Exposure to airborne organophosphates originating from hydraulic and turbine oils among aviation technicians and loaders

This study describes the potential for occupational exposure to organophosphates (OPs) originating from turbine and hydraulic oils, among ground personnel within the aviation industry. The OPs tri-n-butyl phosphate (TnBP), dibutyl phenyl phosphate (DBPP), triphenyl phosphate (TPP) and tricresyl phosphate (TCP) have been emphasized due to their use in such oils. Oil aerosol/vapor and total volatile organic compounds (tVOCs) in air were also determined. In total, 228 and 182 OPs and oil aerosol/vapor samples from technician and loader work tasks during work on 42 and 21 aircrafts, respectively, were collected in pairs. In general, the measured exposure levels were below the limit of quantification (LOQ) for 84%/98% (oil aerosol) and 82%/90% (TCP) of the samples collected during technician/loader work tasks. The air concentration ranges for all samples related to technician work were 相似文献   

Wipe sampling as a tool for monitoring aerosol deposition in workplaces

As a complement to traditional exposure assessment, monitoring deposition of aerosols can be a simple and quick screening method for identifying deposited aerosols. In this presentation examples of screening studies, based on wipe sampling in combination with adequate analytical techniques, are described. These screening methods are rapid, simple and easy to carry out. The examples given in this presentation show a broad applicability and the methods are proven useful for assessing aerosol distribution in the workplace as well as to identify target spots for more extensive assessment of a worker's exposure situation.     

Passive aerosol sampler for particle concentrations and size distributions

This research evaluated the UNC passive aerosol sampler as a tool to measure particle mass concentrations and size distributions. The exposure scenario represented high concentrations and exposure periods of a few hours. Mass concentrations measured with the passive sampler were compared to concentrations measured using both a dichotomous sampler and an aerodynamic particle sizer (APS). In addition, the size distributions measured with the passive sampler were compared to those measured using the APS. Mass concentrations measured using the dichotomous sampler and the APS agreed well. The passive sampler tracked, but tended to overestimate, mass concentrations measured by the other two instruments. Size distributions measured with the passive sampler followed the general pattern of those measured using the APS. Overall, the passive sampler demonstrated both its utility and its limitations in these tests. The concentration measurements and size distributions found using passive samplers were more variable than those of the other instruments, but generally followed the data taken using the other methods. The advantages of low cost and ease of use offset the limitations in data quality with the passive sampler; these advantages are particularly welcome for sampling situations where aerosol properties vary over space or time.     

Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.     

A chemosorptive cylindrical denuder designed for personal exposure measurements of isocyanates-evaluation on generated aerosols of 4,4'-methylenediphenyl diisocyanate

A denuder/filter system constructed for solvent-free personal exposure measurements was evaluated for separation of vapour and particulate 4,4'-methylenediphenyl diisocyanate (4,4'-MDI) generated from heated PUR-foam. The two different phases were collected in the denuder and on the filter, respectively, by chemosorption on a polydimethylsiloxane (SE-30)-dibutylamine (DBA) stationary phase. Both repeatability and the total mass concentration of 4,4'-MDI were similar to that obtained from the reference method, in this case an impinger/filter system. The penetration of particles through the denuder at 300 ml min(-1) was nearly 100% in the particle size range 25 to 700 nm, which fits well with the Gormley-Kennedy equation. Denuder/filter sampling of the 4,4'-MDI aerosol at 500 ml min(-1) yielded a phase distribution that was in accordance with the results from the reference method. The method limit of detection was 6 ng m(-3) and 4 ng m(-3) for the denuder and filter, respectively, when using an air sampling flow rate of 300 ml min(-1) and a sampling period of 15 min. This is well below the Swedish occupational exposure limit (OEL) of 50 and 100 microg m(-3) for an 8-hour working day and a 5-min period, respectively.     

Use of portable X-ray fluorescence spectrometry for environmental quality assessment of peri-urban agriculture

Urban expansion into traditional agricultural lands has augmented the potential for heavy metal contamination of soils. This study examined the utility of field portable X-ray fluorescence (PXRF) spectrometry for evaluating the environmental quality of sugarcane fields near two industrial complexes in Louisiana, USA. Results indicated that PXRF provided quality results of heavy metal levels comparable to traditional laboratory analysis. When coupled with global positioning system technology, the use of PXRF allows for on-site interpolation of heavy metal levels in a matter of minutes. Field portable XRF was shown to be an effective tool for rapid assessment of heavy metals in soils of peri-urban agricultural areas.     

