皮革废水中CODCr的测定

皮革废水中高浓度的氯化物影响CODCr的测定。经过实验，加入等摩尔的AgNO3，按水样中加入K2Cr2O7溶液与Ag2SO4-H2SO4溶液体积比为30:17，改变酸度，可排除Cl^-干扰，准确测定CODCr的值。     

关于含低CODcr、高CL-稀土废水中CODcr的测定方法探讨

本文通过实验研究，提出用低铬法(0．0250mol/L)测定稀土废水中的CODCr，该方法测定结果和高铬法比较误差较小，准确度提高，并给出了低铬法测定稀土废水中CODCr时，HgSO4最佳使用量。     

基于M-估计测定高氯化工废水CODCr

通过对照试验证明氯气校正可以去除高氯离子对CODCr测定的干扰。事实上,对于特定的高氯废水,实验发现CODCr与实际样品的Cl-含量相关。氯气校正测定的CODCr可用国标方法测定的CODCr和Cl-含量表示。分别以M估计和最小二乘建立了校准方程。进而,实验结果对于存在个别异常值的体系前者相对后者有所改善。     

动态膜压法测定江、污混合水体中有机物含量的探讨

用双驱动动态膜压仪测定江、污混合水中有机物含量。通过测定白龙港污水和长江水混合后的膜压和滞回环面积，用它们与相应的经典法CODCr作图，获得了滞回环面积和CODCr之间良好地线性关系，表明用动态膜压法可快速测定混合水中的有机物含量，不须加任何试剂，不会产生二次污染。同时，对实验结果进行了初步的机理探讨。     

高氯废水COD测定方法的研究

氯离子含量高于1000mg/L时,测定CODCr值较为困难。本文通过实验研究,测定CODCr时掩蔽剂HgSO4掩蔽氯离子的效率,从而获得在测定该类废水CODCr时,HgSO4:Cl-的最佳质量比,对高氯废水COD测定方法的研究具有一定的参考价值。     

混酸介质微波消解快速测定炼油污水COD_(Cr)

针对传统CODCr回流法测定消解时间长、分析费用高等不足,研究了微波消解法在测定炼油污水中CODCr的应用。通过对微波消解功率、消解时间、混酸介质H3PO4H2SO4的用量及体积比等试验,确定了微波消解测定炼油污水CODCr的最佳条件。用该方法对炼油污水各处理装置的出水CODCr进行测定,所得结果与传统的CODCr回流法一致。该方法具有精密度好、分析费用低、消解时间短等优点。     

工业废水中有机污染物指标TOC、CODCr、BOD5相关性研究

研究了工业废水中有机污染物指标TOC、CODCr、BOD5三者之间的相关性。用耶拿Muhiwin N／C 3100型总有机碳测定仪测定TOC,用经典方法测定CODCr、BOD5。通过TOC线性回归计算发现TOC与CODCr、BOD5有很好的相关性。因此对于生产稳定的企业可通过测定TOC推算出CODCr、BOD5值。从而可将TOC作为有机污染物排放控制指标。     

CODCr自动监测仪在污染源监测中的应用

介绍了CODCr在线自动监测仪器的测试原理及功能试验，得出该仪器测量结果与国家标准方法对CODCr的测定无显著差异的结论。     

密封消解法测定高氯离子含盐废水COD_(Cr)的探讨

针对国标重铬酸钾法测定高氯离子含盐废水CODCr时的不足 ,采用密封消解法来测定高盐废水CODCr,通过丁酮氧化率、氯离子干扰、混配水样和实际水样测定结果的比较 ,对国标法和密封消解法进行了验证。试验结果表明 :在测定高氯离子含盐废水CODCr值时 ,密封消解法优于重铬酸钾法 ,能够真实准确地反映废水的CODCr。     

