Fenton氧化法对磺胺类抗生素的降解动力学

采用Fenton氧化法同时降解水溶液中磺胺吡啶(SPY)、磺胺二甲基嘧啶(SMZ)和磺胺甲噁唑(SMX)。系统考查了初始H2O2浓度、Fe2+浓度、pH对3种磺胺类抗生素降解性能的影响。结果表明,3种磺胺抗生素被完全降解的最佳Fenton氧化条件是:H2O2浓度为2.0 mmol/L,Fe2+浓度为0.10 mmol/L,pH为3.0~3.5,反应时间为20 min。Fenton试剂对3种磺胺类抗生素的降解符合一级反应动力学,速度常数为0.0318~0.2002 min-1。     

Fenton试剂处理腐殖酸废水影响特性和降解动力学模型

研究了Fenton试剂降解腐殖酸废水的影响特性,并在理论分析反应过程的基础上建立动力学方程,同时根据实验进行动力学方程参数估算。研究表明,Fenton试剂通过氧化和混凝共同作用有效去除腐殖酸。在初始pH=4,40mmol/L FeSO4和160 mmol/L H2O2投量下,腐殖酸60 min氧化去除率、混凝去除率分别达到78.6%和11.5%,其初始氧化速率达到最大59.6 mg/(L.min)。腐殖酸的氧化降解动力学模型值与实验值吻合良好,说明采用该动力学模型能较好预测腐殖酸废水的氧化降解情况,且Fenton氧化降解腐殖酸的机理符合自由基的理论和实践。     

Fenton氧化降解垃圾渗滤液中COD的动力学研究

对絮凝预处理后的垃圾渗滤液进行Fenton氧化处理。通过微分法对Fenton氧化的反应级数进行求解,确定其反应级数为2,并初步建立了Fenton氧化的动力学模型,即1/c=1/c0+kt,由此建立起来的降解的动力学模型与实验数据相吻合;在4个实验基准条件下———初始COD浓度为960 mg/L、pH值4、H2O2投加量0.4 mol/L、nH2O2/nFe2+3∶1,探讨了其中某一变量对反应速率的影响。实验水样为絮凝反应出水,进水COD浓度为912～960 mg/L,出水COD浓度为80～112 mg/L,COD去除率在87%～92%之间,表明Fenton试剂能够有效地处理垃圾渗滤液。     

光助Fenton氧化法降解水中六氯苯的研究

采用光助Fenton氧化法处理六氯苯模拟废水,考察了反应时间、Fe3 与H2O2摩尔比、Fenton试剂用量、初始pH、六氯苯初始浓度、光强对六氯苯降解效果的影响,并初步探讨了六氯苯的降解动力学规律.结果表明.光助Fenton法降解六氯苯的最佳工艺条件为:紫外灯功率为300 W、Fe3 投加量为1.0 mmol/L、H2O2投加量为5.0 mmol/L、反应时间为60 min、初始pH为3,在此条件下,浓度为500μg/L的HCB的去除率可达91.3%.UV辐射与Fenton氧化对HCB的降解具有协同效应.光助Fenton法对HCB的降解符合一级反应动力学方程,表观速率常数为0.04 min-1,与Fenton法相比,提高了近9倍.     

Fenton氧化水中间氯硝基苯的动力学与机制研究

结合Fenton氧化反应动力学模型研究了Fenton氧化水中间氯硝基苯(m-ClNB)的影响因素和降解机制.结果表明:(1)反应初始pH、H2O2浓度、Fe2+浓度、污染物初始浓度和反应温度对m-ClNB的降解均有明显影响.在反应初始pH为3.5、m-ClNB初始摩尔浓度为0.444mmol/L、H2O2摩尔浓度为21.55mmol/L、Fe2+摩尔浓度为0.054mmol/L、反应温度为(25土1)℃的条件下,m-ClNB的去除效果较好.(2)建立了Fenton氧化m-ClNB的准一级反应动力学模型,且m-ClNB的降解与该模型拟合良好.基于不同反应温度时的准一级反应速率常数(kap),得到了m-ClNB降解的阿累尼乌斯公式,且活化能为36.51kJ/mol.(3)气相色谱(GC)/质谱(MS)和高效液相色谱(HPLC)/MS分析表明,Fenton氧化m-ClNB的主要产物有4-氯-2-硝基苯酚及其同分异构体、羟基乙酸、草酸、丁二酸、丙二酸、6-氯己酸、乙醛酸、2,2-二羟基丙二酸和2-乙基丙二酸等.     

