Electro-migration of heavy metals in an aged electroplating contaminated soil affected by the coexisting hexavalent chromium

Cr(VI) was often reported to oxidize soil organic matter at acidic environments due to its high ORP, probably thus changing cationic metal species bound to soil organic matter, and influencing their electro-migration patterns. However, such an effect on the electro-migration was not confirmed in most previous studies. Therefore, this study applied a fixed voltage direct current field on an aged electroplating contaminated clayed soil, with a special interest in the direct or indirect influence of Cr(VI) on the electro-migration of other coexisting metals. After 353 h electrokinetic process, 81% of Zn, 53% of Ni and 22% of Cu in the original soil were electro-migrated into the electrolyte, and most of the remaining concentrated near the cathode. The Cr(VI) oxidized some soil organic matter along its migration pathway, with a pronounced reaction occurred near the anode at low pHs. The resulting Cr(III) reversed its original movement, and migrated towards the cathode, leading to the occurrence of a second Cr concentration peak in the soil. Metal species analyses showed that the amount of metals bound to soil organic matter significantly decreased, while a substantial increase in the Cr species bound to Fe/Mn (hydro-)oxides was observed, suggesting an enhancement of cationic metal electro-migration by the reduction of Cr(VI) into Cr(III). However, the Cr(VI) may form some stable lead chromate precipitates, and in turn demobilize Pb in the soil, as the results showed a low Pb removal and an increase in its acid-extractable and residual fractions after electrokinetic remediation.     

Trivalent chromium solubility and its influence on quantification of hexavalent chromium in ambient particulate matter using EPA method 6800

Measurement of carcinogenic Cr(VI) in ambient PM is challenging due to potential errors associated with conversion between Cr(VI) (a carcinogen) and Cr(III) (an essential nutrient). Cr(III) conversion is a particular concern due to its >80% atomic abundance in total Cr. U.S. Environmental Protection Agency (EPA) method 6800 that uses water-soluble isotope spikes can be used to correct the interconversion. However, whether the enriched Cr(III) isotope spikes can adequately mimic the Cr(III) species originally in ambient PM is unknown. This study examined the water solubility of Cr(III) in ambient PM and discussed its influence on Cr(VI) measurement. Ambient PM₁₀ samples were collected on Teflon filters at four sites in New Jersey that may have different Cr emission sources. The samples were ultrasonically extracted with 5 mL DI-H₂O (pH 5.7) at room temperature for 40 min, and then analyzed by ion chromatography–inductively coupled plasma mass spectrometry (IC-ICPMS). Cr(III) was below detection limit (0.06 ng/m³) for all samples, suggesting water-soluble Cr(III) species, such as CrCl₃, Cr(NO₃)₃, and amorphous Cr(OH)₃, in the ambient PM were negligible. Therefore, the enriched ⁵⁰Cr(III) isotope spike (in the form of Cr(NO₃)₃) could not mimic the original ambient Cr(III). Only the conversion of ⁵³Cr(VI) (in the form of K₂CrO₄) was taken into account when correcting the interconversion. We then used NaHCO₃-pretreated MCE filters (prespiked with enriched isotope species) to measure Cr(VI) in the ambient PM₁₀. The samples were ultrasonically extracted at 60 C pH 9 solutions for 40 min followed by IC-ICPMS analysis. Due to the correction of Cr(VI) reduction, the Cr(VI) concentrations determined by EPA method 6800, 0.26 ± 0.16 (summer) and 0.16 ± 0.11(winter) ng/m³ (n = 64), were significantly greater than those by the external standard curve, 0.21 ± 0.17 (summer) and 0.10 ± 0.07 (winter) ng/m³ (n = 56) (p < 0.01, Student’s t-test). Our study revealed that appropriate application of EPA method 6800 is important because it only applies to soluble fraction of Cr species in ambient PM.

