A natural analogue for CO2 mineral sequestration in Miocene basalt in the Kuanhsi-Chutung area, Northwestern Taiwan

In general, CO₂ sequestration by carbonation is estimated by laboratory experimentation and geochemical simulation. In this study, however, estimation is based on a natural analogue study of the Miocene basalt in the Kuanhsi-Chutung area, Northwestern Taiwan. This region has great potential in terms of geological and geochemical environments for CO₂ sequestration. Outcropping Miocene basalt in the study area shows extensive serpentinization and carbonation. The carbon stable isotopes of carbonates lie on the depleted side of the Lohmann meteoric calcite line, which demonstrates that the carbonates most probably precipitate directly from meteoric fluid, and water–rock interaction is less involved in the carbonation process. Oxygen stable isotope examinations also show much depleted ratios, representative of product formation under low temperatures (∼50–90 °C). This translates to a depth of 1–2 km, which is a practical depth for a CO₂ sequestration reservoir. According to petrographic observation and electron microprobe analysis, the diopside grains in the basalt are resistant to serpentinization and carbonation; therefore, the fluid causing alteration is likely enriched with calcium and there must be additional sources of calcium for carbon mineralization. These derived geochemical properties of the fluid support the late Miocene sandstone and enclosed basalts as having high potential for being a CO₂ sequestration reservoir. Moreover, the existing geochemical environments allow for mineralogical assemblages of ultramafic xenoliths, indicating that forsterite, orthopyroxene and feldspar minerals are readily replaced by carbonates. Based on the mineral transformation in xenoliths, the capacity of CO₂ mineral sequestration of the Miocene basalt is semi-quantitatively estimated at 94.15 kg CO₂ chemically trapped per 1 m³ basalt. With this value, total CO₂ sequestration capacity can be evaluated by a geophysical survey of the amount of viable Miocene basalt at the potential sites. Such a survey is required in the near future.     

The influence of the precursor and synthesis method on the CO2 capture capacity of carpet waste-based sorbents

Adsorption is one of the most promising technologies for reducing CO₂ emissions and at present several different types of sorbents are being investigated. The use of sorbents obtained from low-cost and abundant precursors (i.e. solid wastes) appears an attractive strategy to adopt because it will contribute to a reduction not only in operational costs but also in the amount of waste that is dumped and burned in landfills every year. Following on from previous studies by the authors, in this work several carbon-based adsorbents were developed from different carpet wastes (pre-consumer and post-consumer wastes) by chemical activation with KOH at various activation temperatures (600–900 °C) and KOH:char impregnation ratios (0.5:1 to 4:1). The prepared materials were characterised by chemical analysis and gas adsorption (N₂, −196 °C; CO₂, 0 °C), and tested for CO₂ adsorption at temperatures of 25 and 100 °C. It was found that both the type of precursor and the conditions of activation (i.e. impregnation ratios, and activation temperatures), had a huge influence on the microporosity of the resultant samples and their CO₂ capture capacities. The carbon-based adsorbent that presented the maximum CO₂ capture capacities at 25 and 100 °C (13.8 wt.% and 3.1 wt.%, respectively), was prepared from a pre-consumer carpet waste and was activated at 700 °C using a KOH:char impregnation ratio of 1:1. This sample showed the highest narrow microporosity volume (0.47 cm³ g⁻¹), thus confirming that only pores of less than 1 nm are effective for CO₂ adsorption at atmospheric pressure.     

Water/acid gas interfacial tensions and their impact on acid gas geological storage

