Remediation of soil contaminated with pyrene using ground nanoscale zero-valent iron

The sites contaminated with recalcitrant polycyclic aromatic hydrocarbons (PAHs) are serious environmental problems ubiquitously. Some PAHs have proven to be carcinogenic and hazardous. Therefore, the innovative PAH in situ remediation technologies have to be developed instantaneously. Recently, the nanoscale zero-valent iron (ZVI) particles have been successfully applied for dechlorination of organic pollutants in water, yet little research has investigated for the soil remediation so far. The objective in this work was to take advantage of nanoscale ZVI particles to remove PAHs in soil. The experimental factors such as reaction time, particle diameter and iron dosage and surface area were considered and optimized. From the results, both microscale and nanoscale ZVI were capable to remove the target compound. The higher removal efficiencies of nanoscale ZVI particles were obtained because the specific surface areas were about several dozens larger than that of commercially microscale ZVI particles. The optimal parameters were observed as 0.2 g iron/2 mL water in 60 min and 150 rpm by nanoscale ZVI. Additionally, the results proved that nanoscale ZVI particles are a promising technology for soil remediation and are encouraged in the near future environmental applications. Additionally, the empirical equation developed for pyrene removal efficiency provided the good explanation of reaction behavior. Ultimately, the calculated values by this equation were in a good agreement with the experimental data.     

Removal of TNT and RDX from water and soil using iron metal

Contaminated water and soil at active or abandoned munitions plants is a serious problem since these compounds pose risks to human health and can be toxic to aquatic and terrestrial life. Our objective was to determine if zero-valent iron (Fe(0)) could be used to promote remediation of water and soil contaminated with 2,4,6-trinitrotoluene (TNT) and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX). As little as 1% Fe(0) (w/v) removed 70 mg TNT litre(-1) from aqueous solution within 8 h and removed 32 mg RDX litre(-1) within 96 h. Treating slurries (1:5 soil:water) of highly contaminated soil (5200 mg TNT and 6400 mg RDX kg(-1) soil) from the former Nebraska Ordnance Plant (NOP) with 10% Fe(0) (w/w soil) reduced CH(3)CN-extractable TNT and RDX concentrations below USEPA remediation goals (17.2 mg TNT and 5.8 mg RDX kg(-1)). Sequential treatment of a TNT-contaminated solution (70 mg TNT litre(-1) spiked with (14)C-TNT) with Fe(0) (5% w/v) followed by H(2)O(2) (1% v/v) completely destroyed TNT and removed about 94% of the (14)C from solution, 48% of which was mineralized to (14)CO(2) within 8 h. Fe(0)-treated TNT also was more susceptible to biological mineralization. Our observations indicate that Fe(0) alone, Fe(0) followed by H(2)O(2), or Fe(0) in combination with biotic treatment can be used for effective remediation of munitions-contaminated water and soil.     

Remediation of soil contaminated with dioxins by subcritical water extraction

The effectiveness of subcritical water extraction (SCWE) was examined for removing dioxins from contaminated soil. Most dioxins in the soil sample were reduced at 300 degrees C or more, but decreased dioxin concentrations were also observed at 150 degrees C. After 4 h of extraction, 99.4%, 94.5% and 60% of PCDDs were removed from samples at 350, 300 and 150 degrees C, respectively. It was also determined that degradation of dioxins had occurred, since the sum of dioxins in the soil plus water extracts after the experiments had considerably decreased. This study revealed that pressurizing is not essential for the removal of dioxins. Reduction was complete within 30 min at 350 degrees C; however, it took a much longer time at lower temperatures. The results of addition experiments in which OCDDs were added to different types of soil samples have shown that dechlorination is one of the major reaction pathways. After addition of OCDD to soil samples, experiments were carried out to examine in detail the degradation pathways of PCDDs. The removal rates and congener profiles varied among soil types. Although it was previously assumed that removal rates and congener profiles depended on the chemical components in soil, nonparametric statistical analysis revealed no significant relationship between the rate of reduction and elements present in the soil. It was confirmed from isomer patterns that dechlorination of the 2,3,7,8-positions in PCDDs takes place somewhat faster than for the 1,4,6,9-positions.     

