Sorption of hazardous metals from single and multi-element solutions by saltbush biomass in batch and continuous mode: interference of calcium and magnesium in batch mode

Batch studies were performed to determine the interference of calcium (Ca) and magnesium (Mg) on the sorption of Cu(II), Cd(II), Cr(III), Cr(VI), Pb(II), and Zn(II) [from CuSO(4), K(2)Cr(2)O(7), Pb(NO(3))(2), Cr(NO(3))(3), ZnCl(2), and Cd(NO(3))(2)] by saltbush (Atriplex canescens) biomass. The results demonstrated that Ca and Mg at concentrations of at least 20 times higher than the concentration of most of the target metals did not interfere with the metal binding. The data show that the batch binding capacity from a multimetal solution at pH 5.0 was (micromol/g) about 260 for Cr(III) and Pb, and about 117, 54, and 49 for Cu, Zn, and Cd, respectively. The use of 0.1M HCl allowed the recovery of 85-100% of the bound Cu, Cr(III), and Pb, and more than 37% of the bound Cd and Zn. The column binding capacity for Pb was about 49 micromol/g from both the single and multimetal solutions, while it was, respectively about 35 and 23 micromol/g for Cr(III). The binding capacity for Cu and Zn from the single and multimetal column experiments was 35 micromol/g and less than 10 micromol/g, respectively. The stripping data from the single column experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and Zn, 90% and 74% of the bound Pb and Cr(VI), respectively, and less than 25% of the bound Cd and Cr(III), while the stripping from the multimetal experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and about 74%, 54%, 43%, and 40% of the bound Pb, Zn, Cd, and Cr(III), respectively.     

Attenuation of divalent toxic metal ions using natural sericitic pyrophyllite

The present study investigated the effectiveness of an inexpensive and ecofriendly alumino silicate clay mineral, sericitic pyrophyllite, as an adsorbent for the possible application in the removal of some divalent toxic metal cations such as Pb(2+), Cu(2+)and Zn(2+) from aqueous systems. Batch scale equilibrium adsorption studies were carried out for a wide range of initial concentration from 24.1 to 2410mumolL(-1) for lead, 78.65 to 7865mumolL(-1) for copper and 76.45 to 7645mumolL(-1) for zinc solutions. The removal of Pb(2+) was almost complete at low concentration (maximum lead removal capacity, LRC, 32mg of lead/g of pyrophyllite) with 10gL(-1) of adsorbent in a 30min equilibration time. The effects of temperature on adsorption of heavy metal ions were studied. The applicability of the Langmuir, Freundlich and Dubinin-Radushkevich adsorption models in each case of lead, copper and zinc adsorption was examined separately at different temperatures. The adsorption process was found to be endothermic and the Freundlich adsorption model was found to represent the data at different temperatures more suitably.     

Prediction of zinc, cadmium, lead, and copper availability to wheat in contaminated soils using chemical speciation, diffusive gradients in thin films, extraction, and isotopic dilution techniques

To predict the availability of metals to plants, it is important to understand both solution- and solid-phase processes in the soil, including the kinetics of metal release from its binding agent (ligand and/or particle). The present study examined the speciation and availability of Zn, Cd, Pb, and Cu in a range of well-equilibrated metal-contaminated soils from diverse sources using several techniques as a basis for predicting metal uptake by plants. Wheat (Triticum aestivum L.) was grown in 13 metal-contaminated soils and metal tissue concentrations (Zn, Cd, Pb, and Cu) in plant shoots were compared with total soil metal concentrations, total soluble metal, and free metal activities (pM2+) in soil pore waters, 0.01 M CaCl2-extractable metal concentrations, E values measured by isotope dilution, and effective metal concentrations, C(E), measured by diffusive gradients in thin films (DGT). In the DGT technique, ions are dynamically removed by their diffusion through a gel to a binding resin, while E values represent the isotopically exchangeable (labile) metal pools. Free metal activities (Zn2+, Cd2+, and Pb2+) in soil pore waters were determined using a Donnan dialysis technique. Plant Zn and Cd concentrations were highly related to C(E), while relationships for Zn and Cd with respect to the other measures of metals in the soils were generally lower, except for CaCl2-extractable Cd. These results suggest that the kinetically labile solid-phase pool of metal, which is included in the DGT measurement, played an important role in Zn and Cd uptake by wheat along with the labile metal in soil solution. Plant Pb concentrations were highly related to both soil pore water concentrations and C(E), indicating that supply from the solid phase may not be so important for Pb. Predictions of Cu uptake by wheat from these soils by the various measures of Cu were generally poor, except surprisingly for total Cu.     