Acid gas geological disposal is a promising process to reduce CO₂ atmospheric emissions and an environment-friendly and economic alternative to the transformation of H₂S into sulphur by the Claus process. Acid gas confinement in geological formations is to a large extent controlled by the capillary properties of the water/acid–gas/caprock system, because a significant fraction of the injected gas rises buoyantly and accumulates beneath the caprock. These properties include the water/acid gas interfacial tension (IFT), to which the so-called capillary entry pressure of the gas in the water-saturated caprock is proportional. In this paper we present the first ever systematic water/acid gas IFT measurements carried out by the pendant drop technique under geological storage conditions. We performed IFT measurements for water/H₂S systems over a large range of pressure (up to P = 15 MPa) and temperature (up to T = 120 °C). Water/H₂S IFT decreases with increasing P and levels off at around 9–10 mN/m at high T (≥70 °C) and P (>12 MPa). The latter values are around 30–40% of water/CO₂ IFTs, and around 20% of water/CH₄ IFTs at similar T and P conditions. The IFT between water and a CO₂ + H₂S mixture at T = 77 °C and P > 7.5 MPa is observed to be approximately equal to the molar average IFT of the water/CO₂ and water/H₂S binary mixtures. Thus, when the H₂S content in the stored acid gas increases the capillary entry pressure decreases, together with the maximum height of acid gas column and potential storage capacity of a given geological formation. Hence, considerable attention should be exercised when refilling with a H₂S-rich acid gas a depleted gas reservoir, or a depleted oil reservoir with a gas cap: in the case of hydrocarbon reservoirs that were initially (i.e., at the time of their discovery) close to capillary leakage, acid gas leakage through the caprock will inevitably occur if the refilling pressure approaches the initial reservoir pressure.     

Predicting δCDIC dynamics in CCS: A scheme based on a review of inorganic carbon chemistry under elevated pressures and temperatures

Stable carbon isotopes are important tools to assess potential storage sites for CO₂, as they allow the quantification of ionic trapping via isotope mass balances. In deep geological formations high p/T conditions need to be considered, because CO₂ dissolution, equilibrium constants and isotope fractionation of dissolved inorganic carbon (DIC) depend on temperature, pressure and solute composition. After reviewing different approaches to account for these dependencies, an expanded scheme is presented for speciation and carbon isotope fractionation of DIC and dissolution of CaCO₃ for pCO₂ up to 100 bar, pH down to 3 and temperatures of up to 200 °C. The scheme evaluates the influence of respective parameters on isotope ratios during CO₂ sequestration. The pCO₂ and pH are the dominant controlling factors in the DIC/δ¹³C/pH system. The fugacity of CO₂ has major impact on DIC concentrations at temperatures below 100 °C at high pCO₂. Temperature dependency of activities and equilibrium dominates at temperatures above 100 °C. Isotope ratios of DIC are expected to be about 1–2‰ more depleted in ¹³C compared to the free CO₂ at pCO₂ values above 10 bar. This depletion is controlled by carbon isotope fractionation between CO₂ and H₂CO₃* which is the dominant species of DIC at the resulting pH below 5.     

Viscosities, thermal conductivities and diffusion coefficients of CO2 mixtures: Review of experimental data and theoretical models

Accurate experimental data on the thermo-physical properties of CO₂-mixtures are pre-requisites for development of more accurate models and hence, more precise design of CO₂ capture and storage (CCS) processes. A literature survey was conducted on both the available experimental data and the theoretical models associated with the transport properties of CO₂-mixtures within the operation windows of CCS. Gaps were identified between the available knowledge and requirements of the system design and operation. For the experimental gas-phase measurements, there are no available data about any transport properties of CO₂/H₂S, CO₂/COS and CO₂/NH₃; and except for CO₂/H₂O(/NaCl) and CO₂/amine/H₂O mixtures, there are no available measurements regarding the transport properties of any liquid-phase mixtures. In the prediction of gas-phase viscosities using Chapman–Enskog theory, deviations are typically <2% at atmospheric pressure and moderate temperatures. The deviations increase with increasing temperatures and pressures. Using both the Rigorous Kinetic Theory (RKT) and empirical models in the prediction of gas-phase thermal conductivities, typical deviations are 2.2–9%. Comparison of popular empirical models for estimation of gas-phase diffusion coefficients with newer experimental data for CO₂/H₂O shows deviations of up to 20%. For many mixtures relevant for CCS, the diffusion coefficient models based on the RKT show predictions within the experimental uncertainty. Typical reported deviations of the CO₂/H₂O system using empirical models are below 3% for the viscosity and the thermal conductivity and between 5 and 20% for the diffusion coefficients. The research community knows little about the effect of other impurities in liquid CO₂ than water, and this is an important area to focus in future work.     

