A Field Intercomparison and Fundamental Characterization of Various Dust Samplers with a Reference Sampler

The European Economic Community Council Directive 80/779/EEC¹ describes air quality limit values and guide values for sulfur dioxide and suspended particulates. However, article 10, paragraph 1 does not define well enough the reference method required, amongst others, for the gravimetric measurement of suspended particulates. It is explicity stated in article 10, paragraph 5 of the directive, that “the commission shall, in selected locations in the member states and in cooperation with the latter, carry out studies on the sampling…of suspended particulates. These studies shall be designed in particular to promote the harmonization of methods of sampling and analysis of these pollutants.” Therefore, in a joint research program the Umweltbundesamt (grant #104 02263), the commission of European Communities (grant #84-B-6642-11-017-11-N) and the U.S. EPA (grant #2-43211-3580) funded the development of a reference dust sampler by the Fraunhofer-lnstitute of Toxicology and Aerosol Research (FhITA, in Hannover, Federal Republic of Germany) in order: ? to study the particle size distribution of ambient air aerosol at a number of selected sites;

? to compare the results obtained with the reference dust sampler with those of particle samplers operated in Europe and the United States;

? to verify the applicability of wind tunnel results to sampling behaviour in the free atmosphere.

     

Trace elements and sea salt aerosols over the sea areas around the Indian sub-continent

The nature and the characteristics of trace elements and sea salt aerosols in the ocean atmosphere around the Indian sub-continent was studied. For this purpose, concentrations of the total suspended particulates (TSP) as well as of its various chemical components together with their mass size distributions were measured on 11 days in May 1983. Over the sea regions around the sub-continent, sampling was done on board the research Vessel Gaveshani using a high volume air sampler and a multistage Andersen sampler. The concentrations of soil-origin elements (Al, Fe, Mn and Ca) were found to be at a maximum over the Arabian sea region suggesting the presence of dust particulates, transported from the Arabian peninsula. The near sea water ratio of CI/ Na was observed in giant size (> 2.5 μm dia) sea salt aerosols suggested that there was very little fractionation in these aerosols. The ratio value considerably decreased in the case of sub-μm sea salt particles. The chemical components originating from soil and from sea salt showed a unimodal distribution whereas those from anthropogenic sources showed a bimodal distribution.     

The Mass Distribution of Large Atmospheric Particles

This paper describes the results of a study to determine the total mass and the mass distribution of atmospheric aerosols, especially that mass associated with particles greater than 10 μm diameter. This study also determined what fraction of the total aerosol mass a standard high-volume air sampler collects and what fraction and size interval settle out on a dust fall plate. A special aerosol sampling system was designed for this study to obtain representative samples of large airborne particles. A suburban sampling site was selected because no local point sources of aerosols existed nearby. Samples were collected under various conditions of wind velocity and direction to obtain measurements on different types of aerosols.

Study measurements show that atmospheric particulate matter has a bimodal mass distribution. Mass associated with large particles mainly ranged from 5 to 100 μm in size, while mass associated with small particles ranged from an estimated 0.03 to 5 μm in size. Combined, these two distributions produced a bimodal mass distribution with a minimum around 5 μm diameter. The high-volume air sampler was found to collect most of the total aerosol mass, not just that fraction normally considered suspended particulate. Dust fall plates did not provide a good or very useful measure of total aerosol mass. The two fundamental processes of aerosol formation, condensation and dispersion appear to account for the formation of a bimodal mass distribution in both natural and anthropogenic aerosols. Particle size distribution measurements frequently are in error because representative samples of large airborne particles are not obtained. Considering this descrepancy, air pollution regulations should specify or be based upon an upper particle size limit.     

Calibration of polyurethane foam (PUF) disk passive air samplers for quantitative measurement of polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs): factors influencing sampling rates

PUF disk passive air samplers are increasingly employed for monitoring of POPs in ambient air. In order to utilize them as quantitative sampling devices, a calibration experiment was conducted. Time integrated indoor air concentrations of PCBs and PBDEs were obtained from a low volume air sampler operated over a 50 d period alongside the PUF disk samplers in the same office microenvironment. Passive sampling rates for the fully-sheltered sampler design employed in our research were determined for the 51 PCB and 7 PBDE congeners detected in all calibration samples. These values varied from 0.57 to 1.55 m3 d(-1) for individual PCBs and from 1.1 to 1.9 m3 d(-1) for PBDEs. These values are appreciably lower than those reported elsewhere for different PUF disk sampler designs (e.g. partially sheltered) employed under different conditions (e.g. in outdoor air), and derived using different calibration experiment configurations. This suggests that sampling rates derived for a specific sampler configuration deployed under specific environmental conditions, should not be extrapolated to different sampler configurations. Furthermore, our observation of variable congener-specific sampling rates (consistent with other studies), implies that more research is required in order to understand fully the factors that influence sampling rates. Analysis of wipe samples taken from the inside of the sampler housing, revealed evidence that the housing surface scavenges particle bound PBDEs.     