大气气溶胶中痕量金属元素的研究进展

综述了近年来国内外学者对大气气溶胶中痕量金属元素的研究进展,介绍了痕量金属元素的地球化学行为,以及大气气溶胶中痕量金属的源解析方法、在环境中的循环与污染、生物有效性及对人体的健康效应。建议研发更可靠的分析方法或在线检测仪器,避免采样和样品前处理过程中痕量金属的污染和损失;建立监测网络,形成区域性的大气监测模式,更全面地分析污染来源;与监测超级站建设、空气污染流行病学设计和毒性机制研究相结合,建立更加完善的研究体系。     

Field measurement of lead in workplace air and paint chip samples by ultrasonic extraction and portable anodic stripping voltammetry

On-site measurement of lead in workplace air filter samples and paint chip samples by ultrasonic extraction and anodic stripping voltammetry (UE-ASV) was evaluated in the field during renovation and remodeling activities in residences having leaded paint. Aerosol and paint samples were collected using standard techniques, and the samples were analyzed on-site for lead content by portable UE-ASV. Lead in sample extracts was subsequently determined by atomic absorption (AA) spectrometry in a fixed-site laboratory. The remaining sample extracts plus undissolved material (air filters or paint particles) were then subjected to hot plate digestion in concentrated nitric acid-30% hydrogen peroxide prior to AA analysis for lead. Field UE-ASV lead data were thereby compared to UE-AA and hot plate digestion-AA results from fixed-site laboratory lead measurement. Determination of lead in air filter samples by UE-ASV (over the range of 5 microg to approximately 800 microg Pb per sample) was extremely well correlated with lead measurement by UE-AA and hot plate digestion-AA procedures. However, a significant negative bias associated with ASV measurement was observed, and this was attributed to a matrix effect. Lead measurement in paint chip samples by UE-ASV (over the range of approximately 10 to approximately 550 microg Pb g(-1)) was well correlated with lead measurement by UE-AA and hot plate digestion-AA procedures. However, correlation and precision were lower for lead measurement in paint samples as compared to aerosol samples, and a negative bias was also observed. Lead measurements by UE-AA were compared to lead determinations by hot plate digestion-AA; these data were highly correlated and demonstrated no significant bias. Thus it was concluded that the ultrasonic extraction procedure performed equivalently to hot plate digestion. It was reasoned that matrix effects due to the preparation and analysis of paint chip particles resulted in greater imprecision as well as negative bias by ASV measurement. Despite significant negative bias in this sample set, UE-ASV offers promise for on-site measurement of lead in samples of interest in occupational and environmental health.     

无人机载核辐射监测及气溶胶采样系统试验分析

利用旋翼式无人机平台挂载机载式γ谱仪、气溶胶采样器及相关监控设备,在稳定风场下开阔平坦场地,对特征金属颗粒物随炸药爆炸后形成的气溶胶进行空中烟云跟踪取样及巡测,测量环境核辐射水平。结果表明,通过8次爆炸物气溶胶跟踪采样,以及放射性点源探测试验,证实旋翼式无人机空中气溶胶取样及对辐射测量的可行性。     

光散射法扬尘在线监测质量管理研究与应用

主要阐述了光散射法扬尘在线监测应用于建筑工地、干散货码头堆场、混凝土搅拌站的质量管理和质量评估。为了提高光散射法扬尘在线监测的数据质量,上海市采取扬尘在线监测设备现场质量抽测的模式,通过对在用仪器的监测点位、除湿方式、校准方式、质量浓度转换系数、与标准重量法监测结果的相对误差和相关系数、仪器运行维护水平等影响监测质量和数据有效性的关键指标的检查,开展扬尘监测在用仪器质量评估和仪器商合格评定,稳步提高在用仪器质量,为在线监测质量管理和质量评估提供可借鉴的技术方案和实践经验。     