Numerical parametric study on CO2 capture by indirect thermal swing adsorption

Post-combustion CO₂ capture remains one of the most-challenging issue to lower CO₂ emissions of existing power plants or heavy industry installations because of strong economy and energy efficiency aspects. The major issue comes from CO₂ dilution (4% for NGCC and 14% for PC) and the high flow rates to be treated. Furthermore, CO₂ purity has to be higher than 95% with recovery at 90%, to match the transportation/injection requirements.The MEA absorption process remains the reference today but its energy consumption (about 3 MJ/kg_CO2) and the amine consumption are still challenging drawbacks.The interest of CO₂ capture by indirect TSA (Temperature Swing Adsorption) was demonstrated experimentally in a previous work. The aim of this paper is to present the results of a numerical parametric study. Two main parameters are explored: the desorption temperature (100–200 °C) and the purge flow rate (0.1–0.5 Ndm³ min⁻¹). Four performance indicators are evaluated: CO₂ purity, recovery, productivity and specific energy consumption.Results show that purity above 95% can be achieved. Keeping the 95% target, it is possible to achieve recovery at 81% with productivity at 57.7 g_CO2/kg_ads h and a specific energy consumption of 3.23 MJ/kg_CO2, which is less than for the reference MEA process.Comparison with other adsorption processes exhibits that this process has good potential especially since some improvements are still expected from further research.     

Laboratory calibration of the seismo-acoustic response of CO2 saturated sandstones

Ultrasonic experiments were undertaken on CO₂ flooded sandstone core samples, both synthetic sandstones and core plugs from the CRC1 CO₂ injection well in the Otway Basin, Victoria, South Eastern. Australia. The aim of these laboratory tests was to investigate the effects of CO₂ as a pore fluid on the seismo-acoustic response of the sandstone and ultimately to provide an indication of the sensitivity of time-lapse seismic imaging of the eventual CO₂/CH₄ plume in the Otway, Waarre C formation.The synthetic sandstones were manufactured using both a proprietary calcium in situ precipitation (CIPS) process and a silica cementing technique. Samples were tested in a computer controlled triaxial pressure cell where pore pressures can be controlled independently of the confining pressures. The pressure cell is equipped with ultrasonic transducers housed in the loading platens. Consequently, effective pressures equivalent to those expected in the reservoir can be applied while ultrasonic testing is undertaken. Both compressional, P and shear waves, S were recorded via a digital oscilloscope at a range of effective pressure steps. Pore pressures were varied from 4 MPa to 17 MPa to represent both the gaseous and liquid phase regions of the CO₂ phase diagram. Similar experiments were conducted on core plugs from the Waarre C reservoir horizon obtained from the CRC1 injection well, but with an intervening brine-saturated step and in some cases with a CO₂/CH₄ mix of 80%/20% molar fraction which is representative of the field situation. However, the pore pressure in these experiments was held at 4 MPa. Finally, acoustic impedances and reflection coefficients were calculated for the reservoir using Gassmann theory and the implications for imaging the CO₂ plume is discussed.     

Characterization of a limestone in a batch fluidized bed reactor for sulfur retention under oxy-fuel operating conditions

CO₂ and SO₂ are some of the main polluting gases emitted into atmosphere in combustion processes using fossil fuel for energy production. The former is one of the major contributors to build-up the greenhouse effect implicated in global climate change and the latter produces acid rain. Oxy-fuel combustion is a technology, which consists in burning the fuel with a mix of pure O₂ and recirculated CO₂. With this technology the CO₂ concentration in the flue gas may be enriched up to 95%, becoming possible an easy CO₂ recovery. In addition, oxy-fuel combustion in fluidized beds allows in situ desulfurization of combustion gases by supplying calcium based sorbent.In this work, the effect of the principal operation variables affecting the sulfation reaction rate in fluidized bed reactors (temperature, CO₂ partial pressure, SO₂ concentration and particle size) under typical oxy-fuel combustion conditions have been analyzed in a batch fluidized bed reactor using a limestone as sorbent. It has been observed that sulfur retention can be carried out by direct sulfation of the CaCO₃ or by sulfation of the CaO (indirect sulfation) formed by CaCO₃ calcination. Direct sulfation and indirect sulfation operating conditions depended on the temperature and CO₂ partial pressure. The rate of direct sulfation rose with temperature and the rate of indirect sulfation for long reaction times decreased with temperature. An increase in the CO₂ partial pressure had a negative influence on the sulfation conversion reached by the limestone due to a higher temperature was needed to work in conditions of indirect sulfation. Thus, it is expected that the optimum temperature for sulfur retention in oxy-fuel combustion in fluidized bed reactors be about 925–950 °C. Sulfation reaction rate rose with decreasing sorbent particle size and increasing SO₂ concentration.     