Remediation of s-triazines contaminated water in a laboratory scale apparatus using zero-valent iron powder

Atrazine, propazine and simazine were tested separately and in mixture by batch procedure in a laboratory-constructed apparatus. 3.75 l of a buffered s-triazines pesticide solution was treated at room temperature by 325-mesh zero-valent iron powder (ZVIP) (20 g/l). High performance liquid chromatography was used to separate by-products and study the decline in the pesticide’s concentrations. Results obtained show that the order of degradation was simazine, atrazine and then propazine. The half-lives (t_1/2) of the s-triazines pesticides are, respectively, 7.4, 9.0 and 10.6 min when they are treated separately, and 9.8, 11.2 and 13.7 min when they are treated together under the same conditions. The final by-product obtained after 50 min of contact of simazine with ZVIP shows a shift to longer wavelength in its UV spectrum. A similar phenomenon is shown for atrazine and propazine. Identical primary by-products are produced and subsequently degraded to 4,6-(diamino)-s-triazine, which seems to be the major by-product of the reductive treatment process. Pathways for the degradation of the studied s-triazines by ZVIP are proposed.     

Remediation of PCB contaminated soils using iron nano-particles

In this study, iron nano-particles were used to remediate PCB contaminated soil and an attempt was made to maximize PCB destruction in each treatment step. The results show that nano-particles do aid in the dechlorination process and high PCB destruction efficiencies can be achieved. The destruction efficiency during the preliminary treatment (mixing of soil and iron nano-particles in water) can be increased by increasing the water temperature. The maximum thermal destruction (pyrolysis/combustion of soil after preliminary treatment) of soil-bound PCBs occurs at 300 degrees C in air. A minimum total PCB destruction efficiency of 95% can be achieved by this process. The effect of changing treatment parameters such as type of mixing, time of mixing and mixing conditions and application of other catalysts like iron oxide and V(2)O(5)/TiO(2) was also investigated. It was found that at 300 degrees C in air, iron oxide and V(2)O(5)/TiO(2) are also good catalysts for remediating PCB contaminated soils.     

Amendment of arsenic and chromium polluted soil from wood preservation by iron residues from water treatment

An iron-rich water treatment residue (WTR) consisting mainly of ferrihydrite was used for immobilization of arsenic and chromium in a soil contaminated by wood preservatives. A leaching batch experiment was conducted using two soils, a highly contaminated soil (1033 mg kg⁻¹ As and 371 mg kg⁻¹ Cr) and slightly contaminated soil (225 mg kg⁻¹ As and 27 mg kg⁻¹ Cr). Compared to an untreated reference soil, amendment with 5% WTR reduced leaching in the highly contaminated soil by 91% for Cr and 98% for As. No aging effect was observed after 103 d. In a small field experiment, soil was mixed with 2.5% WTR in situ. Pore water was extracted during 3 years from the amended soil and a control site. Pore water arsenic concentrations in the amended soil were more than two orders of magnitude lower than in the control for the upper samplers. An increased release of arsenic was observed during winter in both fields, mostly in the deepest samplers. This is likely due to the formation of a pseudo-gley because of precipitation surplus. Stabilization of arsenic and chromium contaminated soil using WTR is a promising method but the transformation of ferrihydrite in soil proves a concern in case of waterlogged soils. Still the amendment minimized the leaching of arsenic, even in cases of seasonal releases.     

Remediation of alachlor and atrazine contaminated water with zero-valent iron nanoparticles

Zero-valent iron nanoparticles (nZVI, diameter < 90 nm, specific surface area = 25 m² g^?1) have been used under anoxic conditions for the remediation of pesticides alachlor and atrazine in water. While alachlor (10, 20, 40 mg L^?1) was reduced by 92–96% within 72 h, no degradation of atrazine was observed. The alachlor degradation reaction was found to obey first-order kinetics very closely. The reaction rate (35.5 × 10^?3–43.0 × 10^?3 h^?1) increased with increasing alachlor concentration. The results are in conformity with other researchers who worked on these pesticides but mostly with micro ZVI and iron filings. This is for the first time that alachlor has been degraded under reductive environment using nZVI. The authors contend that nZVI may prove to be a simple method for on-site treatment of high concentration pesticide rinse water (100 mg L^?1) and for use in flooring materials in pesticide filling and storage stations.     

Selection of surfactant in remediation of DDT-contaminated soil by comparison of surfactant effectiveness

With an aim to select the most appropriate surfactant for remediation of DDT-contaminated soil, the performance of nonionic surfactants Tween80, TX-100, and Brij35 and one anionic surfactant sodium dodecyl benzene sulfonate (SDBS) in enhancement of DDT water solubility and desorption of DDT from contaminated soil and their adsorption onto soil and ecotoxicities were investigated in this study. Tween80 had the highest solubilizing and soil-washing ability for DDT among the four experimental surfactants. The adsorption loss of surfactants onto soil followed the order of TX-100 > Tween80 > Brij35 > SDBS. The ecotoxicity of Tween80 to ryegrass (Lolium perenne L.) was lowest. The overall performance considering about the above four aspects suggested that Tween80 should be selected for the remediation of DDT-contaminated soil, because Tween80 had the greatest solubilizing and soil-washing ability for DDT, less adsorption loss onto soil, and the lowest ecotoxicity in this experiment.     

