济南市大气颗粒物主要排放源多环芳烃成分谱研究

根据济南市颗粒物排放源的特点,通过采样分析获取了济南市大气颗粒物排放源(土壤风沙尘、扬尘、煤烟尘、机动车尾气尘)的粒度谱、多环芳烃成分谱,为济南市大气颗粒物中多环芳烃的源解析,提供可靠的基础数据。     

BP网络应用于大气颗粒物的源解析

应用BP网络对大气颗粒物进行源解析,将大气采集样本中的元素含量和大气颗粒物源成分谱构成训练样本集,用BP网络进行训练,由训练好的网络的权值可以计算出大气颗粒物的污染排放源的权重贡献率.将BP源解析法的计算结果与其它源解析法得到的结果比较,表明BP网络应用于大气颗粒物的源解析是可行的.     

机动车排放颗粒物成分谱对比研究

对深圳、无锡、济南和美国EPA建立的机动车排放颗粒物成分谱进行对比研究,建立的成分谱中各组分含量存在较大差别原因为使用了不同的采样方法。     

北京市大气PM10源解析研究

于2004年在北京市定陵、车公庄、古城、亦庄、房山和奥体中心6个采样点采集大气PM10环境样品,针对北京市颗粒物主要排放源采集土壤尘、建筑水泥尘、燃煤等污染源PM10样品,分别对其中的无机元素、离子、有机碳(OC)和元素碳(EC)进行测定。采用代表北京市颗粒物主要排放源PM10组分特征的成分谱,利用CMB受体模型对PM10来源进行解析。结果表明,PM10的最大来源为土壤尘,其它贡献源类依次为燃煤排放、机动车/燃油排放、二次粒子(SO42-、NO3-和NH4 )、建筑水泥尘。污染源贡献具有明显的季节变化,并存在一定的地域变化。     

可吸入颗粒上多环芳烃来源的识别和解析

根据化学质量平衡(CMB)受体模型对安阳市大气颗粒物中多环芳烃进行源解析。测定安阳市非采暖季和采暖季可吸入颗粒物中多环芳烃的浓度,对其污染水平进行比较分析。根据污染源调查结果,确定市区多环芳烃的主要排放源类,并建立相应的源成分谱。应用CMB受体模型解析安阳市可吸入颗粒物中多环芳烃主要来源的分担率。     

长沙市城区施工扬尘和土壤扬尘污染时空特征研究

随着我国城市化的迅速发展,大气污染问题成为影响人们生活幸福感的重要因素之一。施工、裸露地面等引起的扬尘成为城市大气颗粒物污染的主要来源。将GIS方法和原环保部《扬尘源颗粒物排放清单编制技术指南(试行)》推荐的计算方法相结合,估算出2016—2018年长沙市城区施工扬尘源、土壤扬尘源的颗粒物排放量,从时空分布特征与空间自相关等多个方面剖析了扬尘源的颗粒物排放情况。结果表明:长沙市扬尘源沿中心城区向西、北方向辐射,呈现出半圆环形的带状分布,以城乡接合部最为集中；2016—2018年,长沙市城区扬尘源排放量总体呈现逐年递减的变化趋势。研究结果与长沙市城区实际情况基本相符,可为长沙市扬尘污染控制策略的制定提供参考。     

燃煤锅炉湿法脱硫烟气中颗粒物排放特征

选择北京市典型燃煤锅炉进行研究,结果表明:烟气中可凝结颗粒物在总颗粒物中占有较高比例,供热燃煤锅炉总颗粒物排放水平明显高于电厂燃煤锅炉;颗粒物中水溶性离子含量较高,供热燃煤锅炉硫酸根比例尤其显著;烟气总颗粒物中存在大量不稳定的易被氧化的组分;同为燃煤源,不同的烟气净化工艺排放的PM2.5组分特征差异明显;现有标准和技术规范存在不足,无法满足全面、准确监测污染源排放总颗粒物的实际需要。建议建立总颗粒物、可凝结颗粒物的监测技术规范,全面测算燃煤锅炉硫、氮化合物排放情况,科学评估脱硫及脱硝效率。     

在线单颗粒气溶胶质谱在大气重金属铅污染事故中的应用研究

重金属铅由于其对人体健康的影响而广受关注。利用在线单颗粒气溶胶质谱仪对2012年发生在华南地区的一次金属铅污染事故中的含铅颗粒物的质谱特征、粒径分布及排放规律进行了分析。监测发现A、B两个监测点位的含铅颗粒物比例多在夜间或凌晨达到高峰,高峰时刻含铅颗粒物数浓度占比最高可达67%,对比广州市区、鹤山超级站的含铅颗粒物浓度占比,可知该地区含铅颗粒物的污染程度较高。两监测点位的含铅颗粒物质谱特征及粒径分布情况非常相似,可能存在相同的排放源或具有相同的形成机制。质谱中都均含有明显的铅、元素碳、硫、硫酸盐等信号,可能来自于燃煤源的排放。通过进一步对比分析燃煤烟气排放的含铅颗粒物质谱特征,判断其为燃煤源排放。     

