NDA-66树脂对邻苯二甲酸的吸附及脱附性能

研究了NDA-66新型超高交联树脂对邻苯二甲酸的吸附及脱附性能。实验结果表明：静态吸附过程中,在初始邻苯二甲酸质量浓度1 000 mg/L、溶液pH=2.0、吸附时间600 min的条件下,吸附量可达190 mg/g;动态吸附过程中,处理11吸附床层体积倍数（BV）的邻苯二甲酸溶液,当溶液流量为1.5 BV/h时,吸附率可达100%;动态脱附过程中,在w（NaOH）= 6%、脱附温度328 K的最佳脱附条件下,脱附率可达99%以上。     

NDA-66树脂对邻苯二甲酸的吸附及脱附性能

研究了NDA-66新型超高交联树脂对邻苯二甲酸的吸附及脱附性能。实验结果表明:静态吸附过程中,在初始邻苯二甲酸质量浓度1 000 mg/L、溶液pH=2.0、吸附时间600 min的条件下,吸附量可达190 mg/g;动态吸附过程中,处理11吸附床层体积倍数(BV)的邻苯二甲酸溶液,当溶液流量为1.5 BV/h时,吸附率可达100%;动态脱附过程中,在w(NaOH)=6%、脱附温度328 K的最佳脱附条件下,脱附率可达99%以上。     

HZ-16型大孔树脂吸附处理含RDT-8废水

采用HZ-16型大孔树脂对含三（三溴苯氧基）三嗪（RDT-8）废水进行吸附及脱附处理。实验结果表明：在废水流量为4.0 BV/h的条件下,树脂最佳吸附工艺条件为出水体积88.0 BV,此条件下出水COD小于291 mg/L,挥发酚质量浓度小于0.08 mg/L;在脱附液流量为0.5 BV/h的条件下,树脂最佳脱附工艺条件为脱附液体积3.0 BV,此条件下脱附液中挥发酚质量浓度为30.6 mg/L,挥发酚脱附率高达76.4%。在最佳吸附-脱附工艺条件下,连续进行10次动态吸附-脱附实验,吸附出水中COD为137~294 mg/L,COD去除率为72.5%~89.1%,挥发酚质量浓度稳定在0.05 mg/L以下,挥发酚去除率为99.8%~100%,说明HZ-16型大孔树脂的吸附-脱附性能稳定。     

树脂吸附—Fenton氧化法处理精对苯二甲酸废水

采用树脂吸附-Fenton加氧化法处理精对苯二甲酸（PTA）废水,考察了树脂吸附及Fenton氧化的最佳工艺条件。实验结果表明,采用NDA-88吸附树脂,在室温、吸附流速2BV／h条件下,每批次处理量为28BV,COD去除率为80％左右;采用Fenton试剂进一步氧化处理,在废水pH为3、质量分数30％的8202加入量为1．2％（体积分数）、H2O2与Fe^2＋摩尔比为3：1、反应温度为40℃、反应时间为4h条件下,出水COD为72mg／L,COD去除率为87％,可达到国家一级排放标准。     

树脂吸附法处理磺胺中间体生产废水的研究

研究了树脂吸附法处理磺胺中间体生产废水的工艺过程，研究结果表明，NDA－900吸附树脂对该废水具有良好的吸附－脱附处理效果，在原废水中对氨基苯磺酸质量浓度为5000－6000mg/L，氨基值近5000mg/L,COD高达10000mg/L以上，经树脂吸附处理后（处理量为每批次12BV），对氨基苯磺酸的去除率大于96％，氨基值去除率大于65％，COD去除率大于55％，树脂脱附液经酸化结晶，过滤处理，可回收对氨基苯磺酸。     

