纳米TiO2/活性炭复合光催化剂的制备及其对甲醛气体降解

研究了纳米TiO2/活性炭复合光催化剂对空气中典型污染气体甲醛的光催化降解特性。采用扫描电镜（SEM）表征复合催化剂的表面特征。结果显示,经改性后的纳米TiO2在复合催化剂表面分布均匀,呈球状。对甲醛气体的降解实验显示TiO2负载量为1%时对甲醛的去除效果最好,6 h去除率为61.7%。结果显示复合催化剂把甲醛气体分解成CO2,可以直接排空,无二次污染。     

活性炭纤维负载TiO2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响。结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%。     

活性炭纤维负载TiO_2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响.结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%.     

模拟室内环境下掺杂TiO2纳米晶体的光催化性能

采用环境测试舱模拟可见光下的室内环境,以甲醛气体的光催化降解为探针反应,评价了通过溶胶-凝胶法分别制备的8种(银Ag、铜Cu、铁Fe、钨W、铈Ce、镧La、硫S和氯C1)掺杂TiO2纳米晶体的光催化活性及对甲醛气体的去除效果.用X射线衍射、激光粒度分析和紫外-可见分光光谱表征了掺杂钠米TiO2的微晶尺寸、晶体结构与光学性能.结果表明,Cu掺杂可以提高TiO2对氧的吸附能力,减少纳米粒子表面光生电子与光生空穴的复合,使TiO2的光吸收带边发生红移且有利于对可见光的吸收,从而使Cu掺杂TiO2在模拟室内环境下光催化甲醛气体的能力得到明显提高.     

纳米生态建筑涂料光催化降解甲醛的研究

以掺加纳米TiO2制备的光催化建筑涂料为催化剂,研究了在紫外光照条件下对气态甲醛的催化降解,并探讨了纳米催化剂晶型、用量和吸附量对光催化降解甲醛的影响。实验结果表明,锐钛型纳米TiO2具有较高的光催化降解甲醛的活性,1h甲醛的降解率可达到70％左右,产物主要为二氧化碳和水;光催化降解甲醛受到涂膜上吸附量的较大影响;该涂料对甲醛的光催化降解反应表现出一级动力学速率规律,且具有良好的线性关系。     

泡沫镍负载改性TiO_2降解甲醛

为了消除甲醛气体对人类的危害,对甲醛气体的光催化降解行为进行了研究。采用沉淀-胶溶法制得了具可见光活性的纳米TiO2溶胶,然后将其负载于经过预处理的泡沫镍板上,置于自置的光催化反应器中,考察了在可见光照射下对密闭空间里面一定浓度的甲醛气体的降解情况。采用乙酰丙酮分光光度法,在最佳的检测条件下检测气相中甲醛气体经不同光照时间后的浓度。研究发现,负载了氮掺杂改性的TiO2的泡沫镍板在可见光照射下能够有效降解气相中的甲醛,反应240 min后对甲醛气体的降解率为93%;而同样条件下反应器中只有处理过的泡沫镍板时,甲醛气体浓度基本保持不变。     

模拟室内环境下掺杂TiO_2纳米晶体的光催化性能

采用环境测试舱模拟可见光下的室内环境,以甲醛气体的光催化降解为探针反应,评价了通过溶胶-凝胶法分别制备的8种（银Ag、铜Cu、铁Fe、钨W、铈Ce、镧La、硫S和氯C l）掺杂TiO2纳米晶体的光催化活性及对甲醛气体的去除效果。用X射线衍射、激光粒度分析和紫外-可见分光光谱表征了掺杂钠米TiO2的微晶尺寸、晶体结构与光学性能。结果表明,Cu掺杂可以提高TiO2对氧的吸附能力,减少纳米粒子表面光生电子与光生空穴的复合,使TiO2的光吸收带边发生红移且有利于对可见光的吸收,从而使Cu掺杂TiO2在模拟室内环境下光催化甲醛气体的能力得到明显提高。     

Fe_3O_4@SiO_2/TiO_2核壳结构纳米颗粒降解TNT溶液

针对TNT炸药废水具有成分复杂、排放量大、有毒等特点,立足于炸药废水在排放前的降解处理,研究开发一种基于核壳结构Fe3O4@SiO2/TiO2纳米颗粒的高效、可控回收、无二次污染且成本低的光催化降解方法。利用高温碳还原法和溶胶凝胶法制备了具有核壳结构的Fe3O4@SiO2/TiO2纳米颗粒。XRD分析表明,内核Fe3O4呈现磁铁矿特征,表面覆盖的纳米TiO2为锐钛矿型。磁滞回线测试结果显示,复合颗粒的饱和磁化强度为46.5 emu/g,N2吸附-解吸分析结果表明,该颗粒具有典型的介孔结构。使用Fe3O4@SiO2/TiO2纳米颗粒在紫外光下对含TNT废水进行降解,降解率达到81.9%,且颗粒的回收率达到88.4%,为实现高效、可控回收、无二次污染光催化-吸附降解TNT奠定了基础。     

