Removal of selenite using ‘waste’ Fe(III)/Cr(III) hydroxide: Adsorption kinetics and isotherms

Removal of selenite [Se (IV)] from aqueous solution on to industrial solid ‘waste’ Fe(III)/Cr(III) hydroxide as adsorbent was investigated in the present article. Maximum adsorption was found to be at pH 4.0. Pretreated Fe(III)/Cr(III) hydroxide was found to be more efficient for the removal of selenite compared to untreated adsorbent. Langmuir and Freundlich isotherms have been studied. The Langmuir adsorption capacity (Q ₀) of the pretreated and untreated adsorbents was found to be 15.63 and 6.04?mg?g^?1, respectively. The adsorption process fit into the second-order kinetics. Thermodynamic parameters show that the adsorption process is spontaneous and endothermic in the temperature range 32 to 60°C. Coexisting anions vanadate and phosphate significantly affect the adsorption of selenite for both the pretreated and untreated adsorbents. Molybdate, thiocyanate, sulphate, nitrate and chloride do not significantly affect the removal of selenite for pretreated adsorbent.     

Removal of arsenic (V) from aqueous medium using manganese oxide coated lignocellulose/silica adsorbents

Arsenic (V) adsorption on manganese oxide coated rice wastes was investigated in this study. The modified adsorbents were characterized by Fourier-transform infrared spectroscopy, scanning electron microscopy, and pH measurements to determine the point of zero charge. Batch adsorption equilibrium experiments were conducted to study the effects of pH, contact time, and initial concentration on arsenic removal efficiency. The adsorption capacity of rice waste was significantly improved after modification with permanganate. The Langmuir isotherm model fitted the equilibrium data better than the Freundlich model which confirms surface homogeneity of the adsorbent. Maxima adsorption capacities are determined as 10 and 12 mg/g at pH 3 for manganese oxide coated rice husk and straw, respectively. The adsorption energy indicates that the adsorption process may be dominated by chemisorption. Pseudo-second-order rate equation described the kinetics sorption of arsenic with good correlation coefficients, better than a pseudo-first-order equation. Manganese oxide coated rice husk and straw appear to be promising low cost adsorbents for removing arsenic from water.     

Removal and recovery of uranium(VI) by adsorption onto a lignocellulosic-based polymeric adsorbent containing amidoxime chelating functional group

A new adsorbent (ABS) with amidoxime functional group was prepared through graft polymerization of acrylonitrile onto banana stem (BS) using ceric ammonium nitrate (CAN)/HNO₃ initiator system, followed by treatment with hydroxylamine hydrochloride in alkaline solution. Infrared spectroscopy, surface area analyzer, thermogravimetry, and potentiometric titration were used for the characterization of the adsorbent. Effective removal of U(VI) ions was demonstrated at the pH range 4.0–6.0. The mechanism for the removal of U(VI) ions by ABS was based on complexation adsorption model. Equilibrium was achieved in approximately 3 h. The experimental kinetic data were analyzed using first-order, second-order, and Elovich kinetic models, and are well fitted with second-order kinetics. The temperature dependence indicates an exothermic process. U(VI) adsorption was found to decrease with increase of ionic strength. The Freundlich isotherm model fitted the experimental equilibrium data well. The adsorption efficiency was tested using synthetic nuclear industry effluents. The maximum adsorption capacity for U(VI) removal was found to be 80 mg g^-1 at 20°C. Adsorbed U(VI) ions were desorbed effectively, about 99% by 0.2 M HCl. Repeated adsorption/desorption cycles show the feasibility of the ABS for the removal of U(VI) ions from water and nuclear industry effluents.     

Adsorption of cadmium from aqueous solution using Rooibos shoots as adsorbent

The use of Rooibos shoots, a natural adsorbent, for cadmium removal from wastewater is proposed. The effects of initial pH, adsorbent dosage, contact time, and initial concentration were investigated in the batch adsorption mode. The optimum pH was found to be 5.5. Isotherm and kinetic data were modeled; the data fitted best to the Freundlich model, and, kinetically, the adsorption was of pseudo-second order as shown by the high R² value of 0.9928 along with close agreement between the experimental q_e (13.9 mg g^?1) and calculated q_e (14.24 mg g^?1) values. The studied biomass material was found to be effectively used for removal of cadmium from contaminated mine wastewater.     

