SGA对垃圾焚烧飞灰中重金属的固化性能研究简

根据EPA 1311、HJ/T 299-2007、HJ/T 300-2007和HJ 557-2009等国内外不同标准,研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性,探讨了六硫代胍基甲酸（sixthio guanidine acid,SGA）、二甲基二硫代氨基甲酸盐（sodium dimethyl dithio carbamate,SDD）和Ca（OH）₂浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明,随着浸提液pH的降低,该厂焚烧飞灰中大部分金属元素的浸出量增大,焚烧飞灰浸出液中的Cd、Ni、Pb和Zn浓度分别超过国家危险废物鉴别标准（GB5085.3-2007）规定值的4.75倍、1.47倍、6.72倍和2.20倍,属于危险废弃物,必须进行稳定化处理。当固化剂SGA加入量为0.1 mol/kg时,稳定化后的重金属浸出浓度已经低于危险废物鉴别标准,且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）₂;当固化剂SGA、SDD和Ca（OH）₂加入量为0.5 mol/kg时,稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB 5085.3-2007）中的规定值。与SDD和Ca（OH）₂相比,SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

Effect of biochars on adsorption of Cu(II), Pb(II) and Cd(II) by three variable charge soils from southern China

The purpose of this study is to compare the relative contribution of different mechanisms to the enhanced adsorption of Cu(II), Pb(II) and Cd(II) by variable charge soils due to incorporation of biochars derived from crop straws. The biochars were prepared from the straws of canola and peanut using an oxygen-limited pyrolysis method at 350 °C. The effect of biochars on adsorption and desorption of Cu(II), Pb(II) and Cd(II) by and from three variable charge soils from southern China was investigated with batch experiments. Based on the desorption of pre-adsorbed heavy metals, the electrostatic and non-electrostatic adsorptions were separated. EDTA was used to replace the heavy metals complexed with biochars and to evaluate the complexing ability of the biochars with the metals. The incorporation of biochars increased the adsorption of Cu(II), Pb(II) and Cd(II) by the soil; peanut straw char induced a greater increase in the adsorption of the three metals. The increased percentage of Cd(II) adsorption induced by biochars was much greater than that for the adsorption of Cu(II) and Pb(II). Cu(II) adsorption on three variable charge soils was enhanced by the two biochars mainly through a non-electrostatic mechanism, while both electrostatic and non-electrostatic mechanisms contributed to the enhanced adsorption of Pb(II) and Cd(II) due to the biochars. Peanut straw char had a greater specific adsorption capacity than canola straw char and thus induced more non-electrostatic adsorption of Cu(II), Pb(II) and Cd(II) by the soils than did the canola straw char. The complexing ability of the biochars with Cu(II) and Pb(II) was much stronger than that with Cd(II) and thus induced more specific adsorption of Cu(II) and Pb(II) by the soils than that of Cd(II). Biochars increased heavy metal adsorption by the variable charge soils through electrostatic and non-electrostatic mechanisms, and the relative contribution of the two mechanisms varied with metals and biochars.     

水泥对垃圾焚烧飞灰的固化处理试验研究

对垃圾焚烧飞灰的化学成分、重金属物质的含量及浸出浓度进行测试分析.结果表明,飞灰中Pb和Cr等重金属物质浸出量超过浸出毒性标准,因而被认为是危险废物,必须进行固化处理.还考察了水泥对焚烧飞灰中重金属物质固化的效果,研究表明当飞灰掺量适当时,重金属物质的固化效果良好.重金属物质通过物理固封、替代,沉淀反应和吸附等形式可固化进水泥水化产物结构中.     