桂林市细颗粒物部分典型排放源的粒径谱及成分分析

采用在线单颗粒气溶胶质谱技术源解析方法,对桂林市PM2.5典型排放源的粒径和化学成分进行质谱分析,采集燃煤/燃气源、工业工艺源、扬尘源、油烟源4类共计7个典型排放源。结果表明,桂林市4类排放源细颗粒物的粒径分布为0.25~1.25μm,80%以上的细颗粒分布在0.2~1.0μm的小粒径范围,峰值约0.68μm。细颗粒物离子成分含有Na~+、Mg~+、K~+、NH~+4、Fe~+、Pb~+、Cd~+、V~+、Mn~+、Li~+、Al~+、Ca~+、Cu~+、Zn~+、Cr~+、CN~-、PO_3~-、NO_2~-、NO_3~-、Cl~-、SO_4~(2-)、SiO_3~-等成分,桂林市细颗粒物为元素碳、有机碳元素碳、有机碳、富锰颗粒、富铁颗粒、富钾颗粒、矿物质、左旋葡聚糖以及其他金属等9类。     

秸秆焚烧对哈尔滨市灰霾天气的影响

2015年11月1—4日,哈尔滨市及周边地区发生了连续的灰霾天气,颗粒物浓度急剧升高。污染发生时,监测仪器均布设在哈尔滨市区上风向30 km处(哈尔滨市双城区)并开展了连续96 h的监测分析。综合利用气象观测资料,3D可视激光雷达监测资料及地面空气污染监测资料分析了灰霾天气发生的气象条件和污染边界层特征,根据哈尔滨市双城区大气污染物排放源谱库对主要成分进行来源解析,结合颗粒物质量浓度和气象条件研究了秸秆焚烧对灰霾天气的影响。结果表明,灰霾天气持续期间,夜间生物质燃烧源成为该地区颗粒物的第二大源;秸秆焚烧产生的大气污染物,由于地面长时间静风,污染边界层降低等原因,致使本地污染物累积、不易扩散,加剧了本次污染。     

Metallic components of traffic-induced urban aerosol, their spatial variation, and source apportionment

This study proposes a practical method to estimate elemental composition and distribution in order to attribute source and quantify impacts of aerosol particles at an urban region in Kolkata, India. Twelve-hour total particulates were collected in winter (2005–2006) and analyzed by energy-dispersive X-ray fluorescence technique to determine multi-elemental composition, especially trace metals. The aerosols consist of various elements including K, Ca, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Se, and Pb which exhibit significant concentration at various sites (p?<?0.05). The concentration of different metallic elements were found in the order of Zn ?> ?Pb ?> ?Ni ?> ?Cu ?> ?Cr ?>? Co. Statistical multivariate analysis and correlation matrix analyses were performed for factor identification and consequent source apportionment. Contour profiles demonstrate spatial variation of elemental compositions indicating possible source contribution along with meteorological influences. Spatial differences were clearly most significant for Zn, Ni, Pb, and Cu reflecting the importance of anthropogenic inputs, primarily from automobile sources.     

农产品产地土壤重金属外源污染来源解析及防控策略研究

分析了工业生产排放、污水灌溉、矿产资源开发、农业投入品施用、大气颗粒物降尘及固体废弃物堆放等农产品产地土壤重金属主要外源污染来源,在此基础上构建了包括工业过程源、固定燃烧源、灌溉水源、废弃物堆放源、流动源和农业投入品源的来源清单,并从建立健全源头预防和强化过程控制2个方面,提出了加强农产品产地土壤重金属污染监管的相关建议。     

Source apportionment of personal exposure of fine particulates among school communities in India

Source contribution estimates (SCE) of school community personal Respirable Particulate Matter (RPM) have been investigated. Reported relationships of personal RPM with Ambient-outdoors and indoor RPM levels have given the concept of defining the sources of personal exposure. Ambient-outdoors, indoors, soils and local road- traffic dusts were identified as main routes and principal sources of fine particulates at personal exposure levels. Fifteen subjects (05 from each of three schools) were selected from previous conducted study of interrelationships among classified atmospheric receptors in theses schools located in Bhilai-Durg, District Durg, India. Samples of RPM collected from identified receptors and sources were analyzed for selected chemical constituents and the chemical data has been utilized in preparation of source-receptor profiles. Chemical mass balance (CMB8) model has been used for source apportionment study. Major dominating source is ambient-outdoors in case of school located near to steel plant downwind. Indoors and road-traffic dusts have also played dominating role in case of school located near to National Highways. Indoor ventilation properties have played an important role in source contribution estimates.     

