Wastewater treatment in molasses-based alcohol distilleries for COD and color removal: a review

Molasses-based distilleries are one of the most polluting industries generating large volumes of high strength wastewater. Different processes covering anaerobic, aerobic as well as physico-chemical methods have been employed to treat this effluent. Anaerobic treatment is the most attractive primary treatment due to over 80% BOD removal combined with energy recovery in the form of biogas. Further treatment to reduce residual organic load and color includes various: (i) biological methods employing different fungi, bacteria and algae, and (ii) physico-chemical methods such as adsorption, coagulation/precipitation, oxidation and membrane filtration. This work presents a review of the existing status and advances in biological and physico-chemical methods applied to the treatment of molasses-based distillery wastewater. Both laboratory and pilot/industrial studies have been considered. Furthermore, limitations in the existing processes have been summarized and potential areas for further investigations have been discussed.     

二段混凝沉淀-曝气氧化-砂滤处理印刷电路板废水

探讨印刷电路板废水处理工艺。针对某印刷电路板厂废水水质特点,采用“二段混凝沉淀一曝气氧化一砂滤”工艺对其进行处理。运行结果表明,废水准确分类及预处理、曝气氧化和投加重金属捕捉荆是保证出水达标的重要措施。该工艺处理效果稳定,出水水质低于《污水综合排放标准》（GB8978-1996）中一级标准。本研究为印刷电路板废水的处理提供了一条可行途径。     

Degradation and removal methods of antibiotics from aqueous matrices--a review

Over the past few years, antibiotics have been considered emerging pollutants due to their continuous input and persistence in the aquatic ecosystem even at low concentrations. They have been detected worldwide in environmental matrices, indicating their ineffective removal from water and wastewater using conventional treatment methods. To prevent this contamination, several processes to degrade/remove antibiotics have been studied. This review addresses the current state of knowledge concerning the input sources, occurrence and mainly the degradation and removal processes applied to a specific class of micropollutants, the antibiotics. In this paper, different remediation techniques were evaluated and compared, such as conventional techniques (biological processes, filtration, coagulation, flocculation and sedimentation), advanced oxidation processes (AOPs), adsorption, membrane processes and combined methods. In this study, it was found that ozonation, Fenton/photo-Fenton and semiconductor photocatalysis were the most tested methodologies. Combined processes seem to be the best solution for the treatment of effluents containing antibiotics, especially those using renewable energy and by-products materials.     

超滤技术在含铅废水处理中的实际运用

面对日趋严格的重金属排放标准,许多传统处理技术,如化学沉淀法、生化法、吸附法等,在某种程度上都难以单独胜任.与此同时,膜技术的快速发展为含重金属废水的深度处理提供了一个崭新的方向.某钢丝绳企业采用超滤技术对含铅废水进行深度处理,由于其过滤精度达0.002～0.1μm,可过滤铅离子组成的胶体(0.05～0.1μm范围),...     

Removal of heavy metals in rinsing wastewater from plating factory by adsorption with economical viable materials

The removal of heavy metals from plating factory wastewater with economical materials was investigated by the column method. Montmorillonite, kaolin, tobermorite, magnetite, silica gel and alumina were used as the economical adsorbents to wastewater containing Cd(II), Cr(VI), Cu(II) and Pb(II). This removal method of heavy metals proved highly effective as removal efficiency tended to increase with increasing pH and decrease with increasing metal concentration. The removal percentages by adsorption onto montmorillonite, tobermorite, magnetite, and silica gel showed high values for all metals. From the results for the heat of adsorption, the adsorption process in the present study might be chemisorption. The proposed method was successfully applied to the removal of Cd(II), Cr(VI) and Cu(II) in rinsing wastewater from plating factory in Nagoya City, Aichi Prefecture, Japan. Since the economical adsorbents used can be obtained commercially because they are easily synthesized, the wastewater treatment system developed is rapid, simple and cheap for the removal of heavy metals.     

电化学技术在重金属废水处理中应用

电化学法处理重金属废水，就是在直流电作用下，利用电极反应和重金属离子在溶液中的迁移来实现对废水的净化。电化学处理技术能实现废水的处理和重金属的资源化，降低废水处理成本，在重金属废水处理中有着较好的应用前景。     

壳聚糖吸附处理废水的研究进展

壳聚糖吸附处理废水的研究包括其对废水吸附性能和吸附机理的研究两个方面。壳聚糖表现出了良好的吸附废水中重金属离子、染料分子和其它易引起变异物质的能力;壳聚糖对金属离子和染料的吸附机理模型研究理论意义重大,它将进一步推动壳聚糖的实际工程应用。     

酸改性活性炭在重金属与氨氮废水处理中的应用

重金属以及氨氮是造成水体污染的重要物质,在对水体重金属以及氨氮的去除方法中,活性炭吸附法有一定的进展.本文参照常见的酸类物质如硝酸、盐酸、硫酸、磷酸、柠檬酸和其他酸性物质对活性炭改性去除重金属和氨氮的研究,综述了各种酸改性的机理和对活性炭的影响,定性地比较了活性炭在各种酸改性后的去除能力.总结了对酸性改性活性炭在去除重金属和氨氮应用中的发展方向和前景,对于日后用酸性废水改性活性炭以达到以废治废的功效有着指导、借鉴作用.     