SGA对垃圾焚烧飞灰中重金属的固化性能研究

根据EPA1311、HJ／T299—2007、HJ／T300—2007和HJ557—2009等国内外不同标准,研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性,探讨了六硫代胍基甲酸（sixthioguanidineacid,SGA）、二甲基二硫代氨基甲酸盐（sodiumdimethyldithiocarbamate,SDD）和Ca（OH）2浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明,随着浸提液pH的降低,该厂焚烧飞灰中大部分金属元素的浸出量增大,焚烧飞灰浸出液中的cd、Ni、Ph和zn浓度分别超过国家危险废物鉴别标准（GB5085．3—2007）规定值的4．75倍、1．47倍、6．72倍和2．20倍,属于危险废弃物,必须进行稳定化处理。当固化剂SGA加入量为0．1mol／kg时,稳定化后的重金属浸出浓度已经低于危险废物鉴别标准,且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）2;当固化剂SGA、SDD和Ca（OH）2加入量为0．5mol／kg时,稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB5085．3-2007）中的规定值。与SDD和Ca（OH）：相比,SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

Removal of Pb(II), Cd(II), Cu(II), and Zn(II) by hematite nanoparticles: effect of sorbent concentration, pH, temperature, and exhaustion

Nanoparticles offer the potential to improve environmental treatment technologies due to their unique properties. Adsorption of metal ions (Pb(II), Cd(II), Cu(II), Zn(II)) to nanohematite was examined as a function of sorbent concentration, pH, temperature, and exhaustion. Adsorption experiments were conducted with 0.05, 0.1, and 0.5 g/L nanoparticles in a pH 8 solution and in spiked San Antonio tap water. The adsorption data showed the ability of nanohematite to remove Pb, Cd, Cu, and Zn species from solution with adsorption increasing as the nanoparticle concentration increased. At 0.5 g/L nanohematite, 100 % Pb species adsorbed, 94 % Cd species adsorbed, 89 % Cu species adsorbed and 100 % Zn species adsorbed. Adsorption kinetics for all metals tested was described by a pseudo second-order rate equation with lead having the fastest rate of adsorption. The effect of temperature on adsorption showed that Pb(II), Cu(II), and Cd(II) underwent an endothermic reaction, while Zn(II) underwent an exothermic reaction. The nanoparticles were able to simultaneously remove multiple metals species (Zn, Cd, Pb, and Cu) from both a pH 8 solution and spiked San Antonio tap water. Exhaustion experiments showed that at pH 8, exhaustion did not occur for the nanoparticles but adsorption does decrease for Cd, Cu, and Zn species but not Pb species. The strong adsorption coupled with the ability to simultaneously remove multiple metal ions offers a potential remediation method for the removal of metals from water.     

矿区炼金废渣的固化/稳定化处理

通过对金矿矿区炼金废渣的酸中和能力、净产酸量及浸出毒性实验,测定了废渣的产酸潜力及重金属砷、镉、铅、锌的总量和它们的浸出量。为了合理处置矿区炼金废渣,并为矿区重金属污染土壤的修复提供技术支持,采用石灰、粉煤灰、堆肥化污泥作为添加剂对废渣进行固化/稳定化处理;通过浸出毒性实验对固化/稳定化处理效果进行综合分析,试图寻求一种最佳的稳定剂。结果表明,无论是单独添加石灰、粉煤灰或者堆肥化污泥还是两两组合混合添加,样品浸出液的pH都有升高,As、Cd的浸出浓度都有明显下降,而且两两组合添加比单独添加的固化/稳定化处理效果更好。在两两组合添加中,粉煤灰混合堆肥化污泥的处理效果最好,浸出液的pH值达到7.82,As、Cd的浸出率分别下降72.0%和72.2%。说明粉煤灰混合堆肥化污泥处理炼金废渣效果最佳,同时具有以废治污的资源化生态效能。     

Effect of fly ash characteristics on the removal of Cu(II) from aqueous solution

Fly ash is a particulate substance containing metal oxides, carbon and other microelements. In this study, fly ashes with different quantities of carbon and minerals prepared by a thermal process in the laboratory were used as adsorbents to investigate the contribution of precipitation and adsorption to the removal of aqueous Cu(II). Experimental results showed that the specific surface area of fly ash increased linearly with the quantity of carbon. The specific surface areas of the carbon and mineral fraction were 60 m2/g and 0.68 m2/g, respectively. The specific adsorption capacities of carbon ranged from 2.2 to 2.8 mg Cu/g carbon, while those for mineral were only about 0.63 to approximately 0.81 mg Cu/g mineral. Consequently, the carbon fraction in fly ash was important in the removal of Cu(II) at pH 5. However, Cu(II) removal owing to precipitation increases with a decreasing carbon fraction and the contribution of copper precipitation was estimated to be approximately 23% to approximately 82% of total removal, depending on the carbon fraction of fly ash.     

