Visibility impairing aerosols in the urban atmosphere of Delhi

To study the visual air quality of Delhi, size fractionated aerosols – coarse and fine fractions of PM₁₀ – were collected and analysed for and EC at three sites with different background activities. The analysed species constitute a smaller portion of coarse fraction (39%) but a larger portion of fine fraction (69%). The sampling was performed from June 2003 to November 2003 which covers monsoon and post monsoon seasons.Aerosol data was used to describe the spatial variation of Visibility Range as a function of chemical composition of visibility impairing aerosols. During the study period, visibility was found to be poor varying between 4.7 and 13 km with an average value of 9.4 km. It is observed that visibility impairment was more due to carbonaceous aerosol followed by sulphate.     

The influence of geometry and draught shields on the performance of passive samplers

Passive samplers provide an excellent opportunity to perform indicative measurements or establish a dense network of measuring sites. A drawback compared with conventional active measuring methods is the larger spread of results. This variation can, to a large extent, be attributed to the influence of temperature, sampler geometry and wind on sampling results. A proper design of sampler geometry and optimum choice of draught shield can reduce the influence of wind velocity on a badge type sampler to less than 10%. Wire mesh screens prove to be inadequate in damping turbulence. Filters give good results. Attention should be paid to the size and isolation value of the walls of the sampler to prevent thermal updrafts occurring within the sampler. Tube type samplers are less influenced by wind, provided that turbulence is prevented from influencing diffusion within the sampler.     

Characterization of thermally generated aerosols from polyurethane foam

Isocyanates constitute a group of highly reactive chemicals used on a large scale for the production of flexible polyurethane (PUR) foam. Exposure to isocyanates is known to produce irritation of the mucous membranes and the eyes. Isocyanates also have strong sensitizing properties and may cause occupational asthma. It is therefore important to monitor isocyanate emissions at workplaces. To obtain information for the improvement of isocyanate samplers and for health risk assessments of exposure, the emitted aerosol from two types of flexible PUR foam subjected to thermal degradation was characterized. Particle size distribution and toluene diisocyanate (TDI) concentration in the emitted aerosols were measured. Thermal degradation of flexible PUR foam at temperatures from 250 to 300 degrees C produced an aerosol with a geometric mean particle diameter of 30-50 nm. Between 5% and 9% of the PUR foam was emitted as TDI, and 2% to 6% of TDI monomers were found in the particle phase under the experimental conditions used. The 2,6-TDI isomer was more abundant in the gas phase than in the particle phase.     

The influence of race and gender on perceptions of community impact

Since 1968, research in public transportation planning has included an increasing number of analyses of the perceptions and attitudes of people who use and live in proximity to the systems (Nash and Hille 1968, McMillan et al. 1969, Wachs 1976). The results of the study reported here suggest that race and gender may explain more about attitudes toward the community impact of a transit system than do the levels of user satisfaction with the system. The implication for future research in this area is that surveys employing “satisfaction” and “importance” as indicators may not be using appropriate indices of evaluation. This study reports the results of a 1980 attitude survey of the perceptions of black and white men and women living within a two-block corridor along the Metropolitan Atlanta Rapid Transit Authority (MARTA) east line in Atlanta, Georgia. The research supports the Atlanta Regional Commission (ARC) Transit Impact Monitoring Program (TIMP). The survey used a stratified random sample technique to identify 100 households in which in-home interviews were subsequently conducted. A further stratified sampling procedure designated the gender and age of persons to be interviewed. The analysis included the isolation of responses by gender and race and used the chi-square statistic at the 0.05 significance level. The results identity differences in responses of males and females, blacks and whites.     

SEM-EDX analysis of various sizes aerosols in Delhi India

Scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) was used to understand the differences in morphology, elemental composition and particle density of aerosols in different five size ranges to further investigate the potential sources as well as transport of pollutants from/at a much polluted and a very clean area of Delhi. Aerosol samples were obtained in five different size ranges viz. > or = 10.9, 10.9-5.4, 5.4-1.6, 1.6-0.7 and < or = 0.7 microm from a considerably very clean and a much polluted area of Delhi. It was observed that at polluted area most of the particles irrespective of size are of anthropogenic origin. At clean area, in coarse size fractions particles are of natural origin while in fine size range the presence of anthropogenic particles suggests the transport of particles from one area to the other.     