焦化废水中亚硝酸盐和固体悬浮物对CODCr值的影响研究

研究了亚硝酸盐与固体悬浮物对CODCr值的贡献及影响,通过实验找出了在焦化废水中二者与CODCr值的关系,对焦化废水的处理有一定指导意义。     

Effects of humic acid coatings on phenanthrene sorption to black carbon

Black carbon (BC) can strongly adsorb hydrophobic organic compounds (HOCs).The HOC sorption to coated BC could be attenuated in soil and sediment compared with that of the parent BC.To study the potential causes of the sorption attenuation,humic acid (HA) and BC were isolated.Phenanthrene (PHE) was selected as the representative of HOCs.BC was coated with the precipitated HA.The PHE sorption to the HA-coated BC was determined.The HA coatings on BC could result in the significant sorption attenuation of PHE to BC.The attenuation varied in different HA origin and was positively correlated to the aromaticity of HA.The attenuation could be explained by the direct competition between HA and PHE for the available sorption sites on BC and the reduction of the available sorption sites as a result of the pore blockage of BC caused by the HA coatings.Therefore,the HA coatings on BC was one potential cause of the attenuation of HOC sorption to BC in soil and sediment.     

A new photon kinetic-measure based on the kinetics of electron-hole pairs in photodegradation of textile wastewater using the UV-H2O2FS-TiO2 process

Actual textile wastewater and synthesized wastewater containing various textile dyes were photocatalytic degraded by the UVH2O2Fs-TiO2 process in an aimular-flow photocatalytic reactor. In this process, a photon kinetic-measure was adopted to obtain constant rates of dyes decomposition. It was theorized that, by illumination at different UV frequencies, the electrons within the semiconductor were excited from the valence band to the conduction band, yielding the formation of electron-hole pairs which are the pre-requisites for photocatalysis. CPT （critical photonic time） exposure required to cause 90% of vibrations between the double and single bonds along the molecular chain of the dyes to be oxidized, was taken to measure the photocatalytic activities. The CPTs varied with the frequencies of the UV spectral areas. The derivatization of CPT from the first-order kinetic law was presented.     

Single and joint effects of pesticides and mercury on soil urease

The influence of two pesticides including chlorimuron-ethyl and furadan and mercury （Hg） on urease activity in 4 soils （meadow burozem and phaeozem） was investigated. The soils were exposed to various concentrations of the two pesticides and Hg individually and simultaneously. Results showed that there was a close relationship between urease activity and organic matter content in soil. Chlorimuron-ethyl and furadan could both activate urease in the 4 soils. The maximum increment of urease activity by chlorimuronethyl was up to 14%-18%. There was almost an equal increase （up to 13%-21%） in the urease activity by furadan. On the contrary, Hg markedly inhibited soil urease activity. A logarithmic equation was used to describe the relationship （P〈0.05） between the concentration of Hg and the activity of soil urease in the 4 tested soils. Semi-effect dose （ED50） values by the stress of Hg based on the inhibition of soil urease in the 4 soils were 88, 5.5, 24 and 20 mg/kg, respectively, according to the calculation of the corresponding equations. The interactive effect of chlorimuron-ethyl or furadan with metal Hg on soil urease was mainly synergic at the highest tested concentrations.     

Toxic effects of acetochlor, methamidophos and their combination on nifH gene in soil

Toxic effects of two agrochemicals on nifH gene in agricultural black soil were investigated using denaturing gradient gel electrophoresis （DGGE） and sequencing approaches in a microcosm experiment. Changes of soil nifH gene diversity and composition were examined following the application of acetochlor, methamidophos and their combination. Acetochlor reduced the nifH gene diversity （both in gene richness and diversity index values） and caused changes in the nifH gene composition. The effects of acetochlor on nifH gene were strengthened as the concentration of acetochlor increased. Cluster analysis of DGGE banding patterns showed that nifH gene composition which had been affected by low concentration of acetochlor （50 mg/kg） recovered firstly. Methamidophos reduced nifH gene richness that except at 4 weeks. The medium concentration of methamidophos （150 mg/kg） caused the most apparent changes in nifH gene diversity at the first week while the high concentration of methamidophos （250 mg/kg） produced prominent effects on nifH gene diversity in the following weeks. Cluster analysis showed that minimal changes of nifH gene composition were found at 1 week and maximal changes at 4 weeks. Toxic effects of acetochlor and methamidophos combination on nifH gene were also apparent. Different nifH genes （bands） responded differently to the impact of agrochemicals： four individual bands were eliminated by the application of the agrochemicals, five bands became predominant by the stimulation of the agrochemicals, and four bands showed strong resistance to the influence of the agrochemicals. Fifteen prominent bands were partially sequenced, yielding 15 different nifH sequences, which were used for phylogenetic reconstructions. All sequences were affiliated with the alpha- and beta-proteobacteria, showing higher similarity to eight different diazotrophic genera.     

