铁炭微电解/Fenton试剂预处理土霉素废水的研究

研究了铁炭微电解/Fenton试剂法工艺对高浓度难生化处理的土霉素废水预处理效果.结果表明,当原水COD在6 000 mg/L、pH值为2.2时,铁炭微电解反应时间为80 min,铁炭微电解对原水COD的去除率>40%;铁炭微电解出水再投加220 mg/L的H2O2(30%)进行Fenton试剂法处理,常温下反应50 min对原水COD的去除率可提高到75%以上.铁炭微电解 Fenton试剂联合工艺的处理效果好、运行稳定、成本低廉,适宜对难降解的土霉素废水的预处理.     

Fenton试剂法预处理发酵甘油生产提取废水

采用Fenton试剂预处理高浓度难降解发酵法甘油生产提取废水。研究了pH、Fe2 + 、H2 O2 、反应时间和H2 O2 投加次数对废水COD去除效果的影响。结果表明 ,通过Fenton试剂氧化可使废水中的COD值从 135 0 0mg/L降至 4 0 30mg/L ,COD去除率达到 70 1%。废水的BOD5/COD值从 0 2 0 2提高至 0 5 6 8,可生化性得到较大提高 ,为后续处理创造了条件。研究成果为发酵法甘油生产提取废水的预处理提供了一种非常有效的方法。     

Fenton试剂法预处理发酵甘油生产提取废水

采用Fenton试剂预处理高浓度难降解发酵法甘油生产提取废水。研究了pH、Fe^2 、H2O2、反应时间和H2O2投加次数对废水COD去除效果的影响。结果表明，通过Fenton试剂氧化可使废水中的COD值从13500mg／L降至4030mg／L，COD去除率达到70．1％。废水的BOD5／COD值从0．202提高至0．568，可生化性得到较大提高，为后续处理创造了条件。研究成果为发酵法甘油生产提取废水的预处理提供了一种非常有效的方法。     

Fenton氧化法深度处理甲醛废水

采用Fenton氧化法深度处理经生化降解后的甲醛废水,结果表明,Fenton氧化法深度处理甲醛废水是可行的,在合适的反应条件下,降解初始COD为150 mg/L左右的甲醛废水,COD去除率达30%以上;Fe2+与H2O2的投加比例、投加量及投加方式、反应温度、pH、反应时间对处理效果都有不同程度的影响。     

光助Fenton氧化、化学絮凝法联合处理R盐废水的研究

采用光助Fenton氧化、化学絮凝法联合处理生物难降解的R盐废水,考察了不同反应条件对处理效果的影响.试验结果表明,光助Fenton氧化、化学絮凝法联合处理废水,两者之间存在协同作用,可以提高处理效果,降低处理成本.在最佳试验条件下,R盐废水经光助Fenton氧化、化学絮凝法联合处理后,COD去除率可达90%以上.     

Fenton法氧化处理水中土霉素的研究

为了评价Fenton法预处理抗生素生产废水中残留的高浓度土霉素的可行性,对Fenton试剂(Fe2 -H2O2)法催化氧化降解水溶液中的土霉素进行了研究.探讨了H2O2与Fe2 投加比例、投加量以及起始pH值对降解效果的影响,同时考察了土霉素废水中大量共存的草酸根离子对氧化过程的影响.结果表明,当H2O2与Fe2 按照5:1的比例投加时降解效率最高,最佳初始pH值在3.0-4.0之间.在最佳投加比例下,H2O2投加量为0.9 mmol/L,100 mg/L的土霉素可在10 min内得到完全降解.最佳反应条件下经过处理后土霉素水溶液TOC的去除率达40%左右,可生化性(BOD5/COD)也得到明显的改善.水中共存的草酸根离子对氧化效率具有明显的影响,但通过增加亚铁离子的量可以消除草酸的影响.     

Fenton-接触氧化联合工艺处理铁合金镀件电镀前处理废水

电镀前处理废水中含有大量难降解有机物,成分复杂,用传统生化法难以处理达标。本实验采用Fenton氧化技术对前处理废水进行预处理,再用生物接触氧化技术后续降解COD,使出水中COD达到《电镀污染物排放标准》(GB21900-2008)表3的水质要求。实验采用实际电镀生产废水,COD=300 mg/L,通过芬顿-生物接触氧化因素实验,优化工艺参数,去除率可达到83%以上,COD降到50 mg/L以下.最佳芬顿反应参数为:pH=3.0,COD/H2O2=1.5,Fe2+/H2O2=2,反应时间t=10 min;生物接触氧化法最佳水力停留时间为7 h,进水pH在6~8之间。     