ImplicationsAccurate measurement of carcinogenic Cr(VI) in ambient PM is challenging due to conversion between Cr(VI) (a human carcinogen) and Cr(III) (a human essential nutrient). The conversion of Cr(III) is of particular concern due to its dominant presence in total Cr (>80%). This study examined the water solubility of Cr(III) in ambient PM that was collected at four locations in New Jersey. Then we discussed the influence of Cr(III) solubility on the application of EPA method 6800, which utilizes enriched isotope spikes to correct the interconversion. Our results suggested that appropriate application of EPA method 6800 is important because it only applies to soluble fraction of Cr species.     

Terrestrial and aquatic ecotoxicity assessment of Cr(VI) by the ReCiPe method calculation (LCIA): application on an old industrial contaminated site

The most stable forms of chromium in the environment are chromium (III) and chromium (VI), the former being relatively immobile and necessary for organisms, and the latter being highly soluble and toxic. It is thus important to characterise ecotoxicological impacts of Cr(VI). However, there are still some important uncertainties in the calculation of ecotoxicological impacts of heavy metals in the LCIA global approach. The aim of this paper is to understand how the spatial and dynamic characterization of life cycle inventory (LCI) data can be exploited in life cycle impact assessment and particularly for the evaluation of the aquatic and terrestrial ecotoxicity of Cr(VI). To quantify these impacts, we studied an industrial waste landfill in the North of France that was contaminated with chromium. On the polluted area, the aquatic contamination is due to the slag heap as well as to chromium spots in soil. The soil contamination is mainly due to infiltration of chromium from the infill. The concentration of Cr(VI) in soil and water varies according to seasonal climatic variations and groundwater level. These variations have an effect on the Cr(VI) fate factor, in particular on transfer and residence time of the substance. This study underlines the spatial distribution of aquatic ecotoxicity and the temporal variation of freshwater ecotoxicity. We analysed the correlation between precipitation, temperature, concentration and ecotoxicity impact. With regards to the terrestrial ecotoxicity, the study focused on the vertical variation of the ecotoxicity and the major role of the soil layer composition into terrestrial pollution.     

Graphical estimation of the dual-enzyme kinetic parameters for Cr(VI) reduction

Chromium(VI) (Cr(VI)) contamination of soil and groundwater is a major environmental concern. Bioreduction of Cr(VI) by Shewanella oneidensis MR-1 (MR-1) can be considered a feasible option to reduce the toxic and mobile Cr(VI) to the less toxic and less mobile chromium(III) (Cr(III)). The reaction rate expression for Cr(VI) reduction is nonlinear and the rate constants are evaluated by employing nonlinear optimization techniques. The outcome of the optimization techniques, in general, depends on the initial estimate of the kinetic parameters which is not always available. A graphical approach based on sound mathematical reasoning has been developed which is accurate, simpler to use, and can provide the best initial estimate for nonlinear optimization.     

Chromium speciation in river sediment pore water contaminated by tannery effluent

Cr(VI) is far more soluble and toxic than Cr(III). Sediment pore water was investigated in a river adjacent to the property of a large former tannery, into which Cr-contaminated effluent was discharged over a 55-year period, and where extremely high Cr concentrations have been found in the sediments. Dialysis cells, or peepers, were used to generate depth profiles of Cr concentration in sediment pore water. Samples were analyzed for total Cr using inductively coupled plasma-mass spectrometry (ICP-MS) and for Cr species using high performance liquid chromatography (HPLC)-ICP-MS. The results show an absence of Cr(VI) in all samples. Furthermore, incomplete recovery of Cr(VI) added to the samples collected at the locations with highest sediment Cr concentrations indicate strong reducing conditions at those locations, which are not conducive to the presence of Cr(VI).     