重金属废水处理技术研究进展

总结近年来重金属废水主要处理技术,指出重金属废水污染治理与重金属的回收利用相结合是未来治理的发展之路,也是技术开发与应用的方向。     

重金属废水生化处理技术的研究进展

处理重金属废水的传统方法在投资和运行费用上都较高，加之沉淀去除效果不太理想，近年来国内外进行了大量的生化法去除重金属的研究。本文介绍了生物吸附法、生物絮凝法、微生物代谢法和植物吸收法。生化法处理重金属废水，成本低，效益高，易管理，可回收重金属，有利于生态环境的改善，具有十分广阔的应用前号。     

Prediction of metal-adsorption behaviour in the remediation of water contamination using indigenous microorganisms

In recent years, the adsorption of heavy metal cations onto bacterial surfaces has been studied extensively. This paper reports the findings of a study conducted on the heavy metal ions found in mine effluents from a mining plant where Co²⁺ and Ni²⁺ bearing minerals are processed. Heavy metal ions are reported to be occasionally present in these mine effluents, and the proposed microbial sorption technique offers an acceptable solution for the removal of these heavy metals. The sorption affinity of microorganisms for metal ions can be used to select a suitable microbial sorbent for any particular bioremediation process. Interactions of heavy metal ions (Co²⁺ and Ni²⁺) and light metal ions (Mg²⁺ and Ca²⁺) with indigenous microbial cells (Brevundimonas spp., Bacillaceae bacteria and Pseudomonas aeruginosa) were investigated using the Langmuir adsorption isotherm, pseudo second-order reaction kinetics model and a binary-metal system. Equilibrium constants and adsorption capacities derived from these models allowed delineation of the effect of binding affinity and metal concentration ratios on the overall adsorption behaviour of microbial sorbents, as well as prediction of performance in bioremediation systems. Although microbial sorbents used in this study preferentially bind to heavy metal ions, it was observed that higher concentrations (>90 mg/?) of light metal ions in multi-metal solutions inhibit the adsorption of heavy metal ions to the bacterial cell wall. However, the microbial sorbents reduced Ni²⁺ levels in the mine-water used (93–100% Ni²⁺ removal) to below the maximum acceptable limit of 350 μg/?, established by the South African Bureau of Standards. Competition among metal ions for binding sites on the biomaterial surface can occur during the bioremediation process, but microbial sorption affinity for heavy metal ions can enhance their remediation in dilute (<5 mg/? heavy metal) wastewaters.     

Environmental management aspects for TBT antifouling wastes from the shipyards

Tributyltin (TBT)-based antifouling paints have been successfully used for over 40 years to protect a ship's hull from biofouling. However, due to its high toxicity to marine organisms, the International Maritime Organization (IMO), in 1990, adopted a resolution recommending governments to adopt measures to eliminate antifouling paints containing TBT. High concentrations of TBT are detected in the vicinity of ports and shipyards. TBT is also usually detected in the sediment, in which it accumulates. This study reviews recent literature for the best management practices (BMPs) in order to minimize the environmental effects of TBT. The paper focuses on the evaluation of the available techniques for the removal of TBT from shipyard wastes and from the sediment. The most effective treatment methods are highlighted. BMPs include recycling of abrasive materials, use of cleaner abrasive materials, reuse of spent abrasive materials, substitution of hydroblasting by vacuum blasting or containment or ultra-high-pressure water blasting and confinement of pollution by enclosure and containment systems. The treatment of the TBT wastes by conventional biological wastewater treatment processes is probably not suitable, because the concentrations of TBT found in shipyards' wastewaters are toxic to microorganisms. Advanced technologies such as activated carbon adsorption and dissolved air flotation, in combination with filtration and coagulation-clarification, photodegradation and electrochemical treatment, are required to remove TBT. However, advanced methods should be further optimized to meet the regulatory limit of 200 ng/L. To date, only one published work examines the efficiency of incineration for the treatment of solid sandblast wastes. Regarding the treatment of sediment, land deposition of the less polluted fraction of sediment is a feasible option. Such treatment must take into account the risk of contamination of groundwater and the surroundings, and it requires extended areas of land. Other treatment methods, such as thermal and electrochemical treatment, are promising options but due to the large amounts of dredged material, they have high capital and operational costs.     