Seizure modeling of Pb(II) and Cd(II) from aqueous solution by chemically modified sugarcane bagasse fly ash: isotherms, kinetics, and column study

Heavy metal pollution is a common environmental problem all over the world. The purpose of the research is to examine the applicability of bagasse fly ash (BFA)—an agricultural waste of sugar industry used for the synthesis of zeolitic material. The zeolitic material are used for the uptake of Pb(II) and Cd(II) heavy metal. Bagasse fly ash is used as a native material for the synthesis of zeolitic materials by conventional hydrothermal treatment without (conventional zeolitic bagasse fly ash (CZBFA)) and with electrolyte (conventional zeolitic bagasse fly ash in electrolyte media (ECZBFA)) media. Heavy metal ions Pb(II) and Cd(II) were successfully seized from aqueous media using these synthesized zeolitic materials. In this study, the zeolitic materials were well characterized by different instrumental methods such as Brunauer–Emmett–Teller, XRF, Fourier transform infrared spectroscopy, powder X-ray diffraction, and scanning electron microscopic microphotographs. The presence of analcime, phillipsite, and zeolite P in adsorbents confirms successful conversion of native BFA into zeolitic materials. Seizure modeling of Pb(II) and Cd(II) was achieved by batch sorption experiments, isotherms, and kinetic studies. These data were used to compare and evaluate the zeolitic materials as potential sorbents for the uptake of heavy metal ions from an aqueous media. The Langmuir isotherm correlation coefficient parameters best fit the equilibrium data which indicate the physical sorption. Pseudo-second-order and intra-particle diffusion model matches best which indicates that the rate of sorption was controlled by film diffusion. The column studies were performed for the practical function of sorbents, and breakthrough curves were obtained, which revealed higher sorption capacity as compared to batch method. Synthesized zeolitic material (CZBFA and ECZBFA), a low-cost sorbent, was proven as potential sorbent for the uptake of Pb(II) and Cd(II) heavy metal ions.     

Column dynamic studies and breakthrough curve analysis for Cd(II) and Cu(II) ions adsorption onto palm oil boiler mill fly ash (POFA)

This paper investigates the adsorption characteristics of palm oil boiler mill fly ash (POFA) derived from an agricultural waste material in removing Cd(II) and Cu(II) from aqueous solution via column studies. The performance of the study is described through the breakthrough curves concept under relevant operating conditions such as column bed depths (1, 1.5, and 2 cm) and influent metal concentrations (5, 10, and 20 mg/L). The Cd(II) and Cu(II) uptake mechanism is particularly bed depth- and concentration-dependant, favoring higher bed depth and lower influent metal concentration. The highest bed capacity of 34.91 mg Cd(II)/g and 21.93 mg Cu(II)/g of POFA was achieved at 20 mg/L of influent metal concentrations, column bed depth of 2 cm, and flow rate of 5 mL/min. The whole breakthrough curve simulation for both metal ions were best described using the Thomas and Yoon–Nelson models, but it is apparent that the initial region of the breakthrough for Cd(II) was better described using the BDST model. The results illustrate that POFA could be utilized effectively for the removal of Cd(II) and Cu(II) ions from aqueous solution in a fixed-bed column system.     

