赤泥晶种法诱导磷酸铵镁结晶回收模拟废水中磷的可行性研究

对赤泥的理化性质进行了分析,探索了以赤泥为晶种磷酸铵镁(MAP)结晶法从模拟废水中回收磷工艺。结果表明,经过研磨的赤泥颗粒属无孔物质或者大孔物质;将赤泥溶于水时有碱液和离子溶出,赤泥的主要化学成分为Ca、Al、Si和Mg等元素。投加赤泥晶种有利于磷酸铵镁结晶的形成。在初始磷酸盐浓度为90 mg/L、N∶Mg∶P摩尔比为1∶1∶1、不调节pH值、搅拌时间30 min、搅拌速度180 r/min、沉淀时间30 min条件下,赤泥粒径为60～80目、投加量为8 g/L时,以赤泥作为晶种诱导磷酸铵镁结晶回收磷的效果最优。干燥晶种的使用次数对磷酸根离子的回收率影响不大。所得结晶产物是一种很好的缓释肥。     

磷酸铵镁碱促(Mg(OH)_2)热解产物氨氮去除性能

磷酸铵镁热解循环技术可以有效降低磷酸铵镁结晶技术的药剂费用。同时,在磷酸铵镁热解过程中添加Mg(OH)2碱促媒介,能阻止磷酸氢镁向焦磷酸镁的转化,并降低热解产物氨氮去除过程中上清液磷酸盐的残留。在Mg(OH)2∶NH+4摩尔比为1∶1,热解温度为110℃条件下,热解产物沉氨效率接近84%,上清液磷酸盐残留量为0.02 mg/L。     

MAP沉淀法去除渗滤液中低浓度氨氮

考察了pH值、搅拌时间、Mg∶N和N∶P摩尔比对鸟粪石化学沉淀法(MAP)去除垃圾渗滤液中低浓度氨氮的影响,使用Design Expert 7.1.3进行3水平4因素响应曲面中心复合设计优化实验,并通过二次多项式拟合和参数优化,得到:当pH为10,搅拌时间为30 min,Mg∶N摩尔比为1.41,N∶P摩尔比为1.34时,氨氮去除率(Y1)可以达到最大值71.2%,体系中的残留PO34--P浓度(Y2)趋近于零,达到我国《生活垃圾填埋场污染控制标准排放标准》的排放标准。此外,X射线衍射图谱的分析表明大部分沉淀物质为磷酸铵镁。     

磷酸铵镁沉淀法回收尿液中N和P的实验研究

以源分离尿液为研究对象,在氨氮含量为2 850 mg N/L的微稀释尿液中,投加MgCl2.6H2O和Na2HPO4.12H2O,以磷酸铵镁沉淀法回收N和P。通过正交实验确定影响磷酸铵镁沉淀反应的因素依次为:pH值、PO34-∶NH4+、Mg2+∶NH4+、温度。在搅拌速度=100 r/min、反应温度=15℃、反应时间=10 min的条件下,实验分别考察了pH值、PO43-投加量、Mg2+投加量对磷酸铵镁沉淀法去除N、P的影响,结果表明最佳工艺条件为pH=9.5,Mg2+∶NH4+∶PO34-=1.3∶1.0∶1.0。最佳工艺条件下尿液中的NH4+-N可从2 850 mg/L降低到约125 mg/L;剩余磷酸盐浓度约7 mg/L。SEM及XRD分析表明,沉淀物的主要成分为呈斜方晶系的磷酸铵镁晶体。     

磷酸铵镁沉淀法预处理垃圾渗滤液

探讨了用磷酸铵镁沉淀法预处理垃圾渗滤液时,沉淀剂种类、pH值、物质摩尔配比和反应时间等因素对氨氮去除效果的影响。得出了处理氨氮浓度为2 677.34 mg/L的垃圾渗滤液时,在兼顾所用镁盐量尽量低和处理出水氨氮或磷酸盐的残留量都比较低的较佳实验条件为:沉淀剂种类为:MgSO4.7H2O和Na2HPO4.12H2O,反应时间为20 min,pH=9.5,n(Mg)∶n(P)∶n(N)=1.3∶1.15∶1.0。在较佳实验条件下,垃圾渗滤液的NH3-N去除率为97.05%,处理出水PO34--P含量为8.35 mg/L,NH3-N含量为75.86 mg/L。对所得沉淀物进行了成分分析和X-衍射光谱、扫描电镜表征,表明大部分沉淀物为磷酸铵镁物质。     