Workplace aerosol mass concentration measurement using optical particle counters

Direct-reading aerosol measurement usually uses the optical properties of airborne particles to detect and measure particle concentration. In the case of occupational hygiene, mass concentration measurement is often required. Two aerosol monitoring methods are based on the principle of light scattering: optical particle counting (OPC) and photometry. The former analyses the light scattered by a single particle, the latter by a cloud of particles. Both methods need calibration to transform the quantity of scattered light detected into particle concentration. Photometers are simpler to use and can be directly calibrated to measure mass concentration. However, their response varies not only with aerosol concentration but also with particle size distribution, which frequently contributes to biased measurement. Optical particle counters directly measure the particle number concentration and particle size that allows assessment of the particle mass provided the particles are spherical and of known density. An integrating algorithm is used to calculate the mass concentration of any conventional health-related aerosol fraction. The concentrations calculated thus have been compared with simultaneous measurements by conventional gravimetric sampling to check the possibility of field OPC calibration with real workplace aerosols with a view to further monitoring particle mass concentration. Aerosol concentrations were measured in the food industry using the OPC GRIMM? 1.108 and the CIP 10-Inhalable and CIP 10-Respirable (ARELCO?) aerosol samplers while meat sausages were being brushed and coated with calcium carbonate. Previously, the original OPC inlet had been adapted to sample inhalable aerosol. A mixed aerosol of calcium carbonate and fungi spores was present in the workplace. The OPC particle-size distribution and an estimated average particle density of both aerosol components were used to calculate the mass concentration. The inhalable and respirable aerosol fractions calculated from the OPC data are closely correlated with the results of the particle size-selective sampling using the CIP 10. Furthermore, the OPC data allow calculation of the thoracic fraction of workplace aerosol (not measured by sampling), which is interesting in the presence of allergenic particles like fungi spores. The results also show that the modified COP inlet adequately samples inhalable aerosol in the range of workplace particle-size distribution.     

Assessing workplace chemical exposures: the role of exposure monitoring

Occupational exposure is the condition of being subjected through employment to a chemical, physical, or biological agent, or to a specific process, practice, behavior, or organization of work. Exposure to a chemical agent is typically the contact of that agent with the outer boundary of a subject, such as the respiratory system, skin, or digestive system. In occupational hygiene we are most concerned with exposure through the respiratory system, although, increasingly we are concerned with the results of dermal exposures, including those exposures to the skin that can be transferred to the mouth and digestive system. This presentation will detail methods available for assessing personal exposures to chemicals through monitoring. The results from monitoring can then be compared to established guidelines and regulations, although this is not the only rationale for making measurements. These monitoring methods are currently used around the world to establish the benchmark hazard from which risk to the worker can be predicted. The presentation will describe the general techniques for assessing exposures to the respiratory system from chemical gases and vapors, chemical dusts, and exposures to the skin from bulk chemicals or chemical contamination of surfaces. For respiratory exposures, direct-reading instruments are available for spot measurements, and for monitoring short-term fluctuations in concentration. However, most standards and regulations are based on time-integrated (time-weighted average) exposures, requiring longer-term integrative methods. Therefore, the specific focus of this review will be the methods available for full work-shift sampling. For gases and vapors this will include taking whole-air samples in canisters or polymer bags, or concentration of chemicals by absorption in liquids or adsorption on solid sorbents, with subsequent chemical analysis. Chemical concentration can take place by pumping air through the sorbing media, or by allowing molecules to diffuse to the sorbent surface. Transfer of the collected chemicals to the analytical instrumentation can be accomplished using solvent displacement and injection, or through the application of heat to bring the collected molecules back into the vapor phase. For particles, the particle size is important as this determines the site of deposition in the lungs, and so time-integrated sampling on filters using various types of size-selective samplers is preferred. Finally, some techniques that have been used to assess the potential for chemical contamination of the skin are presented. Biomonitoring is another tool that can be used to assess exposure, and the results are more relevant to dosimetric considerations than exposure. Biomonitoring is a complex subject worthy of a separate review, and will be considered only briefly here.     

Biological monitoring versus air monitoring strategies in assessing environmental-occupational exposure