UV/Fenton法处理酸性红B研究

采用UV/Fenton高级氧化技术对酸性红B模拟废水进行处理,当进水浓度为400mg/L时,确定了各影响因素的最佳投加量:H2O2投加量为2 mL/L,Fe2 投加量为0.08g/L,最佳pH值为4;并采用一级动力学公式对酸性红B降解速率进行拟合,研究了反应条件对速率常数的影响.最后通过对单独UV法、单独Fenton法和UV/Fenton法3种处理方法效果的比较,发现UV与Fenton试剂具有协同作用.     

Fenton法处理垃圾渗滤液的参数优化及反应动力学模型

采用Fenton法处理垃圾渗滤液,研究反应时间、初始浓度、pH、Fenton试剂用量对垃圾渗滤液TOC去除率的影响。研究结果表明,最优反应条件是反应时间30 min,初始pH为3.0,初始[H2O2]0=7 310 mg/L,最佳[H2O2]/[Fe2+]摩尔比为5,反应温度为室温,此时渗滤液的TOC去除率达到70.3%。渗滤液矿化过程符合一级反应动力学,并建立了符合该渗滤液的反应动力学模型。     

非均相UV/Fenton氧化法降解水中六氯苯的研究

采用超声辐照促进浸渍法制备了非均相UV/Fenton催化剂Fe/Al2O3,并对其进行了表征.以制备的催化剂对水中六氯苯进行非均相UV/Fenton法氧化降解.考察了铁的负载量、初始pH、H2O2投加量、催化剂投加量和反应时间对六氯苯降解效果的影响,并探讨了六氯苯的降解动力学规律.结果表明,制备的催化剂表面活性组分分散均匀,对六氯苯具有较高的催化活性和重复利用性.非均相UV/Fenton法降解六氯苯的最佳实验条件为:铁的负载量为2%,废水初始pH为3,H2O2和Fe/Al2O3催化剂的投加量分别为34 mg/L和150 mg/L,反应时间为20 min.在此条件下,浓度为500μg/L的六氯苯降解效率达94.5%.HCB的降解反应动力学规律可用Langmuir-Hinshwood方程很好地描述.六氯苯在催化剂表面的吸附常数为1.962 L/mg,表面反应速率常数为0.08 mg/(L·min).     

Fenton氧化法深度处理丙烯腈废水的研究

以丙烯腈(AN)废水为研究对象,在正交实验基础上深入研究了Fenton反应体系中pH值、Fe2+浓度、H2O2浓度、温度、UV和C2O2-4对降解效果的影响,分析了不同因素作用机理,确定了最佳操作条件pH=3、[Fe2+]=400mg/L、[H2O2]=400mg/L、反应温度40℃,在此条件下丙烯腈降解率达80%以上。同时发现在紫外光、C2O2-4对Fenton试剂的协同作用下,降解率可提高10%左右。     

UV/Fenton法预处理橡胶促进剂生产废水

采用UV/Fenton法对橡胶促进剂废水进行预处理.当原水COD约为3000 mg/L时,COD去除率可达65%以上,并得到最佳操作条件为:H2O2投加量为8 mL/L,Fe2 投加量为0.8 g/L,反应时间为30 min,pH=5;同时得到Fenton试剂处理该废水的最佳条件为:H2O2投加量为10 mL/L,Fe2 投加量为0.966 g/L,反应时间为30 min,pH=5;单独UV作用的最佳工艺条件为:反应时间为20 min,pH=5;并就3种处理方法进行了比较,发现UV对Fenton试剂处理橡胶促进剂废水具有一定促进作用.反应前后的紫外光谱说明,经UV/Fenton或Fenton反应后原水中的苯胺、硝基苯等物质已得到了彻底的氧化分解.     

Use of diffuse reflectance spectrometry in spot test reactions for quantitative determination of cations in water

Diffuse reflectance spectroscopy can be successfully used for the quantitative determination of small amounts of pollutants like metals. The remission function was found to be linearly proportional to the concentration, when we applied the Kubelka–Munk equation. The color reactions of Cu(II), Co(II), and Ni(II) with dithiooxamide, were realised on filter paper. Reaction between Fe(III) and ammonium thiocyanate was realized on filter paper and gelatine matrix. All measurements were accomplished with a laboratory-constructed reflectometer. We have obtained a calibration curve by plotting the optical density of reflectance A_R vs log of the mol l⁻¹ concentration. Limits of detection at the 10⁻⁴ M level were estimated for all the compounds. Linear dynamic range extend over one order of magnitude and shows the potential of device for the quantitative analysis of environmental pollutants.     