Release dynamic process identification for a cement based material in various leaching conditions. Part I. Influence of leaching conditions on the release amount

In this paper we investigate at laboratory scale the influence of the liquid/solid leaching conditions on the release of different chemical species from a reference porous material obtained by solidification of PbO and CdO with Portland cement. The pH influence on the dissolution of pollutants and the initial pore solution composition (target elements: Na(+), K(+), Ca(2+), Pb(2+), Cd(2+), SO(4)(2-)) were assessed by applying a methodology consisting of two equilibrium leaching tests, the Acid Neutralization Capacity (ANC) and the Pore Water (PW) tests and geochemical modelling. Samples of the same material were submitted in parallel to four different dynamic leaching tests in order to determine the influence of the sample shape (monolithic or granular) and eluate hydrodynamics (instantaneous L/S ratio, eluate renewal) on the leaching of the target elements. The comparison criteria were the eluate saturation state, the cumulative release and the released flux. Generally, the eluates obtained in the tests applied on granular material were more concentrated, even saturated for the eluate pH value with respect to Ca(2+), Pb(2+) and SO(4)(2-). The consequence of the eluate saturation is the slowing down effect on the dynamic release. The highest released flux was observed for the Monolith Leaching Test (MLT) involving the highest instantaneous L/S ratio and the lowest solid/liquid exchange surface and for which no saturation was observed, except Pb(2+) and SO(4)(2-) in some eluates. The maximum cumulative released-mass was obtained for the Column Leaching Test (CLT) applied on granular material having the highest exchange surface, the lowest instantaneous L/S and a continuous input flow of the leachant. The experimental results demonstrate the significance of the liquid/solid contact type which is also a scenario specific parameter.     

Removal of perchlorate from contaminated waters using surfactant-modified zeolite

We investigated the potential of using surfactant (hexadecyltrimethylammonium)-modified zeolite (SMZ) as an inexpensive sorbent for removing perchlorate (ClO(4)(-)) from contaminated waters in the presence of competing anions. In batch systems, the presence of 10 mM OH(-) (i.e., pH 12), CO(3)(2-), Cl(-), or SO(4)(2-) had little effect on the sorption of ClO(4)(-) by SMZ, indicating that the sorption of ClO(4)(-) by SMZ was very selective. The presence of 10 mM NO(3)(-), however, reduced the sorption of ClO(4)(-) at low initial concentrations. The maximum sorption capacity for ClO(4)(-) by the SMZ remained relatively constant (40-47 mmol kg(-1)), in the absence or presence of the competing ions. In flow-through systems, ClO(4)(-) broke through the SMZ columns much later than other anions present in an artificial ground water. The affinity of the anions for SMZ followed the sequence of ClO(4)(-) > > NO(3)(-) > SO(4)(2-) > Cl(-). Perchlorate loading under dynamic flow-through conditions was 34 mmol kg(-1), somewhat less than the maximum loading of 40 to 47 mmol kg(-1) determined by the batch method. Less than 1% of previously sorbed ClO(4)(-) was leached out by ultra-pure water, by extraction fluid #1 of the standard toxicity characteristic leaching procedure (TCLP), or by a solution of 0.28 M Na(2)CO(3)/0.5 M NaOH. About 40% of the previously sorbed ClO(4)(-) was leached out from SMZ by a 0.5 M NO(3)(-) solution. The exchange of ClO(4)(-) with NO(3)(-) corroborated results of the batch tests where NO(3)(-) was shown to compete with ClO(4)(-) sorption.     