A Technique for Respirable Sampling

The purpose of this paper is to describe instrumentation to aerodynamically size suspended particulates found in ambient air and to summarize results of field testing utilizing the new technique.

A four-stage, multiorifice high-volume fractionating impactor with backup filter, which can be operated as a component of the standard high-volume sampler, collects particulate matter in five separate aerodynamic size ranges: 7 micrometer (μm) or larger, 3.3 to 7 μm, 2.0 to 3.3 μm, 1.1 to 2.0 μm, and 0.01 to 1.1 μm.

Comparative field tests utilizing duplicate sampling techniques were conducted to determine the feasibility of using the size fractionator on a routine basis in field operations. Verification of the actual particle size separation was not undertaken; however, earlier tests utilizing laboratory-generated aerosols have been performed with satisfactory results.

The results of field tests indicate that the fractionator can be used to determine the aerodynamic size distribution of particulate matter. A glass fiber surface with a pH of 11.0 was found to adsorb atmospheric acid gases during sampling and thus gave erroneous mass concentration results when compared to the standard high-volume sampler. Glass fiber filters with a pH of 6.5 eliminated the acid gas adsorption.     

Fugitive dust emission source profiles and assessment of selected control strategies for particulate matter at gravel processing sites in Taiwan

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM10), fine suspended particulate (PM2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (< 100 microm) concentrations at the boundary of gravel sites ranged from 280 to 1290 microg/m3, which clearly exceeds the Taiwan hourly air quality standard of 500 microg/m3. Moreover, PM10 concentrations, ranging from 135 to 550 microg/m3, were also above the daily air quality standard of 125 microg/m3 and approximately 1.2 and 1.5 times the PM2.5 concentrations, ranging from 105 to 470 microg/m3. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 microm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.     

Application of semipermeable membrane device (SPMD) to assess air genotoxicity in an occupational environment

Semipermeable membrane device (SPMD) is a passive sampler that sequesters lipophilic contaminants, mimicking the bioconcentration in the fatty tissue of organisms. This study was designed to assess the use of SPMD and biological tests (Comet assay and Ames test) for air monitoring. For this purpose an occupational environment with expected polycyclic aromatic hydrocarbons (PAHs) contamination (coke plant) was selected for a case study. The SPMDs were deployed in five occupational contaminated sites and in a control site. The SPMD dialysates were chemically analysed and examined for in vitro DNA-damaging activity in human cells (Jurkat) by Comet assay and for mutagenicity with the Ames test (TA98 strain, w/o S9). Total suspended particulates were also collected and analysed (GC–MS). No biological effect of SPMD extract was revealed in the control site. On the other hand, air samples collected with SPMDs within the coke plant showed variable degrees of genotoxic and mutagenic activity. The highest effects were associated with the highest PAH level recovered in the SPMDs extracts and in particulate samples.Results obtained support the sensitivity of biological tests associated to SPMD sampling for evaluating the health risk of potentially contaminated work environments highlighting the usefulness of SPMDs for environmental air quality monitoring.     

A High-Volume Sampler for the Determination of Particle Size Distributions in Ambient Air

A size selective particle sampler has been developed for continuous sampling of the urban aerosol over periods ranging from hours to weeks, providing relatively large sample weights. The system, which is now operating in New York City, uses a parallel array of two-stage samplers. The cyclones used as the first stage collectors have 50% particle retention at 3.5,2.5,1.5 and 0.5 µm aerodynamic diameter, respectively. Undersize particles which pass through the cyclones are captured on glass fiber filters. Equal intake velocities are assured by using flow equalizers on the inlets to the cyclones. Accurate control of the flow through the cyclones is obtained by the use of an integrated circuit pressure transducer in conjunction with a specially designed feedback control circuit. The collection efficiencies of the cyclone were calibrated using monodisperse ferric oxide test aerosols tagged with Tc-99m. Mass balances of the par-ticulates collected on the cyclones and filters are obtained for the five sampling stages. Preliminary results show the distributions of the total suspended particulates in New York City to be bimodal. The distributions of lead, copper, and manganese with particle size are also discussed.     