Distribution and sources of polyfluoroalkyl substances (PFAS) in the River Rhine watershed

The concentration profile of 40 polyfluoroalkyl substances (PFAS) in surface water along the River Rhine watershed from the Lake Constance to the North Sea was investigated. The aim of the study was to investigate the influence of point as well as diffuse sources, to estimate fluxes of PFAS into the North Sea and to identify replacement compounds of perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA). In addition, an interlaboratory comparison of the method performance was conducted. The PFAS pattern was dominated by perfluorobutane sulfonate (PFBS) and perfluorobutanoic acid (PFBA) with concentrations up to 181 ng/L and 335 ng/L, respectively, which originated from industrial point sources. Fluxes of ΣPFAS were estimated to be ∼6 tonnes/year which is much higher than previous estimations. Both, the River Rhine and the River Scheldt, seem to act as important sources of PFAS into the North Sea.     

Polychlorinated dibenzo-p-dioxins and related compounds: the blood levels of young Japanese women.

We investigated PCDDs and related compounds in the blood of young Japanese women, approximately 20 years of age, who had not yet had children, and discussed how the TEQ level of PCDDs and related compounds in their blood may affect the next generation. Means of total TEQ levels were 0.063 pg/g for whole blood basis and 21 pg/g for lipid basis. TEQ of PCDDs, PCDFs and coplanar PCBs accounted for about 43, 34 and 23% of the total TEQ in the whole blood basis, respectively. In the lipid basis, their values were about 44, 34 and 22%, respectively. Previously, we investigated PCDDs and related compounds levels in mother's breast milk, lymphocyte subpopulation and thyroid function of their children, and found negative correlations between the TEQ level of PCDDs and related compounds and CD4+/CD8+, and/or the TEQ level of PCDDs and related compounds and the T₄ level in 36 mothers and children. Of these cases, the average age was approximately 28 years. PCDDs and related compounds may be related to immunopathy, such as atopic dermatitis. The effects of PCDDs and related compounds on babies of young Japanese women are important and must be further evaluated.     

Effect of vegetation in pilot-scale horizontal subsurface flow constructed wetlands treating sulphate rich groundwater contaminated with a low and high chlorinated hydrocarbon

In order to characterize the effect of vegetation on performance of constructed wetlands (CWs) treating low and high chlorinated hydrocarbon, two pilot-scale horizontal subsurface flow (HSSF) CWs (planted with Phragmites australis and unplanted) treating sulphate rich groundwater contaminated with MCB (monochlorobenzene, as a low chlorinated hydrocarbon), (about 10 mg L⁻¹), and PCE (perchloroethylene, as a high chlorinated hydrocarbon), (about 2 mg L⁻¹), were examined. With mean MCB inflow load of 299 mg m⁻² d⁻¹, the removal rate was 58 and 208 mg m⁻² d⁻¹ in the unplanted and planted wetland, respectively, after 4 m from the inlet. PCE was almost completely removed in both wetlands with mean inflow load of 49 mg m⁻² d⁻¹. However, toxic metabolites cis-1,2-DCE (dichloroethene) and VC (vinyl chloride) accumulated in the unplanted wetland; up to 70% and 25% of PCE was dechlorinated to cis-1,2-DCE and VC after 4 m from the inlet, respectively. Because of high sulphate concentration (around 850 mg L⁻¹) in the groundwater, the plant derived organic carbon caused sulphide formation (up to 15 mg L⁻¹) in the planted wetland, which impaired the MCB removal but not statistically significant. The results showed significant enhancement of vegetation on the removal of the low chlorinated hydrocarbon MCB, which is probably due to the fact that aerobic MCB degraders are benefited from the oxygen released by plant roots. Vegetation also stimulated completely dechlorination of PCE due to plant derived organic carbon, which is potentially to provide electron donor for dechlorination process. The plant derived organic carbon also stimulated dissimilatory sulphate reduction, which subsequently have negative effect on MCB removal.     