Nutrients and nonessential elements in soil after 11 years of wastewater irrigation

Irrigation of citrus (Citrus aurantium L. × Citrus paradise Macf.) with urban reclaimed wastewater (RWW) can be economical and conserve fresh water. However, concerns remain regarding its deleterious effects on soil quality. We investigated the ionic speciation (ISP) of RWW and potential impacts of 11 yr of irrigation with RWW on soil quality, compared with well-water (WW) irrigation. Most of nutrients (～53-99%) in RWW are free ionic species and readily available for plant uptake, such as: NH(4+), NO(3-), K(+), Ca(2+), Mg(2+), SO(4)(2-), H(3)BO(3), Cl(-), Fe(2+), Mn(2+), Zn(2+), Co(2+), and Ni(2+), whereas more than about 80% of Cu, Cr, Pb, and Al are complexed with CO(3-), OH(-), and/or organic matter. The RWW irrigation increased the availability and total concentrations of nutrients and nonessential elements, and soil salinity and sodicity by two to three times compared with WW-irrigated soils. Although RWW irrigation changed many soil parameters, no difference in citrus yield was observed. The risk of negative impacts from RWW irrigation on soil quality appears to be minimal because of: (i) adequate quality of RWW, according to USEPA limits; (ii) low concentrations of metals in soil after 11 yr of irrigation with RWW; and (iii) rapid leaching of salts in RWW-irrigated soil during the rainy season.     

The effect of Oja-titun market effluent on the chemical quality of receiving OPA reservoir in Ile-Ife, Nigeria

The effect of market effluent from the Oja-titun market in Ile-Ife, Nigeria on the chemical quality of the Opa Reservoir located 3.5 km downstream was investigated between February and November 2000. Water samples were collected in February, May, August and November from 16 sites, four along each of the market drainage channels (MDC), market stream, tributary stream and the Opa River and Reservoir. The peak level of each variable-biochemical oxygen demand, temperature, total alkalinity, Na(+), K(+), Ca(2+), Mg(2+), PO(4)(3+), SO(4)(2+), Cl(-), NO(3)(-), Pb and Zn-occurred at the MDC, and decreased significantly downstream, except pH, conductivity and dissolved oxygen, which increased. Seasonal fluctuation in most variables was pronounced. Generally, there were high values in the early dry and dry seasons and low values in the rainy and early rainy seasons. Comparison of the reservoir water with international limitation standards for drinking water supply showed that the quality of the reservoir water was very low and that treatment required to achieve minimum limitation standards for drinking water would be both intensive and expensive. The study concluded that the stream borne effluent from the market impacts significantly on the chemical quality of the reservoir water although other tributaries within the Reservoir's catchment are other possible sources of pollutants in the reservoir.     

Sorption of trace metals by standard and micro suction cups in the absence and presence of dissolved organic carbon

Both the bioavailability of a trace metal (TM) in a soil and the risk of leaching to the ground water are linked to the metals concentration in the soil solution. Sampling soil solution by tension lysimetry with suction cups is a simple and established technique that is increasingly used for monitoring dissolved TM in soils. Of major concern, however, is the sorption of TM by the walls of the samplers. Metal sorption by different materials used in suction cups can vary widely, depending also on the chemistry of the soil solution. We compared the sorption of Cu, Zn, Cd, and Pb by different standard-size and micro suction cups in the laboratory at two pH values (4.5 and 7.5 or 8.0) in absence and presence of dissolved organic carbon (DOC). In addition, we investigated the sorption of DOC from different origins by the cup materials. At both pH values, the weakest sorption of all four TMs was exhibited by standard-size suction cups based on nylon membranes and by hollow fibers made from polyvinyl alcohol (PVA). At alkaline pH, borosilicate glass, ceramic materials, and polytetrafluorethylene (PTFE) mixed with silicate were characterized by generally strong sorption of all investigated TMs. In addition, Cu and Pb were strongly sorbed at low pH by PTFE-silicate and a ceramic material used for the construction of standard-size suction cups. On the other hand, sorption of Cu, Zn, and Cd by ceramic capillaries produced from pure aluminum oxide was negligible at low pH. Micro suction cups made of an unknown polymerous tube sorbed Cu strongly, but were well suited to monitor Zn, Cd, and Pb at low pH, and, in the presence of DOC, also at high pH. Major cations (Na+, Mg2+, K+, Ca2+) and anions (Cl-, NO3-, SO4(2-)) were not or very weakly sorbed by all cup materials, except for Mg2+, K+, and Ca2+ by borosilicate glass at pH 7.5. Trace metal sorption by suction cups was generally greatly reduced in the presence of DOC, especially at alkaline pH. The sorption of DOC itself depended on its source. Dissolved organic carbon from leaf litter extracts with a probably large hydrophobic fraction was sorbed more strongly than mainly hydrophilic DOC from a mineral soil solution.     

