Hydraulic constraints on the performance of a groundwater denitrification wall for nitrate removal from shallow groundwater

Denitrification walls are a practical approach for decreasing non-point source pollution of surface waters. They are constructed by digging a trench perpendicular to groundwater flow and mixing the aquifer material with organic matter, such as sawdust, which acts as a carbon source to stimulate denitrification. For efficient functioning, walls need to be permeable to groundwater flow. We examined the functioning of a denitrification wall constructed in an aquifer consisting of coarse sands. Wells were monitored for changes in nitrate concentration as groundwater passed through the wall and soil samples were taken to measure microbial parameters inside the wall. Nitrate concentrations upstream of the wall ranged from 21 to 39 g N m(-3), in the wall from 0 to 2 g N m(-3) and downstream from 19 to 44 g N m(-3). An initial groundwater flow investigation using a salt tracer dilution technique showed that the flow through the wall was less than 4% of the flow occurring in the aquifer. Natural gradient tracer tests using bromide and Rhodamine-WT confirmed groundwater bypass under the wall. Hydraulic conductivity of 0.48 m day(-1) was measured inside the wall, whereas the surrounding aquifer had a hydraulic conductivity of 65.4 m day(-1). This indicated that during construction of the wall, hydraulic conductivity of the aquifer had been greatly reduced, so that most of the groundwater flowed under rather than through the wall. Denitrification rates measured in the center of the wall ranged from 0.020 to 0.13 g N m(-3) day(-1), which did not account for the rates of nitrate removal (0.16-0.29 g N m(-3) day(-1)) calculated from monitoring of groundwater nitrate concentrations. This suggested that the rate of denitrification was greater at the upstream face of the wall than in its center where it was limited by low nitrate concentrations. While denitrification walls can be an inexpensive tool for removing nitrate from groundwater, they may not be suitable in aquifers with coarse textured subsoils where simple inexpensive construction techniques result in major decreases in hydraulic conductivity.     

A comparison of organic and inorganic carbon controls over biological denitrification in aquaria

In aquaria and rearing tanks, nitrate accumulation as a result of organic matter degradation is inevitable and has two major negative side effects: direct toxicity to organisms, specially invertebrates, and the introduction of a reducing environment by oxygen consumption. The aim of this study was to compare two alternate methods of removing nitrogen compounds from closed systems, autotrophic columnar denitrification (ACD) and heterotrophic columnar denitrification (HCD) by following end product concentrations as reaction progressed. A pilot plant consisting of two series of 50 dm3 recirculating flow systems (each in triplicate) was used to test both methods. Absence of pH control was also useful in autotrophic denitrification systems in order to follow effects over reaction rates and pathways. Concentrations of NO(3-), NO2- and NH(4+) were followed throughout the experiment, as well as pH, temperature and salinity. Under different flow conditions results show that higher nitrate reduction rates were possible in the autotrophic systems (35.1+/-4.7 microM/day without pH control until reversal of the process and 20.6+/-7.3 microM/day after reestablishment of pH control) in comparison with heterotrophic (9.9+/-1.3 microM/day). However, pH control through calcium bicarbonate addition was found to be crucial in maintaining constant levels of total denitrification in ACD systems, just as it was necessary to closely maintain organic carbon addition to HCD systems.     

