Estimating and comparing greenhouse gas emissions with their uncertainties using different methods: A case study for an energy supply utility

Energy supply utilities release significant amounts of greenhouse gases (GHGs) into the atmosphere. It is essential to accurately estimate GHG emissions with their uncertainties, for reducing GHG emissions and mitigating climate change. GHG emissions can be calculated by an activity-based method (i.e., fuel consumption) and continuous emission measurement (CEM). In this study, GHG emissions such as CO₂, CH₄, and N₂O are estimated for a heat generation utility, which uses bituminous coal as fuel, by applying both the activity-based method and CEM. CO₂ emissions by the activity-based method are 12–19% less than that by the CEM, while N₂O and CH₄ emissions by the activity-based method are two orders of magnitude and 60% less than those by the CEM, respectively. Comparing GHG emissions (as CO₂ equivalent) from both methods, total GHG emissions by the activity-based methods are 12–27% lower than that by the CEM, as CO₂ and N₂O emissions are lower than those by the CEM. Results from uncertainty estimation show that uncertainties in the GHG emissions by the activity-based methods range from 3.4% to about 20%, from 67% to 900%, and from about 70% to about 200% for CO₂, N₂O, and CH₄, respectively, while uncertainties in the GHG emissions by the CEM range from 4% to 4.5%. For the activity-based methods, an uncertainty in the Intergovernmental Panel on Climate Change (IPCC) default net calorific value (NCV) is the major uncertainty contributor to CO₂ emissions, while an uncertainty in the IPCC default emission factor is the major uncertainty contributor to CH₄ and N₂O emissions. For the CEM, an uncertainty in volumetric flow measurement, especially for the distribution of the volumetric flow rate in a stack, is the major uncertainty contributor to all GHG emissions, while uncertainties in concentration measurements contribute a little to uncertainties in the GHG emissions.

Implications:Energy supply utilities contribute a significant portion of the global greenhouse gas (GHG) emissions. It is important to accurately estimate GHG emissions with their uncertainties for reducing GHG emissions and mitigating climate change. GHG emissions can be estimated by an activity-based method and by continuous emission measurement (CEM), yet little study has been done to calculate GHG emissions with uncertainty analysis. This study estimates GHG emissions and their uncertainties, and also identifies major uncertainty contributors for each method.     

Greenhouse gas emissions from the waste sector in Argentina in business-as-usual and mitigation scenarios

The objective of this work was the application of 2006 Intergovernmental Panel on Climate Change (IPCC) Guidelines for the estimation of methane and nitrous oxide emissions from the waste sector in Argentina as a preliminary exercise for greenhouse gas (GHG) inventory development and to compare with previous inventories based on 1996 IPCC Guidelines. Emissions projections to 2030 were evaluated under two scenarios—business as usual (BAU), and mitigation—and the calculations were done by using the ad hoc developed IPCC software. According to local activity data, in the business-as-usual scenario, methane emissions from solid waste disposal will increase by 73% by 2030 with respect to the emissions of year 2000. In the mitigation scenario, based on the recorded trend of methane captured in landfills, a decrease of 50% from the BAU scenario should be achieved by 2030. In the BAU scenario, GHG emissions from domestic wastewater will increase 63% from 2000 to 2030. Methane emissions from industrial wastewater, calculated from activity data of dairy, swine, slaughterhouse, citric, sugar, and wine sectors, will increase by 58% from 2000 to 2030 while methane emissions from domestic will increase 74% in the same period. Results show that GHG emissions calculated from 2006 IPCC Guidelines resulted in lower levels than those reported in previous national inventories for solid waste disposal and domestic wastewater categories, while levels were 18% higher for industrial wastewater.

Implications: The implementation of the 2006 IPCC Guidelines for National Greenhouse Inventories is now considering by the UNFCCC for non-Annex I countries in order to enhance the compilation of inventories based on comparable good practice methods. This work constitutes the first GHG emissions estimation from the waste sector of Argentina applying the 2006 IPCC Guidelines and the ad doc developed software. It will contribute to identifying the main differences between the models applied in the estimation of methane emissions on the key categories of waste emission sources and to comparing results with previous inventories based on 1996 IPCC Guidelines.     