Potential of plant polyphenol oxidases in the decolorization and removal of textile and non-textile dyes

In this study an effort has been made to use plant polyphenol oxidases; potato （Solanum tuberosum） and brinjal （Solanum melongena）, for the treatment of various important dyes used in textile and other industries. The ammonium sulphate fractionated enzyme preparations were used to treat a number of dyes under various experimental conditions. Majority of the treated dyes were maximally decolorized at pH 3.0. Some of the dyes were quickly decolorized whereas others were marginally decolorized. The initial first hour was sufficient for the maximum decolorization of dyes. The rate of decolorization was quite slow on long treatment of dyes. Enhancement in the dye decolorization was noticed on increasing the concentration of enzymes. The complex mixtures of dyes were treated with both preparations of polyphenol oxidases in the buffers of varying pH values. Potato polyphenol oxidase was significantly more effective in decolorizing the dyes to higher extent as compared to the enzyme obtained from brinjal polyphenol oxidase. Decolorization of dyes and their mixtures, followed by the formation of an insoluble precipitate, which could be easily removed simply by centrifugation.     

Isolation and algae-lysing characteristics of the algicidal bacterium B5

Water blooms have become a worldwide environmental problem.Recently,algicidal bacteria have attracted wide attention as possible agents for inhibiting algal water blooms.In this study,one strain of algicidal bacterium B5 was isolated from activated sludge.On the basis of analysis of its physiological characteristics and 16S rDNA gene sequence,it was identified as Bacillusfusiformis.Its algae- lysing characteristics on Microcystis aeruginosa,Chlorella and Scenedesmus were tested.The results showed that:(1)the algicidal bacterium B5 is a Gram-negative bacterium.The 16S rDNA nucleotide sequence homology of strain B5 with 2 strains of B.fusiformis reached 99.86%,so B5 was identified as B.fusiformis;(2)the algal-lysing effects of the algicidal bacterium B5 on M.aeruginosa, Chlorella and Scenedesmus were pronounced.The initial bacterial and algal cell densities strongly influence the removal rates of chlorophyll-α.The greater the initial bacterial cell density,the faster the degradation of chlorophyll-α.The greater the initial algal cell density,the slower the degradation of chlorophyll-α.When the bacterial cell density was 3.6 x l07 cells/ml,nearly 90% of chlorophyll-αwas removed.When the chlorophyll-αconcentration was less than 550μg/L,about 70% was removed;(3)the strain B5 lysed algae by secreting metabolites and these metabolites could bear heat treatment.     

Emissions of SO2, NO and N2O in a circulating fluidized bed combustor during co-firing coal and biomass

This paper presents the experimental investigations of the emissions of SO2, NO and N2O in a bench scale circulating fluidized bed combustor for coal combustion and co-firing coal and biomass. The thermal capacity of the combustor is 30 kW. The setup is electrically heated during startup. The influence of the excess air, the degree of the air staging, the biomass share and the feeding position of the fuels on the emissions of SO2, NO and N2O were studied. The results showed that an increase in the biomass shares resulted in an increase of the CO concentration in the flue gas, probably due to the high volatile content of the biomass. In co-firing, the emission of SO2 increased with increasing biomass share slightly, however, non-linear increase relationship between SO2 emission and fuel sulfur content was observed. Air staging significantly decreased the NO emission without raising the SO2 level. Although the change of the fuel feeding position from riser to downer resulted in a decrease in the NO emission level, no obvious change was observed for the SO2 level. Taking the coal feeding position R as a reference, the relative NO emission could significantly decrease during co-firing coal and biomass when feeding fuel at position D and keeping the first stage stoichiometry greater than 0.95. The possible mechanisms of the sulfur and nitrogen chemistry at these conditions were discussed and the ways of simultaneous reduction of SO2, NO and N2O were proposed.     

