活性炭纤维负载TiO_2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响.结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%.     

活性炭纤维负载TiO2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO₂作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO₂催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响。结果表明,活性炭纤维与TiO₂的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO₂溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37％;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%。     

泡沫镍负载改性TiO_2降解甲醛

为了消除甲醛气体对人类的危害,对甲醛气体的光催化降解行为进行了研究。采用沉淀-胶溶法制得了具可见光活性的纳米TiO2溶胶,然后将其负载于经过预处理的泡沫镍板上,置于自置的光催化反应器中,考察了在可见光照射下对密闭空间里面一定浓度的甲醛气体的降解情况。采用乙酰丙酮分光光度法,在最佳的检测条件下检测气相中甲醛气体经不同光照时间后的浓度。研究发现,负载了氮掺杂改性的TiO2的泡沫镍板在可见光照射下能够有效降解气相中的甲醛,反应240 min后对甲醛气体的降解率为93%;而同样条件下反应器中只有处理过的泡沫镍板时,甲醛气体浓度基本保持不变。     

纳米TiO2/活性炭复合光催化剂的制备及其对甲醛气体降解

研究了纳米TiO2/活性炭复合光催化剂对空气中典型污染气体甲醛的光催化降解特性。采用扫描电镜（SEM）表征复合催化剂的表面特征。结果显示,经改性后的纳米TiO2在复合催化剂表面分布均匀,呈球状。对甲醛气体的降解实验显示TiO2负载量为1%时对甲醛的去除效果最好,6 h去除率为61.7%。结果显示复合催化剂把甲醛气体分解成CO2,可以直接排空,无二次污染。     

纳米TiO2/活性炭复合光催化剂的制备及其对甲醛气体降解

研究了纳米TiO2/活性炭复合光催化剂对空气中典型污染气体甲醛的光催化降解特性。采用扫描电镜(SEM)表征复合催化剂的表面特征。结果显示,经改性后的纳米TiO2在复合催化剂表面分布均匀,呈球状。对甲醛气体的降解实验显示TiO2负载量为1%时对甲醛的去除效果最好,6 h去除率为61.7%。结果显示复合催化剂把甲醛气体分解成CO2,可以直接排空,无二次污染。     

TiO2光催化处理络合铜废水的实验研究

研究了以悬浮态TiO2为催化剂,在紫外光的作用下对络合铜废水进行光催化反应,分别考察了常温下TiO2投加量、反应时间、废水初始pH值、反应气氛等因素对处理效果的影响,并探讨了反应机理。结果表明：TiO2投加量为2 g/L,废水pH=4,300 W高压汞灯照射下,载入60 mL/min的空气反应40 min,120 mg/L EDTA络合铜废水的Cu（II）与COD的去除率达到最高,分别为96.56%和57.67%。     

TiO2光催化处理络合铜废水的实验研究

研究了以悬浮态TiO2为催化剂,在紫外光的作用下对络合铜废水进行光催化反应,分别考察了常温下TiO2投加量、反应时间、废水初始pH值、反应气氛等因素对处理效果的影响,并探讨了反应机理。结果表明:TiO2投加量为2 g/L,废水pH=4,300 W高压汞灯照射下,载入60 mL/min的空气反应40 min,120 mg/L EDTA络合铜废水的Cu(II)与COD的去除率达到最高,分别为96.56%和57.67%。     

负载TiO2/Fe^3＋的玻璃纤维反应器光催化苯酚

以玻璃纤维为载体,将TiO2负载到其表面形成了空间玻璃纤维反应器,引入Fe3＋作为掺杂改性离子,形成了负载TiO2/Fe^3＋的空间玻璃纤维光催化反应器,并以高压汞灯为光源进行了光催化降解水中苯酚的实验研究,考察了影响苯酚光催化降解的因素,确定了在UV365-250 W光源照射下,pH为3-5,O2通入量1.0 L/（min.L）,反应器内上升流速为0.7 m/min等实验条件下,初始浓度为30 mg/L的苯酚废水经120 min光催化反应后,降解率可达到85%,矿化率可达80%。     

负载TiO2/Fe3+的玻璃纤维反应器光催化苯酚

以玻璃纤维为载体,将TiO2负载到其表面形成了空间玻璃纤维反应器,引入Fe3+作为掺杂改性离子,形成了负载TiO2/Fe3+的空间玻璃纤维光催化反应器,并以高压汞灯为光源进行了光催化降解水中苯酚的实验研究,考察了影响苯酚光催化降解的因素,确定了在UV365～250 W光源照射下,pH为3～5,O2通入量1.0 L/(min.L),反应器内上升流速为0.7 m/min等实验条件下,初始浓度为30 mg/L的苯酚废水经120 min光催化反应后,降解率可达到85%,矿化率可达80%。     