The influence of denture cleansers on the release of organic compounds from soft lining materials

Biocompatibility constitutes the most fundamental requirement with respect to all dental materials to be applied within the oral cavity. In its environment, various toxic compounds may be released by dental materials which pose potential threats to the patient's health. Due to the fact that dentures remain in the oral cavity for a very long time, a detailed examination and verification of prosthetic materials with a view to their toxicity seems to be essential. By using very sensitive measurement techniques such as gas chromatography, one may determine which compounds are released by these materials. The aim of this paper was to determine the influence of various denture cleansers on the release of organic compounds from four soft dental materials used in prosthetics for lining dentures. These materials when placed in commonly used disinfectants (Corega Tabs, sodium hypochlorite, chlorhexidine, hydrogen peroxide), as well as in artificial saliva, produced 13 chemical compounds such as monomers (methyl methacrylate, ethyl methacrylate, dodecyl methacrylate), plasticizers (dibutyl phthalate, diethyl phthalate, tributyl acetylcitrate) and others (e.g. benzophenone). A comparison of chemical compounds released from acrylic-based materials and those released from silica-based materials demonstrated that acrylic-based materials are less resistant to disinfectants.     

Evaluation of airborne lead in the welding working environment

Manual and automatic welding machines (which use leaded alloys) are considered to be important sources of the emission of lead fumes into the general air of the working environment. Three workplaces at a television factory were selected for the present study, to determine the control class of the working unit. The concentrations of conventional measurements ("A" sampling points) were lower than the administrative control level (statutory standard of lead, 150 microg m(-3)), whereas the maximum concentration of 264.1 microg m(-3) ("B" sampling point) was higher at one working unit than the administrative control level. However, the control classes varied between class III (bad) and class I (good).     

Sample damage during X-ray fluorescence analysis--case study on ammonium salts in atmospheric aerosols

Atmospheric aerosols can consist of, amongst others, compounds like NH(4)NO(3) or (NH(4))(2)SO(4). Such components can suffer radiation damage and/or evaporate during EDXRF measurements, providing errors on successively applied analysis. The aim of this work is to investigate the influence of measurements using conventional EDXRF on the volatile compounds and to compare it with the influence of polarized beam EDXRF using secondary targets (and hence indirect irradiation). The effect of different parameters (acquisition time, accelerating voltage, current and medium) on the concentration loss was studied. The measurements performed in vacuum during a long period lead to the highest losses of volatile compounds. The influence of direct irradiation was proved to be larger than the indirect variant.     

The influence of pH and temperature on the aqueous geochemistry of neodymium in near surface conditions

Geochemical calculations were employed for the solubility and speciation of neodymium in a model soil solution as a function of pH. The calculations were based on the recently determined stability constants for Nd and solubility product for the Nd end-member of mineral monazite (NdPO(4)). Simulations were carried out at near neutral pH (pH 6.0 to pH 7.5) and 25 degrees C at the atmospheric CO(2) partial pressure. Additional calculations were also performed to assess Nd mobility at the extreme temperature conditions (300 degrees C) at neutral pH. Our results suggest that relatively dilute (Ionic Strength, I = 0.1), low-temperature waters may transport very small quantities of rare earth elements and actinides to the surficial environment at near neutral pH conditions. Evidently, higher temperature or extreme fluid composition may have a greater potential for mobilization of these elements. The results are pertinent to researchers interested in engineering applications for the precipitation of Nd and surrogate actinides from aqueous nuclear wastes.     

