WATER QUALITY ANALYSIS OF THE HALIFAX RIVER,FLORIDA1

ABSTRACT: An application of the receiving water block of the EPA Storm Water management Model (SWMM) is presented to quantify water quality impacts and evaluated control alternatives for a 208 areawide waste water management plan in Volusia Country, Florida. The water quality impact analyses were conducted for dry-and wet-weather conditions to simulate dissolved oxygen (DO), chlorides, total nitrogen (TN), and total phosphorus (TP) in the Halifax Rivers, Florida, a 40-kilometer-long tidal estuary located on the Atlantic coast of Florida near Daytona Beach. Dry-weather analysis was performed using conventional 7-day, 10-year low flow conditions to determine a set of unit transfer coefficients which estimate the pollutant concentration transferred to any point in the estuary from a constant unit discharge of pollutants at the existing waste water treatment plant outfall locations. Wet-weather analysis was performed by continuous simulation of a typical three-month summer wet season in Florida. Three-month cumulative duration curves of DO, TN and TP concentrations were constructed to estimate the relative value of controlling urban runoff of waste water treatment plant effluent on the Halifax River. The three-month continuous simulation indicated that the greatest change in DO, TN, and TP duration curves is possible by abatement of waste water treatment plant pollution.     

INTEGRATING GEOGRAPHIC INFORMATION SYSTEMS IN GROUND-WATER APPLICATIONS USING NUMERICAL MODELING TECHNIQUES1

ABSTRACT: The Sand and Gravel Aquifer is the sole source of potable water in Escambia County, Florida. In order to better understand the hydraulics of the aquifer, a numerical computer model of the aquifer was developed. The model applied a finite element technique which allowed for density-dependent transport and flow in three dimensions. The modeling technique was integrated with GIS to develop a system for optimal management of the resource. The GIS was the primary tool in the development of the model grid, as well as being the integral component in the modeling procedure. Multiple model grids were developed for simulating regional flow and local flow/transport phenomena. The model grids were generated by the GIS where nodal and element sequencing were recorded. The grid topology was stored in the GIS with the element numbers, node numbers, and the related hydrogeologic attributes. The Triangulated Irregular Network (TIN) module was used for transferring interpolated value between GIS coverages. TIN allowed a fit of the model grid to the physical dimensions of the aquifer and for interpolating boundary values for telescopically refined grids. Calculations between TIN surfaces provided the residuals of the dependent variable from observed TIN surfaces. Model calibration was conducted within the GIS environment through a combination of visual and relational querying. The GIS provided an integrated environment which facilitated model analyses and data storage and retrieval.     

FIELD SCALE MULTIOBJECTIVE DECISION MAKING: A CASE STUDY FROM WESTERN IOWA1

ABSTRACT: Water quality issues in agriculture are growing in importance. A common theme is the provision of better information to decision makers. This study reports the trial of a prototype decision support system by the U.S. Department of Agriculture Natural Resources Conservation Service and the Agricultural Research Service in the NRCS Harrison County Field Office in 1998. Observed data collected at the Deep Loess Research Station (DLRS) near Treynor, Iowa, were extrapolated using a modified GLEAMS field scale simulation model that included a nitrogen leaching component and a crop growth component. An accounting tool was used to convert crop yield estimates into crop budgets. A model interface was built to specify the climate, soil, and topography of the field, as well as the management scenarios for the alternative management systems. For the Deep Loess Hills area of Harrison County, a total of six soil and slope groups, with 66 total combinations of management practices forming management systems, were defined and simulated based on previously calibrated data from DLRS. A multi‐objective decision support system, the Water Quality Decision Support System, or WQDSS, was used to examine the tradeoffs in a comprehensive set of variables affected by alternative management systems with farmers in Harrison County. The study concluded that a multiobjective decision support system should be developed to support conservation planning by the NRCS. Currently, a larger scale effort to improve water quality decision making is underway.     

SENSITIVITY OF GROUNDWATER FLOW MODELS TO VERTICAL VARIABILITY OF AQUIFER CONSTANTS1

ABSTRACT: The Ogallala aquifer in the Oklahoma Panhandle is in need of better management because of increased groundwater demand which has caused declines in static water levels at an alarming rate. A groundwater management computer model was developed for the Ogallala aquifer in the Texas Panhandle and treats the aquifer as a homogeneous system. In this study, the computer model has been modified in order to evaluate the effects of vertical layering on semi-static water level changes which occur during the dewatering of a single unconfined aquifer. The modified model was applied to a study area near Guymon, Oklahoma, using both the homogeneous and the multilayered cases. The aquifer is characterized by a saturated thickness of 400 feet. The accumulated drawdown values of the homogeneous and the multilayered cases demonstrate that an average difference of approximately 22% of the original saturated thickness occurs between the two cases before the base of the aquifer is encountered. Approximately 25% more time is required to dewater the layered aquifer. Thus, vertical variations of lithology in an aquifer such as the Ogallala should be considered when prediction is made relative to groundwater management.     