CO2 transportation for carbon capture and storage: Sublimation of carbon dioxide from a dry ice bank

Climate change is being caused by greenhouse gases such as carbon dioxide (CO₂). Carbon capture and storage (CCS) is of interest to the scientific community as one way of achieving significant global reductions of atmospheric CO₂ emissions in the medium term. CO₂ would be captured from large stationary sources such as power plants and transported via pipelines under high pressure conditions to underground storage. If a downward leakage from a surface transportation system module occurs, the CO₂ would undergo a large temperature reduction and form a bank of “dry ice” on the ground surface; the sublimation of the gas from this bank represents an area source term for subsequent atmospheric dispersion, with an emission rate dependent on the energy balance at the bank surface. Gaseous CO₂ is denser than air and tends to remain close to the surface; it is an asphyxiant, a cerebral vasodilator and at high concentrations causes rapid circulatory insufficiency leading to coma and death. Hence a subliming bank of dry ice represents safety hazard. A model is presented for evaluating the energy balance and sublimation rate at the surface of a solid frozen CO₂ bank under different environmental conditions. The results suggest that subliming gas behaves as a proper dense gas (i.e. it remains close to the ground surface) only for low ambient wind speeds.     

Model prediction on the rise of pCO2 in uniform flows by leakage of CO2 purposefully stored under the seabed

A numerical study was conducted to predict pCO₂ change in the ocean on a continental shelf by the leakage of CO₂, which is originally stored in the aquifer under the seabed, in the case that a large fault connects the CO₂ reservoir and the seabed by an earthquake or other diastrophism. The leakage rate was set to be 6.025 × 10⁻⁴ kg/m²/sec from 2 m × 100 m fault band, which corresponds to 3800 t-CO₂/year, referring to the monitored seepage rate from an existing EOR field. The target space in this study was limited to the ocean above the seabed, the depth of which was 200 or 500 m. The computational domain was idealistically rectangular with the seabed fault-band perpendicular to the uniform flow. The CO₂ takes a form of bubbles or droplets, depending on the depth of water, and their behaviour and dissolution were numerically simulated during their rise in seawater flow. The advection–diffusion of dissolved CO₂ was also simulated. As a result, it was suggested that the leaked CO₂ droplets/bubbles all dissolve in the seawater before spouting up to the atmosphere, and that the increase in pCO₂ in the seawater was smaller than 500 μ atm.     

Comparison of several packings for CO2 chemical absorption in a packed column

CO₂ capture and storage has gained widespread attention as an option for reducing greenhouse gas emissions. Chemical absorption and stripping of CO₂ with hot potassium carbonate (K₂CO₃) solutions has been used in the past, however potassium carbonate solutions have a low CO₂ absorption efficiency. Various techniques can be used to improve the absorption efficiency of this system with one option being the addition of promoters to the solvent and another option being an improvement in the mass transfer efficiency of the equipment. This study has focused on improving the efficiency of the packed column by replacing traditional packings with newer types of packing which have been shown to have enhanced mass transfer performance. Three different packings (Super Mini Rings (SMRs), Pall Rings and Mellapak) have been studied under atmospheric conditions in a laboratory scale column for CO₂ absorption using a 30 wt% K₂CO₃ solution. It was found that SMR packing resulted in a mass transfer coefficient approximately 20% and 30% higher than that of Mellapak and Pall Rings, respectively. Therefore, the height of packed column with SMR packing would be substantially lower than with Pall Rings or Mellapak. Meanwhile, the pressure drop using SMR was comparable to other packings while the gas flooding velocity was higher when the liquid load was above 25 kg m⁻² s⁻¹. Correlations for predicting flooding gas velocities and pressure drop were fitted to the experimental data, allowing the relevant parameters to be estimated for use in later design.     