Validation of atmospheric aerosols parallel sampling in a multifold device

In this work, particulate matter was collected using an active sampling system consisting of a PM₁₀ (<10 μm) inlet coupled to a multifold device containing six channels, connected to a vacuum pump. Each channel was equipped with a filter holder fitted with adequately chosen filters. The system was fixed on a metallic structure, which was placed on the roof of the laboratory building, at the Faculty of Sciences, in Lisbon. Sampling took place under flow-controlled conditions. Aerosols were extracted from the filters with water, in defined conditions, and the water-soluble fraction was quantified by ion chromatography (IC) for the determination of inorganic anions (Cl^?, NO₃ ^? and SO₄ ^2?). Equivalent sampling through the various channels was validated. Validation was based on the metrological compatibility of the content results for the various filters. Ion masses are metrologically equivalent when their absolute difference is smaller than the respective expanded uncertainty. When this condition is verified, the studied multifold device produces equivalent samples.     

Detection and quantification of Cladosporium in aerosols by real-time PCR

Cladosporium is one of the most common airborne molds found in indoor and outdoor environments. Cladosporium spores are important aeroallergens, and prolonged exposure to elevated spore concentrations can provoke chronic allergy and asthma. To accurately quantify the levels of Cladosporium in indoor and outdoor environments, two real-time PCR systems were developed in this study. The two real-time PCR systems are highly specific and sensitive for Cladosporium detection even in a high background of other fungal DNAs. These methods were employed to quantify Cladosporium in aerosols of five different indoor environments. The investigation revealed a high spore concentration of Cladosporium (10(7) m(-3)) in a cow barn that accounted for 28-44% of the airborne fungal propagules. In a countryside house that uses firewood for heating and in a paper and pulp factory, Cladosporium was detected at 10(4) spores m(-3), which accounted for 2-6% of the fungal propagules in the aerosols. The concentrations of Cladosporium in these three indoor environments far exceeded the medical borderline level (3000 spores m(-3)). In a power station and a fruit and vegetable storage, Cladosporium was found to be a minor component in the aerosols, accounted for 0.01-0.1% of the total fungal propagules. These results showed that monitoring Cladosporium in indoor environments is more important than in outdoor environments from the public health point of view. Cladosporium may not be the dominant fungi in some indoor environments, but its concentration could still be exceeding the threshold value for clinical significance. The methods developed in this study could facilitate accurate detection and quantification of Cladosporium for public health related risk assessment.     

The influence of two culturing techniques on toxicity of four chemicals in Arabidopsis

Plots of Arabidopsis thaliana L. (Heynh.) plants were grown in two hydroponic systems, one using a solid rooting support media (vermiculite) and the other a flowing solution culture. Both were tested with various concentrations of bromacil (5-bromo-3-sec-butyl-6-methyluracil), dichlobenil (2,6-dichlorobenzonitrile), copper sulfate (CuSO₄·5H₂O) and 3-aminotriazole. The effects on biomass production were compared. Plants treated with bromacil at concentrations up to 0.05 mg l^–1 were similarly reduced in growth in both culture methods. However, the toxic effects of dichlobenil, copper sulfate and 3-aminotriazole were different for both culture methods. Dichlobenil decreased plant growth in the solution culture at lower concentrations than in the vermiculite system. All aspects of growth were suppressed in the solution culture while the vegetative weight was unaffected in the vermiculite culture. Plants treated with 20 mg l^–1 copper sulfate in solution culture yielded mean seed weight of 1.2 g/plot compared to 3.1 g/plot when treated with the same concentration in the double-plot system. Plants treated with 0.5 mg l^–1 3-aminotriazole in solution culture produced no seed, while plants with the same nominal concentration in the double-pot method produced a mean seed weight of 6.5 g/plot. Solution culture testing was generally more sensitive and since roots were bathed directly in a solution of known pH, nutrient level and chemical concentration, the test conditions were more accurately defined.     