Evaluating non-equilibrium solute transport in small soil columns

Displacement studies on leaching of bromide and two pesticides (atrazine and isoproturon) were conducted under unsaturated steady state flow conditions in 24 small undisturbed soil columns (5.7 cm in diameter and 10 cm long) each collected from two sites differing in soil structure and organic carbon content in North Germany. There were large and irregular variabilities in the characteristics of both soils, as well as in the shapes of breakthrough curves (BTCs) of different columns, including some with early breakthrough and increased tailing, qualitatively indicating the presence of preferential flow. It was estimated that one preferential flow column (PFC) at site A, and four at site B, contributed, respectively to 11% and 58% of the accumulated leached fraction and to more than 80% of the maximum observed standard deviation (SD) in the field-scale concentration and mass flux of pesticides at two sites. The bromide BTCs of two sites were analyzed with the equilibrium convection-dispersion equation (CDE) and a non-equilibrium two-region/mobile-immobile model. Transport parameters of these models for individual BTCs were determined using a curve fitting program, CXTFIT, and by the time moment method. For the CDE based equilibrium model, the mean values of retardation factor, R, considered separately for all columns, PFCs or non-preferential flow columns (NPFCs) were comparable for the two methods; significant differences were observed in the values of dispersion coefficients of two sites using the two estimation methods. It was inferred from the estimated parameters of non-equilibrium model that 5-12% of water at site A, and 12% at site B, was immobile during displacement in NPFCs. The corresponding values for PFCs of two sites were much larger, ranging from 25% to 51% by CXTFIT and from 24% to 72% by the moment method, suggesting the role of certain mechanisms other than immobile water in higher degrees of non-equilibrium in these columns. Peclet numbers in PFCs of both sites were consistently smaller than five, indicating the inadequacy of the non-equilibrium model to incorporate the effect of all forms of non-equilibrium in PFCs. Overall, the BTCs of individual NPFCs, PFCs and of field average concentration at the two sites were better reproduced with parameters obtained from CXTFIT than by the moment method. The moment method failed to capture the peak concentrations in PFCs, but tended to describe the desorption and tail branches of BTCs better than the curve fitting approach.     

Removal of added nitrate in the single, binary, and ternary systems of cotton burr compost, zerovalent iron, and sediment: Implications for groundwater nitrate remediation using permeable reactive barriers

Recent research has shown that carbonaceous solid materials and zerovalent iron (Fe(0)) may potentially be used as media in permeable reactive barriers (PRBs) to degrade groundwater nitrate via heterotrophic denitrification in the solid carbon system, and via abiotic reduction and autotrophic denitrification in the Fe(0) system. Questions arise as whether the more expensive Fe(0) is more effective than the less expensive carbonaceous solid materials for groundwater nitrate remediation, and whether there is any synergistic effect of mixing the two different types of materials. We carried out batch tests to study the nature and rates of removal of added nitrate in the suspensions of single, binary, and ternary systems of cotton burr compost, Peerless Fe(0), and a sediment low in organic carbon. Cotton burr compost acted as both organic carbon source and supporting material for the growth of indigenous denitrifiers. Batch tests showed that cotton burr compost alone removed added nitrate at a greater rate than did Peerless Fe(0) alone on an equal mass basis with a pseudo-first-order rate constant k=0.0830+/-0.0031 h(-1) for cotton burr compost and a k=0.00223+/-0.00022 h(-1) for Peerless Fe(0); cotton burr compost also removed added nitrate at a faster rate than did cotton burr compost mixed with Peerless Fe(0) and/or the sediment. Furthermore, there was no substantial accumulation of ammonium ions in the cotton burr compost system, in contrast to the systems containing Peerless Fe(0) in which ammonium ions persisted as major products of nitrate reduction. It is concluded that cotton burr compost alone may be used as an excellent denitrification medium in a PRB for groundwater nitrate removal. Further study is needed to evaluate performance of its field applications.     

Microbial reduction of nitrate in the presence of nanoscale zero-valent iron

Microbial reduction of nitrate in the presence of nanoscale zero-valent iron (NZVI) was evaluated to assess the feasibility of employing NZVI in the biological nitrate treatment. Nitrate was completely reduced within 3 d in a nanoscale Fe(0)-cell reactor, while only 50% of the nitrate was abiotically reduced over 7 d at 25 °C. The removal rate of nitrate in the integrated NZVI-cell system was unaffected by the presence of high amounts of sulfate. Efficient removal of nitrate by Fe(II)-supported anaerobic culture in 14 d indicated that Fe(II), which is produced during anaerobic iron corrosion in the Fe(0)-cell system, might act as an electron donor for nitrate. Unlike abiotic reduction, microbial reduction of nitrate was not significantly affected by low temperature conditions. This study demonstrated the potential applicability of employing NZVI iron as a source of electrons for biological nitrate reduction. Use of NZVI for microbial nitrate reduction can obviate the disadvantages associated with traditional biological denitrification, that relies on the use of organic substrates or explosive hydrogen gas, and maintain the advantages offered by nano-particle technology such as higher surface reactivity and functionality in suspensions.     

