Potential carbon sequestration in China’s forests

Forests are believed to be a major sink for atmospheric carbon dioxide. There are 158.94 million hectares (Mha) of forests in China, accounting for 16.5% of its land area. These extensive forests may play a vital role in the global carbon (C) cycle as well as making a large contribution to the country’s economic and environmental well-being. Currently there is a trend towards increased development in the forests. Hence, accounting for the role and potential of the forests in the global carbon budget is very important.In this paper, we attempt to estimate the carbon emissions and sequestration by Chinese forests in 1990 and make projections for the following 60 years based on three scenarios, i.e. “baseline”, “trend” and “planning”. A computer model F-CARBON 1.0, which takes into account the different biomass density and growth rates for the forests in different age classes, the life time for biomass oxidation and decomposition, and the change in soil carbon between harvesting and reforestation, was developed by the authors and used to make the calculations and projections. Climate change is not modelled in this exercise.We calculate that forests in China annually accumulate 118.1 Mt C in growth of trees and 18.4 Mt in forest soils, and release 38.9 Mt, resulting in a net sequestration of 97.6 Mt C, corresponding to 16.8% of the national CO₂ emissions in 1990. From 1990 to 2050, soil carbon accumulation was projected to increase slightly while carbon emissions increases by 73, 77 and 84%, and net carbon sequestration increases by −21, 52 and 90% for baseline, trend and planning scenarios, respectively. Carbon sequestration by China’s forests under the planning scenario in 2000, 2010, 2030 and 2050 is approximately 20, 48, 111 and 142% higher than projected by the baseline scenario, and 8, 18, 34 and 26% higher than by the trend scenario, respectively. Over 9 Gt C is projected to accumulate in China’s forests from 1990 to 2050 under the planning scenario, and this is 73 and 23% larger than projected for the baseline and trend scenarios, respectively. During the period 2008–2012, Chinese forests are likely to have a net uptake of 667, 565 and 452 Mt C, respectively, for the planning, trend and baseline scenarios. We conclude that China’s forests have a large potential for carbon sequestration through forest development. Sensitivity analysis showed that the biggest uncertainty in the projection by the F-CARBON model came from the release coefficient of soil carbon between periods after harvesting and before reforestation.     

Cost estimates of the Kigali Amendment to phase-down hydrofluorocarbons

Hydrofluorocarbons (HFCs) are synthetically produced compounds primarily used for cooling purposes and with strong global warming properties. In this paper, we analyze the global abatement costs for achieving the substantial reductions in HFC consumption agreed in the Kigali Amendment (KA) of the Montreal Protocol from October 2016. We estimate that compliance with the KA is expected to remove 39 Pg CO₂eq or 61% of global baseline HFC emissions over the entire period 2018–2050. The marginal cost of meeting the KA targets is expected to remain below 60 €/t CO₂eq throughout the period in all world regions except for developed regions where legislation to control HFC emissions has already been in place since a few years. For the latter regions, the required HFC consumption reduction is expected to come at a marginal cost increasing steadily to between 90 and 118 €/t CO₂eq in 2050. Depending on the expected rate of technological development and the extent to which envisaged electricity savings can be realized, compliance with KA is estimated attainable at a global cost ranging from a net cost-saving of 240 billion € to a net cost of 350 billion € over the entire period 2018 to 2050 and with future global electricity-savings estimated at between 0.2% and 0.7% of expected future electricity consumption.     

Environmental performance comparison of wet and thermal routes for phosphate fertilizer production using LCA – A Brazilian experience

Life cycle assessment (LCA) was applied to perform an environmental comparison between the phosphate fertilizers fused magnesium phosphate (FMP) and triple superphosphate (TSP). In order to perform the comparison a functional unit (FU) of 41.66 kg P₂O₅, which corresponds to 208 kg FMP (20% P₂O₅) and 93 kg TSP (45% P₂O₅) was defined. Concerning the product systems a “cradle to gate” approach was used in both cases. In order to perform the life cycle impact assessment (LCIA) the impact categories: global warming potential (GWP), ozone depletion potential (ODP), human toxicity potential (HTP), fresh water aquatic ecotoxicity potential (FWAETP), acidification potential (AP) and eutrophication potential (EP) were selected. The development of this step was accomplished using CML 2 baseline 2000 method, with the help of the computational tool SimaPro 5, version 5.1.0.21. The study identified that in the case of FMP, the extensive electricity dependence is the main source of potential negative environmental impacts. On the other hand, for the TSP, the great distances between the phosphate rock mines and the main manufacture centers for both H₃PO₄ and TSP together with the transportation model adopted in this country appear as the main causes of environmental impacts.     