Understanding interactions between urban development policies and GHG emissions: A case study in Stockholm Region

Human-induced urban growth and sprawl have implications for greenhouse gas (GHG) emissions that may not be included in conventional GHG accounting methods. Improved understanding of this issue requires use of interactive, spatial-explicit social–ecological systems modeling. This paper develops a comprehensive approach to modeling GHG emissions from urban developments, considering Stockholm County, Sweden as a case study. GHG projections to 2040 with a social–ecological system model yield overall greater emissions than simple extrapolations in official climate action planning. The most pronounced difference in emissions (39% higher) from energy use single-residence buildings resulting from urban sprawl. And this difference is not accounted for in the simple extrapolations. Scenario results indicate that a zoning policy, restricting urban development in certain areas, can mitigate 72% of the total emission effects of the model-projected urban sprawl. The study outcomes include a decision support interface for communicating results and policy implications with policymakers.

     

Life cycle and economic assessment of source-separated MSW collection with regard to greenhouse gas emissions: a case study in China

In China, the continuously increasing amount of municipal solid waste (MSW) has resulted in an urgent need for changing the current municipal solid waste management (MSWM) system based on mixed collection. A pilot program focusing on source-separated MSW collection was thus launched (2010) in Hangzhou, China, to lessen the related environmental loads. And greenhouse gas (GHG) emissions (Kyoto Protocol) are singled out in particular. This paper uses life cycle assessment modeling to evaluate the potential environmental improvement with regard to GHG emissions. The pre-existing MSWM system is assessed as baseline, while the source separation scenario is compared internally. Results show that 23 % GHG emissions can be decreased by source-separated collection compared with the base scenario. In addition, the use of composting and anaerobic digestion (AD) is suggested for further optimizing the management of food waste. 260.79, 82.21, and ?86.21 thousand tonnes of GHG emissions are emitted from food waste landfill, composting, and AD, respectively, proving the emission reduction potential brought by advanced food waste treatment technologies. Realizing the fact, a modified MSWM system is proposed by taking AD as food waste substitution option, with additional 44 % GHG emissions saved than current source separation scenario. Moreover, a preliminary economic assessment is implemented. It is demonstrated that both source separation scenarios have a good cost reduction potential than mixed collection, with the proposed new system the most cost-effective one.     

A Top-Down Regional Assessment of Urban Greenhouse Gas Emissions in Europe

This paper provides an account of urban greenhouse gas (GHG) emissions from 40 countries in Europe and examines covariates of emissions levels. We use a “top-down” analysis of emissions as spatially reported in the Emission Dataset for Global Atmospheric Research supplemented by Carbon Monitoring for Action from 1153 European cities larger than 50 000 population in 2000 (comprising >81 % of the total European urban population). Urban areas are defined spatially and demographically by the Global Rural Urban Mapping Project. We compare these results with “bottom-up” carbon accounting method results for cities in the region. Our results suggest that direct (Scopes 1 and 2) GHG emissions from urban areas range between 44 and 54 % of total anthropogenic emissions for the region. While individual urban GHG footprints vary from bottom-up studies, both the mean differences and the regional energy-related GHG emission share support previous findings. Correlation analysis indicates that the urban GHG emissions in Europe are mainly influenced by population size, density, and income and not by biophysical conditions. We argue that these data and methods of analysis are best used at the regional or higher scales.     

发达国家温室气体减排现状及对我国的启示

气候变化是当前全世界关注的焦点问题,大气中温室气体浓度的不断升高与人类活动存在密切的联系.温室气体的历史排放主要是由发达国家产生的,发达国家对气候变化负有主要的责任.目前发达国家温室气体减排履约的整体情况不容乐观,主要发达国家的排放量呈上升趋势,但一些发达国家的减排经验还是值得借鉴的.本文在总结发达国家温室气体减排政策和措施的基础上,结合我国实际情况,提出了我国温室气体减排的可能对策.     

Reduction in greenhouse gas emissions from sludge biodrying instead of heat drying combined with mono-incineration in China

Sludge is an important source of greenhouse gas (GHG) emissions, both in the form of direct process emissions and as a result of indirect carbon-derived energy consumption during processing. In this study, the carbon budgets of two sludge disposal processes at two well-known sludge disposal sites in China (for biodrying and heat-drying pretreatments, both followed by mono-incineration) were quantified and compared. Total GHG emissions from heat drying combined with mono-incineration was 0.1731 tCO₂e t^?1, while 0.0882 tCO₂e t^?1 was emitted from biodrying combined with mono-incineration. Based on these findings, a significant reduction (approximately 50%) in total GHG emissions was obtained by biodrying instead of heat drying prior to sludge incineration.