Effect of chromium species on phytochemical and physiological parameters in Datura innoxia

In soil, chromium can be found in two main valence states: hexavalent Cr(VI) and trivalent Cr(III). In this study, we investigated the impact of Cr on photosynthetic gas exchange, photosystem II (PSII) activity, Cr translocation and accumulation, proline content and alkaloids production, i.e. scopolamine and hyoscyamine, in Datura innoxia. Cr uptake was influenced by its oxidation state and its concentration in growth medium. The plant roots were determined as being the main organ of Cr accumulation. Cr(VI) was more toxic than Cr(III) as indicated by reduction in plant biomass and net photosynthesis. The stomatal conductance showed a similar trend to that of photosynthetic capacity. Cr(III) and Cr(VI) had a different impact on substomatal CO(2) concentration then Cr toxicity was related to its oxidation states. In plants stressed with a Cr(VI) excess, a down regulation of PSII activity was observed with an impairment of photochemical activity. Indeed, the maximum quantum yield of PSII (F(v)/F(m)), the quantum yield of PSII (PhiPSII) and the efficiency of excitation capture by open centers (F'(v)/F'(m)) decreased. Cr(III) had little effects on PSII primary photochemistry, whatever its form induces an increase of scopolamine content without changes in hyoscyamine content in leaves of D. innoxia. These results provide that chromium contamination can change the secondary metabolites composition of leaves, thereby, impacting the quality, safety and efficacy of natural plant products synthesized by D. innoxia plants.     

Cr(VI) uptake mechanism of Bacillus cereus

In this study, we investigated the Cr(VI) uptake mechanism in an indigenous Cr(VI)-tolerant bacterial strain -Bacillus cereus through batch and microscopic experiments. We found that both the cells and the supernatant collected from B. cereus cultivation could reduce Cr(VI). The valence state analysis revealed the complete transformation from Cr(VI) into Cr(III) by living B. cereus. Further X-ray absorption fine structure and Fourier transform infrared analyses showed that the reduced Cr(III) was coordinated with carboxyl and amido functional groups from either the cells or supernatant. Scanning electron microscopy and atomic force microscopy observation showed that noticeable Cr(III) precipitates were accumulated on bacterial surfaces. However, Cr(III) could also be detected in bacterial inner portions by using transmission electron microscopy thin section analysis coupled with energy dispersive X-ray spectroscopy. Through quantitative analysis of chromium distribution, we determined the binding ratio of Cr(III) in supernatant, cell debris and cytoplasm as 22%, 54% and 24%, respectively. Finally, we further discussed the role of bacterium-origin soluble organic molecules to the remediation of Cr(VI) pollutants.     

In situ remediation of soils contaminated with toxic metal ions using microwave energy

Following onto our work on the in situ remediation of soils contaminated with PAH's, PCB's and other polychlorinated organic compounds using microwave energy, we now report a preliminary investigation on the in situ remediation of soils contaminated with toxic metal ions: Cd(II), Mn(II), Th(IV), Cr(III) and mainly Cr(VI). The soil is partially vitrified in the process, and extraction with hot (70 degrees C) 35% nitric acid for 4.5 h leads to the recovery of very small amounts of the metals which had been spiked into the clean soil: Cd, Mn, and Cr(III) are completely immobilized (unextractable), Th is mostly unextractable, and Cr(VI) partially extractable at very high levels of spiking, but almost completely unextractable using the US EPA Toxicity Characteristic Leaching Procedure. This suggests that contaminated soils which are not going to be used for agricultural purposes can be remediated safely to preset depths without fear of the toxic metal ions leaching out for a long time.     

Chromium species behaviour in the activated sludge process

The purpose of this research was to compare trivalent chromium (Cr(III)) and hexavalent chromium (Cr(VI)) removal by activated sludge and to investigate whether Cr(VI) reduction and/or Cr(III) oxidation occurs in a wastewater treatment system. Chromium removal by sludge harvested from sequencing batch reactors, determined by a series of batch experiments, generally followed a Freundlich isotherm model. Almost 90% of Cr(III) was adsorbed on the suspended solids while the rest was precipitated at pH 7.0. On the contrary, removal of Cr(VI) was minor and did not exceed 15% in all experiments under the same conditions. Increase of sludge age reduces Cr(III) removal, possibly because of Cr(III) sorption on slime polymers. Moreover, the decrease of suspended solids concentration and the acclimatization of biomass to Cr(VI) reduced the removal efficiency of Cr(III). Batch experiments showed that Cr(III) cannot be oxidized to Cr(VI) by activated sludge. On the contrary, Cr(VI) reduction is possible and is affected mainly by the initial concentration of organic substrate, which acts as electron donor for Cr(VI) reduction. Initial organic substrate concentration equal to or higher than 1000 mgl(-1) chemical oxygen demand permitted the nearly complete reduction of 5 mgl(-1) Cr(VI) in a 24-h batch experiment. Moreover, higher Cr(VI) reduction rates were obtained with higher Cr(VI) initial concentrations, expressed in mg Cr(VI) g(-1) VSS, while decrease of suspended solids concentration enhanced the specific Cr(VI) reduction rate.     