BAT and BEP as instruments for reducing emissions of unintentionally produced POPs and development of guidelines under the stockholm convention

The 6th Intergovernmental Negotiating Committee (INC 6), under the Stockholm Convention on POPs, gave an expert group the mandate to develop guidelines for the application and implementation of best available techniques (BAT) and best environmental practices (BEP) for the prevention and reduction of unintentionally produced and emitted POPs, including polychlorinated dibenzodioxins/-furans (PCDD/Fs), polychlorinated biphenyls (PCBs) and hexachlorobenzene (HCB). Measures to reduce or eliminate the release of these POPs to the environment can be found in Article 5 of the Convention. BAT and BEP are already being applied as emission reduction instruments in a number of industrialised countries and are elements of other major international treaties, e.g. the UN ECE Protocol on POPs and the Marine Convention's OSPAR and HELCOM, and of the EU Directive for Integrated Pollution Prevention and Control (IPPC Directive). Existing concepts are presented and compared with the requirements of the Stockholm Convention. Consequences, perspectives and questions for the future intersessional work of the above-mentioned Expert Group are discussed.     

Reduction in uptake by rice and soybean of aromatic arsenicals from diphenylarsinic acid contaminated soil amended with activated charcoal

Activated charcoal (AC) amendment has been suggested as a promising method to immobilize organic contaminants in soil. We performed pot experiments with rice and soybean grown in agricultural soil polluted by aromatic arsenicals (AAs). The most abundant AA in rice grains and soybean seeds was methylphenylarsinic acid (MPAA). MPAA concentration in rice grains was significantly reduced to 2% and 3% in 0.2% AC treated soil compared to untreated soil in the first year of rice cultivation. In the second year, MPAA concentration in rice grains was significantly reduced to 15% in 0.2% AC treated soil compared to untreated soil. MPAA concentration in soybean seeds was significantly reduced to 44% in 0.2% AC treated soil compared to untreated soil. AC amendment was effective in reducing AAs in rice and soybean.     

Natural attenuation of trichloroethene and its degradation products at a lake-shore site

Subsurface contamination by trichloroethene (TCE) was detected at a Michigan National Priorities List (NPL) site in 1982. The TCE plume resulted from the disposal of spent solvent and other chemicals at an industrial facility located in the eastern shore of Lake Michigan. TCE degradation products of three dichloroethene (DCE) isomers, vinyl chloride (VC) and ethene were present. The plume was depleted of oxygen and methanogenic at certain depths. Transects of the plume were sampled by slotted auger borings the year after the TCE plume was first discovered. Water samples were also taken from lake sediments to a depth of 12 m about 100 m offshore. Later samples were taken along the shoreline of the lake with a hand-driven probe. Later in 1998 water was taken from sediments about 3-m from the shoreline. The average concentration of each chemical and net apparent base coefficient between appropriate pairs of transects between the lower site and lakeshore were calculated. Loss rates were then calculated from an analytical solution of the two-dimensional advective-dispersive-reactive transport equation. Net apparent rate coefficients and a set of coupled reaction rate equations were used to extract the apparent loss coefficients. This study showed the field evidence for natural attenuation of TCE.     

Using a Set of Strategic Indicator Systems as a Decision-making Support Implement for Establishing a Recycling-oriented Society - A Taiwanese Case Study (16 pp)