Metallic elements in particulates released during incense-burning at Tzu Yun Yen temple, Taichung, Taiwan

Concentrations of ambient suspended particulates were measured at Tzu Yun Yen temple (120°, 34′ 10”E; 24°, 16′, 12”N), using a Universal sampler and dry deposition plates. The temple is a characteristic incense-burning and semi-open sampling site. PM_2.5 concentrations for Period 1 (average 901μg/m3) were higher than those for Period 2 (average 701μg/m3). Results for average PM_2.5-10concentrations showed equal distributions in Period 1 and Period 2. Average ratios of PM_2.5/ PM₁₀ were higher in Period 1 (74%) than Period 2 (71%). In addition, the suspended particulate (PM₁₀) elements concentrations during Zhong Yuan Jie, and the first and 15th days of nong li for each month (Chinese lunar calendar) were all higher than during non-Zhong Yuan Jie and non-first and non-15th days. Furthermore, the dry deposition velocities of manganese in fine particulates (PM_2.5) and suspended particulates (PM₁₀) were 1.43 and 0.751cm/s, respectively, and the dry deposition velocities of cadmium in fine particulates (PM_2.5) and suspended particulates (PM₁₀) were 1.86 and 0.991cm/s, respectively.     

Visibility and Mass Concentration in a Nonurban Environment

Considerable interest is currently directed toward atmospheric visibility and its relationship to particle size and mass concentration. Previous work has been limited to heavily polluted urban areas, and visibility studies have not included particle size characterization. An air sampling program was carried out in a nonurban, low pollution area to relate: (a) total particulate mass concentration measured with a high-volume sampler, (b) particulate mass size distribution measured with aerodynamic size selective samplers, and (c) visual range measured by the integrating nephelometer. For low suspended particulate mass concentrations, the following relationship was defined between visual range (L_v) and mass concentration (M ? μg/m³):     

Particle size distribution and anion content at a traffic site in Sha-Lu, Taiwan.

Ambient air particle concentrations were sampled by two total suspended particle (TSP) samplers, PM10/PM2.5 specific sampler and micro-orifice uniform deposit impactor (MOUDI) during July-October 2000 at a traffic sampling site in central Taiwan. The average TSP concentration (194 microg/m3) was about a factor of two higher than that of the fraction <2.5 microm (93.2 microg/m3). The mean level of the fraction <10 microm collected by MOUDI (93.2 microg/m3) was about 1 1/2 times higher than that of the size class <2.5 microm (43.8 microg/m3). Furthermore, this fraction showed a certain correlation with the TSP concentration. The particle size distribution was bimodal in the ambient air at the traffic site. The major peaks appear at particle diameters between 0.56-1.0 and 3.2-5.6 microm. The percentages of anions contained in TSP were 0.24% F-, 13.7% Cl, 0.52% Br, 12.0% NO-, 18.9% NO2-, and 54.6% SO2-. The Cl-, NO2-, and NO3- size distributions were all unimodal and the major peaks appeared at 3.2-5.6 microm. The SO2 size distribution was bimodal, with major peaks at 0.32-0.56 and 3.2-5.6.     

Fine (PM2.5), coarse (PM2.5-10), and metallic elements of suspended particulates for incense burning at Tzu Yun Yen temple in central Taiwan

Ambient suspended particulate concentrations were measured at Tzu Yun Yen temple (120 degrees, 34('), 10(") E; 24 degrees, 16('), 12(") N) in this study. This is representative of incense burning and semi-open sampling sites. The Universal-sampler collected fine and coarse particle material was used to measure suspended particulate concentrations, and sampling periods were from 16/08/2001 to 2/1/2002 at Tzu Yun Yen temple. In addition, metallic element concentrations, compositions of PM(2.5) and PM(2.5-10) for incense burning at Tzu Yun Yen temple were also analyzed in this study. The PM(2.5)/PM(10) ratios ranged between 31% and 87% and averaged 70+/-11% during incense the burning period, respectively. The median metallic element concentration order for these elements is Fe>Zn>Cr>Cd>Pb>Mn>Ni>Cu in fine particles (PM(2.5)) at the Tzu Yun Yen temple sampling site. The median metallic element concentration order for these elements is Fe>Zn>Cr>Pb>Cd>Ni>Mn>Cu in coarse particle (PM(2.5-10)) at the Tzu Yun Yen temple sampling site. Fine particulates (PM(2.5)) are the main portion of PM(10) at Tzu Yun Yen temple in this study. From the point of view of PM(10), these data reflect that the elements Fe, Zn, and Cr were the major elements distributed at Tzu Yun Yen temple in this study.     