Mechanisms of chromium and arsenite adsorption by amino-functionalized SBA-15

The adsorption of Cr(VI) and As(III) by amino-functionalized SBA-15 (NH₂-SBA-15) from single and binary systems were investigated in this work. The effects of pH and temperature on the adsorption of NH₂-SBA-15 were studied. Adsorption kinetics, isotherm model, and thermodynamics were studied to analyze the experimental data. pH 2 was the optimum condition for the adsorption of Cr(VI) and pH 4 for As(III) adsorption. Increasing temperature had a positive effect on the removal of both Cr(VI) and As(III). The Freundlich isotherm model can depict the adsorption process best. The pseudo-second-order kinetic model fitted well with the kinetic data of Cr(VI) and As(III) in the single-component system. In the binary system, the adsorption of As(III) by NH₂-SBA-15 was slightly enhanced with the presence of Cr(VI); however, As(III) had no obvious effect on the removal of Cr(VI). Regeneration experiments indicated that 0.1 mol/L NaHCO₃ was an efficient desorbent for the recovery of Cr(VI) and As(III) from NH₂-SBA-15; the desorption rates for Cr(VI) and As(III) were 91.6 and 33.59 %, respectively. After five recycling cycles, the removal rates were 88 and 7 % for Cr(VI) and As(III) adsorption by NH₂-SBA-15, respectively.     

Investigation of the removal mechanism of Cr(VI) in groundwater using activated carbon and cast iron combined system

Zero-valent iron (Fe⁰) has been widely used for Cr(VI) removal; however, the removal mechanisms of Cr(VI) from aqueous solution under complex hydrogeochemical conditions were poorly understood. In this research, the mixed materials containing cast iron and activated carbon were packed in columns for the treatment of aqueous Cr(VI)-Cr(III) in groundwater with high concentration of Ca²⁺, Mg²⁺, HCO₃ ⁻, NO₃ ⁻, and SO₄ ²⁻. We investigate the influences of those ions on Cr(VI) removal, especially emphasizing on the reaction mechanisms and associated precipitations which may lead to porosity loss by using X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) techniques. The results show that the precipitations accumulated on the material surface were (Fe/Cr) (oxy)hydroxide, mixed Fe(III)-Cr(III) (oxy)hydroxides, Fe₂O₃, CaCO₃, and MgCO₃. During these reactions, the Cr(VI) was reduced to Cr(III) coupled with the oxidated Fe⁰ to Fe(II) through the galvanic corrosion formed by the Fe⁰-C and/or the direct electron transfer between Fe⁰ and Cr(VI). In addition, Cr(VI) could be reduced by aqueous Fe(II), which dominated the whole removal efficiency. The primary aqueous Cr(III) was completely removed together with Cr(III) reduced from Cr(VI) even when Cr(VI) was detected in the effluent, which meant that the aqueous Cr(III) could occupy the adsorption sites. In general, the combined system was useful for the Cr(VI)-Cr(III) treatment based on galvanic corrosion, and the hardness ions had a negative effect on Cr(VI) removal by forming the carbonates which might promote the passivation of materials and decrease the removal capacity of the system.

