染料中间体废水的催化臭氧化预处理

自制了２种高活性的催化剂Ｍｎ－０２和Ｆｅ－Ｎｉ－Ｕｒｅａ,并对典型染料中间体废水－吐氏酸废水进行金属催化臭氧化预处理。对初始ＣＯＤ浓度约为１５００ｍｇ／Ｌ的废水,当臭氧投加量为０．８２ｇ／Ｌ时,ＣＯＤ去除率大于５０％,其臭氧化指分别为１．４４和１．０７,而相应的空白则为１．９０。     

混凝氧化吸附法处理精研精抛清洗废液

采用混凝氧化吸附法处理精研精抛清洗废液，对６种混凝剂的ＰＨ值、投加量及氧化剂Ｈ２Ｏ２的投加量进行了筛选，同时简单地分析了混凝氧化反应机理，经混凝氧化处理后，ＣＯＤ值由１２０００ｍｇ／Ｌ降至５００ｍｇ／Ｌ左右，ＣＯＤ去除率达９５％；最后进行活性碳吸附，ＣＯＤ值达到国家排放标准。     

负载型TiO2固定相光催化氧化法降解水中呋码唑酮

以高压汞灯为光源、负载在海砂上的ＴｉＯ２为催化剂，采用敞口固定床型光催化反应器对水中难降解的呋码唑酮（ＦＴＤ）进行了固定相光催化氧化实验。结果表明，反应速率可用ＬａｎｇｍｕｉｒＨｉｎｓｈｅｌｗｏｏｄ方程描述，与光分解相比，光催化氧化的突出优点是矿化程度高，相同光辐射条件下反应１００ｍｉｎ，０．１０ｍｍｏｌ／Ｌ的ＦＴＤ水溶液经光催化氧化后ＴＯＣ的去除率为８９．１％，而经光分解后ＴＯＣ的去除率仅为２８．８％；在反应体系中投加少量臭氧或过氧化氢可以显著提高ＦＴＤ的氧化效率，说明光催化氧化可以兼容Ｏ３／ＵＶ、Ｈ２Ｏ２／ＵＶ等光激发氧化工艺。制得的负载型ＴｉＯ２具有较高的机械强度和化学稳定性，可重复利用。探讨了充氧、ＦＴＤ浓度及ｐＨ值等对光催化氧化过程的影响。     

光催化氧化法处理染料中间体H酸水溶液

为了去除水中难氧化的有害染料中间体Ｈ酸,研究以ＴＩＯ２、ＺｎＯ、ＣｄＳ和Ｆｅ２Ｏ３为催化剂,采用低压汞灯为光源,对Ｈ酸水溶液进行光催化氧化实验．结果表明：ＴｉＯ２和ＣｄＳ的催化效果最好．采用ＴｉＯ２作催化剂,光催化氧化５ｈ后,Ｈ酸分解率可达９０％,反应速率遵从Ｌａｎｇｍｕｉｒ－Ｈｉｎｓｈｅｌｗｏｏｄ方程,Ｋ＝１２．３Ｌ／ｍｍｏｌ,ｋ＝２５．２×１０－６ｍｏｌ／ｈ．溶液中投加１０ｍｇ／Ｌ的Ｆｅ３＋或Ａｇ＋,可使反应时间缩短２—３ｈ．研究探讨了ｐＨ、ＴｉＯ２投加量和Ｈ酸浓度对催化氧化过程的影响．     

药厂阿斯匹林废水的治理

本文采用铁屑／烟道灰过滤－混凝－臭氧氧化组合工艺处理药厂阿斯匹林废水，ＣＯＤ去除率可达９６．５％，脱色率可达９９．５％，处理后的废水ＣＯＤ低于５０ｍｇ／Ｌ，色度低于２倍，水质清澈透明，各项水质指标均符合国家排放标准。     

Ni,Fe氧化物对吐氏酸废水催化臭氧化研究

用浸渍法和附着沉淀法制备了６种以Ｎｉ、Ｆｅ为活性组分，γＡｌ２Ｏ３载体的国型催化剂，催化臭经处理难生物降解的典型染料中间体废水－吐氏酸废水。初始ＣＯＤｃ浓度为１５００ｍｇ／Ｌ左右的废水，当臭氧投加量为０．８ｇ／Ｌ时，在活性最高的催化剂作用下，ＣＯＤＣｒ去除率大于５０％，而没有催化剂作用时小于３０％。     

生物接触氧化法处理石化废水

介绍了塔器与生物接触氧化技术相结合处理石化污水的新技术。污水经处理后，ＮＨ＋４－Ｎ可以从５０～８０ｍｇ／Ｌ降到１０ｍｇ／Ｌ以下，ＣＯＤ从１００～２００ｍｇ／Ｌ降至８０ｍｇ／Ｌ以下，最短停留时间３     