The role of ammonia on mercury leaching from coal fly ash

The Federal Clean Air Interstate Rule issued in March 2005 will result in many power plants employing ammonia-based technologies to control NO(x) emission. The Clean Air Mercury Rule, issued at the same time, will encourage many power plants to use various technologies to remove mercury from flue gas, generating fly ashes that contain elevated concentrations of mercury. Ammonia forms relatively strong complexes with mercury compared to most other cationic elements and, therefore, may change the leaching characteristics of mercury. Understanding the impact of ammonia on the leaching of mercury from fly ash is critical in predicting the potential environmental impact of future fly ash. Batch methods were used to investigate the ammonia impact on mercury leaching from fly ash under different pH conditions. The results indicated that mercury leaching without external ammonia addition is not significant. However, ammonia addition increased mercury leaching in the alkaline pH range, due to the formation of less adsorbable mercury-ammonia complexes. Washed ash released more mercury than the raw ash if the ammonia concentration is the same, mainly due to the dissolution of some ash components during washing which exposed more mercury on ash surface. Mercury adsorption data indicated that more than 90% of available mercury was adsorbed by fly ash even in the presence of 1000 mg l(-1) ammonia addition.     

油页岩循环流化床锅炉底渣和飞灰中重金属元素浸出毒性研究

为了研究我国桦甸油页岩65 t/h循环流化床锅炉的底渣和飞灰中重金属元素Cr、Cu、Pb和Zn的赋存状态及不同酸度条件下的浸出特性,分别进行了逐级提取实验和分批浸出的淋滤实验。逐级提取实验结果表明,这4种元素在底渣和飞灰中具有基本相当的赋存状态。硫化物结合态和稳定的残渣态是各元素的主要赋存状态,元素的潜在浸出能力大小表现为:PbCrCuZn,飞灰中各元素的潜在浸出能力大于底渣中的。浸出实验结果表明,元素的赋存状态决定了其浸提能力,浸提液的pH值对各元素浸出能力的影响不尽相同,各元素的浸出能力随浸提时间的延长都会趋于平衡,Cr和Pb的浸出浓度都高于地表水和饮用水的国家标准。     

Heavy metals in urban soils of East St. Louis, IL. Part II: Leaching characteristics and modeling

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produced organic and inorganic chemicals, and petroleum refineries. Following a gross assessment of heavy metals in the community soils (see Part I of this two-part series), leaching tests were performed on specific soils to elucidate heavy metal-associated mineral fractions and general leachability. Leaching experiments, including the Toxicity Characteristic Leaching Procedure (TLCP) and column tests, and sequential extractions, illustrated the low leachability of metals in East St. Louis soils. The column leachate results were modeled using a formulation developed for fly ash leaching. The importance of instantaneous dissolution was evident from the model. By incorporating desorption/adsorption terms into the source term, the model was adapted very well to the time-dependent heavy metal leachate concentrations. The results demonstrate the utility of a simple model to describe heavy metal leaching from contaminated soils.     

Biomass-derived materials in the remediation of heavy-metal contaminated water: removal of Cadmium(II) and copper(II) from aqueous solutions

Manganese-coated activated carbon (MCAC) and activated carbon were used in batch experiments for the removal of cadmium(II) and copper(II). Results showed that uptake of Cd(II) and Cu(II) was unaffected by increases in pH (3.0 to 8.5) or concentration (1 to 20 mg/L). Increased ionic strength (from 0.001 to 1 M NaNO3), however, significantly affected the uptake of Cd(II); adsorption of Cu(II) was not affected. Freundlich adsorption isotherm results indicated that MCAC possessed higher sorption capacity than activated carbon. Second-order rate constants were found to be 0.0386 for activated carbon and 0.0633 g/mg x min for MCAC for Cd(II) and 0.0774 for AC and 0.1223 g/mg x min for MCAC for Cu(II). Column experiments showed that maximum sorption capacity of MCAC was 39.48 mg/g for Cu(II) and 12.21 mg/g for Cd(II).     

Equilibrium, kinetic, and thermodynamic biosorption of Pb(II), Cr(III), and Cd(II) ions by dead anaerobic biomass from synthetic wastewater

Purpose

Heavy metals are toxic pollutants released into the environment as a result of different industrial activities. Biosorption of heavy metals from aqueous solutions is a new technology for the treatment of industrial wastewater. The aim of the present research is to highlight the basic biosorption theory to heavy metal removal.