Time-lapse carbon dioxide monitoring with pulsed neutron logging

Elevated levels of CO₂ in the atmosphere have been linked to the rise in land and sea temperature [Climate Change, 2001. In: Houghton, J.T., Ding, Y., Griggs, D.J., Noguer, M., van der Linden, P.J., Xiaosu, D. (Eds.), The Scientific Basis Contribution of Working Group I to the Third Assessment Report of the Intergovernmental Panel on Climate Change (IPCC). Cambridge University Press, UK, p. 944]. To demonstrate geological carbon sequestration as a mitigation technique, a carbon dioxide injection experiment was conducted in East Texas. The target – Frio formation – is a highly porous, permeable and unconsolidated sandstone. The specific interval is the Frio C sand, which originally was saturated with saline formation water. At the injection location, the Frio C sand dips 18° to the south. To monitor the injected CO₂ spreading in the formation, an old well from 1956 drilled into the deeper Yegua formation was selected as the observation well. The injection well was drilled at a distance of 100 ft downdip from the monitoring well. Several borehole measurement methods were available to monitor the CO₂ injection, but the most suitable technology was thought to be the pulsed neutron logging. This logging is used widely in cased hole, and the measured macroscopic thermal absorption cross-section (Σ) is sensitive to CO₂ saturation in high porosity saline water environments. Several log examples are given demonstrating successful the monitoring of the CO₂ plume moving through the two boreholes and the resulting saturation changes.     

Pipeline design for a least-cost router application for CO2 transport in the CO2 sequestration cycle

CO₂ capture and geological storage (CCS) is considered as a viable option to mitigate greenhouse gas emissions during the transition phase towards the use of clean and renewable energy. This paper concentrates on the transport of CO₂ between source (CO₂ capture at plants) and sink (geological storage reservoirs). In the cost estimation of CO₂ transport, the pipeline diameter plays an important role. In this respect, the paper reviews equations that were used in several reports on CO₂ pipeline transport. As some parameters are not taken into account in these equations, alternative formulas are proposed which calculate the proper inner diameter size based on flow rate, pressure drop per unit length, CO₂ density, CO₂ viscosity, pipeline material roughness and topographic height differences (the Darcy–Weisbach solution) and, in addition, on the amount and type of bends (the Manning solution). Comparison between calculated diameters using the reviewed and the proposed equations demonstrate the important influence of elevation difference (which is not considered in the reviewed equations) and pipeline material roughness-related factor on the calculated diameter. Concerning the latter, it is suggested that a Darcy–Weisbach roughness height of 0.045 mm better corresponds to a Manning factor of 0.009 than higher Manning values previously proposed in literature. Comparison with the actual diameter of the Weyburn pipeline confirms the accuracy of the proposed equations. Comparison with other existing CO₂ pipelines (without pressure information) indicate that the pipelines are designed for lower pressure gradients than 25 Pa/m or for (future) higher flow rates. The proposed Manning equation is implemented in an economic least-cost route planner in order to obtain the best economic solution for pipeline trajectory and corresponding diameter.     

Power generation with CO2 capture: Technology for CO2 purification

The goal of this paper is to find methodologies for removing a selection of impurities (H₂O, O₂, Ar, N₂, SO_x and NO_x) from CO₂ present in the flue gas of two oxy-combustion power plants fired with either natural gas (467 MW) or pulverized fuel (596 MW). The resulting purified stream, containing mainly CO₂, is assumed to be stored in an aquifer or utilized for enhanced oil recovery (EOR) purposes. Focus has been given to power cycle efficiency i.e.: work and heat requirements for the purification process, CO₂ purity and recovery factor (kg of CO₂ that is sent to storage per kg of CO₂ in the flue gas). Two different methodologies (here called Case I and Case II) for flue gas purification have been developed, both based on phase separation using simple flash units (Case I) or a distillation column (Case II). In both cases purified flue gas is liquefied and its pressure brought to 110 atm prior to storage.Case I: A simple flue gas separation takes place by means of two flash units integrated in the CO₂ compression process. Heat in the process is removed by evaporating the purified liquid CO₂ streams coming out from both flashes. Case I shows a good performance when dealing with flue gases with low concentration of impurities. CO₂ fraction after purification is over 96% with a CO₂ recovery factor of 96.2% for the NG-fired flue gas and 88.1% for the PF-fired flue gas. Impurities removal together with flue gas compression and liquefaction reduces power plant output of 4.8% for the NG-fired flue gas and 11.6% for the PF-fired flue gas. The total amount of work requirement per kg stored CO₂ is 453 kJ for the NG-fired flue gas and 586 kJ for the PF-fired flue gas.Case II: Impurities are removed from the flue gas in a distillation column. Two refrigeration loops (ethane and propane) have been used in order to partially liquefy the flue gas and for heat removal from a partial condenser. Case II can remove higher amounts of impurities than Case I. CO₂ purity prior to storage is over 99%; CO₂ recovery factor is somewhat lower than in Case I: 95.4% for the NG-fired flue gas and 86.9% for the PF-fired flue gas, reduction in the power plant output is similar to Case I.Due to the lower CO₂ recovery factor the total amount of work per kg stored CO₂ is somewhat higher for Case II: 457 kJ for the NG-fired flue gas and 603 kJ for the PF-fired flue gas.     