含硫废水电净化工艺试验研究

对电氧化处理含硫废水的工艺和机理进行了探讨和模拟实验。在容积为１０Ｌ，ｐＨ７０～１００，Ｓ２－浓度５０～１０００ｍｇ／Ｌ，ＣＯＤＣｒ２６０～２７００ｍｇ／Ｌ的无隔离电净化槽液中，温度３０～６０℃，槽压３～５Ｖ，通过电量０８～３６Ａｈ／Ｌ时，脱硫率与ＣＯＤＣｒ去除率分别达９３％和８５％，每ｋｇ硫能耗４９５ｋＷ·ｈ或每污水耗能２００ｋＷ·ｈ。处理成本为氧化脱硫或汽提脱硫的１／３～１／２。     

硝化细菌在氨氮深度处理中的应用研究

通过使用硝化细菌增养液挂膜，用生物接触氧化法对生活污水处理厂出水以及富营养化河水中的氨氮进行了处理。试验结果表明：在很短的水力停留时间条件下（１ｈ），污水厂出水经处理后ＮＨ３－Ｎ全部达标并小于８ｍｇ／Ｌ，其去除率达７０％；ＮＯ＾－２－Ｎ小于４ｍｇ／Ｌ。富营养化河水在ＨＲＴ为１．２ｈ时，出水ＮＨ３－Ｎ与ＮＯ＾－２均小于１ｍｇ／Ｌ。试验出水中的氮主要以ＮＯ＾－３－Ｎ的形式存在。     

[Cu—γ—Al2O3]催化剂处理染料废水工艺条件研究

采用「Ｃｕ－γ－Ａｌ２Ｏ３」催化剂对由活性艳红Ｘ－３Ｂ配制的ＣＯＤｃｒ为５７００ｍｇ／Ｌ色度３１００倍的实际染料废水进行了催化氧化试验，试验表明，在控制ｐＨ＝４－５，Ｈ２Ｏ２用量为５．０ｍｇ／Ｌ，催化剂用量为３．０ｇ／Ｌ，ｔ＝７０℃和反应时间为２ｈ条件下，可获得ＣＯＤｃｒ去除率为７７％－７８％，脱色率为９９％的良好效果，且催化剂可再生使用。     

化学沉淀法去除垃圾渗滤液中的氨氮

为了有效地去除垃圾渗滤液中高浓度的ＮＨ＾＋４－Ｎ而避免传统吹脱法造成吹脱塔内碳酸盐结垢问题,探讨了采用化学药剂诸加ＭｇＣｌ２·６Ｈ２Ｏ和Ｎａ２ＨＰＯ４·１２Ｈ２Ｏ或ＭｇＯ和Ｈ３ＰＯ４使ＮＨ＾＋４－Ｎ生成磷酸铵镁的化学沉淀去除法。小试研究结果表明,当垃圾渗滤液中投加ＭｇＣｌ２·６Ｈ２Ｏ和Ｎａ２ＨＰＯ４·１２Ｈ２Ｏ而使Ｍｇ＾２＋：ＮＨ＾＋４：ＰＯ＾３－４的比例为１：１：１时,在最佳ｐＨ为８．５～９．０     

高级氧化处理苯酚废水的研究

采用Fenton试剂和O3对COD为950mg/L的苯酚废水进行化学氧化处理,通过实验确定各自最佳的运行参数。Fenton:n(H2O2)=36mmol/L,n(H2O2):n(Fe2+)=3,pH为3,反应时间为2h,COD去除率为90%;O3:投加量为1200mg/L,pH为11时COD的去除率为60%,两种氧化技术都有较好的处理效果。     

非均相催化湿式氧化法再生活性炭实验

使用自制的CuO-Al₂O₃催化剂对苯酚饱和活性炭进行非均相催化湿式氧化再生研究,系统观察了反应条件对非均相催化湿式氧化再生活性炭的影响.实验中得到非均相CuO-Al₂O₃催化湿式氧化再生活性炭的最佳条件为:反应温度210℃,反应时间60min,催化剂投加量25mg(以铜离子计),反应氧分压0.6MPa(25℃),投炭量15g(干炭量),加水量300mL.通过对催化剂进行X衍射分析,并对催化剂的稳定性进行实验,可以得出该催化剂在催化湿式氧化再生活性炭的过程中具有较好的稳定性.     

Impact of Fenton and ozone on oxidation of wastewater containing nitroaromatic compounds

Fenton and ozone treatment was investigated at laboratory scale for the degradation of aqueous solutions of nitrobenzene (NB).Effects of reactants concentration (O3,H2O2,and Fe(II)),temperature,and pH on NB degradation were monitored.Reaction kinetic of these processes was also assessed.A rapid reaction took place for Fenton process at higher initial concentration of H2O2,higher temperatures,and more acidic conditions(pH 3).Similarly, ozonation reaction exhibited rapid rates for higher ozone dose,higher temperatures,and more basic conditions(pH 11).Complete NB degradation in 65 min Was achieved using Fenton process.The conditions of complete elimination of 100 mg/L of initial NB concentration,were 250 mg/L of H2O2 concentration,pH 3,and 10 mg/L of Fe(Ⅱ) concentration.Under these conditions,55% organic carbon elimination Was achieved.Total organic carbon mineralization Was attained in 240 min reaction time by Fenton process with 900 mg/L of H2O2 concentration,and 30 mg/L of Fe(II) concentration.Fenton reaction showed a pseudo-first order kinetic;the reaction rate constant Was ranged from 0.0226 to 0.0658 min-1.Complete NB degradation wag also achieyed for an ozone dose of the order of 2.5 g/L.The ozonation Was studied at different ozone doses.different initial pH(7-11)and at difierent temperatures(15-35℃).NB ozonation kinetic Was represented by a bi-molecular kinetic model which was reduced to pseudo-first order kinetic.The pseudo-first order reaction rate constant was determined to increase at 20℃ from 0.004 to 0.020 min-1 as the used ozone increased from 0.4 to 1.9g/L.     