High removal of phosphate from wastewater using silica sulfate

This report shows that silica sulfate is removing phosphate from wastewater very efficiently. Phosphorus removal and recovery from wastewater is a worldwide issue due to pollution of natural waters by phosphate and depletion of phosphate ores. Adsorption is a process that can remove phosphate at low concentrations. Adsorption also allows the recovery of phosphate for possible re-use. Here, we studied the adsorption of phosphate from wastewater using commercial Zr ferrite, Zr-MCM 41 and silica sulfate. We calculated equilibrium isotherms, kinetic models and thermodynamic effects under conditions similar to real wastewaters. We found that the equilibrium data for the adsorption of phosphate were best fitted to the Freundlich model. The results show that the maximum uptake of phosphate was 3.36 mg g⁻¹ for Zr-MCM, 27.73 mg g⁻¹ for Zr ferrite and 46.32 mg g⁻¹ for silica sulfate. The kinetic results of the three adsorbents were satisfactorily predicted using a pseudo-second-order model. We found that silica sulfate provided excellent characteristics in terms of the maximum adsorption and rate constant for the adsorption of phosphate. The thermodynamic data showed that increasing the temperature enhanced the adsorption of phosphate onto silica sulfate. Our findings will help to define efficient methods to remove phosphate from wastewater.     

As(III) adsorption onto Fe-impregnated food waste biochar: experimental investigation,modeling, and optimization using response surface methodology

Biochar derived from food waste was modified with Fe to enhance its adsorption capacity for As(III), which is the most toxic form of As. The synthesis of Fe-impregnated food waste biochar (Fe-FWB) was optimized using response surface methodology (RSM), and the pyrolysis time (1.0, 2.5, and 4.0 h), temperature (300, 450, and 600 °C), and Fe concentration (0.1, 0.3, and 0.5 M) were set as independent variables. The pyrolysis temperature and Fe concentration significantly influenced the As(III) removal, but the effect of pyrolysis time was insignificant. The optimum conditions for the synthesis of Fe-FWB were 1 h and 300 °C with a 0.42-M Fe concentration. Both physical and chemical properties of the optimized Fe-FWB were studied. They were also used for kinetic, equilibrium, thermodynamic, pH, and competing anion studies. Kinetic adsorption experiments demonstrated that the pseudo-second-order model had a superior fit for As(III) adsorption than the pseudo-first-order model. The maximum adsorption capacity derived from the Langmuir model was 119.5 mg/g, which surpassed that of other adsorbents published in the literature. Maximum As(III) adsorption occurred at an elevated pH in the range from 3 to 11 owing to the presence of As(III) as H₂AsO₃^? above a pH of 9.2. A slight reduction in As(III) adsorption was observed in the existence of bicarbonate, hydrogen phosphate, nitrate, and sulfate even at a high concentration of 10 mM. This study demonstrates that aqueous solutions can be treated using Fe-FWB, which is an affordable and readily available resource for As(III) removal.

     

Effective removal of Cobalt(II) ions from aqueous solutions and nuclear industry wastewater using sulfhydryl and carboxyl functionalised magnetite nanocellulose composite: batch adsorption studies

A new adsorbent sulfhydryl and carboxyl functionalized magnetite nanocellulose composite [(MB-IA)-g-MNCC] was synthesized by graft co-polymerization of itaconic acid onto magnetite nanocellulose (MNCC) using EGDMA as cross linking agent and K₂S₂O₈ as free radical initiator. The adsorption occurs maximum in the pH 6.5. The best fitted kinetic model was found to be pseudo-second-order kinetics. Therefore the mechanism of Co(II) adsorption onto (MB-IA)-g-MNCC follows ion exchange followed by complexation. The Langmuir model was the best fitted isotherm model for the adsorption of Co(II) onto the (MB-IA)-g-MNCC. Simulated nuclear power plant coolant water samples were also treated with (MB-IA)-g-MNCC to demonstrate its efficiency for the removal of Co(II) from aqueous solutions in the presence of other metal ions. To recover the adsorbed Co(II) ions and also to regenerate the adsorbent to its original state 0.1?M HCl was used as suitable desorbing agent. Six cycles of adsorption-desorption experiments were conducted and was found that adsorption capacity of (MB-IA)-g-MNCC has been decreased from 97.5% in the first cycle to 84.7% in the sixth cycle. Recovery of Co(II) using 0.1?M HCl decreased from 93.2% in the first cycle to 79.3% in the sixth cycle.