Materials and methods

Heterogeneous cultures mostly dried anaerobic bacteria, yeast (fungi), and protozoa were used as low-cost material to remove metallic cations Pb(II), Cr(III), and Cd(II) from synthetic wastewater. Competitive biosorption of these metals was studied.

Results

The main biosorption mechanisms were complexation and physical adsorption onto natural active functional groups. It is observed that biosorption of these metals was a surface process. The main functional groups involved in these processes were hydroxyl (–OH) and carboxylic groups (C=O) with 37, 52, and 31 and 21, 14, and 34 % removal of Pb(II), Cr(III), and Cd(II), respectively. Langmuir was the best model for a single system. While extended Langmuir was the best model for binary and ternary metal systems. The maximum uptake capacities were 54.92, 34.78, and 29.99 mg/g and pore diffusion coefficients were 7.23, 3.15, and 2.76?×?10^?11 m²/s for Pb(II), Cr(III), and Cd(II), respectively. Optimum pH was found to be 4. Pseudo-second-order was the best model to predict the kinetic process. Biosorption process was exothermic and physical in nature.

Conclusions

Pb(II) offers the strongest component that is able to displace Cr(III) and Cd(II) from their sites, while Cd(II) ions are the weakest adsorbed component.     

Heavy Metals in Urban Soils of East St. Louis,IL Part II: Leaching Characteristics and Modeling

ABSTRACT

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produced organic and inorganic chemicals, and petroleum refineries. Following a gross assessment of heavy metals in the community soils (see Part I of this two-part series), leaching tests were performed on specific soils to elucidate heavy metal-associated mineral fractions and general leachability. Leaching experiments, including the Toxicity Characteristic Leaching Procedure (TLCP) and column tests, and sequential extractions, illustrated the low leachability of metals in East St. Louis soils. The column leachate results were modeled using a formulation developed for fly ash leaching. The importance of instantaneous dissolution was evident from the model. By incorporating desorption/adsorption terms into the source term, the model was adapted very well to the time-dependent heavy metal leachate concentrations. The results demonstrate the utility of a simple model to describe heavy metal leaching from contaminated soils.     

Bioleaching of metal from municipal waste incineration fly ash using a mixed culture of sulfur-oxidizing and iron-oxidizing bacteria

We investigated the behavior and characteristics of metal leaching from municipal solid waste incineration (MSWI) fly ash among pure cultures of a sulfur-oxidizing bacterium (SOB) and an iron-oxidizing bacterium (IOB) and a mixed culture. The IOB has a high metal-leaching ability, though its tolerability against the ash addition is low. The SOB might better tolerate an increase in ash addition than the IOB, though metal leaching ability of the SOB is limited. Mixed culture could compensate for these deficiencies, and high metal leachability was exhibited in the 1% ash culture, i.e., 67% and 78% of leachabilities for Cu and Zn, respectively, and 100% for Cr and Cd. Furthermore, comparably high leachabilities such as 42% and 78% for Cu and Zn were observed even in the 3% ash cultures. Characterization of metal leaching by the mixed culture revealed that the acidic and oxidizing condition had remained stable thorough the experimental period. Ferric iron remained in the mixed culture, and the metal leaching was enhanced by redox mechanisms coupling with the leaching by sulfate. An increase of ferrous iron enhanced the Cr, Cu, and As leaching. The optimum concentration of sulfur existed for As and Cr (5 gl(-1)) and Cu (2 gl(-1)). The presence of the degradable and non-degradable organic compound that must be existed in the natural environment or waste landfills made no significant change in the leachability of metals other than Zn. These results suggested that bioleaching using a mixed culture of SOB and IOB is a promising technology for recovering the valuable metals from MSWI fly ash.     