Air pollutants and the characterization of the organic content of aerosol particles in a mixed industrial/semi-rural area in central Italy

Both regulated and unregulated air pollutants were detected during an intensive seasonal sampling campaign in a mixed industrial/semi-rural area on the outskirts of Rome, Italy, at two sites located opposite a hospital waste incinerator, downwind according to the direction of the prevailing local winds. Concentrations of pollutants were significantly lower than in urban atmospheres. The composition of particulate organic material indicated a heavy biogenic impact, accompanied by a lower contribution from petroleum-related processes. Both PAH and nitro-PAH group compositions of particulates were used to assess the nature and relative importance of sources. Both sites showed that different and diffuse sources contributed to local pollution with a significant contribution from traffic, proving that the hospital waste incinerator was not the main pollution source in this area. Among unregulated compounds, a series of positional isomers of nitro-PAHs and other organic compounds associated with particulate matter were investigated. In particular, 1- and 3-nitrophenanthrene identification was carried out, and they proved to be the most abundant nitro-PAHs.     

The distribution of polynuclear aromatic hydrocarbons in ambient air particulates in Singapore

Ambient air particulates were collected using high volume samplers at seven locations throughout Singapore. The particulates were analyzed for eleven polynuclear aromatic hydrocarbons (PAH) using high performance liquid chromatography (HPLC) with fluorescence detection. Several sample preparation techniques were used to determine which method would yield the most PAHs from the bulk sample matrix. PAH profiles (standardised against the concentration of benzo(a)pyrene) were obtained to characterise the different sampling sites chosen.     

对应分析在大气颗粒物源解析中的应用研究

采用对应分析方法定性研究龙岩市大气颗粒物来源问题。结果表明:龙岩市4个监测点位中龙岩市环境监测站的主要污染源为高岭土矿和土壤风沙尘;龙岩学院与闽西职业技术学院的主要污染源为机动车尾气尘、燃煤尘和土壤风沙尘;龙岩师专的主要污染源为燃煤尘、小煤炉尘、水泥成品、水泥厂除尘器集尘和钢铁厂除尘器集尘。该方法能将R型因子分析和Q型因子分析结合起来,综合体现样品和元素之间的关系,为大气颗粒物源解析提供了一种新的途径。     

北京市主要PM10排放源成分谱分析

对北京市土壤尘、道路扬尘、城市扬尘、建筑施工尘、钢铁尘、煤烟尘等主要PM10无组织排放源和固定源进行采样、分析,建立相应的成分谱数据库,通过对其化学组分分析,确定各类PM10排放源的化学组分特征和标识元素。土壤尘、建筑施工扬尘、钢铁尘、煤烟尘PM10的标识元素分别为Si、Ca、Fe、Al,道路扬尘显示出明显的土壤尘、建筑施工尘和机动车污染的特征,城市扬尘成分谱与道路尘有很强的共线性,具有明显的道路扬尘特征。     

空气颗粒物中铅、镉超声浸取-原子吸收测定方法研究

用超声波震荡方法对大气滤膜样品进行前处理,提取待测元素。研究了浸取液种类、酸度、浸取时间和干扰因素等,确定了颗粒物样品溶液制备的最佳条件,与流动注射在线富集——原子吸收技术结合,建立了大气颗粒物样品测定Pb、Cd方法。结果表明,方法快速、准确,标准样品测定回收率在97％以上,6次测定方目对标准偏差小于2.6％。     

Evolving Pb isotope signatures of London airborne particulate matter (PM 10)-constraints from on-filter and solution-mode MC-ICP-MS

Pb isotope compositions of biologically significant PM(10) atmospheric particulates from a busy roadside location in London UK were measured using solution- and laser ablation-mode MC-ICP-MS. The solution-mode data for PM(10) sampled between 1998-2001 document a dramatic shift to increasingly radiogenic compositions as leaded petrol was phased out. LA-MC-ICP-MS isotope analysis, piloted on a subset of the available samples, is shown to be a potential reconnaissance analytical technique. PM(10) particles trapped on quartz filters were liberated from the filter surface, without ablating the filter substrate, using a 266 nm UV laser and a dynamic, large diameter, low-fluence ablation protocol. The Pb isotope evolution noted in the London data set obtained by both analytical protocols is similar to that observed elsewhere in Western Europe following leaded petrol elimination. The data therefore provide important baseline isotope composition information useful for continued UK atmospheric monitoring through the early 21(st) century.