Abbreviations: T: absolute temperature; q_e: amount adsorbed at equilibrium; q_t: amount adsorbed at time t; CELL: cellulose; Co: cobalt; C_e: concentration at equilibrium; C_HCl: concentration of HCl; C_NaOH: concentration of NaOH; C_A: concentrations of acid; C_B: concentrations of base; W_g: dry weight of composite; W_i: dry weight of MNCC; DS: energy dispersive spectra; EGDMA: ethylene glycol dimethacrylate; Ce: equilibrium concentration; K_L: equilibrium constant; F: Faradays constant; FTIR: Fourier transform infrared spectra; ΔG^o: free energy change; K_F: Freundlich adsorption capacity; 1/n: Freundlich constant; R: gas constant; D: grafting density; EC_o: initial concentration; IA: itaconic acid; IA-g-MNCC: itaconic acid-grafted-magnetite nanocellulose composite; b: Langmuir constant; MNCC: magnetite nanocellulose composite; Q⁰: Maximum adsorption capacity; (MB-IA)-g-MNCC: 2-mercaptobenzamide modified itaconic acid-grafted-magnetite nanocellulose composite; NC: nanocellulose; pH_pzc: Point of zero charge; K₂S₂O₈: potassium peroxy sulphate; k₁: pseudo-first-order rate constant; k₂: pseudo-second-order rate constant; SEM: scanning Electron Microscope; b_s: Sips adsorption capacity; Q_s: Sips maximum adsorption capacity; ΔH°: standard enthalpy change; ΔS°: standard entropy change; A: surface area; σ₀: surface charge density; 1/n_s: surface heterogeneity factor; VSM: vibrating sample magnetometer; V: volume of solution; W: weight of (MB-IA)-g-MNCC; M_composite: weight of the composite; XRD: X-ray diffraction     

One-pot preparation of graphene oxide magnetic nanocomposites for the removal of tetrabromobisphenol A

A simple solvothermal method was used to prepare monodisperse magnetite (Fe₃O₄) nanoparticles attached onto graphene oxide (GO) sheets as adsorbents to remove tetrabromobisphenol A (TBBPA) from an aqueous solution. These Fe₃O₄/GO (MGO) nanocomposites were characterized by transmission electron microscopy. The adsorption capacity at different initial pH, contact duration, and temperature were evaluated. The kinetics of adsorption was found to fit the pseudo-second-order model perfectly. The adsorption isotherm well fitted the Langmuir model, and the theoretical maximum of adsorption capacity calculated by the Langmuir model was 27.26 mg?g^-1. The adsorption thermodynamics of TBBPA on the MGO nanocomposites was determined at 303 K, 313 K, and 323 K, respectively. The results indicated that the adsorption was spontaneous and endothermic. The MGO nanocomposites were conveniently separated from the media by an external magnetic field within several seconds, and then regenerated in 0.2 M NaOH solution. Thus, the MGO nanocomposites are a promising candidate for TBBPA removal from wastewater.     

Removal of fluoride from water using titanium-based adsorbents

Three adsorbents including TiO₂, Ti-Ce, and Ti-La hybrid oxides were prepared to remove fluoride from aqueous solution. The Ti-Ce and Ti-La hybrid adsorbents obtained by the hydrolysis-precipitation method had much higher sorption capacity for fluoride than the TiO₂ adsorbent prepared through hydrolysis. Rare earth (Ce and La) oxides and TiO₂ exhibited a synergistic effect in the hybrid adsorbents for fluoride sorption. The sorption equilibrium of fluoride on the three adsorbents was achieved within 4 h, and the pseudo-second-order model described the sorption kinetics well. The sorption isotherms fitted the Langmuir model well, and the adsorption capacities of fluoride on the Ti-Ce and Ti-La adsorbents were about 9.6 and 15.1 mg·g^-1, respectively, at the equilibrium fluoride concentration of 1.0 mg·L^-1, much higher than the 1.7 mg·g^-1 on the TiO₂. The sorption capacities of fluoride on the three adsorbents decreased significantly when the solution pH increased from 3 to 9.5. The electrostatic interaction played an important role in fluoride removal by the three adsorbents, and Fourier transform infrared (FTIR) analysis indicated that the hydroxyl groups on the adsorbent surface were involved in fluoride adsorption.     