Structure and thermal stability of toxic chromium(VI) species doped onto TiO2 powders through heat treatment

Chromium(VI)-containing sorbents in the form of sludge or solid residue from treatment processes are often landfilled or used as fill materials, therefore the long-term stability of metal binding is important. The reduction of Cr(VI)–Cr(III) through heat treatment may be a useful detoxification method. After heating at 500, 900, 1000, and 1100 °C for 4 h, the transformation of chemical states of chromium on 105 °C-dried, 7.9% Cr(VI)-doped TiO₂ powders was studied on the basis of surface area measurements, scanning electron microscopy (SEM) images, X-ray diffraction (XRD), and extended X-ray absorption fine structure (EXAFS) spectra. It was shown that Cr(VI) was reduced to Cr(III) in the Cr(VI)-doped samples after heating within 500–900 °C. The present results also suggested that the chromium octahedral was bridged to the titanium tetrahedral and was incorporated in TiO₂ minerals formed after 1000 °C treatment.     

A method for quick assessment of CO2 storage capacity in closed and semi-closed saline formations

Saline aquifers of high permeability bounded by overlying/underlying seals may be surrounded laterally by low-permeability zones, possibly caused by natural heterogeneity and/or faulting. Carbon dioxide (CO₂) injection into and storage in such “closed” systems with impervious seals, or “semi-closed” systems with non-ideal (low permeability) seals, is different from that in “open” systems, from which the displaced brine can easily escape laterally. In closed or semi-closed systems, the pressure buildup caused by continuous industrial-scale CO₂ injection may have a limiting effect on CO₂ storage capacity, because geomechanical damage caused by overpressure needs to be avoided. In this research, a simple analytical method was developed for the quick assessment of the CO₂ storage capacity in such closed and semi-closed systems. This quick-assessment method is based on the fact that native brine (of an equivalent volume) displaced by the cumulative injected CO₂ occupies additional pore volume within the storage formation and the seals, provided by pore and brine compressibility in response to pressure buildup. With non-ideal seals, brine may also leak through the seals into overlying/underlying formations. The quick-assessment method calculates these brine displacement contributions in response to an estimated average pressure buildup in the storage reservoir. The CO₂ storage capacity and the transient domain-averaged pressure buildup estimated through the quick-assessment method were compared with the “true” values obtained using detailed numerical simulations of CO₂ and brine transport in a two-dimensional radial system. The good agreement indicates that the proposed method can produce reasonable approximations for storage–formation–seal systems of various geometric and hydrogeological properties.     