Heavy metal release from contaminated soils: comparison of column leaching and batch extraction results

Heavy metals in soils may adversely affect environmental quality. In this study, we investigated the release of Zn, Cd, Pb, and Cu from four contaminated soils by column leaching and single and sequential batch extractions. Homogeneously packed soil columns were leached with 67 mL/g 10(-2) M CaCl2 to investigate the exchangeable metal pool and subsequently with 1400 mL/g 10(-2) M CaCl2 adjusted to pH 3 to study the potential of metal release in response to soil acidification. In two noncalcareous soils (pH 5.7 and 5.1), exchange by Ca resulted in pronounced release peaks for Zn and Cd that were coupled to the exchange of Mg by Ca, and 40 to 70% of total Zn and Cd contents were rapidly mobilized. These amounts compared well with exchangeable pools determined in single and sequential batch extractions. In two soils with near-neutral pH, the effluent concentrations of Zn and Cd were several orders of magnitude lower and no pronounced elution peaks were observed. This behavior was also observed for Cu and Pb in all four soils. When the soils were leached at pH 3, the column effluent patterns reflected the coupling of CaCO3 dissolution (if present) and other proton buffering reactions, proton-induced metal release, and metal-specific readsorption within the soil column. Varying the flow rate by a factor of five had only minor effects on the release patterns. Overall, Ca exchange and subsequent acidification to pH 3 removed between 65 and 90% of total Zn, Cd, Pb, and Cu from the four contaminated soils.     

The potential of cost-effective coconut husk for the removal of toxic metal ions for environmental protection

Coconut (Cocos nucifera) husk, an agricultural waste, has been thoroughly investigated for the removal of toxic Cd(II), Cr(III) and Hg(II) ions from aqueous media. The parameters like nature and composition of electrolyte, concentration of toxic ions, dosage of coconut husk, and equilibration time between the two phases were optimized for their maximum accumulation onto the solid surface. The effect of common ions on the uptake of metal ions has been monitored under optimal conditions. The variation of retention of each metal ion with temperature was used to compute the thermodynamic quantities DeltaH, DeltaS and DeltaG. The values 18.1+/-0.6 kJmol(-1), 74+/-2 Jmol(-1)K(-1), and -3.8+/-0.04 kJmol(-1) at 298 K; 10.8+/-0.8 kJmol(-1), 48.8+/-2.7 Jmol(-1)K(-1), and -4.6+/-0.3 kJmol(-1) at 298 K; and -37.4+/-2k Jmol(-1), 105+/-7 Jmol(-1)K(-1) and -2.58+/-0.5 kJmol(-1) at 298 K were obtained for Cd(II), Cr(III) and Hg(II) ions, respectively. The sorption data were analysed by applying different sorption isotherms. The sorption capacity and energy were evaluated for each metal ion. The values of the Freundlich constants 1/n and C(m) were 0.92+/-0.04 and 52.6+/-22.2 mmolg(-1); 0.85+/-0.05 and 56.0+/-0.03 mmolg(-1); and 0.88+/-0.03 and 6.84+/-0.45 mmolg(-1) for Cd(II) Cr(III) and Hg(II) ions, respectively. Similarly, the Dubinin-Radushkevich (D-R) constants beta, X(m,) and E were evaluated for the three metal ions. To check the selectivity of the sorbent, sorption of a number of elements was measured under similar conditions. Separation of Zn(II) from Cd(II); Cr(III) from I(I), Zr(IV), Se(IV), and Hg(II) from Se(IV) and Zn(II) can be achieved using this sorbent. This cheap material has potential applications in analytical chemistry, water decontamination, industrial effluent treatment and in pollution abatement.     

Influence of quaternary ammonium on sorption of selected metal cations onto clinoptilolite zeolite