诱导结晶法去除地下水中氟离子

针对现行高氟地下水处理工艺中存在的工艺复杂、运行管理困难等问题,提出采用诱导结晶法除氟。其技术核心是在高氟水中投加氟磷灰石作为晶种,并投加磷酸盐和钙盐使水中氟离子在晶种表面生成氟磷酸钙(Ca10(PO4)6F2)结晶。通过单因素实验得出最佳工艺条件:投加8g/L氟磷灰石,并投加NaH2PO4和CaCl2,使钙离子、磷酸根离子和氟离子的摩尔比为10∶5∶1,搅拌速度为100 r/min,反应时间1 h。反应中磷酸根离子和钙离子的利用率分别达到98%和25%以上。电子扫描显微镜(SEM)表征晶种在参与反应后,表面有结晶生成。研究表明,采用诱导结晶法可将水中氟离子浓度从5~10 mg/L降至1 mg/L以下,达到饮用水水质标准。     

基于响应面法优化MAP法处理垃圾渗滤液工艺的研究

利用单因素实验以及响应面法(response surface methodology,RSM),对磷酸铵镁法(magnesium ammonium phosphate,MAP)去除垃圾渗滤液氨氮的影响因素进行了分析和探讨。考察了pH值为8.0～11.0、n(Mg)∶n(N)摩尔比为0.8～1.6、n(P)∶n(N)摩尔比为0.8～1.3条件下,分析氨氮去除率的变化,用Design-Expert软件处理实验数据,得到了二次响应曲面模型以及优化的水平值。基于经济和操作简便性的考虑,pH值由优化水平的8.3调整为9.5,n(Mg)∶n(N)、n(P)∶n(N)摩尔比取优化水平分别为1.40、1.19,氨氮去除率平均值为92.2%,虽然该条件比最佳条件下的氨氮去除率降低了2个百分点,但从操作的难易程度以及经济性方面,体现了其优势。通过X衍射与电镜扫描分析沉淀物质的成分与晶形,表明大部分沉淀物质为磷酸铵镁。     

诱导结晶法去除地下水中氟离子简

针对现行高氟地下水处理工艺中存在的工艺复杂、运行管理困难等问题,提出采用诱导结晶法除氟。其技术核心是在高氟水中投加氟磷灰石作为晶种,并投加磷酸盐和钙盐使水中氟离子在晶种表面生成氟磷酸钙（Ca₁₀（PO₄） ₆F₂）结晶。通过单因素实验得出最佳工艺条件：投加8g/L氟磷灰石,并投加NaH₂PO₄和CaCl₂,使钙离子、磷酸根离子和氟离子的摩尔比为10：5：1,搅拌速度为100 r/min,反应时间1 h。反应中磷酸根离子和钙离子的利用率分别达到98%和25%以上。电子扫描显微镜（SEM）表征晶种在参与反应后,表面有结晶生成。研究表明,采用诱导结晶法可将水中氟离子浓度从5~10 mg/L降至1 mg/L以下,达到饮用水水质标准。     

镁铝类水滑石原位共沉淀法处理含镍模拟废水的研究

通过原位共沉淀法处理含镍模拟废水,探讨了反应时间、体系pH、镍与镁的摩尔比(Ni/Mg)、二价离子与三价离子的摩尔比((Ni+Mg)/Al)和Ni 2+初始浓度对Ni 2+去除效果的影响。实验结果表明,Ni 2+能通过镁铝类水滑石原位共沉淀法被除去。体系pH、Ni/Mg、(Ni+Mg)/Al和Ni 2+初始浓度均对Ni 2+去除率影响较大,而反应时间对其影响不大。在反应时间为1～2h、pH=8.5、Ni/Mg=0.25、(Ni+Mg)/Al=2.0时,可获得最高的Ni 2+去除率(99.84%),产物经X射线衍射(XRD)分析确定具有层状双氢氧化物(LDHs)结构。     

混凝-热处理联合MAP法处理高浓度水性油墨印花废水

采用混凝-热处理联合磷酸铵镁沉淀法(MAP)处理高浓度水性油墨印花废水,研究了各工艺参数对该废水处理效果的影响。研究表明:混凝-热处理可降低废水的COD和色度,实现固液快速分离,有效降低混凝污泥含水率;MAP法可有效降低混凝-热处理后废水的氨氮含量,药剂摩尔比和反应体系pH对氨氮去除效果影响较大。当投加15 m L·L~(-1)的40%(体积分数)混凝剂NS-1、在70℃下热处理50 min的条件下,废水的COD去除率达到93.65%,色度去除率达到99.97%,而混凝污泥含水率可降到56.62%;向混凝-热处理后废水中投加硫酸镁和磷酸氢二钠,当药剂摩尔比为1.1:0.9:1(Mg:P:N)、体系pH为9.5、在20℃反应30 min的条件下,废水的氨氮去除率可达96.27%,剩余总磷低于12 mg·L~(-1)。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.