Implications: Sludge treatment results in direct and indirect greenhouse gas (GHG) emissions. Moisture reduction followed by incineration is commonly used to dispose of sludge in China; however, few studies have compared the effects of different drying pretreatment options on GHG emissions during such processes. Therefore, in this study, the carbon budgets of sludge incineration were analyzed and compared following different pretreatment drying technologies (biodrying and heat drying). The results indicate that biodrying combined with incineration generated approximately half of the GHG emissions compared to heat drying followed by incineration. Accordingly, biodrying may represent a more environment-friendly sludge pretreatment prior to incineration.     

A contemporary landscape of air pollution and greenhouse gas emissions leads to inevitable phenomena of low birthweight

The objective of the study is to empirically examine the air pollution, greenhouse gas (GHG) emissions and low birth weight in Pakistan through the cointegration and error correction model over a 36-year time period, i.e., between 1975 and 2012. The study employed the Johansen cointegration technique to estimate the long-run relationship between the variables, while an error correction model was used to determine the short-run dynamics of the system. The study was limited to the following variables, including carbon dioxide emissions, methane emissions, nitrous oxide emissions, GHG emissions, and low birth weight in order to manage robust data analysis. The results reveal that air pollution and GHG emissions significantly affects the low birth weight in Pakistan. In the long run, carbon dioxide emissions act as a strong contributor for low birth weight, as the coefficient value indicates there is a more elastic relationship (i.e., ?1.214, p?p?p?相似文献   

Environmental assessment on electrokinetic remediation of multimetal-contaminated site: a case study

In this study, an environmental assessment on an electrokinetic (EK) system for the remediation of a multimetal-contaminated real site was conducted using a green and sustainable remediation (GSR) tool. The entire EK process was classified into major four phases consisting of remedial investigations (RIs), remedial action construction (RAC), remedial action operation (RAO), and long-term monitoring (LTM) for environmental assessment. The environmental footprints, including greenhouse gas (GHG) emissions, total energy used, air emissions of criteria pollutants, such as NO_x, SO_x, and PM₁₀, and water consumption, were calculated, and the relative contribution in each phase was analyzed in the environmental assessment. In the RAC phase, the relative contribution of the GHG emissions, total energy used, and PM₁₀ emissions were 77.3, 67.6, and 70.4 %, respectively, which were higher than those of the other phases because the material consumption and equipment used for system construction were high. In the RAO phase, the relative contributions of water consumption and NO_x and SO_x emissions were 94.7, 85.2, and 91.0 %, respectively, which were higher than those of the other phases, because the water and electricity consumption required for system operation was high. In the RIs and LTM phases, the environmental footprints were negligible because the material and energy consumption was less. In conclusion, the consumable materials and electrical energy consumption might be very important for GSR in the EK remediation process, because the production of consumable materials and electrical energy consumption highly affects the GHG emissions, total energy used, and air emissions such as NO_x and SO_x.     

A greenhouse gas emissions inventory for Pennsylvania

The Pennsylvania greenhouse gas (GHG) emissions inventory presented in this paper provides detailed estimates of emissions and their sources for the six major categories of GHGs. The inventory was compiled using the current U.S. Environment Protection Agency methodology, which applies emissions factors to socioeconomic data, such as fossil energy use, vehicle miles traveled, and industrial production. The paper also contains an assessment of the methodology and suggestions for improving accounting with respect to process, sectoral, and geographic considerations. The study found that Pennsylvania emitted 77.4 million metric tons carbon equivalent of GHGs in 1990 and that this total increased by 3% to 79.8 million metric tons carbon equivalent by 1999. Despite this increase, however, the state's percentage contribution to the United States total declined during the decade. Pennsylvania's carbon dioxide (CO2) emissions from fossil fuels represented 92.4% of 1990 totals and declined to 90.5% in 1999. Electricity generation was the largest single source of CO2 emissions, being responsible for 38% of fossil fuel CO2 emissions in 1990 and 40% of the total in 1999. Transportation emissions accounted for the largest increases in emissions between 1990 and 1999, whereas industrial emissions accounted for the largest decrease. The overall trend indicates that Pennsylvania has been able to weaken the relationship between GHG emissions and economic growth.     