Modelling greenhouse gas emissions from European conventional and organic dairy farms

Agriculture is an important contributor to global emissions of greenhouse gases (GHG), in particular for methane (CH₄) and nitrous oxide (N₂O). Emissions from farms with a stock of ruminant animals are particularly high due to CH₄ emissions from enteric fermentation and manure handling, and due to the intensive nitrogen (N) cycle on such farms leading to direct and indirect N₂O emissions. The whole-farm model, FarmGHG, was designed to quantify the flows of carbon (C) and nitrogen (N) on dairy farms. The aim of the model was to allow quantification of effects of management practices and mitigation options on GHG emissions. The model provides assessments of emissions from both the production unit and the pre-chains. However, the model does not quantify changes in soil C storage.Model dairy farms were defined within five European agro-ecological zones for both organic and conventional systems. The model farms were all defined to have the same utilised agricultural area (50 ha). Cows on conventional and organic model farms were defined to achieve the same milk yield, so the basic difference between conventional and organic farms was expressed in the livestock density. The organic farms were defined to be 100% self-sufficient with respect to feed. The conventional farms, on the other hand, import concentrates as supplementary feed and their livestock density was defined to be 75% higher than the organic farm density. Regional differences between farms were expressed in the milk yield, the crop rotations, and the cow housing system and manure management method most common to each region.The model results showed that the emissions at farm level could be related to either the farm N surplus or the farm N efficiency. The farm N surplus appeared to be a good proxy for GHG emissions per unit of land area. The GHG emissions increased from 3.0 Mg CO₂-eq ha⁻¹ year⁻¹ at a N surplus of 56 kg N ha⁻¹ year⁻¹ to 15.9 Mg CO₂-eq ha⁻¹ year⁻¹ at a N surplus of 319 kg N ha⁻¹ year⁻¹. The farm N surplus can relatively easily be determined on practical farms from the farm records of imports and exports and the composition of the crop rotation. The GHG emissions per product unit (milk or metabolic energy) were quite closely related to the farm N efficiency, and a doubling of the N efficiency from 12.5 to 25% reduced the emissions per product unit by ca. 50%. The farm N efficiency may therefore be used as a proxy for comparing the efficiencies of farms with respect to supplying products with a low GHG emission.     

Nitrous oxide emissions from organic and conventional crop rotations in five European countries

Nitrous oxide (N₂O) emissions from agriculture are currently estimated from N inputs using emission factors, and little is known about the importance of regional or management-related differences. This paper summarizes the results of a study in which N₂O emission rates were recorded on 15–26 occasions during a 12-month period in organic and conventional dairy crop rotations in five European countries (Austria, Denmark, Finland, Italy, UK). A common methodology based on static chambers was used for N₂O flux measurements, and N₂O data were compiled together with information about N inputs (from fertilizers, N₂ fixation, atmospheric deposition and excretal returns), crop rotations and soil properties. Organic rotations received only manure as N fertilizer, while manure accounted for 0–100% of fertilizer N in conventional rotations. A linear regression model was used to examine effects of location, system and crop category on N₂O emissions, while a second model examined effects of soil properties. Nitrous oxide emissions were higher from conventional than from organic crop rotations except in Austria and, according to the statistical analysis, the differences between locations and crop categories were significant. Ammonium was significantly related to N₂O emissions, although this effect was dominated by observations from a grazing system. Despite the limited number of samplings, annual emissions were estimated by interpolation. Across the two systems and five locations there was a significant relationship between total N inputs and N₂O emissions at the crop rotation level which indicated that annually 1.6 ± 0.2% (mean ± standard error) of total N inputs were lost as N₂O, while there was a background emission of 1.4 ± 0.3 kg N₂O-N ha⁻¹ year⁻¹. Although this measurement program emphasized system effects at the expense of high temporal resolution, the results indicate that N input is a significant determinant for N₂O emissions from agricultural soils.     