Development of chitosan-alginate based biosorbent for the removal of p-chlorophenol from aqueous medium

Removal of p-chlorophenol (pCP) from synthetic aqueous solutions was studied through adsorption on a biosorbent developed from chitosan (CS) and sodium alginate (SA), the natural cationic and anionic polysaccharides, respectively. Chitosan-coated sodium alginate beads were prepared and treated with calcium chloride solution in order to improve the stability as well as hydrophobic character. The resulting beads (CS/CA) were characterized using FTIR spectra, scanning electron microscopy (SEM), and BET surface analysis. The efficiency of this biosorbent in removing pCP from aqueous medium was studied under batch equilibrium and dynamic column flow experimental conditions. The binding capacity of the biosorbent was studied as a function of initial pH, contact time, initial concentration of adsorbate and amount of biomass. The data were fitted to pseudo-first-order, pseudo-second-order, and Weber–Morris models and found that the adsorption process followed pseudo-first-order kinetics. Further, the equilibrium data were fitted to Freundlich, Langmiur, and Dubinin–Radushkevich (D–R) adsorption isotherms and the isotherm constants were evaluated for adsorption of pCP. The maximum monolayer adsorption capacity of CS/CA beads was found to be 127 mg g^?1. Column flow results were used to generate breakthrough curves. The experimental results suggested that the chitosan–calcium alginate blended biosorbent was effective for the removal of pCP from aqueous medium.     

Adsorptive features of banana (Musa paradisiaca) stalk-based activated carbon for malachite green dye removal

Chemically prepared activated carbon derived from banana stalk (BSAC) was used as an adsorbent to remove malachite green (MG) dye from aqueous solution. BSAC was characterised using thermogravimetric analyser, Brunauer Emmett Teller, Fourier transform infrared spectrometry, scanning electron microscopy, pH_pzc, elemental analysis and Boehm titration. The effectiveness of BSAC in adsorbing MG dye was studied as a function of pH, contact time, temperature, initial dye concentration and repeated desorption–adsorption processes. pH_pzc of BSAC was 4.5 and maximum dye adsorption occurred at pH 8.0. The rate of dye adsorption by BSAC was very fast initially, attaining equilibrium within 120 min following a pseudo-second-order kinetic model. Experimental data were analysed by Langmuir, Freundlich and Dubinin–Raduschevich isotherms. Equilibrium data fitted best into the Langmuir model, with a maximum adsorption capacity of 141.76 mg·g^?1. Δ G ⁰ values were negative, indicating that the process of MG dye adsorption onto BSAC was spontaneous. The positive values of Δ H ⁰ and Δ S ⁰ suggests that the process of dye adsorption was endothermic. The regeneration efficiency of spent BSAC was studied using 0.5 M HCl, and was found to be in the range of 90.22–95.16% after four cycles. This adsorbent was found to be both effective and viable for the removal of MG dye from aqueous solution.     

Low-cost and efficient adsorbent derived from pyrolysis of Jatropha curcas seeds for the removal of Cu2+ from aqueous solutions

Biochar, is a low-cost material that can be used as an alternative adsorbent for the removal of heavy metals. In this study, a low-cost and efficient adsorbent synthesised from Jatropha curcas seeds was used for the uptake of Cu²⁺ from aqueous solutions. The as-prepared adsorbent was characterised by scanning electron microscopy and Brunauer–Emmett–Teller analysis post calcination at 500 °C, its BET surface area and total pore volume were 39.62?m²?g^?1 and 0.049?m³?g^?1, respectively. Subsequently, the effects of initial pH of the solution, contact time, and adsorbent material dosage on the adsorption of Cu²⁺ by the prepared adsorbent were investigated. The as-prepared adsorbent exhibited a high performance, with a maximum adsorption amount of 32.895?mg?g^?1 for Cu²⁺ at pH 5.0 and 25 °C, owing to the presence of ?OH, C=O, C–O, Si-O-Si, and O-Si-O on its surface. The predominant Cu²⁺ adsorption mechanism was assumed to be ion exchange. Notably, the Cu²⁺ adsorption could attain equilibrium within 90?min. In addition, the fact that the Langmuir model was a better fit than the Freundlich model for the isotherm data of Cu²⁺ adsorption by the as-prepared adsorbent suggested that the adsorption of Cu²⁺ was a monolayer adsorption process.     