纳米TiO2/硅藻土光催化降解废水中二甲胺

通过凝胶-溶胶法制备纳米TiO2/硅藻土复合催化剂,对常见工业难降解有机污染物二甲胺(DMA)进行了降解实验.采用扫描电镜和X射线衍射技术对催化剂能进行了表征,考察了废水初始浓度、pH、催化剂用量、外加氧化剂对DMA光催化降解效果的影响,进行了降解动力学和降解机理的分析.结果表明,所制催化剂为锐钛矿和金红石混合晶型,均达纳米级,对中低浓度(≤400 mg/L)DMA废水具有良好的降解效果.常温常压、18W紫外汞灯下,3 g/L TiO2/硅藻土对DMA废水(400 mg/L)降解率可达70％以上;其降解反应符合Langmuir-Hinshelwood动力学模型;其可能的降解途径为:二甲胺(DMA)→甲胺(MA)→CO2/CO32-、H2O和NH4+.     

活性炭纤维负载TiO2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO₂作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO₂催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响。结果表明,活性炭纤维与TiO₂的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO₂溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37％;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%。     

CdS-TiO_2/MWCNTs结构表征及其光催化性能

采用溶胶-凝胶法,制备了多壁碳纳米管(MWCNTs)负载的双组分复合半导体光催化剂CdS-TiO2/MWCNTs。通过透射电镜(TEM)、比表面分析(BET)、X射线衍射(XRD)和紫外-可见吸收光谱(UV-vis)等分析方法对光催化剂进行了结构表征,并考察了CdS-TiO2/MWCNTs对甲苯降解的光催化性能。结果表明:纳米活性粒子CdS-TiO2均匀负载于MWCNTs上,比表面积、光吸收阈值和强度增大,活性粒子间以及活性粒子与载体之间具有协同作用,有利于光催化性能的提高,CdS-TiO2/MWCNTs在主波长为254 nm紫外光照射下对甲苯的降解效果较好,去除率可达55.3%。     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶凝胶法制备TiO₂/beads光催化剂载体,然后浸渍法制备出H₄SiW₁₂O₄₀/TiO₂/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H₄SiW₁₂O₄₀/TiO₂/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明,在中性条件下,H₄SiW₁₂O₄₀/TiO₂/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

CuO/TiO2-H2O2可见光催化亚甲基蓝脱色效果及影响因素研究

以水解法制备的锐钛矿型TiO2为载体,制备了CuO/TiO2型光催化剂.以亚甲基蓝为对象,在可见光照射下研究了H2O3加入量、pH值和催化剂投加量对脱色效果的影响,同时与改性前的TiO2催化剂进行了脱色效果的对比.结果表明亚甲基蓝在碱性条件下能较好脱色,H2O2用量和CuO/TiO2催化剂投加量分别为每1 000 mL反应液各加入10 mL和0.1 g时脱色最好;另外,TiO2催化剂也在碱性条件下能较好脱色,H2O2用量和催化剂投加量分别为每1 000 mL反应液各加入12.5 mL和0.1 g时脱色最好.最优条件下对比实验表明,CuO/TiO2型催化剂在可见光照射下具有很高的催化活性,亚甲基蓝2 h脱色率达到88%,远好于改性前的TiO2和Degussa P25催化剂.     

Photodegradation of perfluorooctanoic acid by synthesized TiO2-MWCNT composites under 365nm UV irradiation

Degradation of perfluorooctanoic acid (PFOA) is of great importance due to its global distribution, persistence and toxicity to bioorganisms. In present study, a composite TiO₂ with multiple wall carbon nano-tubes (MWCNTs) was synthesized using sol-gel method and it was used as photocatalyst to degrade PFOA in water. The prepared composite catalyst displayed significant absorption in UV to visible light region. The loading content of TiO₂ on MWCNTs could be adjusted by changing the ratio of precursor to MWCNTs. Due to the combined effect of the adsorption ability and e⁻ transport capacity of MWCNT, the composites displayed much higher photocatalytic ability to PFOA as compared to pure TiO₂ under UV irradiation. The photocatalyst prepared with 10:1 of tetrabutyl titanate/MWCNT was the most effective. With the optimal dosage at 1.6 g L⁻¹, almost 100% of PFOA was degraded in acid medium after irradiation for 8 h. It was proposed that PFOA were mainly degraded by stepwise losing a moiety of CF₂.     