Numerical investigation concerning the impact of CO2 geologic storage on regional groundwater flow

Large-scale storage of carbon dioxide in saline aquifers may cause considerable pressure perturbation and brine migration in deep rock formations, which may have a significant influence on the regional groundwater system. With the help of parallel computing techniques, we conducted a comprehensive, large-scale numerical simulation of CO₂ geologic storage that predicts not only CO₂ migration, but also its impact on regional groundwater flow. As a case study, a hypothetical industrial-scale CO₂ injection in Tokyo Bay, which is surrounded by the most heavily industrialized area in Japan, was considered, and the impact of CO₂ injection on near-surface aquifers was investigated, assuming relatively high seal-layer permeability (higher than 10 microdarcy). A regional hydrogeological model with an area of about 60 km × 70 km around Tokyo Bay was discretized into about 10 million gridblocks. To solve the high-resolution model efficiently, we used a parallelized multiphase flow simulator TOUGH2-MP/ECO2N on a world-class high performance supercomputer in Japan, the Earth Simulator. In this simulation, CO₂ was injected into a storage aquifer at about 1 km depth under Tokyo Bay from 10 wells, at a total rate of 10 million tons/year for 100 years. Through the model, we can examine regional groundwater pressure buildup and groundwater migration to the land surface. The results suggest that even if containment of CO₂ plume is ensured, pressure buildup on the order of a few bars can occur in the shallow confined aquifers over extensive regions, including urban inlands.     

Study on the failure mechanism of potassium-based sorbent for CO2 capture and the improving measure

With thermogravimetric apparatus (TGA), X-ray diffraction (XRD) and barium sulfate gravimetric methods, the carbonation reactivities of K₂CO₃ and K₂CO₃/Al₂O₃ in the simulated flue gases with SO₂ are investigated and the reaction equations are inferred. Results show that there are KHCO₃ and K₂SO₃ generated. The generation K₂SO₃ reduces the utilization ratio of the sorbent. H₂O may accelerates the sulfation reaction of AR K₂CO₃ as K₄H₂(CO₃)₃·1.5H₂O is generated in the reaction among K₂CO₃, SO₂ and H₂O. K₂SO₃ is directly generated from sulfation reaction of K₂CO₃/Al₂O₃, because there are K₂CO₃·1.5H₂O and K₂SO₃ generated in the reaction among K₂CO₃/Al₂O₃, SO₂ and H₂O. K₂CO₃·1.5H₂O does not react with SO₂, and K₂CO₃·1.5H₂O/Al₂O₃ reacts with SO₂ slowly. Compare with the reaction process without H₂O pretreatment, the reaction rates of KAl30 increased after H₂O pretreatment and the failure ratio is about a half of that without H₂O pretreatment. So, K₂CO₃/Al₂O₃ shows good carbonation and anti-sulfation characteristic after H₂O pretreatment.     

Petrophysical analysis to investigate the effects of carbon dioxide storage in a subsurface saline aquifer at Ketzin, Germany (CO2SINK)

To test the injection behaviour of CO₂ into brine-saturated rock and to evaluate the dependence of geophysical properties on CO₂ injection, flow and exposure experiments with brine and CO₂ were performed on sandstone samples of the Stuttgart Formation representing potential reservoir rocks for CO₂ storage. The sandstone samples studied are generally fine-grained with porosities between 17 and 32% and permeabilities between 1 and 100 mD.Additional batch experiments were performed to predict the long-term behaviour of geological CO₂ storage. Reservoir rock samples were exposed over a period of several months to CO₂-saturated reservoir fluid in high-pressure vessels under in situ temperature and pressure conditions. Petrophysical parameters, porosity and the pore radius distribution were investigated before and after the experiments by NMR (Nuclear Magnetic Resonance) relaxation and mercury injection. Most of the NMR measurements of the tested samples showed a slight increase of porosity and a higher proportion of large pores.     

Methodology for CO2 chain analysis

The paper presents a methodology for CO₂ chain analysis with particular focus on the impact of technology development on the total system economy. The methodology includes the whole CO₂ chain; CO₂ source, CO₂ capture, transport and storage in aquifers or in oil reservoirs for enhanced oil recovery. It aims at supporting the identification of feasible solutions and assisting the selection of the most cost-effective options for carbon capture and storage. To demonstrate the applicability of the methodology a case study has been carried out to illustrate the possible impact of technology improvements and market development. The case study confirms that the CO₂-quota price to a large extent influence the project economy and dominates over potential technology improvements. To be economic feasible, the studied chains injecting the CO₂ in oil reservoirs for increased oil production require a CO₂-quota price in the range of 20–27 €/tonne CO₂, depending on the technology breakthrough. For the chains based on CO₂ storage in saline aquifers, the corresponding CO₂-quota price varies up to about 40 €/tonne CO₂.