Modelling the kinetics and equilibrium properties of cadmium biosorption by river green alga and water hyacinth weed

Cadmium biosorption properties of non-living, dried river green alga from a river source, and water hyacinth weed, Eichhornia crassipes from a lake in Zimbabwe have been investigated. The cadmium uptake was found to depend on initial pH, uptake being apparently minimal at low pH values and increasing with an increase in pH. Cadmium biosorption kinetics by both samples is fast, with 80% of total uptake occurring within 60?min. The effect of initial solution pH and initial cadmium concentration on cadmium biosorption from a cadmium solution has been studied. The data for algal biomass fitted the Langmuir monolayer adsorption isotherm, while the biosorption of the metal by water hyacinth weed fitted the Freundlich adsorption isotherm with 1/n values all less than 1. Maximum metal uptake capacities were recorded using 0.35?g of biomass and a 250?mg?L^?1 cadmium solution at pH 6.5 and at 25°C and these were about 85 and 50?mg?L^?1 for water hyacinth weed and green alga, respectively, showing that water hyacinth weed offered a greater potential for cadmium uptake. The absorption was described by pseudo-second order rate model and the rate constant and equilibrium sorption capacity are reported.     

Comparing the adsorption behaviors of Cd,Cu and Pb from water onto Fe-Mn binary oxide,MnO2 and FeOOH

The adsorption potential of FMBO, FeOOH, MnO₂ for the removal of Cd²⁺, Cu²⁺ and Pb²⁺ in aqueous systems was investigated in this study. Comparing to FMBO and FeOOH, MnO₂ offered a much higher removal capacity towards the three metal ions. The maximal adsorption capacity of MnO₂ for Cd²⁺, Cu²⁺ and Pb²⁺ were 1.23, 2.25 and 2.60 mmol·g^-1, respectively. And that for FMBO were 0.37, 1.13, and 1.18 mmol·g^-1 and for FeOOH were 0.11, 0.86 and 0.48 mmol·g^-1, respectively. The adsorption behaviors of the three metal ions on the three adsorbents were all significantly affected by pH values and heavy metal removal efficiency increased with pH increased. The Langmuir and Freundlich adsorption models were used to describe the adsorption equilibrium of the three metal ions onto the three adsorbents. Results showed that the adsorption equilibrium data fitted well to Langmuir isotherm and this indicated that adsorption of metal ions occurred on the three metal oxides adsorbents limited to the formation of a monolayer. More negative charged of MnO₂ surface than that of FMBO and FeOOH could be ascribed by lower pH_iep of MnO₂ than that of FMBO and FeOOH and this could contribute to more binding sites on MnO₂ surface than that of FMBO and FeOOH. The higher metal ions uptake by MnO₂ than FMBO and FeOOH could be well explained by the surface charge mechanism.     

Removal of congo red and basic violet 1 by chir pine (Pinus roxburghii) sawdust,a saw mill waste: batch and column studies

The efficiency of chir pine sawdust (CPS) for adsorptive removal of the dyes, congo red (CR) and basic violet 1 (BV), from aqueous solution was evaluated using batch and column studies. The equilibrium was attained in 60 min for CR and 45 min for BV. The adsorption of BV obeyed the Langmuir isotherm model while the Freundlich isotherm fitted the equilibrium data of CR adsorption. The Langmuir monolayer adsorption capacities (Q_o) of CPS for BV and CR were 11.3 and 5.8 g kg^?1, respectively. The kinetic data for CR were best fitted to the Lagergren pseudo-first-order model and for BV to the pseudo-second-order model. The intra-particle diffusion was found to be the rate-controlling step for CR adsorption, while the adsorption kinetics of BV were controlled by both intra-particle and liquid-film diffusion. The thermodynamic parameters indicated that the adsorption process was spontaneous and endothermic in nature. The adsorption activation energy (E_a) for CR (124 kJ mol^?1) implied chemical adsorption while that for BV (5.4 kJ mol^?1) indicated physical adsorption. An increase in the Thomas model constant (K_Th) with increasing flow indicated that for both dyes the mass transport resistance decreased during adsorption. Thus, CPS may be an efficient low-cost adsorbent for decolorization of dye-containing wastewaters.     

Higher Cd adsorption on biogenic elemental selenium nanoparticles

Cadmium (Cd) is a carcinogenic metal contaminating the environment and ending up in wastewaters. There is therefore a need for improved methods to remove Cd by adsorption. Biogenic elemental selenium nanoparticles have been shown to adsorb Zn, Cu and Hg, but these nanoparticles have not been tested for Cd removal. Here we studied the time-dependency and adsorption isotherm of Cd onto biogenic elemental selenium nanoparticles using batch adsorption experiments. We measured ζ-potential values to assess the stability of nanoparticles loaded with Cd. Results show that the maximum Cd adsorption capacity amounts to 176.8 mg of Cd adsorbed per g of biogenic elemental selenium nanoparticles. The ζ-potential of Cd-loaded nanoparticles became less negative from ?32.7 to ?11.7 mV when exposing nanoparticles to an initial Cd concentration of 92.7 mg L^?1. This is the first study that demonstrates the high Cd uptake capacity of biogenic elemental selenium nanoparticles, of 176.8 mg g^?1, when compared to that of traditional adsorbents such as carboxyl-functionalized activated carbon, of 13.5 mg g^?1. An additional benefit is the easy solid–liquid separation by gravity settling due to coagulation of Cd-loaded biogenic elemental selenium nanoparticles.     