Background Scope and Aims. To realize the vision of sustainable development (SD) originating from the ‘only one earth’ philosophy, and to integrate the conceptions of ecology and sustainability into the planning and decision-making criteria of urban growth management, the establishment of a recycling-oriented society (ROS) is essential. However, before the above intention can be achieved, it is indispensable to develop a system of strategic indicators for supporting a radical reformation of the urban development plan. Therefore, this study, based on the conception of the new urban development pattern ROS, attempted to carefully choose a sample city in Taiwan for launching a preliminary case study, and furthermore designed and proposed a concise and strategy-oriented assessment indicator system termed ROSAIS. ROSAIS, on the one hand, can act as a compass for understanding resource using efficiency and recycling status during city development and, on the other hand, can serve as an implement supporting decision-making for ROS construction.Methods According to the definition and spirit of ROS, the structure of ROSAIS should clearly represent the relationship between resources and environment in human activities. The eco-efficiency indicator system (EEIS) and environmental symbiosis indicator system (ESIS) can be considered two key sub-indicator systems, and are the necessary components of ROSAIS. EEIS chooses the dominant production sectors in urban economic activities to calculate their eco-efficiency (EE). Separately, for obtaining a consensus regarding the framework of ESIS, the questionnaire approaches and expert consultation, together with the research experience and foundation of current relevant studies and indicator systems, are applied when crucial resource and environmental issues and respective indicators are selected.Results and Discussion The calculation results of EEIS in this case study indicated that among the three dominant production activities (agricultural, fishery, and animal husbandry sector) the fishery sector has the highest EE, which indicates that the fishery activities and resources significantly influence the sustainability of the economic-environmental system of the sample city. Furthermore, according to a consensus achieved in ESIS, local green spaces, resource recovery, energy consumption pattern change, freshwater conservation and greenhouse effect abatement were considered as the five crucial issues influencing how the case study city can develop into an ES-city. The rate of local green spaces, resource recycling, freshwater conservation and the rate of reduction of nonrenewable energy use as well as carbon dioxide (CO2) emissions were used to evaluate the above five issues.Conclusion This case study is unparalleled in Taiwan. Even in Japan, where ROS legislation has been implemented, this kind of study remains in the preliminary stages. Furthermore, when communicating the indicator results, it is essential to provide the context and countermeasures of the crucial issues that are faced. The two sub-indicator systems proposed in this case study could comply completely with the above-mentioned requirements. For example, the EEIS provides information for achieving a balance between environmental burden and economic benefits among dominant production sectors; the ESIS provides information for setting strategies for overcoming the crucial issues faced. Recommendation and Outlook This study recommends that urban planers should consider the construction of the corresponding strategic indicator system to be indispensable, and makes further use of the indicator results related to the environmental education of residents for identifying and promoting participation with ROS, and turning them into implements for supporting urban SD decision-making. Furthermore, a successful indicator system depends on data availability and quality. This study recommends that urban planers should pay considerable attention to constructing relevant data collection channels, databases and the data quality.     

Emissions from soil fumigation in two raised bed production systems tarped with low permeability films

Raised beds are used to produce some high-value annual fruit and vegetable crops such as strawberry in California (CA) and tomato in Florida (FL), USA. Pre-plant soil fumigation is an important tool to control soil-borne pests in the raised beds. However, fumigant emissions have detrimental environmental consequences. Field trials were conducted to evaluate emissions of 1,3-dichloropropene (1,3-D) and chloropicrin (CP) in two different production systems with raised beds covered by different tarps. In the CA trial, InLine (60.8% 1,3-D and 33.3% CP) was drip-applied at 340 kg ha⁻¹ to 5 cm deep in the beds (30 cm high and 107 cm wide) tarped with polyethylene (PE) or virtually impermeable film (VIF). In the FL trial, carbonated Telone C35 (63.4% 1,3-D and 34.7% CP) was shank-applied at 151 kg ha⁻¹ to 20 cm deep in the beds (22 cm high and 76 cm wide) tarped with totally impermeable film (TIF). Emissions from tarped beds relative to furrows were contrary between the two trials. For the CA trial, the emission was 47% of applied 1,3-D and 27% of applied CP from PE tarped beds and 31% of applied 1,3-D and 15% of applied CP from VIF tarped beds, while that from uncovered furrows was <0.4% for both chemicals in both fields. In the FL trial, only 0.1% 1,3-D was emitted from the TIF tarped beds, but 27% was measured from the uncovered furrows. Factors contributing to the differences in emissions were chiefly raised-bed configuration, tarp permeability, fumigant application method, soil properties, soil water content, and fumigant carbonation. The results indicate that strategies for emission reduction must consider the differences in agronomic production systems. Modifying raised bed configuration and fumigant application technique in coarse textured soils with TIF tarping can maximize fumigation efficiency and emission reduction.     

机动车尾气中氮氧化物的分析检测技术

为了分析机动车尾气氮氧化物净化催化剂的催化性能 ,建立了一套尾气模拟评价体系 ,分别使用电化学法、化学发光法和比色法 3种氮氧化物分析手段进行检测。结果表明 ,3种方法都能在一定精度范围内测量机动车尾气中的氮氧化物 ,化学发光法测量精度高 ,响应时间短 ,能够及时地反映发动机运转过程中的氮氧化物浓度变化情况 ,是一种较好的分析手段。电化学法随着使用时间推移 ,响应时间变长 ,灵敏度降低 ,需要及时更换传感器。比色法通过化学吸收可以测定氮氧化物的浓度 ,不能实现连续在线分析 ,只能采样测量。在分析中 ,还尝试利用一些辅助设备 ,将尾气中的NO和NO2转化后再通入测量仪器 ,实现测量总氮氧化物或其中某一气体的功能