光助Fenton氧化、化学絮凝法联合处理R盐废水的研究

采用光助Fenton氧化、化学絮凝法联合处理生物难降解的R盐废水,考察了不同反应条件对处理效果的影响。试验结果表明,光助Fenton氧化、化学絮凝法联合处理废水,两者之间存在协同作用,可以提高处理效果,降低处理成本。在最佳试验条件下,R盐废水经光助Fenton氧化、化学絮凝法联合处理后,COD去除率可达90%以上。     

响应面法优化Fenton法预处理腈纶废水

为得到Fenton法预处理腈纶废水的最优条件参数,以初始pH、H_2O_2投加量、Fe~(2+)投加量、反应时间为考察因素,废水COD去除率为评价指标,在单因素实验基础上,通过Box-Behnken方案构建与拟合响应面模型,分析4个独立因素及各因素之间的交互作用对COD去除效果的影响。确定了最佳Fenton法预处理工艺:初始pH为3.0,H_2O_2投加量为5.0mL/L,Fe~(2+)投加量为4.9g/L,反应时间为150min时。此时,COD去除率预测结果为44.08%,实际运行结果为43.89%,表明该模型可靠。考察了无机离子对Fenton法预处理的影响,并研究预处理前后腈纶废水可生化性的变化。结果表明,SO~(2-)_4对腈纶废水的降解无明显影响,Fenton法预处理显著改善了腈纶废水可生化性。通过对比Fenton法预处理前后腈纶废水的傅立叶变换红外光谱(FTIR)可以得出,Fenton法预处理有效去除了腈纶废水中难降解有机物。     

活性炭吸附-Fenton氧化处理高盐有机废水

采用活性炭吸附-Fenton氧化耦合工艺处理高盐度难降解有机废水的性能。考察了不同工艺参数对活性炭吸附及Fenton氧化对高盐有机废水处理效率的影响。结果表明,采用活性炭单独处理时,在pH=6.0,活性炭投加量为9.0g/L,吸附时间为60 min条件下,COD去除率最大,达到47.5%。活性炭吸附处理后,废水再采用Fenton氧化处理,在FeSO4.7H2O投加量为3.0 g/L,H2O2投加量为4.7 g/L,反应时间为30 min条件下,COD去除率最大,达到84.4%。整体而言,经过活性炭吸附和Fenton氧化处理后,废水COD由初始浓度13 650 mg/L降至560 mg/L,去除率达到95.9%。活性炭吸附-Fenton氧化耦合工艺适合高盐度难降解有机废水的处理。     

某化工园区污水分类收集分质处理系统设计

为了提高某化工园区污水处理效率以及降低污水处理费用,园区环保部门拟对园区污水收集体系进行升级改造。改造方案采用分类收集分质处理的设计思路,同时创新型的采用OUR污泥呼吸法对企业废水分为难降解有毒、难降解无毒、可生化3类,3类废水进入不同的收集池后前2类废水进行芬顿+微电解预处理,可生化类别直接进入生化系统。该种工艺路线较传统的全部接入进行预处理的方法更具先进性、高效性和经济性,可作为一种先进理念的收集体系使用到其他工业园区中进行推广应用。     

Fenton法及其在废水处理中的应用研究

Fenton法在处理难降解有机污染物时具有独特的优势．是一种很有应用前景的废水处理技术。文章介绍了该技术的发展过程、主要类型及应用状况,并对其在废水处理中的优势．存在问题和发展趋势作出评述。     

Chemical oxygen demand reduction of various wastewater types using magnetic field-assisted fenton reaction.

Constant magnetic field (CMF) was investigated for its potential to intensify chemical oxygen demand (COD) removal in wastewater when applied with a generalized Fenton reaction. Various types of industrial and domestic wastewater were tested in the experiment. A significant dependence was observed between the wastewater type, dose of reacting substances, time of exposure to CMF, effectiveness of COD removal, and the rate of the advanced oxidation process. The use of CMF resulted in the improvement of the treatment process; however, the efficiency depended to a great extent on the type of wastewater and characteristics of the contained organic matter. Domestic wastewater seemed to be most amenable to the applied treatment (82% COD reduction). The least reduction in COD occurred for wood industry wastewater. In the analyzed wastewater, intense oxidation was observed during the first 60 minutes of the process. Longer reaction time did not increase COD reduction, with the exception of wood industry wastewater. The experiment revealed the possibility of applying smaller doses of the Fenton's reagent, thereby keeping up unchanged treatment efficiency, provided that CMFs are applied.     

