The enhanced PC and PEC oxidation of formic acid in aqueous solution using a Cu-TiO2/ITO film

The photocatalytic (PC) and photoelectrocatalytic (PEC) activity of Cu-TiO2/ITO films for degrading formic acid in aqueous solution was investigated in this study. Compared with a TiO2/ITO film, the degradation efficiency of formic acid on the Cu-TiO2 films increased markedly in both the PC and PEC oxidation processes. However, it was found that the photodeposited Cu metal on the Cu-TiO2 films could electrochemically dissolute during the PEC reaction, while an electrical bias with the voltage higher than 1.48 V was applied. It is believed this is a common problem occurred for several metals deposition on the TiO2 films, which results in a poor stability of the metal-deposited TiO2 electrode in PEC processes. To improve the stability of the Cu-TiO2 electrode, an alternative process between PC and PEC reactions was investigated. It was found that the dissolute Cu metal during the PEC process was re-deposited on the Cu-TiO2 film again during the PC process. The experiments with repeated runs demonstrated that this alternative process could not only overcome the loss of Cu, but also enhance the PEC oxidation efficiency of the Cu-TiO2 films.     

铂铈共掺杂纳米TiO2的制备、表征及光催化性能

以钛酸四丁酯为前驱体,过氧化氢为氧化剂,采用简单易行的低温氧化法制备出晶粒尺寸较小（平均尺寸25nm）的二氧化钛纳米粒子。通过贵金属Pt掺杂TiO2（Pt-TiO2）、稀土元素Ce掺杂TiO2（Ce-TiO2）和Pt、Ce共掺杂TiO2（Pt／Ce-TiO2）的掺杂的方法对二氧化钛进行改性。通过XRD,XPS,TEM,紫外漫反射等表征手段对制备的样品进行表征。通过可见光下降解罗丹明B来测试其光催化活性。实验结果表明,由ce掺杂的TiO2光催化剂对有机污染物的最大降解能力略大于Pt掺杂的TiO2,2种元素进行共同掺杂时对应的TiO2光催化剂降解能力最大。     

Photocatalytic activity of TiO2 films grown on different substrates

Titanium dioxide films were prepared on glass, indium-tin oxide (ITO) glass and p-type monocrystalline silicon and studied for the photocatalytic degradation of rhodamine B in an aqueous medium. Raman, AFM, and XPS spectroscopic investigations of these films indicated that microstructure of titanium oxide films were greatly affected by the substrate materials. Rutile was confirmed to be easily formed on the surface of ITO glass, and TiO2 tended to grow as closely packed particles that were elongated strips with an average size of 20 nm, and had lovely contrast with the perfectly round particles grown on p-type monocrystalline silicon. Charge transfer between the film and silicon substrate was verified by surface photovoltage spectra. This may be the real reason why the films grown on ITO glass and silicon substrates exhibit higher photocatalytic reactivity than the film on glass substrate. Moreover, the different surface properties also seem to be responsible for the different activity.     

Photocatalytic production of hydrogen in single component and mixture systems of electron donors and monitoring adsorption of donors by in situ infrared spectroscopy

The photocatalytic production of hydrogen using aqueous Pt/TiO2 suspension has been investigated in single component and mixture systems of electron donors (pollutants). The reaction systems consisted of oxalic acid, formic acid and formaldehyde, respectively. The adsorption of these donors on TiO2 was also monitored by in situ attenuated total reflection infrared spectroscopy (ATRIR). In the single component systems, the efficiency order of electron donors is as follows: H2C2O4 > HCOOH > HCHO. The order is consistent with the order of adsorption affinity of the electron donors on TiO2 determined by ATRIR, which suggests a link between the strength of surface interaction and the efficiency of photocatalytic hydrogen evolution. In the binary mixture systems, competitive inhibition kinetics is observed. When a donor adsorbed strongly on TiO2 in a state of saturated adsorption in a binary system, the overall rate of the hydrogen evolution is consistent with that of decomposition of the donor, and the system can be treated as a single component system.     

Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

固定化催化剂TiO2膜光催化降解三氯乙醛的研究

研究了负载于玻璃上的固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果,探讨了TiO2膜光催化降解三氯乙醛的机理,考察了溶液pH值和三氯乙醛初始浓度埘TiO2膜光催化降解三氯乙醛的影响,并研究了固定化催化剂TiO2膜光催化降解三氯乙醛的动力学.结果表明,固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果良好,当三氯乙醛初始浓度为2.25 mg/L时,在紫外光照时间3 h下,三氯乙醛的降解率高达100%.在相司紫外光照时间下,三氯乙醛的光催化降解率随着三氯乙醛初始浓度的增大而下降.在溶液pH=6.5时,三氯乙醛的降解效率最高.固定化催化剂TiO2膜光催化降解三氯乙醛的反应遵循一级反应动力学,反应速率常数随三氯乙醛初始浓度的增大而减小.     

Comparison of advanced oxidation processes and identification of monuron photodegradation products in aqueous solution

The photodegradation of monuron (3-(4-chlorophenyl)-1,1-dimethylurea) in aqueous solutions under simulated solar irradiation has been conducted by different advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/H(2)O(2)/TiO(2), UV/TiO(2), dark H(2)O(2)/Fe(3+)). The degradation rates were always higher for the homogeneous catalysis in photo-Fenton reactions (UV/H(2)O(2)/Fe(2+)) compared to the heterogeneous photocatalytic systems (TiO(2)/UV and UV/H(2)O(2)/TiO(2)). Optimal concentrations of Fe(2+) and H(2)O(2) for the abatement of the herbicide in the photo-Fenton system were found to be 1 mM Fe(II) and 10 mM H(2)O(2). Several intermediary products were identified using large volume injection micro-liquid chromatography with UV detection (mu-LC-UV), mu-LC-MS and GC-MS techniques and a degradation mechanism has been proposed.     

SO2-4/TiO2光催化降解苯酚

以工业硫酸氧钛为原料水解制得SO42-/TiO2光催化剂,并以苯酚为目标降解物,考察了SO24-/TiO2的光催化性能。结果表明:随着SO42-/TiO2制备过程中焙烧温度的升高,其光催化活性逐渐增加,650℃焙烧获得的SO24-/TiO2的光催化活性最好,此后再升高温度会因催化剂中硫的挥发而下降;在确定苯酚原液初始浓度为50 mg/L条件下,SO42-/TiO2的光催化降解苯酚的最佳工艺条件为反应时间2 h、苯酚pH为7、催化剂用量1 g/L。XRD、SEM和FTIR的分析结果显示实验温度下制得的SO42-/TiO2均为锐钛型TiO2;其间掺杂的SO24-在TiO2表面分散性较好,没有聚集成大的颗粒;红外分析的结果初步判定低温(<550℃)焙烧制得的催化剂SO42-在TiO2表面是螯合双配位吸附,高温焙烧时(>550℃)SO42-在TiO2表面是桥式配位吸附。     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.     

纳米TiO2光催化氧化去除水中痕量双氯芬酸的研究

以TiCl4为前驱体,采用水解法经不同温度煅烧制备了具有不同理化性能的纳米TiO2光催化剂。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、物理吸附仪、紫外—可见光漫反射吸收光谱(UV-Vis DRS)等手段对纳米TiO2的晶相结构、粒径、孔径分布以及禁带宽度等进行了表征。以蒸馏水配制的双氯芬酸溶液为目标物,进行了纳米TiO2光催化氧化去除双氯芬酸的活性测试,研究了纳米TiO2的理化性能与光催化氧化活性之间的关系。结果表明,经400℃煅烧制得的纳米TiO2样品具有最高的光催化氧化活性,其在紫外光照射60min下对双氯芬酸的去除率为98%左右,比单独紫外光照射高出85百分点。纳米TiO2光催化氧化去除双氯芬酸的反应近似一级反应动力学模型,其中经400℃煅烧制得的纳米TiO2光催化氧化去除双氯芬酸的表观反应速率常数为0.054 54min-1,是普通商用TiO2的2倍左右,与德国Degussa P-25TiO2的光催化氧化活性最相近。     