Denitrification in cypress swamp within the Atchafalaya River Basin, Louisiana

Nitrogen has been implicated as a major cause of hypoxia in shallow water along the Louisiana/Texas, USA coasts. Excess nitrogen (mainly nitrate) from Mississippi and Atchafalaya River drainage basins may drive the onset and duration of hypoxia in the northern Gulf of Mexico. Restoring and enhancing denitrification have been proposed to reduce and control coastal hypoxia and improve water quality in the Mississippi River Basin. Sediments were collected from six baldcypress restoration sites within the Atchafalaya River Basin, Louisiana, USA. The acetylene blockage technique was used to measure background and potential sediment denitrification rates. Denitrification fluxes were measured before nitrate addition (background rates) and after nitrate addition of 100mgNl(-1) (potential denitrification) at three seasonal temperatures. Background denitrification was low across all cypress swamp sites ranging from 0.9 to 8.8, 0.6 to 28.5 and 8.8 to 47.5g N evolved ha(-1)d(-1) at water/sediment column temperatures of 8, 22 and 30 degrees C, respectively. After nitrate addition, temperature had a significant effect on sediment denitrification potential. Maximum rates measured at 8, 22 and 30 degrees C were approximately 250-260, 550 and 970gNha(-1)d(-1), respectively. Most of the added nitrate in water columns, incubated at 8 degrees C, was removed after 65d compared to 32d and 17d at 22 and 30 degrees C, respectively. These results indicate cypress swamps have the potential to assimilate and process elevated levels of floodwater nitrate with denitrification being a major removal mechanism.     

Numerical simulation of a fine-grained denitrification layer for removing septic system nitrate from shallow groundwater

One of the most common methods to dispose of domestic wastewater involves the release of septic effluent from drains located in the unsaturated zone. Nitrogen from such systems is currently of concern because of nitrate contamination of drinking water supplies and eutrophication of coastal waters. It has been proposed that adding labile carbon sources to septic distribution fields could enhance heterotrophic denitrification and thus reduce nitrate concentrations in shallow groundwater. In this study, a numerical model which solves for variably saturated flow and reactive transport of multiple species is employed to investigate the performance of a drain field design that incorporates a fine-grained denitrification layer. The hydrogeological scenario simulated is an unconfined sand aquifer. The model results suggest that the denitrification layer, supplemented with labile organic carbon, may be an effective means to eliminate nitrogen loading to shallow groundwater. It is also shown that in noncalcareous aquifers, the denitrification reaction may provide sufficient buffering capacity to maintain near neutral pH conditions beneath and down gradient of the drain field. Leaching of excess dissolved organic carbon (DOC) from the denitrification layer is problematic, and causes an anaerobic plume to develop in simulations where the water table is less than 5-6 m below ground surface; this anaerobic plume may lead to other down gradient changes in groundwater quality. A drain field and denitrification layer of smaller dimensions is shown to be just as effective for reducing nitrate, but has the benefit of reducing the excess DOC leached from the layer. This configuration will minimize the impact of wastewater disposal in areas where the water table is as shallow as 3.5 m.     

The addition of organic carbon and nitrate affects reactive transport of heavy metals in sandy aquifers

Organic carbon introduction in the soil to initiate remedial measures, nitrate infiltration due to agricultural practices or sulphate intrusion owing to industrial usage can influence the redox conditions and pH, thus affecting the mobility of heavy metals in soil and groundwater. This study reports the fate of Zn and Cd in sandy aquifers under a variety of plausible in-situ redox conditions that were induced by introduction of carbon and various electron acceptors in column experiments. Up to 100% Zn and Cd removal (from the liquid phase) was observed in all the four columns, however the mechanisms were different. Metal removal in column K1 (containing sulphate), was attributed to biological sulphate reduction and subsequent metal precipitation (as sulphides). In the presence of both nitrate and sulphate (K2), the former dominated the process, precipitating the heavy metals as hydroxides and/or carbonates. In the presence of sulphate, nitrate and supplemental iron (Fe(OH)(3)) (K3), metal removal was also due to precipitation as hydroxides and/or carbonates. In abiotic column, K4, (with supplemental iron (Fe(OH)(3)), but no nitrate), cation exchange with soil led to metal removal. The results obtained were modeled using the reactive transport model PHREEQC-2 to elucidate governing processes and to evaluate scenarios of organic carbon, sulphate and nitrate inputs.     