Photocatalytic degradation of gaseous toluene over Ag-doping TiO₂ nanotube powder prepared by anodization coupled with impregnation method

In this work, Ag-doping TiO₂ nanotubes were prepared and employed as the photocatalyst for the degradation of toluene. The TiO₂ nanotube powder was produced by the rapid-breakdown potentiostatic anodization of Ti foil in chloride-containing electrolytes, and then doped with Ag through an incipient wetness impregnation method. The samples were characterized by scanning electron microscope, high-resolution transmission electron microscopy, X-ray diffraction, surface photovoltage measurements, X-ray photoelectron spectroscopy and N₂ adsorption. The nanotubular TiO₂ photocatalysts showed an outer diameter of approximately 40 nm, fine mesoporous structure and high specific surface area. The photocatalytic activity of Ag-doping TiO₂ nanotube powder was evaluated through photooxidation of gaseous toluene. The results indicated that the degradation efficiency of toluene could get 98% after 4 h reaction using the Ag-doping TiO₂ nanotubes as the photocatalyst under UV light illumination, which was higher than that of the pure TiO₂ nanotubes, Ag-doping P25 or P25. Benzaldehyde species could be observed during the photocatalytic oxidation monitored by in situ FTIR, and the formed benzaldehyde intermediate during reaction would be partially oxidized into CO₂ and H₂O.     

Carbofuran removal in continuous-photocatalytic reactor: Reactor optimization,rate-constant determination and carbofuran degradation pathway analysis

Carbofuran (CBF) removal in a continuous-flow photocatalytic reactor with granular activated carbon supported titanium dioxide (GAC-TiO₂) catalyst was investigated. The effects of feed flow rate, TiO₂ concentration and addition of supplementary oxidants on CBF removal were investigated. The central composite design (CCD) was used to design the experiments and to estimate the effects of feed flow rate and TiO₂ concentration on CBF removal. The outcome of CCD experiments demonstrated that reactor performance was influenced mainly by feed flow rate compared to TiO₂ concentration. A second-order polynomial model developed based on CCD experiments fitted the experimental data with good correlation (R² ～ 0.964). The addition of 1 mL min^?1 hydrogen peroxide has shown complete CBF degradation and 76% chemical oxygen demand removal under the following operating conditions of CBF ～50 mg L^?1, TiO₂ ～5 mg L^?1 and feed flow rate ～82.5 mL min^?1. Rate constant of the photodegradation process was also calculated by applying the kinetic data in pseudo-first-order kinetics. Four major degradation intermediates of CBF were identified using GC-MS analysis. As a whole, the reactor system and GAC-TiO₂ catalyst used could be constructive in cost-effective CBF removal with no impact to receiving environment through getaway of photocatalyst.     

碳纳米管/二氧化钛/壳聚糖催化薄膜光催化活性及苯降解机理

通过X-射线衍射仪(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外可见光漫反射谱(UV-vis)对碳纳米管/二氧化钛/壳聚糖复合薄膜的晶体结构和形貌进行表征,以室内空气典型污染物气相苯为模型反应物,研究碳纳米管/二氧化钛/壳聚糖催化薄膜的光催化活性及其对苯的光降解机理。结果表明,制备的碳纳米管/二氧化钛/壳聚糖催化薄膜所具有的良好催化活性归功于碳纳米管、二氧化钛和壳聚糖三者的协调效应;气相苯光降解产生的主要中间产物是乙酸乙酯和十一烷,以及少量的丙烯醛、4-羰基-甲基-苯乙酮、十二烷烃、2,4,-二叔丁基苯酚、二十一烷烃。根据红外光谱分析与GC/MS分析结果,进一步提出了气相苯的降解机理过程。     

纳米Bi2O3/TiO2复合光催化剂的制备及性能研究

以光催化效果为评价标准,采用超声波作用下水解法制备Bi₂O₃/TiO₂复合光催化剂,考察了水解条件和Bi₂O₃掺入量等制备条件对复合光催化剂性能的影响。结果表明,与传统制备方法相比,该方法操作简单、快速;当水和乙醇的比例为4∶1时所得样品的光催化活性最好;Bi₂O₃的掺入拓宽了TiO₂对光的吸收范围,提高了TiO₂的光催化活性,掺入量(Bi₂O₃)为0.25%复合光催化剂催化活性最高;复合光催化剂对多种水溶性染料均具有较好的处理效果。