SIMULATION OF INTEGRATED SURFACE WATER AND GROUND WATER SYSTEMS - MODEL FORMULATION1

ABSTRACT: The unique characteristics of the hydrogeologic system of south Florida (flat topography, sandy soils, high water table, and highly developed canal system) cause significant interactions between ground water and surface water systems. Interaction processes involve infiltration, evapotranspiration (ET), runoff, and exchange of flow (seepage) between streams and aquifers. These interaction processes cannot be accurately simulated by either a surface water model or a ground water model alone because surface water models generally oversimplify ground water movement and ground water models generally oversimplify surface water movement. Estimates of the many components of flow between surface water and ground water (such as recharge and ET) made by the two types of models are often inconsistent. The inconsistencies are the result of differences in the calibration components and the model structures, and can affect the confidence level of the model application. In order to improve model results, a framework for developing a model which integrates a surface water model and a ground water model is presented. Dade County, Florida, is used as an example in developing the concepts of the integrated model. The conceptual model is based on the need to evaluate water supply management options involving the conjunctive use of surface water and groundwater, as well as the evaluation of the impacts of proposed wellfields. The mathematical structure of the integrated model is based on the South Florida Water Management Model (SFWMM) (MacVicar et al., 1984) and A Modular Three-Dimensional Finite-Difference Groundwater Flow Model (MODFLOW) (McDonald and Harbaugh, 1988).     

A CATALYST FOR REGIONALIZATION OF RURAL WATER SYSTEMS1

ABSTRACT: The National Regulatory Research Institute has recommended the merger of small rural water districts in the United States. Success at bringing about merger of these districts, which contain fewer than 3,500 customers, has been highly limited. The subject of this paper is a demonstration project that may act as a catalyst to achieve the desired goal of regionalization. A computerized hydraulic data management program (CHDMP) was developed for a case study in Nelson County, Kentucky. University professors, graduate students, and two water utilities’ staffs cooperated in network analysis employing computer hardware and software. The utilities’ staffs were taught the science and technology of hydraulic model preparation, simulation, and analysis for the case study distribution systems. As an integrated system, the model contained 294 pipes, 234 nodes, six pumps, and 11 tanks. Each utility's problem areas were identified and some of the individual and mutual benefits of hydraulic planning were illustrated. A dialogue resulted between the managers. Each manager described his goals and agreed that, although political merger was not feasible at the present time, future economic factors could be a definite influence in reversing that decision.     

COMBINED SURFACE WATER-GROUNDWATER ANALYSIS OF HYDROLOGICAL SYSTEMS WITH THE AID OF THE HYBRID COMPUTER1

The solution with the aid of the hybrid computer of the partial and total differential equations for an integrated surface water groundwater system is described. A versatile computing technique has been developed to make a rapid and accurate study of the groundwater response due to varying inputs (deep percolation) or outputs (evapotranspiration) from the groundwater system. Spatial variations in basic vegetation phenomena, such as pattern, and hydrological parameters, are represented by means of a grid network which also allows the input of variable boundary conditions. The model is applied to an area in Columbia, South America which is subject to high water-table conditions. Various reclamation schemes and management practices under conditions of irrigated agriculture are assessed.     

SUPPLEMENTAL IRRIGATION OF HORTICULTURAL CROPS IN THE HUMID REGION1

ABSTRACT: A computer model was developed in order to establish a yield predictive relationship and to estimate the water requirements for supplemental irrigation of horticultural crops in the humid region. Alternative distribution systems were developed and designed using the results from the computer model and Wood's (1980) pipe network algorithm. The capital, operational, and maintenance costs of the distribution and recommended on-farm irrigation systems were determined and used to evaluate the economic feasibility of the alternative designs. Results show that the concentration of irrigated area along the distribution system, the length of the distribution system, and cropping system all have an important effect on the economic feasibility of supplemental irrigation in Wayne County, Kentucky.     