Nitrate distribution and denitrification in the saturated zone of paddy field under rice/wheat rotation

Nitrate concentration in well water collected from the wells near farm houses was investigated in the Taihu Lake basin (TBL) of China. Nitrate-N content of the well water ranged from 0.1 to 23 mgNl(-1), and 41% exceeded the criteria (10 mg Nl(-1)). It was found that the difference in well conditions, especially the depth of the well, was the main cause of the difference in the nitrate concentration of well water, i.e. it was higher in shallow well and lower in deeper well. A recommendation was made for local farmers to drill wells deeper than 10 m in order to reduce the risk of high ingestion of nitrate-N in their drinking water. Nitrate distribution and denitrification in the saturated zone of a paddy field under rice/wheat rotation in the TBL were studied. Porous pipes were installed in triplicate at depths of 1.5, 2.0, 2.5, 3.5 and 5 m respectively to collect the soil solution samples. Results showed that nitrate was the predominant N form in soil solution of saturated zone, and it increased from 1.5 to 2.5 m depth, and decreased from 2.5 to 5 m depth. N2O captured in the soil solution was very high comparing with N2O content in air. N2O content was positively correlated with nitrate concentrations in the soil profile. These results indicate that nitrate leached into saturated zone was mainly transformed via denitrification processes. Comparing the sum of inorganic nitrogen with the total nitrogen in soil solution samples collected from those wells at the field, some soluble organic nitrogen was found about 1-2 mg N l(-1) in average.     

Calibration and validation of an integrated nitrate transport model within a well capture zone

Groundwater contamination by nitrate was investigated in an agricultural area in southern Quebec, Canada, where a municipal well is the local source of drinking water. A network of 38 piezometers was installed within the capture zone of the municipal well to monitor water table levels and nitrate concentrations in the aquifer. Nitrate concentrations were also measured in the municipal well. A Water flow and Nitrate transport Global Model (WNGM) was developed to simulate the impact of agricultural activities on nitrate concentrations in both the aquifer and municipal well. The WNGM first uses the Agriflux model to simulate vertical water and nitrate fluxes below the root zone for each of the seventy agricultural fields located within the capture zone of the municipal well. The WNGM then uses the HydroGeoSphere model to simulate three-dimensional variably-saturated groundwater flow and nitrate transport in the aquifer using water and nitrate fluxes computed with the Agriflux model as the top boundary conditions. The WNGM model was calibrated by reproducing water levels measured from 2005 to 2007 in the network of piezometers and nitrate concentrations measured in the municipal well from 1997 to 2007. The nitrate concentrations measured in the network of piezometers, however, showed greater variability than in the municipal well and could not be reproduced by the calibrated model. After calibration, the model was validated by successfully reproducing the decrease of nitrate concentrations observed in the municipal well in 2006 and 2007. Although it cannot predict nitrate concentrations in individual piezometers, the calibrated and validated WNGM can be used to assess the impact of changes in agricultural practices on global nitrate concentrations in the aquifer and in the municipal well.     

Application of plant carbon source for denitrification by constructed wetland and bioreactor: review of recent development

Water quality standard for nitrate becomes more and more strict, and the plant carbon source is widely used for denitrification by constructed wetland (CW) and bioreactor. However, the nitrate removal efficiency by different types of plant carbon source are not evaluated comprehensively. Denitrification performance of different plant carbon sources, and the influence of dosing method and pretreatment are thoroughly reviewed in this paper, which aims to investigate the accurate utilization of plant carbon source for nitrogen (as nitrate) removal. It is concluded that plant carbon source addition for all types of CWs and bioreactors can improve the nitrate removal efficiency to some extent, and the dosing method of plant carbon source for denitrification should be further studied and optimized in the future. The popular carbon sources for CW and bioreactor denitrification enhancement are woodchip, chopped macrophytes, crop plants, macrophytes litters, etc. The recommended optimum C:N ratios for CW and bioreactor are 4.0:5.0 and 1.8:3.0, respectively. The physical and biological pretreatments are selected to supply organic carbon for long-term denitrification.     