Quality assured measurements of animal building emissions: odor concentrations

Standard protocols for sampling and measuring odor emissions from livestock buildings are needed to guide scientists, consultants, regulators, and policy-makers. A federally funded, multistate project has conducted field studies in six states to measure emissions of odor, coarse particulate matter (PM(10)), total suspended particulates, hydrogen sulfide, ammonia, and carbon dioxide from swine and poultry production buildings. The focus of this paper is on the intermittent measurement of odor concentrations at nearly identical pairs of buildings in each state and on protocols to minimize variations in these measurements. Air was collected from pig and poultry barns in small (10 L) Tedlar bags through a gas sampling system located in an instrument trailer housing gas and dust analyzers. The samples were analyzed within 30 hr by a dynamic dilution forced-choice olfactometer (a dilution apparatus). The olfactometers (AC'SCENT International Olfactometer, St. Croix Sensory, Inc.) used by all participating laboratories meet the olfactometry standards (American Society for Testing and Materials and European Committee for Standardization [CEN]) in the United States and Europe. Trained panelists (four to eight) at each laboratory measured odor concentrations (dilution to thresholds [DT]) from the bag samples. Odor emissions were calculated by multiplying odor concentration differences between inlet and outlet air by standardized (20 degrees C and 1 atm) building airflow rates.     

High Volume Sampling: Errors Incurred during Passive Sample Exposure Periods

The current Federal EPA reference method for the determination of total suspended particulate matter (TSP) in the atmosphere is the high volume method (hi-vol).¹ The hi-vol sampler is normally operated for a 24 hr period by drawing air through an 8 X 10 in. glass fiber filter at an air sampling flow rate of between 40-60 cfm. TSP samples are presently collected in this manner every 6th day (61 samples/year). Results are used to determine compliance with existing National Primary Ambient Air Quality Standards for TSP (i.e., 260 µg/m³, maximum 24 hr average, not to be exceeded more than once a year; 75 µg/m³, annual geometric mean). However, when the sampling frequency is diminished to only 61 out of a possible 365 measurements each year, the degree of certainty associated with meeting these air quality standards is also decreased.^2,3 This partial sampling schedule also introduces other sampling errors. One such error caused by the exposure of the collection filter both prior and subsequent to the desired sampling day is the subject of the following discussion.     

Performance characteristics of PM10 samplers under calm air conditions

The size range of airborne particles that is closely related to specific deposition regions in the human respiratory tract and excess lung burden of these deposited particles is associated with disease. Size-selective sampling, therefore, needs to be performed to assess the related health risks. Performance criteria applied to these samplers must be well characterized in order to provide accurate and reliable results. The PM10 samplers that have been used in place of the total suspended particulate samplers for the collection of ambient air particles are more relevant to potential inhalation hazards. In order to be certified, a PM10 sampler must meet reliable performance specifications, primarily the aerosol penetration test with liquid and solid particles in a wind tunnel (wind speeds of 2, 8, and 24 km/hr). This testing is intended to assure reasonable accuracy in aerosol measurements. However, the sampler performance under calm air conditions has not been well studied. In the present study, the sampling heads of three devices--the Harvard impactor, the Personal Environmental Monitor (PEM), and the Sierra Andersen model 241 dichotomous sampler PM10 inlet head--were tested for aerosol separation efficiency. With the consideration of bias and imprecision of the measurements, five specimens of each type of sampler were chosen for performance testing, repeating the tests 5 times for each specimen. An ultrasonic atomizing nozzle was used to nebulize potassium sodium tartrate tetrahydrate and dioctyl phthalate particles as the solid and liquid challenge aerosols, respectively. The aerosol number concentrations and size distributions upstream and downstream of the samplers were measured by using an aerosizer calibrated against a settling velocity chamber. The results showed that among the samplers tested, the dichotomous sampler PM10 inlet head had the best fit to the PM10 convention, while the other two samplers not only appeared to have a steeper separation-curve slope but also had significant particle bounce when challenged with solid particles. Analysis of variance also confirmed the superiority of the dichotomous samplers. Surface-coating with oil or grease greatly reduced the problem of particle bounce.     