REAL-TIME SOIL WATER MONITORING FOR OPTIMUM WATER MANAGEMENT1

Abstract: Efficient water resource management is one of the most important policy issues facing agriculture in Hawaii in the years ahead. Soil water sensors, multisensor capacitance probes (MCP), have been successfully used for different water management projects. These MCPs monitor water content at multiple depths and at various locations in real-time. The objectives of this study were to determine the effect of water content on field soil bulk density of Wahiawa silty clay tropical soil; measure field saturated hydraulic conductivity of this tropical soil: calibrate MCP system for this soil: and monitor and evaluate real-time soil water content variations under a tomato crop using the calibrated MCP system. Sensor calibration was conducted under laboratory conditions. Soil bulk density at different water contents and saturated hydraulic conductivity were measured on the field. Bulk density increased with increasing water content: there was a 30 percent bulk density increase as a result of 0.25 cm³ cm^-3 water content variation. Compared with the manufacturer's calibration, site specific laboratory calibration of MCP gave a more accurate determination of soil water. Field determined saturated hydraulic conductivity was higher than laboratory determined values reported in the literature for the same soil type. Real-time soil water content monitoring within the root zone showed substantial variations due to water input (irrigation and rainfall) and water output (evapotranspiration and deep percolations). However, water content variations were much further reduced in the soil layer below the root zone.     

RECYCLING INPUT DATA DURING ANALYTIC ELEMENT MODELING NEAR INDIANAPOLIS,INDIANA1

ABSTRACT: Overlapping and adjacent ground water investigations are common in areas where aquifers are threatened by industrial development. In the Indianapolis area in Marion County, Indiana, a patchwork of ground water flow models have been used during the past 20 years to evaluate ground water resources and to determine the effects of local contamination. In every case these ground water models were constructed from scratch. Site specific finite difference grids or finite element meshes inhibit the direct reuse of input data when the area of interest shifts. Because the aquifer is not discretized into a grid or mesh with analytic element models, there are unique opportunities for direct reuse of model input data. In two applications of this principle we illustrate how the newly emerging analytic element method allows a fairly straightforward reuse of model input data from previous models in the same general area. In analytic element models of Central Indiana, streams and their tributaries are represented in different resolutions. Input data items of several modeling studies are stored and cataloged on disk in such a manner that they can be selectively retrieved by a data management program PREPRO. In this manner, a new ground water model can be set up quickly with input data which have been previously defined and tested during model calibration.     

A HYDRODYNAMIC MODELING STUDY TO DETERMINE THE OPTIMUM WATER INTAKE LOCATION IN LAKE PALDANG,KOREA1

A three‐dimensional hydrodynamic model was applied to Lake Paldang, South Korea. The lake has three inflows, of which Kyoungan Stream has the smallest flow rate and poorest water quality. Since all drinking water intake stations are located near the confluence of Kyoungan Stream within the lake, this contaminated tributary may have a significant impact on the quality of drinking water sources. The optimum drinking water intake location was determined from the applied model. The model was calibrated and verified using the data measured under different hydrological conditions. The model results were in reasonable agreement with the field measurements in both calibration and verification. The circulation and spreading patterns of the incoming flows in the lake, as well as their composition ratios to the drinking water intakes were determined from the model, and three alternative intake locations were proposed. The simulation results suggested that the horizontal and vertical relocations of the intake aqueduct could significantly decrease the composition ratio of the contaminated water. From this study, it was concluded that the three‐dimensional hydrodynamic model could successfully simulate the temporal and spatial mixing patterns of incoming flows and become a useful tool in determining the optimum water intake location in Lake Paldang.     

OPTIMAL GROUND WATER MANAGEMENT IN TWO-AQUIFER SYSTEMS1

ABSTRACT; This paper presents a numerical model for the prediction of optimal ground water withdrawal from a two-aquifer system by observing a set of constraints determined by the ecological conditions of the ground water basin. The aquifer system consists of an upper unconfined and a lower confined aquifer with a leaky stratum between them. It is assumed that water is withdrawn from the confined aquifer only, but the unconfined aquifer will also be affected due to the leakiness of the layer separating the upper and lower aquifers. Simulation and linear programming are employed for developing a computer model for the optimal management of such systems, with the objectives of determining withdrawal rates for predetermined ground water levels.     