Simultaneous removal of arsenic and antimony from mining wastewater using granular TiO2: Batch and field column studies

Coexisting arsenic (As) and antimony (Sb) in mining wastewater is a common and great concern. On-site simultaneous removal of As and Sb from mining wastewater was achieved by using a reusable granular TiO₂ column in this study. To evaluate the accuracy of the scale-up procedure, As and Sb adsorption from wastewater was studied in both large (600 g TiO₂) and small columns (12 g TiO₂) based on the proportional diffusivity rapid small-scale column tests (PD-RSSCTs) design. The comparable As and Sb breakthrough curves obtained from small and large columns confirmed the accuracy of the PD-RSSCT theory in the design of large-scale columns. Meanwhile, the consistent As and Sb adsorption results from batch and column experiments suggested that TiO₂ adsorption for As and Sb can be predicted from bench-scale tests. Charge distribution multi-site complexation (CD-MUSIC) and one-dimensional transport modeling integrated in the PHREEQC program were performed to study the adsorption behaviors of As and Sb on the TiO₂ surface. Coexisting ions, such as Ca^2 +, Mg^2 +, and Si^4 +, play an important role in As and Sb adsorption, and the breakthrough curves were well simulated after considering the compound ion effects. The results from this study highlight the surface reactions of As and Sb on TiO₂ and provide a practical way for on-site remediation of industrial wastewater.     

The water footprint of food waste: case study of fresh mango in Australia

In many parts of the world, freshwater is already a scarce and overexploited natural resource, raising concerns about global food security and damage to freshwater ecosystems. This situation is expected to intensify with the FAO estimating that world food production must double by 2050. Food chains must therefore become much more efficient in terms of consumptive water use. For the small and geographically well-defined Australian mango industry, having an average annual production of 44,692 t of marketable fresh fruit, the average virtual water content (sum of green, blue and gray water) at orchard gate was 2298 l kg^?1. However, due to wastage in the distribution and consumption stages of the product life cycle, the average virtual water content of 1 kg of Australian-grown fresh mango consumed by an Australian household was 5218 l. This latter figure compares to an Australian-equivalent water footprint of 217 l kg^?1, which is the volume of direct water use in Australia having an equivalent potential to contribute to water scarcity. Nationally, distribution and consumption waste in the food chain of Australian-grown fresh mango to Australian households represented an annual waste of 26.7 Gl of green water and 16.6 Gl of blue water. These findings suggest that interventions to reduce food chain waste will likely have as great or even greater impact on freshwater resource availability as other water use efficiency measures in agriculture and food production.     

Effects of irrigation,fertilization and crop straw management on nitrous oxide and nitric oxide emissions from a wheat–maize rotation field in northern China

One-year winter wheat–summer maize rotation is the most popular double cropping system in north-central China, and this highly productive system is an important source of nitrous oxide (N₂O) and nitric oxide (NO) emissions due to the high fertilizer N and irrigation water inputs. To sustain the high crop production and mitigate the detrimental impacts of N₂O and NO emissions, improved management practices are extensively applied. The aim of this study is therefore to evaluate the effects of an improved management practice of irrigation, fertilization and crop straw on grain yield and N₂O and NO emissions for a wheat–maize rotation field in northern China. Using automated and manual chamber measuring systems, we monitored N₂O and NO fluxes for the conventional (CT, 2007–2008), improved (IT, 2007–2008), straw-amended (WS, 2008–2009), straw-not-amended (NS, 2008–2009), and no N-fertilizer treatments (WS–NN, 2008–2009), respectively, for one rotation-year. The grain yields were determined for CT and IT for three rotation-years (2005–2008) and for WS, NS and WS–NN for one rotation-year (2008–2009). The improved management of irrigation and fertilization reduced the annual N fertilization rate and irrigation amount by 17% and 30%, respectively; increased the maize yield by 7–14%; and significantly decreased the N₂O and NO emissions by 7% (p < 0.05) and 29% (p < 0.01), respectively. The incorporation of wheat straw increased the cumulative N₂O and NO emissions in the following maize season by 58% (p < 0.01) and 13%, respectively, whereas the effects of maize straw application were not remarkable. The N₂O and NO emission factors of applied N were 2.32 ± 2.32% and 0.42 ± 1.69% for wheat straw and 0.67 ± 0.23% and 0.54 ± 0.15% for chemical N-fertilizers, respectively. Compared to conventional management practices using high application rates of irrigation water and chemical N-fertilizer as well as the field burning of crop straw, the improved management strategy presented here has obvious environmentally positive effects on grain yield and mitigation of N₂O and NO emissions.     