Air quality co-benefits of subnational carbon policies

To mitigate climate change, governments ranging from city to multi-national have adopted greenhouse gas (GHG) emissions reduction targets. While the location of GHG reductions does not affect their climate benefits, it can impact human health benefits associated with co-emitted pollutants. Here, an advanced modeling framework is used to explore how subnational level GHG targets influence air pollutant co-benefits from ground level ozone and fine particulate matter. Two carbon policy scenarios are analyzed, each reducing the same total amount of GHG emissions in the Northeast US: an economy-wide Cap and Trade (CAT) program reducing emissions from all sectors of the economy, and a Clean Energy Standard (CES) reducing emissions from the electricity sector only. Results suggest that a regional CES policy will cost about 10 times more than a CAT policy. Despite having the same regional targets in the Northeast, carbon leakage to non-capped regions varies between policies. Consequently, a regional CAT policy will result in national carbon reductions that are over six times greater than the carbon reduced by the CES in 2030. Monetized regional human health benefits of the CAT and CES policies are 844% and 185% of the costs of each policy, respectively. Benefits for both policies are thus estimated to exceed their costs in the Northeast US. The estimated value of human health co-benefits associated with air pollution reductions for the CES scenario is two times that of the CAT scenario.

Implications: In this research, an advanced modeling framework is used to determine the potential impacts of regional carbon policies on air pollution co-benefits associated with ground level ozone and fine particulate matter. Study results show that spatially heterogeneous GHG policies have the potential to create areas of air pollution dis-benefit. It is also shown that monetized human health benefits within the area covered by policy may be larger than the model estimated cost of the policy. These findings are of particular interest both as U.S. states work to develop plans to meet state-level carbon emissions reduction targets set by the EPA through the Clean Power Plan, and in the absence of comprehensive national carbon policy.     

Estimating the carbon footprint of household activities in Japan from the time-use perspective

The household sector is a major driver of energy consumption and greenhouse gas (GHG) emissions. However, most existing studies have only estimated households’ carbon footprint from their expenditures. Households’ daily activity time, a scarce resource that limits and determines their consumption behavior, has rarely been integrated into the estimation. Incorporating the daily time-use patterns should thus provide a more practical perspective for mitigation policies aiming at promoting sustainable household lifestyles. In this study, by linking household time-use data and expenditure data of Japan, the carbon footprint and the GHG intensity of time of 85 daily household activities constituting the 24 hours in a day are estimated. Compared to the maximal 20-activity disaggregation in existing studies, our detailed 85-category disaggregation of daily time enables unprecedented details on the discrepancies between the carbon footprint from daily activities, many of which have previous been treated as one activity. Results indicate significant carbon mitigation potential in activities with a high GHG intensity of time, such as cooking, bathing, and mobility-related and activities. Average daily GHG emissions were also found to be higher on weekends as time-use patterns shift from paid work to free-time activities, highlighting the need for mitigation strategies on a weekly scale.

     

Preliminary investigation of greenhouse gas emissions from the environmental sector in Taiwan

The United Nations Framework Conventions on Climate Change (UNFCCC) asks their Parties to submit a National Inventory Report (NIR) for greenhouse gas (GHG) emissions on an annual basis. However, when many countries are quickly growing their economy, resulting in substantial GHG emissions, their inventory reporting systems either have not been established or been able to be linked to planning of mitigation measures at national administration levels. The present research was aimed to quantify the GHG emissions from an environmental sector in Taiwan and also to establish a linkage between the developed inventories and development of mitigation plans. The "environmental sector" consists of public service under jurisdiction of the Taiwan Environmental Protection Administration: landfilling, composting, waste transportation, wastewater treatment, night soil treatment, and solid waste incineration. The preliminary results were compared with that of the United States, Germany, Japan, United Kingdom, and Korea, considering the gaps in the scopes of the sectors. The GHG emissions from the Taiwanese environmental sector were mostly estimated by following the default methodology in the Intergovernmental Panel on Climate Change guideline, except that of night soil treatment and waste transportation that were modified or newly developed. The GHG emissions from the environmental sectors in 2004 were 10,225 kilotons of CO2 equivalent (kt CO2 Eq.). Landfilling (48.86%), solid waste incineration (27%), and wastewater treatment (21.5%) were the major contributors. Methane was the most significant GHG (70.6%), followed by carbon dioxide (27.8%) and nitrous oxide (1.6%). In summary, the GHG emissions estimated for the environmental sector in Taiwan provided reasonable preliminary results that were consistent and comparable with the existing authorized data. On the basis of the inventory results and the comparisons with the other countries, recommendations of mitigation plans were made, including wastewater and solid waste recycling, methane recovery for energy, and waste reduction/sorting.     