Pre-oxidation and coagulation of textile wastewater by the Fenton process

This paper evaluates the Fenton process, involving oxidation and coagulation, for the removal of color and chemical oxygen demand (COD) from synthetic textile wastewater containing polyvinyl alcohol and a reactive dyestuff, R94H. The experimental variables studied include dosages of iron salts and hydrogen peroxide, oxidation time, mixing speed and organic content. The results show that color was removed mainly by Fenton oxidation. The color removal reached a maximum of 90% at a reaction time of 5 min under low dosages of H2O2 and Fe2+. In contrast, the COD was removed primarily by Fenton coagulation, rather than by Fenton oxidation. The ratio of removal efficiency between Fenton process and ferric coagulation was 5.6 for color removal and 1.2 for COD removal. It is concluded that Fenton process for the treatment of textile wastewater favors the removal of color rather than COD.     

类Fenton氧化—好氧移动床生物膜法处理抗生素发酵废水

采用类Fenton氧化-好氧移动床生物膜(MBBR)法处理难降解抗生素发酵废水,探讨了H2O2和草酸投加量对类Fenton氧化工艺以及HRT和曝气量对好氧MBBR反应器的影响.实验结果表明,当类Fenton氧化工艺的最佳操作参数为反应溶液H2O2和草酸初始质量浓度分别为150、45 mg/L、30 W/154 nm紫外灯照射1 h、pH为3.0,在曝气搅拌条件下,COD平均去除率为80.9%.当类Fenton氧化工艺出水pH在7.0时,废水中的污染物还可以进一步被混凝去除.好氧MBBR反应器的最佳工艺参数为HRT 12 h、曝气量0.10 m3/h以及填料填充比(体积比)30%,最终废水COD平均去除率为99.1%,达到<污水综合排放标准>(GB 8978-1996)三级标准要求.     

不同来源高浓度有机废水的集中处理

按照水质情况,将多种来源于不同工业生产过程中的高浓度有机废水划分为高悬浮固体乳化液废水、难生化高浓度有机废水、高悬浮固体不含油有机废水、含铬有机废水和杂质含量较少的乳化液废水5类,分别采用酸化破乳/Fen-ton氧化/混凝/絮凝、Fenton氧化/混凝/絮凝、混凝/絮凝、还原/混凝/絮凝、震动膜过滤技术作为生化预处理技术,并通过小试和中试验证了各技术的效果。实验结果表明,按照上述分类结果,采用不同预处理技术可以得到良好的效果,废水水质明显改善,满足继续生化处理的基本条件。各预处理生产装置处理效果稳定,同时生化系统已经稳定运行120天以上,COD去除率超过90%,出水经过低剂量的Fenton试剂处理后可达到《污水排入城镇下水道水质标准》(CJ343-2012)。     

Fenton-水解酸化-接触氧化处理模拟磷霉素钠制药废水

对模拟磷霉素钠制药废水进行Fenton-水解酸化-接触氧化小试处理实验,考察了COD、有机磷的去除效果,并对处理前后的废水进行了GC-MS分析。结果显示,增加了Fenton预处理后磷霉素钠制药废水的COD和有机磷分别降低到100和2 mg/L,去除率均可达87%以上,出水COD满足化学制药行业污染物排放标准(GB 21904-2008);Fenton过程对制药厂废水中的复杂有机物去除效果明显,GC-MS结果表明,出水中基本检测不到复杂有机物。与制药厂采用的水解酸化-接触氧化处理效果相比,增加Fenton预处理可以提高废水的可生化性和系统的处理效率。     

The role of ferrous ion in Fenton and photo-Fenton processes for the degradation of phenol

The efficiency of different Fenton-related oxidative processes such as Fenton, solar-Fenton and UV-Fenton were examined using phenol as a model compound in simulated and industrial wastewater. A batch study was conducted to optimize parameters like pH, hydrogen peroxide concentration and ferrous ion concentration governing the Fenton process. At optimum conditions, different Fenton-related processes were compared for the degradation of phenol. Increased degradation and mineralisation efficiency were observed in photo-Fenton processes as compared to conventional Fenton process. The maximum mineralising efficiency for phenol with Fenton, solar and UV-Fenton processes were 41%, 96% and 97% respectively. In Fenton process, carboxylic acids like acetic acid and oxalic acid were formed as end products during the degradation of phenol while in photo-Fenton processes, both these ions were identified during the early stages of phenol degradation and were oxidized almost completely at 120 min of the reaction time. In photo-Fenton processes (solar and UV light) complete degradation were observed with 0.4 mM of Fe2+ catalyst as compared to 0.8 mM of Fe2+ in conventional Fenton process. In Fenton and solar-Fenton processes, an iron reusability study was performed to minimize the amount of iron used in treatment process. The efficacy of Fenton and solar-Fenton processes was applied to effluent from phenol resin-manufacturing unit for the removal and mineralisation of phenol.