMA) derivative can be used to detect MA in house dust by ion-trap GC-MS-MS. However, since the MMA derivative is not formed from free MA quantification was not optimal. Here we report 1) significant improvements in sample preparation of the MMA derivative and 2) an evaluation of the performance of derivative, using for comparison the alditol acetate derivative, the gold standard in quantitative trace analysis of MA in complex matrices. The MMA derivative was analysed using an MS instrument with internal ionization and the alditol acetate derivative was analysed using an instrument with external ionization. 13C-labelled cyanobacteria, containing MA in their PG, were used as the internal standard. A linear relationship was found between the two methods in studies on 27 parallel samples of airborne dust from school classes collected on filters. Although the analytical sensitivity of the MMA derivatives was somewhat slightly lower than of the alditol acetate derivative, this may be due to differences in yield of derivative, sample clean-up efficiency, or different performance of the GC columns or MS instruments. However preparation of the MMA derivative is quick and compatible with preparation of methyl esters of 3-hydroxy fatty acids (used as markers of Gram negative endotoxin) allowing the levels of both markers to be determined in the same dust sample. In conclusion, the MMA procedure can be used to determine MA in environmental samples with good reproducibility provided the concentration of the 13C-labelled MA internal standard in the cyanobacteria is first determined with an alternative method.     

Assessment of workers' exposure to palladium in a catalyst production plant

Airborne particulate matter was collected and biomonitoring of workers was performed by sampling blood, urine and hair of 84 exposed subjects, 17 occasionally exposed employees, 21 controls from administrative offices and 25 unexposed people (external controls). Determination of Pd was performed using Quadrupole and High Resolution Inductively Coupled Plasma Mass Spectrometry. The Production of Catalysts Department and the Refining Service presented the highest levels of Pd in airborne matter collected by means of an area sampler. The highest level of soluble Pd (1.66 microg m(-3)) was found in the Production of Catalysts Department. The highest concentration of Pd in airborne matter, collected by means of personal devices (7.90 microg m(-3)) was found in the Refining Service. Hair showed a clear distribution pattern among departments, with values ranging from 0.60 to 5.54 microg g(-1). Administrative workers presented blood levels of Pd between 2 and 500 times higher than external controls. Only urine levels correlated with the measurements of airborne Pd collected with personal devices. A very strong association between airborne Pd collected by personal devices and Pd levels in hair (r(2)= 0.569, with p< or = 0.01) and urine (r(2)= 0.684, with p< or = 0.01) was found. On the basis of these findings: (i) blood results appear to be an unsuitable biological marker for occupational exposure to Pd; (ii) urine could be considered as a satisfactorily responsive bio-marker for occupational monitoring; and (iii) hair cannot be considered a good index of time-related exposure.     

Determination of germanium in urine and its usefulness for biomonitoring of inhalation exposure to inorganic germanium in the occupational setting

The present study aimed to assess whether urinary germanium concentration can be used as a biomarker of inhalation exposure to airborne dust from metallic germanium (Ge) or GeO2 in the occupational setting. A novel hydride generation-based method coupled with fow-injection graphite furnace atomic absorption spectrometry (HG/FI-GFAAS) was developed for the determination of urinary germanium. It was found that urinary germanium concentration could be reliably determined by a standard additions method after thorough digestion of the urine and careful pH adjustment of the digest. The limit of detection (LOD) in urine for the HG/FI-GFAAS method was 0.25 microg Ge L(-1). In Belgian control male subjects, the urinary germanium concentration was below this LOD. In 75 workers currently exposed to inorganic germanium compounds, respirable and inhalable concentrations of germanium in the aerosols were measured on Monday and Friday at the job sites using personal air samplers. Spot-urine samples were collected on the same days before and after the work shift. The germanium concentrations of respirable dust correlated very well with those of inhalable dust and represented 20% of the inhalable fraction. Workers exposed to metallic Ge dust were on average ten times less exposed to germanium than those whose exposure involved GeO2 (3.4 versus 33.8 microg Ge m(-3)). This difference was reflected in the urinary germanium concentrations (3.4 versus 23.4 microg Ge g(-1) creatinine). Regression analysis showed that the concentration of germanium in the inhalable fraction explained 42% of the post-shift urinary germanium concentration either on Monday or on Friday, whereas in a subgroup of 52 workers mainly exposed to metallic germanium dust 57% (r = 0.76) of the Monday post-shift urinary germanium was explained. Urinary elimination kinetics were studied in seven workers exposed to airborne dust of either metallic Ge or GeO2. The urinary elimination rate of germanium was characterised by half-times ranging from 8.2 to 18.1 h (on average 12 h 46 min). The present study did not allow discrimination between the germanium species to which the workers were exposed, but it showed fast urinary elimination kinetics for inhalation exposure to dust of metallic Ge and GeO2. It pointed out that urine samples taken at the end of the work shift can be used for biological monitoring of inorganic germanium exposure in the occupational setting.     