蕉藕淀粉废水絮凝试验

试验采用化学混凝法对蕉藕淀粉加工产生的废水进行处理,研究了硫酸铝,氯化铁,聚合硫酸铁(PSF),聚合氯化铝(PAC),聚丙烯酰胺(PAM)等不同混凝剂种类和投加量对COD、SS和TP去除效果的影响。试验结果表明,聚合氯化铝处理效果最佳,在废水COD、SS和TP的浓度分别为8340mg/L、7060mg/L和320mg/L时聚合氯化铝以500mg/L的用量得到COD、SS和TP的去除率分别为97.1%、98.0%和70%,出水的COD为241mg/L,SS为142mg/L,TP为112mg/L。     

高级氧化-BAF深度处理焦化废水

采用O3+BAF和Fenton+BAF两种工艺去除焦化废水中经生物处理后的残余污染物,考察了O3浓度、pH值、亚铁/双氧水配比、双氧水加入量、曝气时间等影响因素。结果表明,当臭氧加入量为800mg/L,BAF曝气时间为18h,双氧水加入量为0.5mL/L,亚铁为2g/L,出水COD都低于70mg/L,色度低于50倍,达到一级排放标准。     

Photo-assisted fenton oxidation of refractory organics in UASB-pretreated leachate

Nearly 91% of organic pollutants in Hong Kong leachate could be effectively removed by the UASB(upflow anaerobic sludge blanket)process followed by the fenton coagulation.The COD(chemical oxygen demand)of leachate was lowered from an average of 5620 mg/L to 1910 mg/L after the UASB treatment at 37℃,and was further lowered to 513 mg/L after fenton coagulation.The remaining refractory residues could be further removed by plotochemical oxidation with the addition of H2O2.The BOD/COD ratio was greatly increased from 0.062 to 0.142,indicating the biodegradability of organic residues was improved.The photochemical oxidation for the fenton-coagulation supernatant was most effective at pH3-4,with the addition of 800 mg/L of H2O2,and UV radiation time of 30 minutes.The final effluent contained only 148 mg/L of COD,21 mg/L of BOD(biochemical oxygen demand)and 56 mg/L of TOC (total organic carbon).     

O_3/H_2O_2催化氧化对苯二酚的影响因素及急性毒性变化

研究了O_3/H_2O_2催化氧化对苯二酚的去除效果及氧化过程中产物的急性毒性变化情况,并探讨了O_3/H_2O_2催化氧化对苯二酚的反应机理。结果表明:O_3/H_2O_2在中性条件下氧化对苯二酚反应中,通过H_2O_2和O_3分子联合作用(O_3投加量为210 mg/L、H_2O_2投加量为0.15%)可完全去除对苯二酚(浓度为150 mg/L)以及42%的TOC。以污染物在水环境中对发光细菌的抑光率为毒性指标,反应过程中的毒性作用先增大后减小。O_3/H_2O_2氧化是一种高效去除酚类化合物、降低急性毒性的方法,具有良好的应用前景。     

Ozonation of refractory chemicals in leachate with hydrogen peroxide

Nearly 97% of organic chemicals in Hong Kong leachate could be effectively removed by the UASB( upflow anaerobic sludge blanket) process followed by the fenton coagulation. The COD of leachate was lowered from an average of 12900 mg/L to 1440 mg/L after the UASB treatment, and was further lowered to 394 mg/L after the fenton coagulation. The remaining refractory residues could be further removed by ozonation with the addition of H2Oz. The ozonation for the supernatant of the fenton coagulation was most effective at pH 7-8, with the addition of 300 mg/L of H202, and 30 min of reaction. The final effluent contained only 85 mg/L of COD and 10 mg/L of BOD5. On the other hand, direct ozonation of UASB effluent lowered the COD to 905 mg/L and BOD5 to 103 mg/L. Ozonation improved the biodegradability of the organic residues, and also converted oart of oruanic-N in the leachate into NH3-N and NO3^- -N.     

微波诱导催化剂Fe_2O_3/Al_2O_3制备及PEG对其活性影响

以AlCl·36H2O、FeCl·36H2O和CO(NH)22为原料,采用均匀沉淀法制备微波诱导催化剂Fe2O3/Al2O3,用X射线衍射仪(XRD)对其结构进行了表征,研究了加入聚乙二醇(PEG200)作为分散剂对产物的影响。结果表明:加入体积分数为0.05%PEG后,对于20mg/L的甲基橙模拟废水,在微波功率为900W,催化剂投加量为2g/L,处理5min后脱色率可达95.8%。