离子交换树脂处理三乙胺废水

采用离子交换树脂对废水中三乙胺进行吸附。探讨了静态及动态吸附三乙胺的影响因素,考察了树脂的脱附条件及其吸附稳定性。实验结果表明:RX01型树脂对三乙胺的吸附性能优于HD-81型和D155型树脂;在三乙胺初始质量浓度为1 500 mg/L、初始pH为11.5、吸附时间为2 h、吸附温度为298 K的静态吸附条件下,三乙胺去除率为96.3%,饱和吸附量为145 mg/g,等浓度条件下阳离子影响的大小顺序为Ca~(2+)Mg~(2+)K~(+)Na~(+);当三乙胺初始质量浓度为1 500 mg/L、废水流量为60 BV/h、动态吸附柱高径比为5.37时,穿透体积为70 BV,出水三乙胺质量浓度小于3 mg/L,三乙胺去除率高达99.5%;以2 mol/L的HCl溶液为脱附剂,脱附剂流量为1 BV/h、出水体积为4 BV时,三乙胺的脱附率达94.8%;在最优动态吸附-脱附条件下重复使用10次,树脂性能稳定。     

树脂吸附法去除水及空气中的CS2

采用XDA-1树脂吸附固定床工艺，对CS2饱和水溶液和含CS2的空气分别进行了动态吸附性能和影响因素的研究。在室温、CS2饱和水溶液流速为40BV／h（BV为树脂床体积）、中性或弱酸性的条件下，XDA—1树脂对水中饱和CS2的吸附效率达98．1％，对CS2的吸附量可达54．0g／L。在室温和气体流速为600BV／h的条件下，XDA-1树脂对空气中CS2的吸附效率为63．9％-90．0％，对CS2的吸附量可达28．0～36．8g／L。采用水蒸气解吸和冰水冷凝可以回收84．9％-90．0％的CS2。     

树脂吸附-Fenton试剂氧化法处理水杨醛生产废水

采用树脂吸附-Fenton试剂氧化法处理水杨醛生产废水。XF-01树脂和XF-02树脂静态吸附水杨醛生产废水时,COD去除率均在85％以上,挥发酚去除率均高于90％。XF-02树脂对水杨醛生产废水的处理效果更佳。动态吸附随废水流量增大,吸附出水的COD和挥发酚质量浓度均增加。适宜的废水流量为15BV,树脂的最佳脱附温度为80℃。在连续4批的吸附-脱附实验中,吸附出水的平均COD约为1200mg／L,平均挥发酚质量浓度小于10mg／L。在Fenton试剂氧化中,铁屑和铁粉的催化效果差别很小,都好于FeSO4·7H2O。以铁屑为催化剂、H2O2溶液加入量为1％时,氧化出水的COD小于150mg／L,挥发酚质量浓度小于0．5mg／L。     

苯基周位酸生产废水处理试验研究

采用CHA－111大孔吸附树脂对苯基周位酸生产过程排放的汽提苯胺盐析废水和苯基周位酸酸析母液进行处理试验,效果良好。汽提苯胺盐析废水苯胺质量浓度＞1600mg／L,经树脂吸附处理后苯胺质量浓度＜2mg／L,苯胺去除率＞99．9％,COD去除率＞97％,树脂工作吸附量达120g／L,脱附率＞98％;苯基周位酸酸析母液经树脂吸附、混凝沉淀处理后,苯基周位酸质量浓度＜190mg／L,苯基周位酸去除率为94．8％,COD去除率为94．3％,氨基值去除率为80％,脱附率＞99％。     

树脂吸附法处理硝基苯和硝基氯苯生产废水的研究

研究了用ＣＨＡ－１１１树脂吸附处理硝基本和硝基氯苯生产废水的最佳工艺条件，当废水中硝基苯类化合物含量为６３９ｍｇ／Ｌ时，ＣＨＡ－１１１树脂的工作吸附容量为１２６ｍｇ／ｍＬ，处理水量为１９０ＢＶ，处理后硝苯类化合物的浓度〈５ｍｇ／Ｌ，去除率〉９９％；采用异丙醇作脱附剂；表明该树脂的吸附与脱附性能良好。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.