Clay minerals and zeolites have large cation exchange capacities, which enable them to be modified by cationic surfactant to enhance their sorption of organic and anionic contaminants. In this study, the influence of quaternary ammonium surfactants on sorption of five metal cations (Cs+, Sr+, La3+, Pb2+, and Zn2+) onto a clinoptilolite zeolite was investigated. Generally, the metal cation sorption capacity and affinity for the zeolite decreased, indicating that presorbed cationic surfactants blocked sorption sites for metal cations, as the surfactant loading on the zeolite increased. Cesium and Pb2+ sorption was affected to a small extent, indicating that selective sorption for Cs+ and specific sorption for Pb2+ play an important role in addition to cation exchange. Sorption of cationic surfactants on zeolite preloaded with different metal cations showed a strong correlation with the chain length of the surfactant tail group, while the roles of the charges and types of the metal cations were minimal. As the chain length increases, the critical micelle concentration decreases and the surfactant molecules become more hydrophobic, resulting in progressive bilayer coverage. Desorption of presorbed metal cations by cationic surfactants was strongly affected by the surfactant chain length and metal type. More metal cations, particularly Sr2+ and Zn2+, desorbed with an increase in surfactant chain length. The results, in combination with those from organic and oxyanion sorption on surfactant-modified zeolite, may be used for future surfactant modification to target sorption and desorption of a specific type of contaminant or a mixture of different types of contaminants.     

Biosorption of Cu(II), Zn(II), Ni(II) and Pb(II) ions by cross-linked metal-imprinted chitosans with epichlorohydrin

Cross-linked metal-imprinted chitosan microparticles were prepared from chitosan, using four metals (Cu(II), Zn(II), Ni(II), and Pb(II)) as templates, and epichlorohydrin as the cross-linker. The microparticles were characterized by Fourier transform infrared spectroscopy, solid state (13)C nuclear magnetic resonance spectroscopy, and energy-dispersive X-ray spectroscopy. They were used for comparative biosorption of Cu(II), Zn(II), Ni(II) and Pb(II) ions in an aqueous solution. The results showed that the sorption capacities of Cu(II), Zn(II), Ni(II), and Pb(II) on the templated microparticles increased from 25 to 74%, 13 to 46%, 41 to 57%, and 12 to 43%, respectively, as compared to the microparticles without metal ion templates. The dynamic study showed that the sorption process followed the second-order kinetic equation. Three sorption models, Langmuir, Freundlich, and Dubinin-Radushkevich, were applied to the equilibrium isotherm data. The result showed that the Langmuir isotherm equation best fitted for monolayer sorption processes. Furthermore, the microparticles can be regenerated and reused for the metal removal.     

Biosorption of heavy metals by activated sludge and their desorption characteristics

The biosorption of different metals (Cu2+, Cd2+, Zn2+, Ni2+ and Pb2+) was investigated using activated sludge. The optimum pH was 4 for Cd, Cu and Pb sorption and 5 for Ni and Zn. Biomass metal uptake clearly competed with protons present in the aqueous medium, making pH an important variable in the process. Protons consumed by biomass in control tests versus protons exchange in biosorption tests confirmed a maximum exchange between metal cations and protons at pH 2. The study of the influence of biomass concentration revealed that the amount of protons released from biomass increased with biomass concentration. This would confirm the hypothesis of ion exchange between both types of ions. The application of the Langmuir and Freundlich models showed a better fitting of experimental data to the first model. The maximum sorption uptake of the studied metals by the activated sludge showed the following decreasing order: Pb>Cu>CdZn>Ni. Desorption experiments showed that HCl was a good eluent for the five metals tested, particularly at low pH values (1 and 2). At pH 3 or 4 the desorption yield was significantly lower. However, its use did not allow the reuse of biomass in subsequent loading and unloading cycles. EDTA was also a good desorption agent, achieving the total recovery for the five metals tested at a concentration of 1mM, with the advantage that biomass could be reused for three sorption-desorption cycles.     

Assessment of metal availability in smelter soil using earthworms and chemical extractions

Chemical immobilization is a relatively inexpensive in situ remediation method that reduces soil contaminant solubility, but the ability of this remediation treatment to reduce heavy metal bioavailability and ecotoxicity to soil invertebrates has not been evaluated. Our objectives were to (i) assess the ability of chemical immobilization amendments (municipal sewage sludge biosolids and rock phosphate) to reduce metal bioavailability and toxicity in a toxic metal-contaminated smelter soil and (ii) evaluate soil extraction methods using Ca(NO3)2 solution or ion-exchange membranes coated with diethylenetriaminepentaacetic acid (DTPA) as surrogate measures of metal bioavailability and ecotoxicity. We treated a soil contaminated by Zn and Pb milling and smelting operations and an uncontaminated control soil with lime-stabilized municipal biosolids (LSB), rock phosphate (RP), or anaerobically digested municipal biosolids (SS) and evaluated lethality of the remediated soils to earthworm (Eisenia fetida Savigny). Lime-stabilized municipal biosolids was the only remediation amendment to successfully immobilize lethal levels of Zn in the smelter soil (14-d cumulative mortality < or = 15%). Calcium nitrate-extractable Zn in the lethal Zn smelter soil-amendment combinations was 11.5 to 18.2 mmol/kg, compared with the nonlethal LSB amended soil (0.62 mmol/kg). The Ca(NO3)2-extractable Zn-based median lethal concentration (LC50) of 6.33 mmol/kg previously developed in Zn-spiked artificial soils was applicable in the remediated smelter soils despite a 14-fold difference in total Zn concentration. Chelating ion-exchange membrane uptake among the soils was highly variable (mean CV = 39%) compared with the Ca(NO3)2-extraction (mean CV = 1.9%) and not well related to earthworm toxicity.     