Attribution of aerosol light absorption to black carbon and volatile aerosols

We investigated the contribution of volatile aerosols in light-absorption measurement by three filter-based optical instruments [aethalometer, continuous light-absorption photometer (CLAP), and continuous soot monitoring system (COSMOS)] at Gosan Climate Observatory (GCO) from February to June 2012. The aerosol absorption coefficient (σ _abs) and the equivalent black carbon (BC) mass concentration (M _BC) measured by the aethalometer and CLAP showed good agreement with a difference of 9 %, which is likely due to the instrumental uncertainty. However, σ _abs and M _BC measured by the COSMOS with a heated inlet were found to be approximately 44 and 49 % lower than those measured by the aethalometer and CLAP under ambient conditions, respectively. This difference can be attributed to the light absorption by the volatile aerosols coexisting with the BC. Even considering inherent observational uncertainty, it suggests that approximately 35–40 % difference in the σ _abs and M _BC can be contributed by volatile aerosols. Increase in the difference of M _BC measured by the aethalometer and COSMOS with the increasing thermal organic carbon (OC) measured by Sunset OC/EC analyzer further suggests that the filter-based optical instruments without the use of a heater are likely to enhance the value of σ _abs and M _BC, because this sample air may contain both BC and volatile aerosols.     

Elemental and individual particle analysis of atmospheric aerosols from high Himalayas

Atmospheric aerosols were collected during the scientific expedition to Mt. Qomolangma (Everest) in May–June, 2005. The elemental concentrations of the aerosols were determined by inductively coupled plasma mass spectrometry. This yielded data for the concentration of 14 elements: Na, Mg, Al, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, and Pb. The mean elemental concentrations were generally comparable with those from central Asia and the Arctic, while much higher than those from Antarctic. Size, morphology, and chemical composition of 900 individual aerosol particles were determined by scanning electron microscopy and energy-dispersive X-ray microanalysis. Based on morphology and elemental composition, the particles were clustered into eight groups: soot (8%), tar ball (3%), alumosilicates/silica (55%), calcium sulfate (16%), Ca/Mg carbonate (2%), Fe/Ti-rich particles (3%), Pb-rich particles (1%), and biological particles (12%). The sampling site, located at 6,520 m in the Himalayas, is particularly remote and located at high altitude. Nonetheless, high aerosol enrichment factors for copper, chromium, lead, nickel, vanadium, and zinc all suggest the influence of long-range transported pollution, while enrichment in calcium and the presence of alumino-silicates in individual particle analyses indicates a distinct mineral dust influence. The backward air mass trajectories showed that the northwestern part of India may contribute to the atmospheric aerosol in the central high Himalayas.     

Thermodynamic influences on size fractionated measurements (PM 2.5, PM 10) of ambient aerosols

Mass concentrations of PM 10 and PM 2.5 are planned as new standards for the monitoring of ambient air quality in the European Union. Standard procedure is the removal of particles > 10 microns and > 2.5 microns aerodynamic diameter, respectively, by impaction in a preseparator. Different samplers work according to different principles of flow control. The influence of ambient temperature, pressure and relative humidity on different devices is calculated to estimate the comparability of various aerosol samplers. Therefore, the effects of these ambient factors on the volume flow as well as on the cut-off dp50 are investigated. In a second step, the influence of relative humidity on the flow control device is calculated. The results show that the cut-off shifts (up to 6.4%) for varying ambient conditions. Therefore, the influence on the impaction process should not be neglected and an 'ideal sampler' would measure temperature, pressure and relative humidity and adapt the volume flow to avoid a systematic error in the cut-off.     

Chemical mass balance model for source apportionment of aerosols in Bombay

Aerosol samples collected within an industrial region of Bombay were analyzed for elemental concentrations using inductively coupled plasma emission spectroscopy, ultraviolet/visible spectrophotometry and X-ray fluorescence spectroscopy. Nineteen elements were selected as tracers of identified sources of aerosol in the region. The U.S. EPA chemical mass balance model was employed for source apportionment. Seven major source types were identified and the performance of the model was evaluated at different sampling locations. Model results were unsatisfactory at highly polluted sites in the study regions. It was found that U.S. EPA source profiles are not suitable for such regions in India and site-specific source profiles should be used in the application of chemical mass balance for source apportionment.     