Modeling batch leaching behavior of arsenic and selenium from bituminous coal fly ashes

Correctly predicting the leaching potential of arsenic (As) and selenium (Se) is critical for assessing the environmental impact of coal fly ash. This study investigated the impacts of several key environmental factors, including pH, leaching time, and ash washing on the batch leaching behavior of As and Se from bituminous coal fly ashes. The experimental results demonstrated that As and Se leaching from fly ash increased beyond the minimal leaching pH ranges. Increasing leaching time increased As leaching but decreased Se leaching in the alkaline pH condition. A speciation-based adsorption model was used to quantify the batch leaching data, and determine the intrinsic leaching parameters including the total batch leachable mass and the adsorption constant of As or Se. The modeling approach was validated by correctly predicting the independent batch leaching data in a broad pH range and a different L/S condition. Experimental and modeling results also demonstrated that ash washing and ash aging (longer leaching time) did not change the adsorption constants of As and Se on the ash surface. However, ash washing could increase the availability of As and Se for leaching.     

Trace metal emissions from co-combustion of refuse derived and packaging derived fuels in a circulating fluidized bed boiler

Energy recovery from refuse derived fuels (RDF) and packaging derived fuels (PDF) is one option in integrated waste management. Nine RDF and PDF co-combustion tests with peat and coal in a circulating fluidized bed boiler were carried out in this work. Heavy metal emissions in flue gas and fly ash were measured. Multivariate data analyses were used to find out the most important parameters affecting metal emissions in the flue gas.

The results showed that total heavy metal emissions were low. Although RDF and PDF had more heavy metals than peat and coal, the multivariate data analysis showed that an increase of the RDF or PDF share in the fuel mixture up to 20% did not correlate directly with the metal emissions in the flue gas. Distribution of Cd, Cu, Zn and Sn between flue gas and fly ash correlated with each other. Injection of limestone to bind sulphur and chlorine did not have a significant effect on heavy metal emissions in the flue gas. Heavy metals concentrated on the fly ash, but all fly ashes passed the EPA-TCLP tests.     

Adsorption of arsenic(V) onto fly ash: a speciation-based approach

Arsenic (As) poses a significant water quality problem and challenge for the environmental engineers and scientists in the world. The large volume of coal fly ash produced around the world is a potentially significant anthropogenic source of arsenic. Currently the leaching behavior of arsenic from fly ash is not well understood. Batch methods were used in this study to investigate arsenic leaching using a raw ash, and arsenic adsorption using a clean, washed ash. Experimental results indicated that pH had a significant effect on arsenic leaching or adsorption. Between pH 3 and 7, less arsenic was in the dissolved phase. When pH was less than 3 or greater than 7, increasing amounts of arsenic were leached or desorbed from fly ash. The leaching and adsorption behavior of arsenic was interpreted with the speciation of surface sites and arsenic. In a new approach, a speciation-based model was developed to quantify the arsenic adsorption as a function of pH and surface acidity parameters. This work is important in offering insight into the leaching mechanism of arsenic from coal fly ash, and providing a robust model based upon specific, measurable parameters to quantify arsenic adsorption by other solid media in addition to fly ash.     

Polyelectrolyte enhanced ultrafiltration (PEUF) for the removal of Cd(II): effects of organic ligands and solution pH

This study focused on the effects of pH and organic ligands, namely ethylenediaminetetraacetic acid (EDTA), nitrilotriacetic acid (NTA), and citric acids, on the removal and recovery of Cd(II) in polyelectrolyte enhanced ultrafiltration (PEUF). Polyethylenimine (PEI), which can bind with both positively charged metal ions by coordination bonding and negatively charged ligand-metal complexes by charge attraction, was employed as a chelating polymer. The removal and recovery of Cd species was greatly dependent on the chemistry of organic ligands according to solution pH, particularly being related to the distribution of Cd-ligand complexes at different pH levels. In the presence of EDTA, the dominant Cd species are negatively charged Cd(EDTA)(2-) and CdH(EDTA)(-) over the range of pH levels investigated, interacting with PEI via electrostatic attraction and being less pH dependent. On the other hand, the pH effects of both NTA and citric acid systems are similar to that for the system without organic ligands. This was associated with the fact that free Cd ions were predominant at the acidic pH range in both NTA and citric acid systems.