Use of diammonium phosphate to reduce heavy metal solubility and transport in smelter-contaminated soil

Phosphate treatments can reduce metal dissolution and transport from contaminated soils. However, diammonium phosphate (DAP) has not been extensively tested as a chemical immobilization treatment. This study was conducted to evaluate DAP as a chemical immobilization treatment and to investigate potential solids controlling metal solubility in DAP-amended soils. Soil contaminated with Cd, Pb, Zn, and As was collected from a former smelter site. The DAP treatments of 460, 920, and 2300 mg P kg-1 and an untreated check were evaluated using solute transport experiments. Increasing DAP decreased total metal transported. Application of 2300 mg P kg-1 was the most effective for immobilizing Cd, Pb, and Zn eluted from the contaminated soil. Metal elution curves fitted with a transport model showed that DAP treatment increased retardation (R) 2-fold for Cd, 6-fold for Zn, and 3.5-fold for Pb. Distribution coefficients (Kd) increased with P application from 4.0 to 9.0 L kg-1 for Cd, from 2.9 to 10.8 L kg-1 for Pb, and from 2.5 to 17.1 L kg-1 for Zn. Increased Kd values with additional DAP treatment indicated reduced partitioning of sorbed and/or precipitated metal released to mobile metal phases and a concomitant decrease in the concentration of mobile heavy metal species. Activity-ratio diagrams indicated that DAP decreased solution Cd, Pb, and Zn by forming metal-phosphate precipitates with low solubility products. These results suggest that DAP may have potential for protecting water resources from heavy metal contamination near smelting and mining sites.     

Apatite and phillipsite as sequestering agents for metals and radionuclides

Laboratory and greenhouse studies were conducted to quantify apatite and phillipsite (zeolite) sequestration of selected metal contaminants. The laboratory batch study measured the sorption of aqueous Co2+, Ba2+, Pb2+, Eu3+, and UO2(2+). Apatite sorbed more Co2+, Pb2+, Eu3+, and UO2(2+) from the spike solution than phillipsite, resulting in distribution coefficients (Kd values) of >200,000 L kg(-1). Phillipsite was more effective than apatite at sorbing aqueous Ba2+. Results from the laboratory study were used to design the greenhouse study that used a soil affected by a Zn-Pb smelter from Pribram, Czech Republic. Two application rates (25 and 50 g kg(-1)) of phillipsite and apatite and two plant species, maize (Zea mays L.) and oat (Avena sativa L.), were evaluated in this study. There was little (maize) to no (oat) plant growth in the unamended contaminated soil. Apatite and, to a slightly lesser extent, phillipsite additions significantly enhanced plant growth and reduced Cd, Pb, and Zn concentrations in all analyzed tissues (grain, leaves, and roots). The sequestering agents also affected some essential elements (Ca, Fe, and Mg). Phillipsite reduced Fe and apatite reduced P and Fe concentrations in oat tissues; however, the level of these elements in oat leaves and grains remained sufficient. Sequential extractions of the soil indicated that the Cd, Pb, and Zn were much more strongly sorbed onto the amended soil, making the contaminants less phytoavailable.     