A life cycle based multi-objective optimization model for the management of computer waste

The accelerating pace of waste generation from used electrical and electronic equipment is of growing global concern. Within this waste stream, computer hardware is quite significant in terms of both volume and risk to the environment because of the hazardous materials within it. The waste management hierarchy of prevention, reuse, recycle, treatment and disposal in landfill is accepted as a universal guideline for waste management. The contemporary concept of integrated solid waste management is very complex comprising of not only the environmental aspects or the technical aspects of the waste management hierarchy, but also incorporating economic, institutional, perceived risk and social issues in the context of complete life cycle of waste. Moreover, when to shift from one stage of hierarchy to another, is an involved decision warranting inclusion of several case specific issues. This paper presents a life cycle based multi-objective model that can help decision makers in integrated waste management. The proposed model has been applied to a case study of computer waste scenario in Delhi, India, which apart from having computer waste from its native population receives large quantities of imported second hand computers. The model has been used to evaluate management cost and reuse time span or life cycle of various streams of computer waste for different objectives of economy, perceived risk and environmental impact. The model results for different scenarios of waste generation have been analyzed to understand the tradeoffs between cost, perceived risk and environmental impact. The optimum life cycle of a computer desktop was observed to be shorter by 25% while optimizing cost than while optimizing impact to the environment or risk perceived by public. Proposed integrated approach can be useful for determining the optimum life cycle of computer waste, as well as optimum configuration of waste management facilities, for urban centers where computer waste related issues are of growing concern.     

Modeling Hydrology in a Small Rocky Mountain Watershed Serving Large Urban Populations1

Abstract: This article describes the development of a calibrated hydrologic model for the Blue River watershed (867 km²) in Summit County, Colorado. This watershed provides drinking water to over a third of Colorado’s population. However, more research on model calibration and development for small mountain watersheds is needed. This work required integration of subsurface and surface hydrology using GIS data, and included aspects unique to mountain watersheds such as snow hydrology, high ground‐water gradients, and large differences in climate between the headwaters and outlet. Given the importance of this particular watershed as a major urban drinking‐water source, the rapid development occurring in small mountain watersheds, and the importance of Rocky Mountain water in the arid and semiarid West, it is useful to describe calibrated watershed modeling efforts in this watershed. The model used was Soil and Water Assessment Tool (SWAT). An accurate model of the hydrologic cycle required incorporation of mountain hydrology‐specific processes. Snowmelt and snow formation parameters, as well as several ground‐water parameters, were the most important calibration factors. Comparison of simulated and observed streamflow hydrographs at two U.S. Geological Survey gaging stations resulted in good fits to average monthly values (0.71 Nash‐Sutcliffe coefficient). With this capability, future assessments of point‐source and nonpoint‐source pollutant transport are possible.     

湖泊蓝藻水华数字化预警系统构建探讨

构造湖泊蓝藻水华数字化预警系统是我国湖泊水环境管理的一个重要方向。本文探讨了构建湖泊蓝藻水华数字化预警系统的若干技术问题,包括：（1）数字化预警数学模式。提出需重视流域尺度的氮磷营养物和沉积动态输入以及营养物、沉积物对水生态结构动力过程的影响,建立非点源模型和湖泊生态结构动力学模型相耦合的预警数学模型模式;在此基础上提出了各种数学模型的可借鉴模式。（2）湖泊蓝藻水华预警监测技术。总结了常规水质监测的数据筛选方法,探讨了遥感技术和实时传输监测技术在水质监测中的应用模式,提出了实时监测和遥感监测需解决的技术难题和实现方法。（3）湖泊蓝藻数字化预警系统的设计。提出了数学模型系统、水质监控系统的网络化集成设计模式,提出了基于网络化地理信息系统的计算机应用软件实现模式。     

A life cycle based multi-objective optimization model for the management of computer waste

The accelerating pace of waste generation from used electrical and electronic equipment is of growing global concern. Within this waste stream, computer hardware is quite significant in terms of both volume and risk to the environment because of the hazardous materials within it. The waste management hierarchy of prevention, reuse, recycle, treatment and disposal in landfill is accepted as a universal guideline for waste management. The contemporary concept of integrated solid waste management is very complex comprising of not only the environmental aspects or the technical aspects of the waste management hierarchy, but also incorporating economic, institutional, perceived risk and social issues in the context of complete life cycle of waste. Moreover, when to shift from one stage of hierarchy to another, is an involved decision warranting inclusion of several case specific issues. This paper presents a life cycle based multi-objective model that can help decision makers in integrated waste management. The proposed model has been applied to a case study of computer waste scenario in Delhi, India, which apart from having computer waste from its native population receives large quantities of imported second hand computers. The model has been used to evaluate management cost and reuse time span or life cycle of various streams of computer waste for different objectives of economy, perceived risk and environmental impact. The model results for different scenarios of waste generation have been analyzed to understand the tradeoffs between cost, perceived risk and environmental impact. The optimum life cycle of a computer desktop was observed to be shorter by 25% while optimizing cost than while optimizing impact to the environment or risk perceived by public. Proposed integrated approach can be useful for determining the optimum life cycle of computer waste, as well as optimum configuration of waste management facilities, for urban centers where computer waste related issues are of growing concern.     