水体重金属污染治理技术研究进展

随着工业的发展和人口的不断增加,重金属废水排放量增加。有毒重金属对环境的严重威胁正逐渐成为全球性问题,不仅对环境造成危害,还威胁着人类的健康。介绍了水体重金属污染现状及危害,综述了目前国内外治理水体重金属污染主要技术的研究进展,指出了微生物治理重金属污染水体的良好应用前景。     

FGD脱硫废水处理工艺及其优化设计

阐述了脱硫废水中污染物的去除机理,介绍了化学-机械沉降去除脱硫废水中悬浮物、重金属元素等物质的废水处理工艺,并对脱硫废水处理系统的优化设计进行了重点论述。     

Application of low-cost adsorbents for dye removal – A review

Dyes are an important class of pollutants, and can even be identified by the human eye. Disposal of dyes in precious water resources must be avoided, however, and for that various treatment technologies are in use. Among various methods adsorption occupies a prominent place in dye removal. The growing demand for efficient and low-cost treatment methods and the importance of adsorption has given rise to low-cost alternative adsorbents (LCAs). This review highlights and provides an overview of these LCAs comprising natural, industrial as well as synthetic materials/wastes and their application for dyes removal. In addition, various other methods used for dye removal from water and wastewater are also complied in brief. From a comprehensive literature review, it was found that some LCAs, in addition to having wide availability, have fast kinetics and appreciable adsorption capacities too. Advantages and disadvantages of adsorbents, favourable conditions for particular adsorbate–adsorbent systems, and adsorption capacities of various low-cost adsorbents and commercial activated carbons as available in the literature are presented. Conclusions have been drawn from the literature reviewed, and suggestions for future research are proposed.     

Evaluation of a low-cost adsorbent for removal of toxic metal ions from wastewater of an electroplating factory

In this study, sugar cane residue or bagasse was used for removal of toxic metal ions from wastewater of an electroplating factory located in northeast Brazil. Prior acid treatment increased the adsorption efficacies in batch wise experiments. The microstructure of the material before and after the treatment was investigated by X-ray diffraction, infrared spectroscopy and scanning electron microscopy. Column operations showed that removals of Cu²⁺, Ni²⁺ and Zn²⁺ from wastewater (in the absence of cyanide) were 95.5%, 96.3.0%, and 97.1%, respectively. Regeneration of the adsorbent obtained in acid indicated that the efficiencies decreased only after the fourth cycle of re-use. Acid-treated sugar cane bagasse can be considered a viable alternative to common methods to remove toxic metal ions from aqueous effluents of electroplating industries.     

不同物质对垃圾渗滤液中腐殖酸的吸附研究

垃圾渗滤液是一种有毒有害的高浓度有机废水,其中含大量腐殖酸。腐殖酸具有离子交换能力、吸附能力和脱除杂质能力,因此在很多方面有实用价值。活性碳、土壤、堆肥对废水中的有机物有一定的吸附能力。本文采用正交设计的方法,研究了活性碳、土壤、堆肥在不同温度,液／固,腐殖酸初始浓度的条件下对垃圾渗滤液中腐殖酸的吸附效果。实验结果表明：四种实验因素对吸附剂的吸附能力的影响程度为：吸附剂类型〉腐殖酸的初始浓度〉吸附反应温度〉液固比。在温度为25℃,液固比为50／0．5（mL/g）,腐殖酸初始浓度为41．99（mg／L）,吸附剂类型为活性碳时,腐殖酸吸附量最大,为40．86mg。同时分析了响应指标随因素的变化趋势。     

Reuse of wastewater for industrial needs: the Pontedera case

This paper presents result from an economic and technical point of view evaluation study, which has sought to establish the potential for replacing well-water that is currently used at the Piaggio industrial plant in Pontedera with recycled wastewater. The study is based upon a pilot wastewater treatment plant, which has been used to test wastewater treatment processes and to compare with achieved quality of recycled waters with that of water drawn on-site from physical/chemical pre-treatment and end with a reverse osmosis and air stripping stage. However, after the physical/chemical pre-treatment, the first option uses oxidation with ozone followed by activated carbon filtration, whereas the second method uses ultrafiltration. The first method is more effective at reducing chemical oxygen demand (COD) whereas the second method is more effective in removing bacteria. Nonetheless, both methods deliver water for re-use of a quality comparable with or better than that of well-water. In principle, the reverse osmosis permeate from either process could be re-used in all production phases at the industrial plant. However, the method base upon oxidation with ozone followed by activated carbon filtration is preferred, because, the process is simpler and continuous. The economic analysis of this process gives an estimated cost of Euro 0.55 per m³ for treated water. This compares favorably with other treatment processes and with the cost of other forms of water supply, which are projected to increase in any case.     

染料废水物理化学处理技术的现状与进展

本文按吸附、膜滤、混凝、氧化刑、离子交换、Fenton试剂、光催化氧化、湿式氧化、电化学等方法分别论述了染料废水物理化学处理技术的现状和发展趋势。     

现代厌氧反应器的现状与发展

回顾了厌氧反应器发展的三个阶段，对现代反应器的结构与应用情况进行了详细的介绍，认为目前主要研究与应用的热点是以现代反应器为代表的工艺；以膜技术和分阶段多相多级技术将是未来污水处理技术的主导技术；以复合反应器代表的工艺在处理城市生活污水，处理垃圾渗滤液以及有毒物质废水等将具有更多的优势。在能源资源短缺、环境日益恶化的今天，处理能力强、适用范围广、耗能少等优点的厌氧反应器有着广泛的应用前景与研究价值。