Adsorption thermodynamics and kinetic investigation of aromatic amphoteric compounds onto different polymeric adsorbents

The adsorption behavior of p-aminobenzoic acid and o-aminobenzoic acid onto the different polymeric adsorbents was systematically investigated as a function of the solution concentration and temperature.Experimental results indicated that the equilibrium adsorption data of the four polymeric adsorbents fitted well in the Freundlich isotherm.The adsorption capacity of multi-functional polymeric adsorbent NJ-99 was the highest,which might be attributed to the strong hydrogen-bonding interaction between the amino groups on the resin and the carboxyl group of aminobenzoic acid.The adsorption capacity of o-aminobenzoic acid onto any adsorbent was higher than p-aminobenzoic acid.Thermodynamic studies suggested the exothermic,spontaneous physical adsorption process.Adsorption kinetics results showed that the adsorption followed the pseudo-second-order kinetics model and the intraparticle mass transfer process was the rate-controlling step.     

Formation of multiple trimethylsilyl derivatives in the derivatization of 17α-ethinylestradiol with BSTFA or MSTFA followed by gas chromatography-mass spectrometry determination

N,O-bis(trimethylsily)trifluoroacetamide (BSTFA) and N-methyl-N(trimethylsily) trifluoroacetamide (MSTFA) are common derivatization reagents used in the GC-MS analysis of estrogen steroids such as estrone (E1) and 17(-ethinylestradiol (EE2). In this study, three trimethylsilyl (TMS) steroid derivatives, mono-and di-trimethylsilyl EE2 and mono-trimethylsilyl E1, were observed during the derivatization of EE2 with BSTFA or MSTFA and/or GC separation. Factors influencing the production of multiple TMS derivatives and their relative abundance were examined. It was found that both methanol and bisphenol A competed with estrogenic esteroids when reacting with silylation reagents, and thus affected the formation of TMS derivatives and their relative abundance in the derivatization products. Methanol was found to be more reactive than bisphenol A with the BSTFA reagent. None of the three solvents tested in this study could prevent the generation of multiple TMS derivatives during the derivatization of EE2 with BSTFA, followed by GC analysis. A similar result was observed using MSTFA as the derivative reagent followed by GC analysis. Thus, the suitability of BSTFA or MSTFA as the derivatization reagent for the determination of E1 and EE2 by GC-MS, under the conditions reported here, is questionable. This problem can be solved by adding trimethylsilylimidaz (TMSI) in the BSTFA reagent as recommended, and the performance of the method has been proved in this study.     

Treated wastewater irrigation effect on soil, crop and environment： Wastewater recycling in the loess area of China

A study was carried out at the Loess Plateau in Dongzhi,China,to test the feasibility of using secondary treatment sewage effluent and to determine whether the water quality would then meet the recommended irrigation norm.Seven crops,including celery,wheat, maize,millet,apples,rapeseed and yellow beans,were tested in the study.Physical and chemical properties of the soil,crop yield and quality and leachate at different soil depths were measured.In most cases,the quality of the crops that made use of treated sewage was not distinctively different from those that did not use treated sewage.However,yields for the former were much higher than they were for the latter.Leachates at different soil depths were analyzed and the results did not show alarming levels of constituents.For a period of approximately 14 months,the treated sewage irrigation had no significant effect on the loess soil and no cases of illness resulting from contact with the treated sewage were reported.With treated sewage irrigation,a slight increase in the organic content of the soil was observed.