Remediation of s-triazines contaminated water in a laboratory scale apparatus using zero-valent iron powder

Atrazine, propazine and simazine were tested separately and in mixture by batch procedure in a laboratory-constructed apparatus. 3.75 l of a buffered s-triazines pesticide solution was treated at room temperature by 325-mesh zero-valent iron powder (ZVIP) (20 g/l). High performance liquid chromatography was used to separate by-products and study the decline in the pesticide’s concentrations. Results obtained show that the order of degradation was simazine, atrazine and then propazine. The half-lives (t_1/2) of the s-triazines pesticides are, respectively, 7.4, 9.0 and 10.6 min when they are treated separately, and 9.8, 11.2 and 13.7 min when they are treated together under the same conditions. The final by-product obtained after 50 min of contact of simazine with ZVIP shows a shift to longer wavelength in its UV spectrum. A similar phenomenon is shown for atrazine and propazine. Identical primary by-products are produced and subsequently degraded to 4,6-(diamino)-s-triazine, which seems to be the major by-product of the reductive treatment process. Pathways for the degradation of the studied s-triazines by ZVIP are proposed.     

Remediation of a biodiesel blend-contaminated soil by using a modified Fenton process

A soil contaminated with a B20 biodiesel blend (20 % biodiesel, 80 % diesel) has been treated by modified Fenton process with or without chelant addition. All experiments were conducted without pH adjustment. The reagents used were as follows: hydrogen peroxide as oxidant (400–4,000 mmol L^?1), ferric ion as catalyst (5–20 mmol L^?1), and trisodium citrate (50 mmol L^?1) as chelating agent. Soil was spiked at two different pollutant concentrations (1,000–10,000 mg diesel kg^?1 soil). Higher total petroleum hydrocarbon (TPH) removal efficiencies were obtained (up to 75 %) after the treatment in the absence of the chelant due to the low pH obtained in this case. In the presence of chelant, the TPH conversion obtained was lower because both higher pH is obtained and chelant competes with diesel for the oxidant. On the other hand, at neutral pH, the lifetime of the oxidant was increased. Fatty acid methyl esters (FAMEs) are easier to remove than diesel aliphatic hydrocarbons from the blend. An important decrease of the aqueous phase toxicity was observed after the modified Fenton reaction, supporting that nontoxic by-products were released to the aqueous phase during the treatment.     

热水洗辅助微生物修复高含油落地油泥

为解决油田落地油泥含油率高但不能直接进行生物无害化处置的问题,探索一种热水洗辅助微生物修复工艺。利用热水洗实验考察了清洗配方和水温对降低含油率的影响;从落地油泥中分离出石油烃降解菌,以用于含油残砂的微生物降解过程,同时探究填料和烃降解微生物对残砂中石油烃降解效果的影响。结果表明,鼠李糖脂清洗剂在总用量为0.5%、水洗时间30 min和50 ℃条件下,可将油泥含油率由107.1 mg·g⁻¹降至为39.3 mg·g⁻¹;水洗后残砂中的土著菌群数量出现了明显下降。分离获得了2株烃降解菌,并优选出具有增加油泥溶氧和保水的沼渣。将烃降解微生物和优选沼渣加入残砂后,石油烃生物降解效率得到显著提升,200 d后含油率降为4.62 mg·g⁻¹。在此过程中,微生物优先降解分子量小的饱和烃和芳香烃组分,对胶质和沥青质等组分降解程度偏低。该研究结果可为油田高含油落地油泥的环保处置提供参考。     

不同化学淋洗剂对复合重金属污染土壤的修复机理

化学淋洗技术是一种常用的重金属污染土壤修复技术,化学淋洗剂的选择尤为重要。以乙二胺四乙酸二钠（EDTA）、柠檬酸（CA）和三氯化铁（FeCl3）为化学淋洗剂,采用振荡淋洗法研究淋洗时间与淋洗剂浓度对Cu、Zn、Pb和Cd去除效果的影响,分析重金属污染土壤淋洗前后重金属形态与基本理化性质的变化。结果表明：3种化学淋洗剂对重金属的快速反应阶段基本在60 min内,在240 min达到淋洗平衡,对Pb和Cd的淋洗主要是非均相扩散过程;EDTA、柠檬酸和FeCl3对重金属的去除能力依次为Pb>Cd>Cu>Zn,Cd>Zn>Cu>Pb与Pb≈Cd>Cu>Zn,EDTA的淋洗效率最高,Cd的解吸能力最强;EDTA和FeCl3可有效去除弱酸可溶态与可还原态重金属,柠檬酸能有效去除弱酸可溶态重金属,修复后的土壤仍有环境风险;3种淋洗剂修复后的土壤中总有机碳与粒径分布无明显变化,FeCl3会酸化土壤。综合考虑,EDTA、柠檬酸和FeCl3均为淋洗效果好的环境友好型化学淋洗剂,该研究成果可用于现场淋洗去除土壤中重金属的小试。     