Transport characteristics of gas phase ozone in unsaturated porous media for in-situ chemical oxidation

Encapsulation technology is being investigated as a method for controlling pH in situ at contaminated groundwater sites where pH may limit remediation of organic contaminants. This study examined the effectiveness of using KH2PO4 buffer encapsulated in a pH-sensitive coating to neutralize pH in laboratory sand columns (1.5-1) under a simulated groundwater flow rate and characterized the pattern of capsule release in the flow-through system. Denitrification was used in the columns to increase the pH of the pore water. Each of three columns was equipped with three miniature mesh wells to allow contact of the buffer with column pore water, but capsules (15 g) were inserted into only one column (amended). The two other columns served as amendment (no buffer) and abiotic (no denitrification) controls. Oxidation-reduction potential, dissolved organic and inorganic carbon, NH4+, NO3- +NO2-, PO(4)3-, and pH were measured in the influent, two side ports, and effluent of the columns over time. Near complete conversion of 80 mg N/1 of nitrate and 152 mg/l of ethanol per day resulted in a mean pH increase from 6.2 to 8.2 in the amendment control column. The amended column maintained the target pH of 7.0 +/- 0.2 for 4 weeks until the capsules began to be depleted, after which time the pH slowly started to increase. The capsules exhibited pulses of buffer release, and were effectively dissolved after 7.5 weeks of operation. Base-neutralizing capacity contributed by the encapsulated buffer over the entire study period, calculated as cation equivalents, was 120 mM compared to 8 mM without buffer. This study demonstrates the potential for this technology to mediate pH changes and provides the framework for future studies in the laboratory and in the field, in which pH is controlled in order to enhance organic contaminant remediation by pH-sensitive systems.     

Colloid‐facilitated transport of metolachlor through intact soil columns

Abstract

This study evaluated the role of water dispersible colloids with diverse physicochemical and mineralogical characteristics in facilitating the transport of metolachlor through macropores of intact soil columns. The soil columns represented upper solum horizons of an Alfisol in the Bluegrass region of Kentucky. Three different colloid suspensions tagged with metolachlor [2‐chloro‐N‐(2‐ethyl‐6‐methylphenyl)‐N‐(2‐methoxy‐l‐methylethyl)acetamide] were introduced at a constant flux into undisturbed soil columns. The eluents were collected and analyzed periodically for colloid and metolachlor concentrations. Colloid recovery in the eluents ranged from 54 to 90 %. The presence of colloids enhanced the transport of metolachlor by 22 to 70 % depending on the colloid type and mobility. Colloids with higher pH, organic carbon, cation exchange capacity (CEC), total exchangeable bases (TEB), surface area (SA), and electrophoretic mobility (EM), showed better mobility, greater affinity for interaction with the herbicide and, thus, greater potential to co‐transport metolachlor. In contrast, increased level of kaolinite, Fe, and Al inhibited metolachlor adsorption and transport. In spite of the increased transportability of metolachlor by the presence of soil colloids, the colloid bound herbicide portion accounted for a very small part of the observed increase. This suggests that surface site exclusion mechanisms and preferential sorption induced by the presence of colloids are more important than ion exchange phenomena in promoting herbicide mobility in subsurface environments.     

Laboratory and field evaluation of instrumentation for the semicontinuous determination of particulate nitrate (and other water-soluble particulate components)