Assessing workplace chemical exposures: the role of exposure monitoring

Occupational exposure is the condition of being subjected through employment to a chemical, physical, or biological agent, or to a specific process, practice, behavior, or organization of work. Exposure to a chemical agent is typically the contact of that agent with the outer boundary of a subject, such as the respiratory system, skin, or digestive system. In occupational hygiene we are most concerned with exposure through the respiratory system, although, increasingly we are concerned with the results of dermal exposures, including those exposures to the skin that can be transferred to the mouth and digestive system. This presentation will detail methods available for assessing personal exposures to chemicals through monitoring. The results from monitoring can then be compared to established guidelines and regulations, although this is not the only rationale for making measurements. These monitoring methods are currently used around the world to establish the benchmark hazard from which risk to the worker can be predicted. The presentation will describe the general techniques for assessing exposures to the respiratory system from chemical gases and vapors, chemical dusts, and exposures to the skin from bulk chemicals or chemical contamination of surfaces. For respiratory exposures, direct-reading instruments are available for spot measurements, and for monitoring short-term fluctuations in concentration. However, most standards and regulations are based on time-integrated (time-weighted average) exposures, requiring longer-term integrative methods. Therefore, the specific focus of this review will be the methods available for full work-shift sampling. For gases and vapors this will include taking whole-air samples in canisters or polymer bags, or concentration of chemicals by absorption in liquids or adsorption on solid sorbents, with subsequent chemical analysis. Chemical concentration can take place by pumping air through the sorbing media, or by allowing molecules to diffuse to the sorbent surface. Transfer of the collected chemicals to the analytical instrumentation can be accomplished using solvent displacement and injection, or through the application of heat to bring the collected molecules back into the vapor phase. For particles, the particle size is important as this determines the site of deposition in the lungs, and so time-integrated sampling on filters using various types of size-selective samplers is preferred. Finally, some techniques that have been used to assess the potential for chemical contamination of the skin are presented. Biomonitoring is another tool that can be used to assess exposure, and the results are more relevant to dosimetric considerations than exposure. Biomonitoring is a complex subject worthy of a separate review, and will be considered only briefly here.     

Application of recent advances in aerosol sampling science towards the development of improved sampling devices: the way ahead

This paper reviews the framework that underpins the development of a new generation of personal samplers capable of operating at much lower flowrates that those of the current generation and so capable of being used for exposure assessment not only for 'traditional' occupational populations (i.e., industrial workers) but also for people exposed to aerosols in the ambient atmosphere (including children). The opportunity for this new generation of samplers stems from the availability of very light and compact low-flowrate pumps. The development and deployment of such instruments presents: (a) physical challenges in terms of how to collect particle size fractions in a manner which is consistent with the new particle size-selective sampling criteria, and (b) analytical challenges in terms of how to quantitate the much smaller amounts of collected material that need to be analysed. The paper lays out the physical and analytical scenarios, and points the way forward to how such challenges can be overcome. Work is already in progress in several countries to develop prototype instruments for applications like those described.     