Amelioration of alkali soil using flue gas desulfurization byproducts: productivity and environmental quality

In this study, flue gas desulfurization (FGD) byproducts are used to ameliorate alkali soil. The average application rates for soils with low exchangeable sodium percentage (ESP), mid ESP, and high ESP are 20.9, 30.6, and 59.3 Mg ha(-1), respectively. The experimental results obtained for 3 consecutive years reveal that the emergence ratios and yields of the crops were 1.1-7.6 times and 1.1-13.9 times those of the untreated control, respectively. The concentrations of Cr, Pb, Cd, As, and Hg in the treated soils are far below the background values stipulated by the Environmental Quality Standard for Soils (GB15618-1995). Their concentrations in the seeds of corn and alfalfa grown in the treated soils are far below the tolerance limits regulated by National Food Standards of China. The results of this research demonstrate that the amelioration of alkali soils using FGD byproducts is promising.     

Remediation of DDTs contaminated soil in a novel Fenton-like system with zero-valent iron

Application of a novel Fenton-like system with zero-valent iron, EDTA and Air (ZVI/EDTA/Air) was investigated to degrade dichlorodiphenyltrichloroethane (DDT), dichlorodiphenyldichloroethane, and dichlorodiphenyldichloroethylene (DDE) in the actual contaminated soil from an organochlorine pesticide site. It was found DDTs in the soil were effectively degraded by the system at room temperature, ambient atmosphere pressure and near neutral pH. The dosages of EDTA and ZVI were the dominant factors influencing the removal of contaminants. An increase of EDTA from 0.05 to 0.2 mM and ZVI from 1 to 5 g L^?1 improved the removal of the contaminants significantly. However, excessive amount of EDTA led to a negative effect on the degradation process. Meanwhile, EDTA was simultaneously degraded so as to avoid the secondary pollution risk on soil remediation. Only a small amount of 4,4′-DDE and 2,2-bis(4-chlorophenyl)-1-chloroethylene (4,4′-DDMU) generated as the intermediates of DDT degradation during the process. Our investigation suggests that the Fenton-like system is a promising alternative for remediation of organochlorine pesticides contaminated soils.     

Dynamic and equilibrium studies of the RDX removal from soil using CMC-coated zerovalent iron nanoparticles

Rapid chemical degradation of toxic RDX explosive in soil can be accomplished using zerovalent nanoiron suspension stabilized in dilute carboxymethyl cellulose solution (CMC-ZVINs). The effect of operating conditions (redox-potential, Fe/RDX molar ratio) was studied on batchwise removal of RDX in contaminated soil. While anaerobic conditions resulted in 98% RDX removal in 3 h, only slightly over 60% RDX removal could be attained under aerobic conditions. The molar ratio did not have any influence on the intermediate and final RDX degradation products (methylenedinitramine, nitroso derivative, N₂, N₂O, NO₂^?), however, their distribution changed. Dynamic studies were conducted using a flow-through short column packed with RDX-contaminated soil and fed with CMC-ZVINs. The column was operated at two interstitial velocities (2.2 and 1.6 cm min^?1), resulting in the 76.6% and 95% removal of the initial RDX soil contamination load (60 mg kg^?1), respectively. While the column operating conditions could be further optimized, 95% of the RDX initially present in the contaminated soil packed in the column was degraded when flushed with a CMC-ZVINs suspension in this work.     