Studies conducted at the U.S. Environmental Protection Agency facility in Research Triangle Park, NC, and at a field study in Southern California have demonstrated the capability for the semicontinuous determination of particulate nitrate (and other water-soluble ionic species). Two instruments, an R&P Series 8400N Ambient Particulate Nitrate Monitor (8400N) and an ion chromatography (IC)-based prototype monitor developed at Texas Tech University, were evaluated both in the laboratory using aqueous standards and simulated ambient aerosols and in the field during a 3-week July 1-21, 2003) joint ambient comparison study with Brigham Young University and the South Coast Air Quality Management District (SCAQMD). The field study was conducted at the SCAQMD Rubidoux field site near Riverside, CA. During initial (before the field study) laboratory studies, both instruments were responsive to changes in the simulated aerosol concentration. However, potential problems were discovered involving both instruments during the laboratory-based studies both before and after the Rubidoux study, and these problems are currently being addressed. During the 3-week field study period, 15-minute average particulate nitrate concentrations approaching 30 microg/m3 were observed. Because of malfunctioning IC components (concentrator columns) of the Texas Tech University prototype monitor, limited data were obtained from this instrument during the 3-week sampling period. Initial ambient comparisons show general agreement between the 8400N and IC-based prototype instrument for the semicontinuous determination of ambient particulate nitrate at lower nitrate concentrations (<15 microg/m3) and an underdetermination by the 8400N at higher concentrations (>15 microg/m3). A decreased molybdenum converter efficiency in the pulse analyzer of the 8400N discovered during postfield study laboratory evaluation may explain the negative bias observed at higher nitrate concentrations. Semicontinuous results obtained from U.S. Environmental Protection Agency-operated instruments were averaged and compared with integrated sampler results obtained by Brigham Young University and SCAQMD.     

饮用水中硝酸盐的脱除

饮用水中硝酸盐氮的污染问题日趋严重,对人类的健康有多方面的危害.离子交换、反渗透、电渗、生物反硝化、化学和化学催化反硝化都可从水中脱除硝酸盐,但目前投入实用的只有离子交换、生物反硝化、反渗透三种工艺.这些脱硝方法各有优缺点.本文综述了饮用水脱硝的应用与研究的现状,并对其发展的趋势进行了简单的论述.     

Comparison of biotic and abiotic treatment approaches for co-mingled perchlorate, nitrate, and nitramine explosives in groundwater

Biological and abiotic approaches for treating co-mingled perchlorate, nitrate, and nitramine explosives in groundwater were compared in microcosm and column studies. In microcosms, microscale zero-valent iron (mZVI), nanoscale zero-valent iron (nZVI), and nickel catalyzed the reduction of RDX and HMX from initial concentrations of 9 and 1 mg/L, respectively, to below detection (0.02 mg/L), within 2 h. The mZVI and nZVI also degraded nitrate (3 mg/L) to below 0.4 mg/L, but none of the metal catalysts were observed to appreciably reduce perchlorate ( approximately 5 mg/L) in microcosms. Perchlorate losses were observed after approximately 2 months in columns of aquifer solids treated with mZVI, but this decline appears to be the result of biodegradation rather than abiotic reduction. An emulsified vegetable oil substrate was observed to effectively promote the biological reduction of nitrate, RDX and perchlorate in microcosms, and all four target contaminants in the flow-through columns. Nitrate and perchlorate were biodegraded most rapidly, followed by RDX and then HMX, although the rates of biological reduction for the nitramine explosives were appreciably slower than observed for mZVI or nickel. A model was developed to compare contaminant degradation mechanisms and rates between the biotic and abiotic treatments.     

Arsenic speciation and accumulation in evapoconcentrating waters of agricultural evaporation basins

To sustain agricultural productivity, evaporation basins (or ponds) have been widely used for the disposal of agricultural drainage in areas requiring subsurface drainage in the San Joaquin Valley of California, USA. The drainage water contains elevated concentration of trace elements including selenium (Se) and arsenic (As). Unlike Se, little information is available about As, a potentially high risk element. The objective of this study was to characterize the chemical behavior of As and acquire data for better understanding of biogeochemical processes and conditions affecting As fate in evaporation ponds. The study site was a 726 ha evaporation basin facility (containing 10 cells with water flowing in series) in the hydrologically closed Tulare Basin of California. We examined water chemistry, As concentration and speciation along the water flow path between cells as well as within the cells. Arsenic concentrations in the water increased linearly with Cl(-), a conservative ion from evapoconcentration. Reduced As species as arsenite [As(III)] and organic arsenic (org-As) also increased with increases in Cl(-) and salinity. Water samples with elevated EC (i.e., towards the end of flow path) had high dissolved organic matter, low dissolved oxygen, and elevated sulfide concentrations, indicating the development of reducing conditions. We hypothesize that such changes could facilitate the reduction of arsenate [As(V)] to As(III) and org-As. Elevated As in sediment profiles indicate a solid phase sink mechanism, but not significant enough to remove and reduce As concentrations in the water columns. These findings help us better define the processes that affect As in drainage facilities and contribute to our understanding of how As behaves in other regions of the world that have similar climatic and hydrogeochemical conditions.     