Biogas production from maize and dairy cattle manure—Influence of biomass composition on the methane yield

There is an increasing world wide demand for energy crops and animal manures for biogas production. To meet these demands, this research project aimed at optimising anaerobic digestion of maize and dairy cattle manures. Methane production was measured for 60 days in 1 l eudiometer batch digesters at 38 °C. Manure received from dairy cows with medium milk yield that were fed a well balanced diet produced the highest specific methane yield of 166.3 Nl CH₄ kg VS⁻¹. Thirteen early to late ripening maize varieties were grown on several locations in Austria. Late ripening varieties produced more biomass than medium or early ripening varieties. On fertile locations in Austria more than 30 Mg VS ha⁻¹ can be produced. The methane yield declined as the crop approaches full ripeness. With late ripening maize varieties, yields ranged between 312 and 365 Nl CH₄ kg VS⁻¹ (milk ripeness) and 268–286 Nl CH₄ kg VS⁻¹ (full ripeness). Silaging increased the methane yield by about 25% compared to green, non-conserved maize. Maize (Zea mays L.) is optimally harvested, when the product from specific methane yield and VS yield per hectare reaches a maximum. With early to medium ripening varieties (FAO 240–390), the optimum harvesting time is at the “end of wax ripeness”. Late ripening varieties (FAO ca. 600) may be harvested later, towards “full ripeness”. Maximum methane yield per hectare from late ripening maize varieties ranged between 7100 and 9000 Nm³ CH₄ ha⁻¹. Early and medium ripening varieties yielded 5300–8500 Nm³ CH₄ ha⁻¹ when grown in favourable regions. The highest methane yield per hectare was achieved from digestion of whole maize crops. Digestion of corns only or of corn cob mix resulted in a reduction in methane yield per hectare of 70 and 43%, respectively. From the digestion experiments a multiple linear regression equation, the Methane Energy Value Model, was derived that estimates methane production from the composition of maize. It is a helpful tool to optimise biogas production from energy crops. The Methane Energy Value Model requires further validation and refinement.     

Disaggregated greenhouse gas emission inventories from agriculture via a coupled economic-ecosystem model

Estimates of regional greenhouse gas emissions from agricultural systems are needed to evaluate possible mitigation strategies with respect to environmental effectiveness and economic feasibility. Therefore, in this study, we used the GIS-coupled economic-ecosystem model EFEM–DNDC to assess disaggregated regional greenhouse gas (GHG) emissions from typical livestock and crop production systems in the federal state of Baden-Württemberg, Southwest Germany. EFEM is an economic farm production model based on linear programming of typical agricultural production systems and simulates all relevant farm management processes and GHG emissions. DNDC is a process-oriented ecosystem model that describes the complete biogeochemical C and N cycle of agricultural soils, including all trace gases.Direct soil emissions were mainly related to N₂O, whereas CH₄ uptake had marginal influence (net soil C uptake or release was not considered). The simulated N₂O emissions appeared to be highly correlated to N fertilizer application (R² = 0.79). The emission factor for Baden-Württemberg was 0.97% of the applied N after excluding background emissions.Analysis of the production systems showed that total GHG emissions from crop based production systems were considerably lower (2.6–3.4 Mg CO₂ eq ha⁻¹) than from livestock based systems (5.2–5.3 Mg CO₂ eq ha⁻¹). Average production system GHG emissions for Baden-Württemberg were 4.5 Mg CO₂ eq ha⁻¹. Of the total 38% were derived from N₂O (direct and indirect soil emissions, and manure storage), 40% were from CH₄ (enteric fermentation and manure storage), and 22% were from CO₂ (mainly fertilizer production, gasoline, heating, and additional feed). The stocking rate was highly correlated (R² = 0.85) to the total production system GHG emissions and appears to be a useful indicator of regional emission levels.     