Cation-pi bonding: a new perspective on the sorption of polycyclic aromatic hydrocarbons to mineral surfaces

Recent molecular modeling and spectroscopic studies have suggested that relatively strong interactions can occur between aromatic pi donors and metal cations in aqueous solutions. The objective of this study was to characterize potential cation-pi interactions between pi donors and exchangeable cations accumulated at mineral surfaces via both spectroscopic and batch sorption methods. Quadrupolar splitting in deuterium nuclear magnetic resonance ((2)H NMR) spectroscopy for d(2)-dichloromethane, d(6)-benzene, and d(8)-toluene (C(6)D(5)- moiety) in aqueous suspensions of a Na-saturated reference montmorillonite unambiguously indicated the ordering of solute molecules with respect to the clay surface. The half line broadening (Delta nu(1/2)) of (2)H NMR of d(6)-benzene in montmorillonite suspensions showed that soft exchangeable cations generally resulted in more benzene sorption compared with harder cations (e.g., Ag(+) > Cs(+) > Na(+) > Mg(2+), Ba(2+)). In batch sorption experiments, saturating minerals (e.g., porous silica gels, kaolinite, vermiculite, montmorillonite) with a soft transition metal or softer base cations generally increased the polycyclic aromatic hydrocarbon (PAH) sorption relative to harder cations (e.g., Ag(+) > Cs(+) > K(+) > Na(+); Ba(2+) > Mg(2+)). Sorption of phenanthrene to Ag(+)-saturated montmorillonite was much stronger compared with 1,2,4,5-tetrachlorobenzene, a coplanar non-pi donor having slightly higher hydrophobicity. In addition, a strong positive correlation was found between the cation-dependent sorption and surface charge density of the minerals (e.g., vermiculite, montmorillonite > silica gels, kaolinite). These results, coupled with the observations in (2)H NMR experiments with montmorillonite, strongly suggest that cation-pi bonding forms between PAHs and exchangeable cations at mineral surfaces and affects PAH sorption to hydrated mineral surfaces.     

Concentration, pH, and surface charge effects on cadmium and lead sorption in three tropical soils

Reactions of heavy metals with soil are important in determining metal fates in the environment. Sorption characteristics of two heavy metals, Cd and Pb, in three tropical soils (Mollisol, Oxisol, and Ultisol) from Puerto Rico were assessed at varying metal concentrations (0 to 1.2 mM) and pH values (approximately 2 to 7). All soils sorbed more Pb than Cd. Sorption maxima were obtained for each metal for the Oxisol and Ultisol soils, but not the Mollisol. Sorption appeared to depend more on soil mineralogy than organic matter content. Sorption isotherms were linear within the sorption envelope with similar slopes for each soil-metal curve, when plotting metal sorption as a function of pH. Cadmium and Pb isotherms yielded average slopes of approximately 36+/-1 and 28+/-1 units (percent increase in metal sorption per 1-unit increase in pH), respectively. Metal sorption depended more on metal type than soil composition. Cadmium sorption displayed a greater pH dependence than Pb. Cadmium sorption was less than or equal to the amount of negative surface charge except at pH values greater than the point of zero net charge (PZNC). This suggests that Cd was probably sorbed via electrostatic surface reactions and/or possible inner-sphere complexation at pH > 3.7. However, the amount of Pb sorbed by the Oxisol was greater than the amount of negative surface charge, suggesting that Pb participates in inner-sphere surface reactions. Lead was sorbed more strongly than Cd in our soils and poses less of a threat to underlying ground water systems due to its lower mobility and availability.     

Heavy metal distribution and chemical speciation in tailings and soils around a Pb-Zn mine in Spain

Soil pollution by lead, zinc, cadmium and copper was characterized in the mine tailings and surrounding soils (arable and pasture lands) of an old Spanish Pb-Zn mine. Sixty soil samples were analyzed, determining the total metal concentration by acid digestion and the chemical fractionation of Pb and Zn by the modified BCR sequential extraction method. Samples belonging to mine waste areas showed the highest values, with mean concentrations of 28,453.50 mg kg(-1) for Pb, 7000.44 mg kg(-1) for Zn, 20.57 mg kg(-1) for Cd and 308.48 mg kg(-1) for Cu. High concentrations of Pb, Zn and Cd were found in many of the samples taken from surrounding arable and pasture lands, indicating a certain extent of spreading of heavy metal pollution. Acidic drainage and wind transport of dust were proposed as the main effects causing the dispersion of pollution. Sequential extraction showed that most of the Pb was associated with non-residual fractions, mainly in reducible form, in all the collected samples. Zn appeared mainly associated with the acid-extractable form in mine tailing samples, while the residual form was the predominant one in samples belonging to surrounding areas. Comparison of our results with several criteria reported in the literature for risk assessment in soils polluted by heavy metals showed the need to treat the mine tailings dumped in the mine area.