Vacuum sampling techniques for industrial hygienists, with emphasis on beryllium dust sampling

The U.S. Department of Energy (DOE) Chronic Beryllium Disease Prevention Program Rule, 10 CFR Part 850 became effective in 2000 in response to the prevalence of Chronic Beryllium Disease (CBD) in workers. The rule requires surface and air monitoring for beryllium to determine exposure levels and the evaluation of the effectiveness of controls used to minimize or eliminate that risk. The most common methods for surface sampling use wet or dry wipes. Wipe sampling techniques may be impractical for many surfaces common to most buildings such as cinder block, textured wall surfaces, fabric and carpet. Vacuum sampling methods have been developed for the evaluation of lead or pesticides on residential surfaces such as carpets, bare floors and window sills. However, the current vacuum methods may be impractical for many workplace situations such as sampling of protective clothing, complex facility structures, or equipment surfaces. Recent work using vacuum sampling for potential bio-terrorism agents such as anthrax spores may have significant application to industrial hygiene evaluations of the workplace and may be extendable for use in sampling of metals such as beryllium. Validated vacuum sampling methods that provide meaningful data would be of great value to industrial hygienists in identifying areas having surface contamination, evaluating existing controls and work practices and determining the potential of toxic material on surfaces to become airborne and present a potential risk to workers and the public. This article discusses various vacuum sampling methodologies and recommends harmonization of sampling methods.     

A review of workplace aerosol sampling procedures and their relevance to the assessment of beryllium exposures

Standardized conventions governing the fractions of airborne particles that can penetrate the human head airways, the thoracic airways and the alveolar spaces have been internationally (although not universally) adopted. Several agencies involved in setting limit values for occupational exposure concentrations have taken these conventions into account when considering the appropriate standard for specific chemicals, in order to ensure the standards are biologically relevant. A convention is selected based on the characteristic health effects, and forms the basis of measurement against the limiting concentration value. In order to assess exposure for comparison to this metric or any other purposes, it is necessary to choose a sampler whose performance matches the convention, and protocols have been developed and used to test sampler performance. Several aerosol sampling devices are available, nominally at least, for each of the conventions. Some considerations important to the sampling of airborne particles containing beryllium with regard to the sampling conventions, the test protocols and sampler performance are discussed.     

静电场采样装置对室内空气中过敏原采集效率的研究

以Biosampler采样器为参照,采用平行重复的实验方法,以电压和流量作为匹配因素结合ELISA、LAL和GLUCANTELL技术,检测空气中过敏原Der p和Der f及内毒素和多聚糖.结果表明,静电场采样装置对4种生物气溶胶的采集效率要比Biosampler采样器高2倍～8倍,静电场采样法优于撞击式采样法.     

Validation of a standardized portable fluorescence method for determining trace beryllium in workplace air and wipe samples

Beryllium is widely used in industry for its unique properties; however, occupational exposure to beryllium particles can cause potentially fatal disease. Consequently, exposure limits for beryllium particles in air and action levels on surfaces have been established to reduce exposure risks for workers. Field-portable monitoring methods for beryllium are desired in order to facilitate on-site measurement of beryllium in the workplace, so that immediate action can be taken to protect human health. In this work, a standardized, portable fluorescence method for the determination of trace beryllium in workplace samples, i.e., air filters and dust wipes, was validated through intra- and inter-laboratory testing. The procedure entails extraction of beryllium in 1% ammonium bifluoride (NH(4)HF(2), aqueous), followed by fluorescence measurement of the complex formed between beryllium ion and hydroxybenzoquinoline sulfonate (HBQS). The method detection limit was estimated to be less than 0.02 microg Be per air filter or wipe sample, with a dynamic range up to greater than 10 microg. The overall method accuracy was shown to satisfy the accuracy criterion (A< or = +/-25%) for analytical methods promulgated by the US National Institute for Occupational Safety and Health (NIOSH). Interferences from numerous metals tested (in >400-fold excess concentration compared to that of beryllium) were negligible or minimal. The procedure was shown to be effective for the dissolution and quantitative detection of beryllium extracted from refractory beryllium oxide particles. An American Society for Testing and Materials (ASTM) International voluntary consensus standard based on the methodology has recently been published.