Sizing of atmospheric particulates with a high volume cascade impactor

This article describes the development of a high volume cascade impactor with a sampling rate of 20 ft³/min that can be powered by high volume blowers in common use for air sampling. With this impactor it is now possible to collect enough sample of atmospheric particulates in a 24 hour period to conveniently determine an aerodynamic size distribution of suspended particulates by gravimetric analysis. The impactor has four stages and an after-filter and separates particles from the air stream by inertial impaction. The effective cutoff diameters for the stages are 7.0, 3.3, 2.0, and 1.1 microns. The after-filter traps the submicron material.     

Fugitive Dust Emission Source Profiles and Assessment of Selected Control Strategies for Particulate Matter at Gravel Processing Sites in Taiwan

Abstract

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM₁₀), fine suspended particulate (PM_2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (<100 µm) concentrations at the boundary of gravel sites ranged from 280 to 1290 µg/m³, which clearly exceeds the Taiwan hourly air quality standard of 500 µg/m³. Moreover, PM₁₀ concentrations, ranging from 135 to 550 µg/m³, were also above the daily air quality standard of 125 µg/m³ and approximately 1.2 and 1.5 times the PM_2.5 concentrations, ranging from 105 to 470 µg/m³. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 µm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.     

Evaluation of the use of diffusive air samplers for determining temporal and spatial variation of volatile organic compounds in the ambient air of urban communities

The Houston-Galveston metropolitan area has a relatively high density of point and mobile sources of air toxics, and determining and understanding the relationship between emissions and ambient air concentrations of air toxics is important for evaluating potential impacts on public health and formulating effective regulatory policies to control this impact, both in this region and elsewhere. However, conventional ambient air monitoring approaches are limited with regard to expense, siting limitations, and representative sampling necessary for adequate exposure assessment. The overall goal of this multiphase study is to evaluate the use of simple passive air samplers to determine temporal and spatial variability of the ambient air concentrations of selected volatile organic compounds (VOCs) in urban areas. Phase 1 of this study, reported here, was a field evaluation of 3M organic vapor monitors (OVMs) involving limited comparisons with commonly used active sampling methods, an assessment of sampler precision, a determination of optimal sampling duration, and an investigation of the utility of a simple modification of the commercial sampler. The results indicated that a sampling duration of 72 hr exhibited generally low bias relative to automated continuous gas chromatography measurements, good overall precision, and an acceptable number of measurements above detection limits. The modified sampler showed good correlation with the commercial sampler, with higher sampling rates, although lower than expected.     

Evaluation of the Use of Diffusive Air Samplers for Determining Temporal and Spatial Variation of Volatile Organic Compounds in the Ambient Air of Urban Communities

Abstract

The Houston-Galveston metropolitan area has a relatively high density of point and mobile sources of air toxics, and determining and understanding the relationship between emissions and ambient air concentrations of air toxics is important for evaluating potential impacts on public health and formulating effective regulatory policies to control this impact, both in this region and elsewhere. However, conventional ambient air monitoring approaches are limited with regard to expense, siting limitations, and representative sampling necessary for adequate exposure assessment. The overall goal of this multiphase study is to evaluate the use of simple passive air samplers to determine temporal and spatial variability of the ambient air concentrations of selected volatile organic compounds (VOCs) in urban areas. Phase 1 of this study, reported here, was a field evaluation of 3M organic vapor monitors (OVMs) involving limited comparisons with commonly used active sampling methods, an assessment of sampler precision, a determination of optimal sampling duration, and an investigation of the utility of a simple modification of the commercial sampler. The results indicated that a sampling duration of 72 hr exhibited generally low bias relative to automated continuous gas chromatography measurements, good overall precision, and an acceptable number of measurements above detection limits. The modified sampler showed good correlation with the commercial sampler, with higher sampling rates, although lower than expected.     

An Inertial-Type Particle Separator for Collecting Large Samples

A two-stage inertial-type particle separator has been developed for collecting large size-selective samples of particulates on filters. The sampler operates at a flow rate of 1.4 cubic feet per minute and may be run for extended periods without change in collecting efficiency. The particle size cut of the sampler is at a diameter of 1.4 microns; separation of greater than 90 percent is obtained for particles below 0.80 micron and above 2.0 microns. The sampler was calibrated with monodisperse polystyrene latexes. Data are presented to relate the separating efficiency of the sampler to its separation parameters.