Environmental assessment on a soil washing process of a Pb-contaminated shooting range site: a case study

In this study, an environmental assessment on a soil washing process for the remediation of a Pb-contaminated shooting range site was conducted, using a green and sustainable remediation tool, i.e., SiteWise ver. 2, based on data relating specifically to the actual remediation project. The entire soil washing process was classified into four major stages, consisting of soil excavation (stage I), physical separation (stage II), acid-based (0.2 N HCl) chemical extraction (stage III), and wastewater treatment (stage IV). Environmental footprints, including greenhouse gas (GHG) emissions, energy consumption, water consumption, and critical air pollutant productions such as PM₁₀, NO _x , and SO _x , were calculated, and the relative contribution of each stage was analyzed in the environmental assessment. In stage I, the relative contribution of the PM₁₀ emissions was 55.3 % because the soil excavation emitted the fine particles. In stage II, the relative contribution of NO _x and SO _x emissions was 42.5 and 52.5 %, respectively, which resulted from electricity consumption for the operation of the separator. Stage III was the main contributing factor to 63.1 % of the GHG emissions, 67.5 % of total energy used, and 37.4 % of water consumptions. The relatively high contribution of stage III comes from use of consumable chemicals such as HCl and water-based extraction processes. In stage IV, the relative contributions of GHG emissions, total energy used, and NO _x and SO _x emissions were 23.2, 19.4, 19.5, and 25.3 %, respectively, which were caused by chemical and electricity demands for system operation. In conclusion, consumable chemicals such as HCl and NaOH, electric energy consumption for system operation, and equipment use for soil excavation were determined to be the major sources of environmental pollution to occur during the soil washing process. Especially, the acid-based chemical extraction process should be avoided in order to improve the sustainability of soil washing processes.     

Greenhouse gas emissions from waste management--assessment of quantification methods

Of the many sources of urban greenhouse gas (GHG) emissions, solid waste is the only one for which management decisions are undertaken primarily by municipal governments themselves and is hence often the largest component of cities' corporate inventories. It is essential that decision-makers select an appropriate quantification methodology and have an appreciation of methodological strengths and shortcomings. This work compares four different waste emissions quantification methods, including Intergovernmental Panel on Climate Change (IPCC) 1996 guidelines, IPCC 2006 guidelines, U.S. Environmental Protection Agency (EPA) Waste Reduction Model (WARM), and the Federation of Canadian Municipalities-Partners for Climate Protection (FCM-PCP) quantification tool. Waste disposal data for the greater Toronto area (GTA) in 2005 are used for all methodologies; treatment options (including landfill, incineration, compost, and anaerobic digestion) are examined where available in methodologies. Landfill was shown to be the greatest source of GHG emissions, contributing more than three-quarters of total emissions associated with waste management. Results from the different landfill gas (LFG) quantification approaches ranged from an emissions source of 557 kt carbon dioxide equivalents (CO2e) (FCM-PCP) to a carbon sink of -53 kt CO2e (EPA WARM). Similar values were obtained between IPCC approaches. The IPCC 2006 method was found to be more appropriate for inventorying applications because it uses a waste-in-place (WIP) approach, rather than a methane commitment (MC) approach, despite perceived onerous data requirements for WIP. MC approaches were found to be useful from a planning standpoint; however, uncertainty associated with their projections of future parameter values limits their applicability for GHG inventorying. MC and WIP methods provided similar results in this case study; however, this is case specific because of similarity in assumptions of present and future landfill parameters and quantities of annual waste deposited in recent years being relatively consistent.     

F-T合成技术生产替代燃料对环境的影响及对策

主要介绍了F-T合成柴油的特性,阐述了其作为清洁能源的优越性;利用生命周期清单分析方法,比较了以煤、生物质及天然气为原料采用F-T合成技术生产替代能源的工艺路线前提下,在提取生产、转化精炼、运输分配、最终用途燃烧、全部燃料链各阶段温室气体排放情况,提出了温室气体的减排对策。     

Greenhouse gas emissions from dairy open lot and manure stockpile in northern China: A case study