Biological hydrogen production by Rhodobacter capsulatus in solar tubular photo bioreactor

The purpose of this study was to develop a pilot scale tubular photo bioreactor (80 L) for photo fermentative hydrogen production by photosynthetic purple-non-sulfur bacterium, Rhodobacter capsulatus, operating in outdoor conditions, using acetate as the carbon source. The reactor was operated continuously in fed-batch mode for 30 days throughout December 2008 in Ankara. It was placed in a greenhouse in order to keep the temperature above freezing levels. It was found that R. capsulatus had a rapid growth with a specific growth rate of 0.025 h^?1 in the exponential phase. The growth was defined with modified logistic model for long term duration. The hydrogen production and feeding started in the late exponential phase. Evolved gas contained 99% hydrogen and 1% carbon dioxide by volume. The average molar productivity calculated during daylight hour was 0.31 mol H₂/(m³ h) with regard to the total reactor volume and 0.112 mol H₂/(m²·day) with regard to the total illuminated surface area. It was proven that even at low light intensities and low temperatures, the acetic acid which was fed to the system can be utilized for biosynthesis, growth and hydrogen production. The overall hydrogen yield was 0.6 mole H₂ per mole of acetic acid fed. This study showed that photofermentation in a pilot scale tubular photo bioreactor can produce hydrogen, even in winter conditions.     

Emissions of N2O and NH3, and nitrogen leaching from direct seeded rice under different tillage practices in central China

Tillage practices affect the fate of fertilizer nitrogen (N) through influencing transformations of N, but few studies have examined N₂O and NH₃ emissions, and N leaching from different rice tillage systems. Thus the objective of this study was to assess N₂O emission, NH₃ volatilization and N leaching from direct seeded rice in conventional tillage (CT) and no-tillage (NT) production systems in the subtropical region of China during the 2008 and 2009 rice growing seasons. Treatments were established following a split-plot design of a randomized complete block with tillage practices as the main plot and N fertilizer level as the sub-plot treatment, and there were four treatments: NT + no fertilizer (NT0), CT + no fertilizer (CT0), NT + compound fertilizer (NTC) and CT + compound fertilizer (CTC), respectively. Results showed that N fertilization significantly increased (p < 0.01) N₂O emissions, NH₃ volatilization and N leaching from rice fields in both years. In general, there was no significant difference in N₂O emissions and NH₃ volatilization between NT0 and CT0 in both years, while NTC had significantly higher (p < 0.05) N₂O emissions and NH₃ volatilization compared to CTC. Over the two rice growing seasons, NTC showed 32% and 47% higher N₂O emissions, and 29% and 52% higher NH₃ losses than CTC. Higher (p < 0.05) N₂O emissions from NTC than CTC were presumably due to higher soil organic C and greater denitrification. Total N and NO₃^? concentrations were higher (p < 0.05) in CTC than NTC, but larger volumes of percolation water in NTC than CTC resulted in no significant difference in leakage of total N and NO₃^?. Hence, application of N fertilizer in combination with NT appeared to be ineffective in reducing N losses from N fertilizer in paddy fields.     

The social and spatial distribution of temperature-related health impacts from urban heat island reduction policies

Cities are developing innovative strategies to combat climate change but there remains little knowledge of the winners and losers from climate-adaptive land use planning and design. We examine the distribution of health benefits associated with land use policies designed to increase vegetation and surface reflectivity in three US metropolitan areas: Atlanta, GA, Philadelphia, PA, and Phoenix, AZ. Projections of population and land cover at the census tract scale were combined with climate models for the year 2050 at 4 km × 4 km resolution to produce future summer temperatures which were input into a comparative risk assessment framework for the temperature-mortality relationship. The findings suggest disparities in the effectiveness of urban heat management strategies by age, income, and race. We conclude that, to be most protective of human health, urban heat management must prioritize areas of greatest population vulnerability.     

Hermetic joining of 316L stainless steel using a patterned nickel nanoparticle interlayer

This paper evaluates the use of a nickel nanoparticle (NiNP) interlayer for making hermetic joints in 316L stainless steel substrates via diffusion brazing. Different NiNP inks were prepared using commercial nanopowder (～9 nm) and in-house synthesized nanoparticles. Syringe pump deposition of ～9 nm NiNP ink and diffusion brazing at 900 °C for 30 min under 2 MPa resulted in a hermetic joint up to the tested pressure of 70 psi. In-house synthesis of NiNPs was carried out in ethylene glycol by the reduction of NiCl₂·6H₂O in the presence of hydrazine (N₂H₄) as a reducing agent. X-ray diffraction (XRD) analysis and transmission electron microscopy (TEM) results confirm the presence of pure fcc-Ni with an average particle size of 5.4 ± 0.9 nm. An as-synthesized suspension of NiNPs was patterned onto 316L stainless steel laminae via automated dispensing to a thickness of ～3 μm and bonded at 800 °C for 30 min at a pressure of 2 MPa. The diffusion-brazed test article was also found to be hermetic up to 70 psi. An examination of the bond line using scanning electron microscopy (SEM) showed good uniformity and continuity.     