污泥生物炭对土壤中Pb和Cd的生物有效性的影响

以污泥为原料,在500 ℃缺氧条件下制备污泥生物炭,结合X射线能谱（EDS）、环境扫描电镜（SEM）和红外光谱（FTIR）等表征手段,分析添加污泥生物炭后污染土壤pH和Pb与Cd化学形态的变化来探究污泥生物炭对土壤中Pb、Cd的固定效果,并用盆栽方式评估添加污泥生物炭对小青菜生物量及体内重金属含量的影响。结果表明：添加污泥生物炭后,污染土壤的pH随平衡时间的延长显著升高;对于单一污染土壤和复合污染土壤,污泥生物炭对Pb和Cd均有较强的固定作用,而污泥生物炭在复合污染土壤中对Pb的固定效果优于在单一污染土壤中;添加污泥生物炭能提高小青菜的生物量,且能有效降低小青菜对污染土壤中Pb和Cd的吸收。     

厌氧动态膜生物反应器处理冷轧平整液废水

平整液废水作为碱性含油废水,一直是冶金行业较难处理的废水之一。搭建了一套厌氧动态膜生物反应器（AnDMBR）,通过梯级驯化的方式,处理COD为2 500 mg·L-1左右的平整液废水。经过88 d的启动驯化,在膜通量为6 L·（m2·h）-1,HRT为2.5 d的条件下,出水稳定在500 mg·L-1左右,甲烷产率约0.151 L·g-1,动态膜的一个运行周期可以分为成膜阶段、稳定阶段和堵塞阶段3个阶段。成膜阶段出水浊度随动态膜的逐渐形成而下降;而后动态膜形成,出水浊度稳定,为稳定阶段;最后为堵塞阶段,跨膜压差激增,出水浊度上升。同时对驯化及稳定运行阶段的污泥进行了微生物菌群分析,在细菌群落中主要的微生物菌群为Clostridia（梭状芽胞杆菌纲）、Bacteroidia（拟杆菌纲）、Anaerolineae（厌氧绳菌纲）、OP8_1和Spirochaetes（螺旋体纲）,其中拟杆菌纲是处理平整液废水的优势细菌菌群。在古菌群落中,Methanolinea（甲烷绳菌属）和Methanosaeta（甲烷鬃毛菌属）为主要菌种,随着反应器的长期驯化和运行,甲烷鬃毛菌逐渐成为反应器中优势菌群。     

Remediation of MTBE from drinking water: air stripping followed by off-gas adsorption

The widespread use of methyl tertiary butyl ether (MTBE) as an oxygenate in gasoline has resulted in the contamination of a large number of ground and surface water sources. Even though air stripping has been proven to be an effective treatment technology for MTBE removal, off-gas treatment often is required in conjunction with it. This study evaluated the combined treatment technologies of air stripping followed by off-gas adsorption on a pilot scale for the treatment of MTBE-contaminated water. The effect of air/water ratios on the treatment efficiency was studied, and the mass transfer coefficient was determined. Air/water ratios of 105:1, 151:1, 177:1, 190:1, 202:1, and 206:1 were used, and a treatment efficiency of >99% was achieved for all the runs conducted. The depth of packing required to achieve maximum treatment efficiency decreased with increasing air/water ratio. Relative humidity (RH) impacts on the MTBE adsorption capacity of a granular activated carbon (GAC) and carbonaceous resin were determined from pilot plant studies. Breakthrough profiles obtained from the pilot plant studies conducted at 20, 30, and 50% RH indicated that GAC has a higher adsorptive capacity than resin. The adsorptive capacity of GAC decreased with increasing RH, whereas RH did not impact the resin adsorptive capacity.     

白腐真菌降解经微电解预处理二硝基重氮酚废水的研究

利用自行培养、驯化的白腐真菌,对经过微电解预处理的二硝基重氮酚(DDNP)废水进行了生物降解试验.结果表明,经过微电解预处理后的DDNP废水(含CODCr467 mg/L)经生化处理108 h后,出水中CODCr在131 mg/L左右,达到国家二级排放标准;其中的苯胺类、硝基类的去除率达到99.9%以上,达到国家一级排放标准.对试验所获得的时间序列进行动力学研究结果证明,白腐真菌降解经微电解预处理后的DDNP废水的反应为准一级动力学反应.     

高岭土模拟铜污染土壤电动力学修复

采用电动力学方法修复重金属污染土壤。研究中采用高岭土模拟铜污染土壤,结合电动力学修复理论,考察了不同电压、添加络合剂条件下铜的修复效果。结果表明,当电压强度为0．5V／cm时,最靠近阴极部分的土壤中Cu^2＋的C／C。为1．596,当电压强度为1V／cm时,C／C0为2．245,说明适当提高电压强度能够有效的增加Cu^2＋的迁移效果;土壤中未加入络合剂时,Cu^2＋大部分集中在第5段土壤中,C／C0为1．339,在土壤中加入络合剂以后Cu^2＋大部分集中在靠近阴极部分的土壤中,C／C。为1．716,说明在污染土壤中加入一定量的络合剂可以与Cu^2＋结合生成螯合物,提高Cu^2＋的迁移效果。