Assessment of environmental and occupational exposure to chemicals can be performed with environmental monitoring (EM) and biological monitoring (BM). Biological monitoring was for a long time considered as a method complementary to environmental monitoring. At present this attitude is changing and in certain areas biological monitoring is applied as the method of choice for exposure and health-risk assessment. This paper examines advantages and disadvantages of those two approaches. In occupational settings environmental monitoring of exposure to VOCs seems to be superior to biological monitoring (possibility of simultaneous determination of components of mixtures, simple interpretation, possibility of evaluation of short-term exposure to local irritants). In the case of this group of compounds BM can be useful in selected cases such as evaluation of dermal absorption or efficiency of protective measures. In the case of metals both forms of monitoring can be used depending on the available methods for interpretation of results. BM of exposure may be considered as superior for evaluating the effects of exposure to lead, cadmium and mercury. However, quantitative evaluation of cancer risk after exposure to arsenic or chromium is possible only on the basis of determination in the air and the use of unit risk values. Both environmental and biological monitoring are useful for evaluation of occupational and environmental exposure to polycyclic aromatic hydrocarbons (PAHs). In certain areas such as evaluation of exposure to external tobacco smoking, cytostatic drugs, and pesticides, biological monitoring is the method of choice used for individual exposure assessment or tracing the trends of environmental exposure.     

Correlation of urinary nickel excretion with observed 'total' and inhalable aerosol exposures of nickel refinery workers

An investigation of the relationship between observed nickel aerosol exposures and urinary nickel excretion was undertaken at a Scandinavian nickel refinery. The goal of the study was to assess the impact of nickel aerosol speciation, the use of particle size-selective sampling instrumentation and adjustment of urinary levels for creatinine excretion on the usefulness of urinary nickel excretion as a marker for exposure. Urinary nickel measurements and paired 'total' and inhalable aerosol exposure measurements were collected each day for one week from refinery workers in four process areas. The mean observed urinary nickel concentration was 12 micrograms L-1 (11 micrograms of Ni per g of creatinine). The strongest relationships between urinary excretion and aerosol exposure were found when urinary nickel levels were adjusted for creatinine excretion and when exposure to only soluble forms of nickel aerosol was considered. No significant difference was observed between measures of 'total' and inhalable aerosol in the ability to predict urinary excretion patterns. In the light of these results, it is recommended that consideration be given to the chemical species distribution of nickel aerosol in the use of urinary nickel measurements as a screening tool for cancer risk in occupationally-exposed populations.     

Magnetic susceptibility measurements as proxy method to monitor soil pollution: the case study of S. Nicola di Melfi

The development of in situ, cheep, noninvasive, and fast strategies for soil monitoring is a crucial task for environmental research. In this paper, we present the results of three field surveys carried out in an industrial area of Southern Italy: S. Nicola di Melfi. The monitoring procedure is based on soil magnetic susceptibility measurements carried out by means of experimental protocols that our research group developed during the last years. This field surveys is supported by both geological characterization of the area and analytical determinations of metal concentrations in soils. Magnetic studies were carried out not only in situ but also in laboratory. Results show that, taking into account the influence due to the geomorphologic difference, soil magnetic susceptibility is an optimal indicator of the anthropogenic impact. So, our monitoring strategy discloses that the combined use of magnetic susceptibility measurements and soil geomorphology information may be used as a useful tool for the temporal monitoring of pollution evolution and for a fast screening of polluted zones.     

Magnetic susceptibility measurements as proxy method to monitor soil pollution: development of experimental protocols for field surveys

In the framework of the development of new methods for measuring and monitoring soil pollution, this paper deals with the use of magnetic methodologies to monitor the heavy metals presence in soils. In particular it shows a procedure for collecting magnetic susceptibility measurements in order to interpret them as proxy variable for monitoring heavy metals in soils. Magnetic measurements are carried out using a magnetic susceptibility meter with two different probes for in situ field surveys. The experimental procedure is divided in two parts. In the first part we carry out laboratory tests aimed to evaluate, for both the probes, the effective investigation depth for soil, the measurement reproducibility under different conditions, and the influence of water content. We complete this part comparing in situ measurements obtained by means of two probes with different characteristics. In the second part we carry out tests to evaluate the relationships between heavy metal levels and magnetic susceptibility values of soil samples. We investigate the variability of the magnetic susceptibility measurements contaminating different soil samples with well known concentration of heavy metals. Moreover we study the correlation between magnetic susceptibility values and metal concentrations, determined by means of AAS, in soil samples collected during a field survey. Results suggest that a careful check of the experimental procedure play a crucial role for using magnetic susceptibility measurements for heavy metals in situ monitoring. This is very helpful both for improving the quality of data and for making simpler data interpretation.     