The relative influence of nutrients and habitat on stream metabolism in agricultural streams

Stream metabolism was measured in 33 streams across a gradient of nutrient concentrations in four agricultural areas of the USA to determine the relative influence of nutrient concentrations and habitat on primary production (GPP) and respiration (CR-24). In conjunction with the stream metabolism estimates, water quality and algal biomass samples were collected, as was an assessment of habitat in the sampling reach. When data for all study areas were combined, there were no statistically significant relations between gross primary production or community respiration and any of the independent variables. However, significant regression models were developed for three study areas for GPP (r ² = 0.79–0.91) and CR-24 (r ² = 0.76–0.77). Various forms of nutrients (total phosphorus and area-weighted total nitrogen loading) were significant for predicting GPP in two study areas, with habitat variables important in seven significant models. Important physical variables included light availability, precipitation, basin area, and in-stream habitat cover. Both benthic and seston chlorophyll were not found to be important explanatory variables in any of the models; however, benthic ash-free dry weight was important in two models for GPP.     

Spatial and temporal variations in inhalable CuZnPb aerosols within the Mexico City pollution plume

We report on the CuPbZn content of PM10 and PM2.5 samples collected from three sites (urban T0, suburban T1 and rural T2) during the Mexico City MILAGRO campaign of March 2006. Daytime city centre concentrations of summation operator CuZnPb(PM10) were much higher (T0 > 450 ng m(-3)) than at the suburban site (T1 < 200 ng m(-3)). Rural site (T2) summation operator CuZnPb(PM10) concentrations exceeded 50 ng m(-3) when influenced by the megacity plume but dropped to 10 ng m(-3) during clean northerly winds. Nocturnal metal concentrations more than doubled at T0, as pollutants became trapped in the nightly inversion layer, but decreased at the rural site. Transient spikes in concentrations of different metals, e.g. a "copper event" at T0 (CuPM10 281 ng m(-3)) and "zinc event" at T1 (ZnPM10 1481 ng m(-3)) on the night of March 7-8, demonstrate how industrial pollution sources produce localised chemical inhomogeneities in the city atmosphere. Most metal aerosols are <2.5 microm and SEM study demonstrates the dominance of Fe, Ti, Ba, Cu, Pb and Zn (and lesser Sn, Mo, Sb, W, Ni, V, As, Bi) in metalliferous particles that have shapes including spherical condensates, efflorescent CuZnClS particles, cindery Zn, and Cu wire. Metal aerosol concentrations do not change in concert with PM10 mass, which is more influenced by wind resuspension than industrial emissions. Metalliferous particles can induce cell damage, and PM composition is probably more important than PM mass, with respect to negative health effects, so that better monitoring and control of industrial emissions would likely produce significant improvements in air quality.     

The influence of estuarine water quality on cover of barnacles and Enteromorpha spp.

The influence of ambient water quality on the settlement of barnacles and the green alga Enteromorpha spp. to an artificial substratum in the estuaries of Sydney, Australia, was investigated to test the efficacy of both groups of organisms as indicators of changes in water quality due to urban stormwater runoff and/or sewage overflows. Wooden settlement panels were immersed for 4 months on 17 occasions between 1996 and 2005 at 11 locations known to vary in water-quality parameters (conductivity, total uncombined ammonia, oxidised nitrogen, total nitrogen, filterable phosphorus, total phosphorus, faecal coliforms and chlorophyll-a) and ambient meteorological conditions (total rainfall, maximum rainfall). Water-quality data were collected during the time that the settlement panels were deployed. Cover of barnacles was highly variable among locations (range 1.2?C55.2%). Hierarchical partitioning found that chlorophyll-a, total phosphorus and total nitrogen had significant independent positive effects on barnacle cover. Together, these variables explained 26% of the variation in barnacle cover. Mean cover of Enteromorpha spp., however, did not vary significantly among locations suggesting that other potentially more important factors are influencing its settlement and growth. The results of this study suggest that barnacle cover is likely to be a useful indicator of some components of water quality.