     

Kinetics of the reduction of hexavalent chromium with the brown seaweed Ecklonia biomass

The dead biomass of the brown seaweed, Ecklonia sp., is capable of reducing toxic Cr(VI) into less toxic or nontoxic Cr(III). However, little is known about the mechanism of Cr(VI) reduction by the biomass. The objective of this work was to develop a kinetic model for Cr(VI) biosorption, for supporting our mechanism. The reduction rate of Cr(VI) increased with increasing total chromate concentration, [Cr(VI)], and equivalent concentration of organic compounds, [OCs], and decreasing solution pH. It was found that the reduction rate of Cr(VI) was proportional to [Cr(VI)] and [OCs], suggesting the simple kinetic equation -d[Cr(VI)]/dt=k[Cr(VI)][OCs]. When considering the consumption of organic compounds due to the oxidation by Cr(VI), an average rate coefficient of 9.33 (+/-0.65)microM(-1)h(-1) was determined, at pH 2. Although the function of the pH could not be expressed in a mechanistic manner, an empirical model able to describe the pH dependence was obtained. It is expected that the developed rate equation could likely be used for design and performance predictions of biosorption processes for treating chromate wastewaters.     

Chromium accumulation by the hyperaccumulator plant Leersia hexandra Swartz

Leersia hexandra Swartz (Gramineae), which occurs in Southern China, has been found to be a new chromium hyperaccumulator by means of field survey and pot-culture experiment. The field survey showed that this species had an extraordinary accumulation capacity for chromium. The maximum Cr concentration in the dry leaf matter was 2978 mg kg(-1) on the side of a pond near an electroplating factory. The average concentration of chromium in the leaves was 18.86 times as that in the pond sediment, and 297.41 times as that in the pond water. Under conditions of the nutrient solution culture, it was found that L. hexandra had a high tolerance and accumulation capacity to Cr(III) and Cr(VI). Under 60 mg l(-1) Cr(III) and 10 mg l(-1) Cr(VI) treatment, there was no significant decrease of biomass in the leaves of L. hexandra (p>0.05). The highest bioaccumulation coefficients of the leaves for Cr(III) and Cr(VI) were 486.8 and 72.1, respectively. However, L. hexandra had a higher accumulation capacity for Cr(III) than for Cr(VI). At the Cr(III) concentration of 10 mg l(-1) in the culture solution, the concentration of chromium in leaves was 4868 mg kg(-1), while at the same Cr(VI) concentration, the concentration of chromium in leaves was only 597 mg kg(-1). These results confirmed that L. hexandra is a chromium hyperaccumulator which grows rapidly with a great tolerance to Cr and broad ecological amplitude. This species could provide a new plant resource that explores the mechanism of Cr hyperaccumulation, and has potential for usage in the phytoremediation of Cr-contaminated soil and water.     

Arsenic and chromium speciation in an urban contaminated soil

The distribution and speciation of As and Cr in a contaminated soil were studied by synchrotron-based X-ray microfluorescence (μ-XRF), microfocused X-ray absorption spectroscopy (μ-XAS), and bulk extended X-ray absorption fine structure spectroscopy (EXAFS). The soil was taken from a park in Wilmington, DE, which had been an important center for the leather tanning industry along the Atlantic seaboard of the United States, until the early 20th century. Soil concentrations of As, Cr, and Pb measured at certain locations in the park greatly exceeded the background levels of these heavy metals in the State of Delaware. Results show that Cr(III) and As(V) species are mainly present in the soil, with insignificant amounts of Cr(VI) and As(III). Micro-XRF maps show that Cr and Fe are distributed together in regions where their concentrations are diffuse, and at local spots where their concentrations are high. Iron oxides, which can reduce Cr(VI) to Cr(III), are present at some of these hot spots where Cr and Fe are highly concentrated. Arsenic is mainly associated with Al in the soil, and to a minor extent with Fe. Arsenate may be sorbed to aluminum oxides, which might have transformed after a long period of time into an As-Al precipitate phase, having a structure and chemical composition similar to mansfieldite (AlAsO(4)?2H(2)O). The latter hypothesis is supported by the fact that only a small amount of As present in the soil was desorbed using the characteristic toxicity leaching procedure tests. This suggests that As is immobilized in the soil.     

The applicability of compost,zeolite and calcium oxide in assisted remediation of acidic soil contaminated with Cr(III) and Cr(VI)

Environmental Science and Pollution Research - The effect of soil amendments, i.e., compost, zeolite, and calcium oxide, on the chemical properties of soil contaminated with Cr(III) and Cr(VI) and...     