A SELF-VERIFYING HYBRID COMPUTER MODEL OF RIVER-BASIN HYDROLOGY1

ABSTRACT. As demands upon available water supplies increase, there is an accompanying increase in the need to assess the downstream consequences resulting from changes at specific locations within a hydrologic system. The problem is approached in this study by hybrid computer simulation of the hydrologic system. Modeling concepts are based upon the development of basic relationships which describe the various hydrologic processes. Within a system these relationships are linked by the continuity-of-mass principle. Spatial resolution is achieved by considering the modeled areas as a series of subbasins. The time increment adopted for the model is one month, so that time varying quantities are expressed in terms of mean monthly values. The model is general in nature and is applied to a particular hydrologic system through a programmed verification procedure whereby model coefficients are evaluated for the particular system. In this study the model is applied to the Bear River basin of western Wyoming, southern Idaho, and northern Utah. Comparisons between observed and computed outflow hydrographs show good agreement. The utility of the model is demonstrated by predicting the effects of various possible water resource management alternatives. The verified hybrid computer program can be digitized for application to the digital computer.     

A Retrospective Look at the Water Resource Management Policies in Nassau County,Long Island,New York1

Abstract: The residents of Nassau County Long Island, New York receive all of their potable drinking water from the Upper Glacial, Jameco/Magothy (Magothy), North Shore, and Lloyd aquifers. As the population of Nassau County grew from 1930 to 1970, the demand on the ground‐water resources also grew. However, no one was looking at the potential impact of withdrawing up to 180 mgd (7.9 m³/s) by over 50 independent water purveyors. Some coastal community wells on the north and south shores of Nassau County were being impacted by saltwater intrusion. The New York State Legislature formed a commission to look into the water resources in 1972. The commission projected extensive population growth and a corresponding increase in pumping resulting in a projected 93.5 to 123 mgd (4.1 to 5.5 m³/s) deficit by 2000. In 1986, the New York Legislature passed legislation to strengthen the well permit program and also establish a moratorium on new withdrawals from the Lloyd aquifer to protect the coastal community’s only remaining supply of drinking water. Over 30 years has passed since the New York Legislature made these population and pumping projections and it is time to take a look at the accuracy of the projections that led to the moratorium. United States Census data shows that the population of Nassau County did not increase but decreased from 1970 to 2000. Records show that pumping in Nassau County was relatively stable fluctuating between 170 and 200 mgd (7.5 to 8.8 m³/s) from 1970 to 2004, well below the projection of 242 to 321 mgd (10.6 to 14.1 m³/s). Therefore, the population and water demand never grew to projected values and the projected threat to the coastal communities has diminished. With a stable population and water demand, its time to take a fresh look at proactive ground‐water resource management in Nassau County. One example of proactive ground‐water management that is being considered in New Jersey where conditions are similar uses a ground‐water flow model to balance ground water withdrawals, an interconnection model to match supply with demand using available interconnections, and a hydraulic model to balance flow in water mains. New Jersey also conducted an interconnection study to look into how systems with excess capacity could be used to balance withdrawals in stressed aquifer areas with withdrawals in unstressed areas. Using these proactive ground‐water management tools, ground‐water extraction could be balanced across Nassau County to mitigate potential impacts from saltwater intrusion and provide most water purveyors with a redundant supply that could be used during water emergencies.     

INTEGRATING GEOGRAPHIC INFORMATION SYSTEMS AND MODFLOW FOR GROUND WATER RESOURCE ASSESSMENTS1

ABSTRACT: The Floridan Aquifer is the primary source of water in the coastal area of Santa Rosa County, Florida. In order to optimize well field design and analyze aquifer stress problems, the USGS MODFLOW code (McDonald and Harbaugh, 1988) is applied to develop a numerical computer model of the aquifer. The Geographical Information System (GIS) is the primary tool used in the development of the model grid, performance of the modeling procedure, and model analysis. The GIS is used in generating multiple grids in which to simulate both regional scale and local scale flow. The grid topology is recorded in geographic coordinates which facilitates geo-referencing and orientation of the grid to base maps and data coyerages. The GIS allows data transfer from various coverages to the nodes of the block centered grid where hydrogeologic information is stored as attributes to the grid coverage. From this grid coverage, pertinent information is queried within the GIS environment and used to generate the input files for the MODFLOW simulation. After MODFLOW execution, simulated heads and drawdown are imported into the grid coverage where residual error and recharge rates can be calculated. Contoured surfaces are then created for selected data sets including simulated heads, drawdown, residual error, and recharge rates. Model calibration is conducted utilizing the GIS to generate and process data sets associated with model simulations.