The influence of long term trends in pollutant emissions on deposition of sulphur and nitrogen and exceedance of critical loads in the United Kingdom

In the United Kingdom, as with other European countries, land-based emissions of NO_x and SO₂ have fallen significantly over the last few decades. SO₂ emissions fell from a peak of 3185 Gg S in 1970 to 344 Gg S in 2005 and are forecast by business-as-usual emissions scenarios to fall to 172 Gg by 2020. NO_x emissions were at a maximum of 951 Gg N in 1970 and fell to 378 by 2005 with a further decrease to 243 Gg N forecast by 2020. These large changes in emissions have not been matched by emissions changes for NH₃ which decreased from 315 Gg N in 1990 to 259 in 2005 and are forecast to fall to 222 by 2020. The Fine Resolution Atmospheric Multi-pollutant Exchange model (FRAME) has been applied to model the spatial distribution of sulphur and nitrogen deposition over the United Kingdom during a 15-year time period (1990–2005) and compared with measured deposition of sulphate, nitrate and ammonium from the national monitoring network. Wet deposition of nitrogen and sulphur was found to decrease more slowly than the emissions reductions rate. This is attributed to a number of factors including increases in emissions from international shipping and changing rates of atmospheric oxidation. The modelled time series was extended to a 50-year period from 1970 to 2020. The modelled deposition of SO_x, NO_y and NH_x to the UK was found to fall by 87%, 52% and 25% during this period. The percentage area of sensitive habitats in the United Kingdom for which critical loads are exceeded is estimated to fall from 85% in 1970 to 37% in 2020 for acidic deposition and from 73% to 49% for nutrient nitrogen deposition. The significant reduction in land emissions of SO₂ and NO_x focuses further attention in controlling emissions from international shipping. Future policies to control emissions of ammonia from agriculture will be required to effect further significant reductions in nitrogen deposition.     

Modeling increased demand of energy for air conditioners and consequent CO2 emissions to minimize health risks due to climate change in India

Developing countries situated mostly in latitudes that are projected for the highest climate change impact in the twenty-first century will also have a predictable increase in demand on energy sources. India presents us with a unique opportunity to study this phenomenon in a large developing country. This study finds that climate adaptation policies of India should consider the significance of air conditioners (A/Cs) in mitigation of human vulnerability due to unpredictable weather events such as heat waves. However, the energy demand due to air conditioning usage alone will be in the range of an extra ～750,000 GWh to ～1,350,000 GWh with a 3.7 °C increase in surface temperatures under different population scenarios and increasing incomes by the year 2100. We project that residential A/C usage by 2100 will result in CO₂ emissions of 592 Tg to 1064 Tg. This is significant given that India's total contribution to global CO₂ emissions in 2009 was measured at 1670 Tg and country's residential and commercial electricity consumption in 2007 was estimated at 145,000 GWh.     

Evaluation of two soil carbon models using two Kenyan long term experimental datasets

RothC and Century are two of the most widely used soil organic matter (SOM) models. However there are few examples of specific parameterisation of these models for environmental conditions in East Africa. The aim of this study was therefore, to evaluate the ability of RothC and the Century to estimate changes in soil organic carbon (SOC) resulting from varying land use/management practices for the climate and soil conditions found in Kenya. The study used climate, soils and crop data from a long term experiment (1976–2001) carried out at The Kabete site at The Kenya National Agricultural Research Laboratories (NARL, located in a semi-humid region) and data from a 13 year experiment carried out in Machang’a (Embu District, located in a semi-arid region). The NARL experiment included various fertiliser (0, 60 and 120 kg of N and P₂O₅ ha⁻¹), farmyard manure (FYM—5 and 10 t ha⁻¹) and plant residue treatments, in a variety of combinations. The Machang’a experiment involved a fertiliser (51 kg N ha⁻¹) and a FYM (0, 5 and 10 t ha⁻¹) treatment with both monocropping and intercropping. At Kabete both models showed a fair to good fit to measured data, although Century simulations for treatments with high levels of FYM were better than those without. At the Machang’a site with monocrops, both models showed a fair to good fit to measured data for all treatments. However, the fit of both models (especially RothC) to measured data for intercropping treatments at Machang’a was much poorer. Further model development for intercrop systems is recommended. Both models can be useful tools in soil C predictions, provided time series of measured soil C and crop production data are available for validating model performance against local or regional agricultural crops.     