Transient behavior of heavy metals in soils during electrokinetic remediation

This paper presents a systematic bench-scale laboratory study performed to assess the transient behavior of chromium, nickel, and cadmium in different soils during electrokinetic remediation. A series of laboratory electrokinetic experiments was conducted using two different clayey soils, kaolin and glacial till. For each type of soil, four electrokinetic experiments with 1, 2, 4, and 10 d of treatment time were performed. In all tests, the contaminants were Cr(VI), Ni(II), and Cd(II) combined in the soil. A geochemical assessment was performed using the geochemical model MINEQL(+) to determine the partitioning of the heavy metals in soils as precipitated, adsorbed, and aqueous forms. Results showed that in kaolin, the extent of Ni(II) and Cd(II) migration towards the cathode increased as the treatment time increased. Unlike kaolin, in glacial till treatment time had no effect on nickel and cadmium migration because of its high buffering capacity. In both kaolin and glacial till, the extent of Cr(VI) migration towards the anode increased as the treatment time increased. However, Cr(VI) migration was higher in glacial till as compared to kaolin because of the high pH conditions that existed in glacial till. In all tests, some Cr(VI) was reduced to Cr(III), and the Cr(VI) reduction rate to Cr(III) as well as the Cr(III) migration were significantly affected by the treatment time. Overall, this study showed that the electroosmotic flow as well as the direction and extent of contaminant migration and removal depend on the polarity of the contaminant, the type of soil, and the treatment duration.     

Phytotoxic lesions of chromium in maize

Chromium (Cr) is fairly abundant in the earth's crust and ranks fourth among the 29 elements of biological importance. Besides natural sources, Cr enters biotic components of the ecosystem in various ways. Of other major industrial sources, tanning and chrome-plating industries are prominent sources. Cr(VI) form of chromium is highly reactive and influences both plants and animals. Due to Mn present in soil, Cr(III) is oxidized to Cr(VI) which remains in soil for a long time and can affect plant growth and development. Since maize is an important food and fodder plant for human beings and cattle, a study was conducted to investigate the effects of Cr on some metabolic activities of maize (Zea mays L. cv. Ganga 5). Chromium caused visible lesions of interveinal chlorosis. Young leaves showed vein clearing. Also, a papery appearance was observed in leaves. Margins of leaves were curled and the leaves appeared pale at greater Cr exposure. Concentrations of both chlorophyll a and b were reduced by exposure to Cr, the activities of ribonuclease and phenyl phosphatase were greater while the activity of iron-porphyrin enzyme catalase was less and the activity of amylase was also much less in plants exposed to Cr. Chromium also caused retardation of soluble protein. Accumulation of Cr in roots was much at all the levels of chromium supply. Exposure to Cr resulted in reduction in grain production and quality.     

Chromium transport, oxidation, and adsorption in manganese-coated sand

We examine how the processes of advection, dispersion, oxidation-reduction, and adsorption combine to affect the transport of chromium through columns packed with pyrolusite (beta-MnO2)-coated sand. We find that beta-MnO2 effectively oxidizes Cr(III) to Cr(VI) and that the extent of oxidation is sensitive to changes in pH, pore water velocity, and influent concentrations of Cr(III). Cr(III) oxidation rates, although initially high, decline well before the supply of beta-MnO2 is depleted, suggesting that a reaction product inhibits the conversion of Cr(III) to Cr(VI). Rate-limited reactions govern the weak adsorption of each chromium species, with Cr(III) adsorption varying directly with pH and Cr(VI) adsorption varying inversely with pH. The breakthrough data on chromium transport can be matched closely by calculations of a simple model that accounts for (1) advective-dispersive transport of Cr(III), Cr(VI), and dissolved oxygen, (2) first-order kinetics adsorption of the reduced and oxidized chromium species, and (3) nonlinear rate-limited oxidation of Cr(III) to Cr(VI). Our work supplements the limited database on the transport of redox-sensitive metals in porous media and provides a means for quantifying the coupled processes that contribute to this transport.