Titania-supported silver-based bimetallic nanoparticles as photocatalysts

Photocatalytic process has shown recently a great potential as an environmental friendly and clean remediation technology for organic pollutants in wastewater. This work described the synthesis of silver-based bimetallic nanoparticles using colloid chemistry and the subsequent immobilization onto titania to form composite photocatalytic materials (titania-supported Ag–Pt nanoparticles). The photocatalysts were characterized by X-ray diffraction, electron microscopy, and nitrogen physisorption. The catalytic activity of the photocatalysts was evaluated by photocatalytic degradation of phenol and 2-chlorophenol (2-CP) in synthetic wastewater solutions. The photocatalytic processes were conducted in a batch photoreactor containing appropriate solutions of phenol and 2-CP with UV irradiation of 450 W. UV-visible spectrophotometer was used for analyzing the concentration of phenol and 2-CP in solutions. Parameters affecting the photocatalytic process such as the solution pH, phenol and 2-CP concentrations, and catalyst concentration were investigated. The results obtained revealed that TiO₂-supported Ag/Pt nanoparticles showed a higher activity for UV-photocatalytic degradation of both phenol and 2-CP pollutants in the solution (as compared to the plain rutile TiO₂). The photodegradation processes were optimized by the 0.5-g/L catalyst with a pollutant concentration of 50 mg/L for all the samples. Complete degradation for both phenol and 2-CP was achieved after 120 min.     

活性炭纤维负载TiO_2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响.结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%.     

石英棒负载TiO2光催化膜的制备、表征与降解性能

利用浸涂法在石英光导棒上制得了TiO2光催化膜.用扫描电镜(SEM)、X射线衍射(XRD)等方法对膜的形貌和晶相组成进行了表征,以苯酚为模型污染物考察了膜的活性.结果表明,所制得的TiO2膜催化剂主要由锐钛矿和金红石2种晶相组成;光催化降解苯酚的效果明显优于直接光解;当苯酚初始浓度为0.98 mg/L时,反应2.5 h后的降解率为86%.     

V/Ce共掺杂TiO2光催化降解甲醛的实验研究

采用溶胶-凝胶法制备了不掺杂、V掺杂、Ce掺杂、V/Ce共掺杂纳米TiO2光催化剂,并将其分别负载于瓷砖上,利用X射线衍射分析（XRD）和扫描电镜分析（SEM）技术对薄膜样品的结构和形貌进行了表征。通过对甲醛的降解实验评价光催化剂的光催化活性。实验结果表明,光催化剂的负载量、共掺杂离子的掺杂量、掺杂配比、煅烧温度影响纳米TiO2的光催化活性。V/Ce共掺杂TiO2光催化剂产生了协同效应,其光催化活性优于纯TiO2和单掺杂TiO2样品。     

Effects of dissolved oxygen, pH, and anions on the 2,3-dichlorophenol degradation by photocatalytic reaction with anodic TiO(2) nanotube films

In this study, the highly-ordered TiO(2) nanotube (TNT) arrays on titanium sheets were prepared by an anodic oxidation method. Under UV illumination, the TNT films demonstrated the higher photocatalytic activity in terms of 2,3-dichlorophenol (2,3-DCP) degradation in aqueous solution than the conventional TiO(2) thin films prepared by a sol-gel method. The effects of dissolved oxygen (DO) and pH on the photocatalytic degradation of 2,3-DCP were investigated. The results showed that the role of DO in the 2,3-DCP degradation with the TNT film was significant. It was found that 2,3-DCP in alkaline solution was degraded and dechlorinated faster than that in acidic solution whereas dissolved organic carbon removal presented an opposite order in dependence of pH. In the meantime, some main intermediate products from 2,3-DCP degradation were identified by a (1)H NMR technique to explore a possible degradation pathway. A major intermediate, 2-chlororesorcinol, was identified from the 2,3-DCP decomposition as a new species compared to the findings in previous reports. Photocatalytic deactivation was also evaluated in the presence of individual anions (NO(3)(-), Cl(-), SO(4)(2-), and H(2)PO(4)(-)). The inhibition degree of photocatalytic degradation of 2,3-DCP caused by these anions can be ranked from high to low as SO(4)(2-)>Cl(-)>H(2)PO(4)(-)>NO(3)(-). The observed inhibition effect can be attributed to the competitive adsorption and the formation of less reactive radicals during the photocatalytic reaction.     