Validation of a standardized portable fluorescence method for determining trace beryllium in workplace air and wipe samples

Beryllium is widely used in industry for its unique properties; however, occupational exposure to beryllium particles can cause potentially fatal disease. Consequently, exposure limits for beryllium particles in air and action levels on surfaces have been established to reduce exposure risks for workers. Field-portable monitoring methods for beryllium are desired in order to facilitate on-site measurement of beryllium in the workplace, so that immediate action can be taken to protect human health. In this work, a standardized, portable fluorescence method for the determination of trace beryllium in workplace samples, i.e., air filters and dust wipes, was validated through intra- and inter-laboratory testing. The procedure entails extraction of beryllium in 1% ammonium bifluoride (NH(4)HF(2), aqueous), followed by fluorescence measurement of the complex formed between beryllium ion and hydroxybenzoquinoline sulfonate (HBQS). The method detection limit was estimated to be less than 0.02 microg Be per air filter or wipe sample, with a dynamic range up to greater than 10 microg. The overall method accuracy was shown to satisfy the accuracy criterion (A< or = +/-25%) for analytical methods promulgated by the US National Institute for Occupational Safety and Health (NIOSH). Interferences from numerous metals tested (in >400-fold excess concentration compared to that of beryllium) were negligible or minimal. The procedure was shown to be effective for the dissolution and quantitative detection of beryllium extracted from refractory beryllium oxide particles. An American Society for Testing and Materials (ASTM) International voluntary consensus standard based on the methodology has recently been published.     

可伸缩延长气体采样装置在应急监测中的应用

提出了一种可伸缩延长气体采样装置,并将其与现场气体监测仪器配套使用。初步考察了延长采样装置中Teflon采样管长度对现场监测结果可能产生的影响,并对监测站实验室楼顶废气排出筒气体进行了实际样品监测。结果表明,该装置可有效提高现场应急监测的安全防护保障效果,增加可监测区域范围,使现场应急监测工作能够为突发性环境污染事件的处置提供更多技术支持。     

Hygienic guidance values for wipe sampling of antineoplastic drugs in Swedish hospitals

The use of antineoplastic drugs in health care steadily increases. Health care workers can be occupationally exposed to antineoplastic drugs classified as carcinogenic or teratogenic. Monitoring of surface contamination is a common way to assess occupational exposure to antineoplastic drugs, since wipe sampling is used as a surrogate measure of dermal exposure. Since no occupational limits for antineoplastic drugs in work environments exist, 'hygienic guidance values' (HGVs) should be used instead. HGVs are practicable, achievable levels, not health based, and can be calculated from exposure data from representative workplaces with good occupational hygiene practices. So far, guidance values for surface monitoring of antineoplastic drugs only exist for pharmacies where antineoplastic drugs are prepared. The objective was to propose HGVs for surface monitoring of cyclophosphamide (CP) and ifosfamide (IF) in Swedish hospitals where antineoplastic drugs are administered to patients. In total, 17 workplaces located at six hospitals in Sweden were surveyed by wipe sampling. Wipe samples were collected, worked up and then analyzed with liquid chromatography tandem mass spectrometry. Surface contamination of CP and IF was found on 80% and 73% of the sampled surfaces, thus indicating that there is potential for health care workers to be exposed to CP and IF via the skin. The median surface load of CP was 3.3 pg cm(-2) (range <0.05-10,800 pg cm(-2)). The corresponding value for IF was 4.2 pg cm(-2) (range <0.13-95,000 pg cm(-2)). The highest surface loads were found on the floors. The proposed HGVs were set at 90th percentile values, and can be applicable to hospital workplaces where patients are treated with CP or IF. Surface monitoring combined with HGVs is a useful tool for health care workers to regularly benchmark their own surface loads which could control and reduce the occupational exposure to CP and IF in hospital workplaces. Thus, the occupational safety of the health care workers will be increased.     

土壤重金属快速监测技术研究与应用进展

土壤重金属污染已经日益成为社会的主要环境污染问题之一,土壤重金属快速监测技术对于土壤重金属污染的快速有效筛查与监控具有重要意义。介绍了近年来国内外土壤重金属快速监测方法,并阐述了相关土壤重金属快速监测仪器的研究现状。在土壤重金属快速监测领域,X射线荧光光谱技术优势明显,激光诱导击穿光谱技术亦发展迅速,基于免疫学、酶抑制原理的快速监测技术正处于发展阶段。随着快速监测技术理论和方法的不断完善,土壤重金属快速监测仪器朝着高精度、小型化、智能化的方向发展,在区域性土壤重金属含量评估方面的应用将逐步拓展。