Assessment of denitrification process in lower Ishikari river system,Japan

Sediment denitrification rate and its role in removal of dissolved nitrate load in lower Ishikari river system were examined. Denitrification rate were measured using acetylene inhibition technique on the sediment samples collected during August 2009–July 2010. The denitrification rate varied from 0.001 to 1.9 μg N g⁻¹ DM h⁻¹ with an average value of 0.21 μg N g⁻¹ DM h⁻¹ in lower Ishikari river system. Denitrification rate showed positive correlation with dissolved nitrate concentration in the river basin, indicating overlying water column supplied nitrate for the sediment denitrification processes. Nutrient enrichment experiments result showed that denitrification rate increased significantly with addition of nitrate in case of samples collected from Barato Lake however no such increase was observed in the samples collected from Ishikari river main channel and its major tributaries indicating that factors other than substrate concentration such as population of denitrifier and hydrological properties of stream channel including channel depth and flow velocity may affects the denitrification rate in lower Ishikari river system. Denitrification rate showed no significant increase with the addition of labile carbon (glucose), indicating that sediment samples had sufficient organic matter to sustain denitrification activity. The result of nutrient spiraling model indicates that in- stream denitrification process removes on an average 5% d⁻¹ of dissolve nitrate load in Ishikari river. This study was carried out to fill the gap present in the availability of riverine denitrification rate measurement and its role in nitrogen budget from Japanese rivers characterize by small river length and high flow rate.     

湖岸缓冲带反硝化作用的研究进展

反硝化作用是湖岸缓冲带去除硝酸盐的重要途径。湖岸缓冲带是联系陆地与湖泊生态系的纽带,不仅为许多动植物提供适宜生境,而且通过反硝化作用能去除地下水中的硝酸盐,提高湖泊水质。概述不同检测反硝化速率的方法,并对比各种方法的优点与缺点。阐述反硝化作用的影响因素：厌氧环境、有机碳、湖岸坡度、缓冲带坡度、pH与温度、硝酸盐浓度。介绍反硝化速率模型的研究开发状况。最后,提出了目前国内外反硝化研究中存在的不足及发展方向。     

Field test of a cross-injection scheme for stimulating in situ denitrification near a municipal water supply well

A pilot-scale test of an in situ denitrification scheme was undertaken to assess an adaptation of the nutrient injection wall (NIW) technology for treating a deep (30-40 m) nitrate contamination problem (N-NO(-)(3) ~ 10-12 mg/L). The adaptation is called the Cross-Injection Scheme (CIS). It duplicates the NIW method without a wall; wells are installed and operated directly in the aquifer and high-flux zones of the aquifer are preferentially targeted for treatment. The test was conducted on the site of a municipal water supply well field, with the supply well pumping between 15-80 m(3)/h. Acetate was periodically injected into the aquifer between an injection-extraction well pair positioned across the normal direction of flow. The injected pulses were then permitted to move with the water toward the municipal wells, providing a carbon supply to drive the desired denitrification. The fate of nitrate, nitrite, acetate and sulphate were monitored at multilevel wells located between the injection location and the municipal wells. The acetate pulsing interval was approximately weekly (9 h injections), so that the system was operating passively 95% of the time. Previous work on the site has established that the highest solute fluxes were associated with a 1-3 m thick zone about 35 m below surface. This zone was found to respond to the acetate additions as a function of the municipal pumping rate and the carbon-to-nitrogen ratio (i.e., determined by the injected acetate concentration). Initially, acetate was injected just below the theoretical stoichiometric requirement for complete denitrification and nitrate disappearance was accompanied by nitrite production. Increasing the C:N ratio (doubling the acetate injection concentration) increased the removal of nitrate and diminished the occurrence of nitrite. Slowing the municipal pumping rate, with a C:N ratio of 1.2-1.6, resulted in complete nitrate attenuation with no nitrite production and no sulfate reduction. The experiment demonstrated that the CIS injection scheme is a viable option for the treatment of nitrate contamination in situ near high-capacity wells.