The open lots and manure stockpiles of dairy farm are major sources of greenhouse gas (GHG) emissions in typical dairy cow housing and manure management system in China. GHG (CO₂, CH₄ and N₂O) emissions from the ground level of brick-paved open lots and uncovered manure stockpiles were estimated according to the field measurements of a typical dairy farm in Beijing by closed chambers in four consecutive seasons. Location variation and manure removal strategy impacts were assessed on GHG emissions from the open lots. Estimated CO₂, CH₄ and N₂O emissions from the ground level of the open lots were 137.5±64.7 kg hd^-1 yr^-1, 0.45±0.21 kg hd^-1 yr^-1 and 0.13±0.08 kg hd^-1 yr^-1, respectively. There were remarkable location variations of GHG emissions from different zones (cubicle zone vs. aisle zone) of the open lot. However, the emissions from the whole open lot were less affected by the locations. After manure removal, lower CH₄ but higher N₂O emitted from the open lot. Estimated CO₂, CH₄ and N₂O emissions from stockpile with a stacking height of 55±12 cm were 858.9±375.8 kg hd^-1 yr^-1, 8.5±5.4 kg hd^-1 yr^-1 and 2.3±1.1 kg hd^-1 yr^-1, respectively. In situ storage duration, which estimated by manure volatile solid contents (VS), would affect GHG emissions from stockpiles. Much higher N₂O was emitted from stockpiles in summer due to longer manure storage.

Implications: This study deals with greenhouse gas (GHG) emissions from open lots and stockpiles. It’s an increasing area of concern in some livestock producing countries. The Intergovernmental Panel on Climate Change (IPCC) methodology is commonly used for estimation of national GHG emission inventories. There is a shortage of on-farm information to evaluate the accuracy of these equations and default emission factors. This work provides valuable information for improving accounting practices within China or for similar manure management practice in other countries.     

Developments in greenhouse gas emissions and net energy use in Danish agriculture - how to achieve substantial CO(2) reductions?

Greenhouse gas (GHG) emissions from agriculture are a significant contributor to total Danish emissions. Consequently, much effort is currently given to the exploration of potential strategies to reduce agricultural emissions. This paper presents results from a study estimating agricultural GHG emissions in the form of methane, nitrous oxide and carbon dioxide (including carbon sources and sinks, and the impact of energy consumption/bioenergy production) from Danish agriculture in the years 1990–2010. An analysis of possible measures to reduce the GHG emissions indicated that a 50–70% reduction of agricultural emissions by 2050 relative to 1990 is achievable, including mitigation measures in relation to the handling of manure and fertilisers, optimization of animal feeding, cropping practices, and land use changes with more organic farming, afforestation and energy crops. In addition, the bioenergy production may be increased significantly without reducing the food production, whereby Danish agriculture could achieve a positive energy balance.     

The impact of municipal solid waste management on greenhouse gas emissions in the United States

Technological advancements, environmental regulations, and emphasis on resource conservation and recovery have greatly reduced the environmental impacts of municipal solid waste (MSW) management, including emissions of greenhouse gases (GHGs). This study was conducted using a life-cycle methodology to track changes in GHG emissions during the past 25 years from the management of MSW in the United States. For the baseline year of 1974, MSW management consisted of limited recycling, combustion without energy recovery, and landfilling without gas collection or control. This was compared with data for 1980, 1990, and 1997, accounting for changes in MSW quantity, composition, management practices, and technology. Over time, the United States has moved toward increased recycling, composting, combustion (with energy recovery) and landfilling with gas recovery, control, and utilization. These changes were accounted for with historical data on MSW composition, quantities, management practices, and technological changes. Included in the analysis were the benefits of materials recycling and energy recovery to the extent that these displace virgin raw materials and fossil fuel electricity production, respectively. Carbon sinks associated with MSW management also were addressed. The results indicate that the MSW management actions taken by U.S. communities have significantly reduced potential GHG emissions despite an almost 2-fold increase in waste generation. GHG emissions from MSW management were estimated to be 36 million metric tons carbon equivalents (MMTCE) in 1974 and 8 MMTCE in 1997. If MSW were being managed today as it was in 1974, GHG emissions would be approximately 60 MMTCE.     

Contribution of milk production to global greenhouse gas emissions

Background, aim and scope  

Studies on the contribution of milk production to global greenhouse gas (GHG) emissions are rare (FAO 2010) and often based on crude data which do not appropriately reflect the heterogeneity of farming systems. This article estimates GHG emissions from milk production in different dairy regions of the world based on a harmonised farm data and assesses the contribution of milk production to global GHG emissions.