Adsorption of vanadate(V) on Fe(III)/Cr(III) hydroxide waste

Adsorption of vanadate(V) from aqueous solution onto industrial solid ‘waste’ Fe(III)/Cr(III) hydroxide was investigated. HCl treated Fe(III)/Cr(III) hydroxide was found to be more efficient for the removal of vanadate(V) compared to untreated adsorbent. The adsorption follows second-order kinetics. Langmuir and Freundlich isotherms have been studied. The Langmuir adsorption capacity (Q ₀) of the treated and untreated adsorbents was found to be 11.43 and 4.67 mg g⁻¹, respectively. Thermodynamic parameters showed that the adsorption process was spontaneous and endothermic in the temperature range 32–60°C. Maximum adsorption was found at system pH 4.0. The adsorption mechanism was predominantly ion exchange. Effect of other anions such as phosphate, selenite, molybdate, nitrate, chloride, and sulfate on adsorption of vanadium has been examined.     

4种吸附剂对对氯苯酚的吸附性能

研究了常温（18℃）条件下粉末活性炭（PAC）、颗粒活性炭（GAC）、天然膨润土和天然海泡石4种吸附剂对对氯苯酚（4-CP）的静态吸附规律,考察了投加灭活活性污泥对吸附性能的影响。结果表明：4种吸附剂对4-CP的吸附符合Langmiur和Freundlich吸附等温式,且吻合良好;4种吸附剂对4-CP的饱和吸附量不同,大小顺序为：PAC〉GAC〉天然膨润土〉天然海泡石;灭活活性污泥与4种吸附剂共存时,降低了4种吸附剂对4-CP的吸附能力。     

Phosphorus release potential and pollution characteristics of sediment in downstream Nansi Lake, China

The research aimed to evaluate present and potential phosphorous pollution due to high sedimentary phosphorus load and release from sediment, when external phosphorus was reduced in downstream Nansi Lake. Pollution load of the sediment and overlying water was investigated. Kinetics and isotherms of adsorption/release of sedimentary phosphorus were studied to determine equilibrium phosphate concentration (EPC₀) and release potential. Kinetics of phosphorus adsorption on sediment and release from sediment were well described by both the pseudo-first-order rate equation and the pseudo-second-order rate equation, but more appropriate to the pseudo-second-order rate equation with the adsorption/release capacity more close to the measured values, suggesting that the processes were chemically rate controlled and dependent on adsorption capacity. Soluble reactive phosphorus (SRP) sorption isotherms on sediment were best fitted by the modified Langmuir model indicating a monolayer adsorption. By comparing EPC₀ and SRP of water, the status (adsorption, releasing or in equilibrium) of sediment phosphorus could be determined. The sediments at site S1, S3, S4, S5, and S7 where the EPC₀s were greater than the SRPs, had a potential to release phosphorus into the water column. However, those sediments at S9, S10, and S12, where the EPC₀s were approximately equal to the SRPs, were in impermanent equilibrium with overlying water in status of phosphorus, the sediments can be likely to release phosphorus to the water column once the equilibrium was broken. Therefore, sedimentary phosphorus can be a secondary pollution source in downstream Nansi Lake.     

Kinetic,equilibrium and thermodynamic studies for the sorption of metribuzin from aqueous solution using banana peels,an agro-based biomass

Banana peels were employed for the removal of metribuzin from aqueous solution. Sorption in the batch mode was optimized regarding pH, contact time, sorbent dose, initial pesticide concentrations, and temperature. The sorption data were fitted to pseudo-first-order, pseudo-second-order, intraparticle diffusion, Elovich, and liquid film diffusion model, the pseudo-second-order exhibiting best fit (R² = 0.9803). Of the four most common sorption isotherm models (Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich), the data followed the Langmuir isotherm with highest correlation. The maximum adsorption capacity was found to be 167 mg g^?1. Gibbs free energy, enthalpy, and entropy showed that the sorption was exothermic and spontaneous.