活性炭纤维负载TiO2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响。结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%。     

氮掺杂TiO_2可见光光催化剂的制备及性能

以尿素和钛酸丁酯为原料,通过溶胶-凝胶法低温下制备了高可见光催化活性的氮掺杂TiO2（NDT）光催化剂,采用XRD、TEM、BET和UV-Vis DRS等测试手段对其进行了表征,并在自制光催化反应器中降解甲基橙评价了样品的光催化活性。结果表明,当氮与钛的摩尔比为0.5∶1时,350℃焙烧的样品（NDT350）具有最佳的可见光光谱吸收和光催化活性,该催化剂为锐钛矿晶相,平均粒径为21 nm,比表面积为89.13 m2/g。可见光辐照下,NDT350降解甲基橙的表观反应速率常数为1.381×10-2min-1,是商业P25催化剂的16.85倍。NDT350优良的可见光催化活性与其大的比表面积和强烈的可见光光谱吸收有关。     

Photocatalytic degradation of mixed gaseous carbonyl compounds at low level on adsorptive TiO2/SiO2 photocatalyst using a fluidized bed reactor

An adsorptive silica-supported titania photocatalyst TiO(2)/SiO(2) was prepared by using nanosized titania (anatase) immobilized on silica gel by the sol-gel technique with the titanium tetra isopropoxide as the main raw material and acetic acid as the acid catalyst. Meanwhile the structure and properties of the TiO(2)/SiO(2) photocatalyst were studied by means of many modern analysis techniques such as TEM, XRD, and BET. Gas-solid heterogeneous photocatalytic decomposition of four carbonyl compounds mixture at low concentration levels over ultraviolet irradiated TiO(2)/SiO(2) photocatalyst were carried out with high degradation efficiencies in a coaxial triple-cylinder-type fluidized bed photocatalytic reactor, which provided efficient continuous contact of ultraviolet photons, silica-supported titania photocatalyst, and gaseous reactants. Experimental results showed that the photocatalyst had a high adsorption performance and a good photocatalytic activity for four carbonyl compounds mixture. Some factors influencing the photocatalytic decomposition of the mixed carbonyl compounds, i.e. the gas flowrate, relative humidity, concentration of oxygen, and illumination time, were discussed in detail. It is found that the photocatalytic reaction rate of four carbonyl compounds decreased in this order: propionaldehyde, acetone, acetaldehyde and formaldehyde.     

The preparation of Zn2+-doped TiO(2) nanoparticles by sol-gel and solid phase reaction methods respectively and their photocatalytic activities

The photocatalytic oxidation of the organic pollutants with TiO(2) as photocatalyst has been widely studied in the world, and many achievements have been made. The degradation of pollutants is highly related to the photocatalytic activity of TiO(2). It is demonstrated that doping ions to TiO(2) is one way to enhance the photocatalytic activity of TiO(2). In this paper, Zn(2+)-doped TiO(2) nanoparticles were prepared through sol-gel and solid phase reaction methods, characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by sol-gel method is close to that of pure TiO(2) particles, however, the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by solid phase reaction method is much higher than that of pure TiO(2) particles. The most efficient degradation of Rhodamine B was found with TiO(2) particles doped with 0.5% Zn(2+) in mole and calcined at 500 degrees C. Also the reason for the enhancement of the photocatalytic activity of TiO(2) by Zn(2+) doping through solid phase reaction method was discussed.     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。