Toward chemical-free reclamation of biologically pretreated greywater: solar photocatalytic oxidation with powdered activated carbon

Heterogeneous photocatalytic oxidation is a water reclamation technology which avoids chemical consumption and can be powered by solar radiation. Because this generally sustainable process is of limited efficiency for the treatment of biologically pretreated greywater, it was combined with activated carbon adsorption. The effluent of a constructed wetland for treatment of separately collected greywater was subjected to photocatalytic oxidation using the photocatalyst titanium dioxide (TiO₂) “P25” in both the absence and the presence of powdered activated carbon (PAC). Photocatalytic oxidation alone with UV fluences of about 10 Wh L^?1 was not capable of reducing total organic carbon (TOC) from an initial concentration of 5.5 mg L^?1 safely below 2 mg L^?1 as a prerequisite for high-quality water reuse purposes. However, when PAC was added, TOC concentrations subsequent to photocatalytic oxidation were less than 2 mg L^?1 even after reusing the TiO₂/PAC mixture 10 times. PAC addition is estimated to reduce the insolation area necessary to achieve this target by solar photocatalytic oxidation of biologically treated greywater by a factor 7. This combination process represents an innovative chemical-free technology within wastewater reuse schemes.     

Development and characterization of microwave composite cladding

The development of cladding through microwave radiation is recently explored and very few, initial studies were reported elsewhere. In order to explore more viability of process, (EWAC (Ni based) + 20% Cr₂₃C₆ powder) composite cladding has been developed on substrate austenitic stainless steel (SS-316). The experiments were conducted in domestic microwave oven and the clad of thickness, approximate 500 m has been developed by the exposure of microwave radiation at frequency 2.45 GHz for duration of 360 s. Typical clads cross sections of composite clads showed good metallurgical bonding with the substrate by partial dilution. The back scattered electron image of clad cross section showed the reinforced chromium carbide (Cr₂₃C₆) particles are uniformly distributed and well embedded in the Ni based matrix. The developed clad is free from visible solidification cracking and has significantly less porosity which is of the order of 0.90%. The XRD pattern of the developed clad showed the presence of FeNi₃, NiSi and Cr₂₃C₆ phases. The average Vicker's microhardness of developed clad was observed as 425 ± 140 Hv.     

Lodging in rice can be alleviated by atmospheric CO2 enrichment

The projected increase of atmospheric CO₂ concentration [CO₂] is expected to increase yield of agricultural C₃ crops, but little is known about effects of [CO₂] on lodging that can reduce yield. This study examined the interaction between [CO₂] and nitrogen (N) fertilization on the lodging of rice (Oryza sativa L.) using free-air CO₂ enrichment (FACE) systems installed in paddy fields at Shizukuishi, Iwate, Japan (39°38′N, 140°57′E). Rice plants were grown under two levels of [CO₂] (ambient = 365 μmol mol⁻¹; elevated [CO₂] = 548 μmol mol⁻¹) and three N fertilization regimes: a single initial basal application of controlled-release urea (8 g N m⁻², CRN), split fertilization with a standard amount of ammonium sulfate (9 g N m⁻², MN), and ample N (15 g N m⁻², HN). Lodging score (six ranks at 18° intervals, with larger scores indicating greater bending), yield, and yield components were measured at maturity. The lodging score was significantly higher under HN than under CRN and MN, but lodging was alleviated by elevated [CO₂] under HN. This alleviation was associated with the shortened and thickened lower internodes, but was not associated with a change in the plant's mass moment around the culm base. A positively significant correlation between lodging score and ripening percentage indicated that ripening percentage decreased by 4.5% per one-unit increase in lodging score. These findings will be useful to develop functional algorithm that can be incorporated into mechanistic crop models to predict rice production more accurately in a changing climate and with different cultural practices.