活性炭负载Fe~(3+)催化H_2O_2氧化邻苯二甲酸二甲酯

将Fe3+负载在活性炭上制得载铁催化剂Fe/AC,并研究了该催化剂对邻苯二甲酸二甲酯(DMP)的催化降解性能。通过正交实验和单因素实验,探讨了催化剂投加量、H2O2投加量、溶液pH值和反应温度对水中DMP降解率的影响,同时对DMP矿化度进行了分析。实验结果表明,制得的载铁催化剂具有较高的催化活性;降解效果的影响顺序是反应温度催化剂投加量H2O2投加量溶液pH值;在反应温度为80℃、催化剂投加量为4 g/L、H2O2投加量为20 mL/L和溶液pH值为3的条件下反应120 min后,质量浓度为10 mg/L的DMP降解率最高可达97.73%;在优化的实验条件下反应150 min,DMP矿化度可达62.73%;催化剂反复使用5次仍具有较好的催化活性,DMP降解率仍可达到77%以上;反应过程中溶液Fe3+浓度的变化维持在1.07 mg/L左右,且可推测催化降解DMP主要是由非均相和均相催化氧化反应共同作用的。     

Trichloroethylene degradation by photocatalysis in annular flow and annulus fluidized bed photoreactors

The effects of trichloroethylene (TCE) gas flow rate, relative humidity, TiO(2) film thickness, and UV light intensity on photodegradation of TCE have been determined in an annular flow type photoreactor. Phosgene and dichloroacetyl chloride formation could be controlled as a function of TCE gas flow rate and photodegradation of TCE decreased with increasing relative humidity. The optimum thickness of TiO(2) film was found to be approximately 5 mum and the photocatalytic reaction rate of TCE increased with square root of UV light intensity. In addition, the effects of the initial TCE concentration, phase holdup ratio of gas and solid phases (epsilon(g)/epsilon(s)), CuO loading on the photodegradation of TCE have been determined in an annulus fluidized bed photoreactor. The TCE photodegradation decreased with increasing the initial TCE concentration. The optimum conditions of the phase holdup ratio (epsilon(g)/epsilon(s)) and CuO wt.% for the maximum photodegradation of TCE was found to be 2.1 and 1.1 wt.%, respectively. Therefore, an annulus fluidized bed photoreactor is an effective tool for TCE degradation over TiO(2)/silica gel with efficient utilization of photon energy.     

Photocatalytic oxidation of xenobiotics in water with immobilized TiO2 on agitator

A novel photocatalytic oxidation reactor, using Degussa P-25 TiO2 as a stationary phase with a thickness of 1.5-2.0 um on the blades of agitator, was developed to study the photocatalytic oxidation of xenobiotics. Particularly in this device, separation of photocatalyst from the purified water after oxidation reaction was not necessary, and no other aeration equipment was required to supply oxygen. To examine the efficiency of this device, photocatalytic degradation of xenobiotic organics such as carbofuran was studied as an example. Results indicated that carbofuran could be degraded completely with mineralization efficiency of 20% after 6 hours of oxidation under the imposed conditions. The mineralization rate of carbofuran was found to follow the pseudo-first order reaction kinetics. Moreover, the rate constant of mineralization was found to be proportional to TiO2 film area and the square root of UV light intensity. These results implied the mineralization efficiency of carbofuran could be improved through increasing TiO2 film area and UV light intensity. Accordingly, this novel device showed potential application for degrading xenobiotics in water.     

大尺寸大孔径TiO_2/SiO_2光催化剂的制备及甲醛去除研究

以大孔径SiO2为载体,通过钛酸丁酯溶液的浸渍、原位水解以及高温煅烧制备出大尺寸、大孔径的TiO2/SiO2光催化剂。利用自制空气净化装置对室内甲醛的清除进行研究,分别考察了TiO2的百分含量、紫外光光强、温度、湿度和空气流量等不同条件下TiO2/SiO2光催化剂对除去甲醛效率的影响。结果表明,反应温度从10～50℃依次升高,去除率逐渐下降。在相对湿度为50%,TiO2负载率为55.6%,流量为8 m3/h时,甲醛的最佳除去率达96.5%;经过7周时间的考察,发现TiO2/SiO2光催化剂的催化活性没有明显的下降。     

TiO2光催化涂料的制备及其降解甲醛研究

自制TiO2光催化涂料,重点对所制备的涂料在室内进行降解甲醛研究,考察了在不同分散剂、不同光催化剂以及不同甲醛初始浓度、不同光源、不同温度和不同湿度等环境因素下涂料对甲醛降解率的影响。结果表明,选用聚丙烯酸钠离子型分散剂,铜金属掺杂TiO2光催化剂制备的光催化涂料对甲醛降解率达80％以上且具有良好的耐久性,在室温（20℃左右）湿度50％日光灯照射下,甲醛初始浓度5μL时效果最佳。     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

镍网负载纳米TiO2光催化反应器对酸性品红脱色效果实验研究

采用负载纳米TiO2的三维镍网装配了光催化反应器,就其对酸性品红溶液进行脱色效果进行了实验研究。考察了反应器的3种装配条件、品红初始浓度、pH值、H2O2投加量、紫外光剂量等因素对酸性品红脱色效果的影响。结果表明：UV灯＋镍网＋TiO2模式组合的反应器脱色效果最好;在相同的处理时间内酸性品红溶液的脱色率随起始浓度的增大而减小;将酸性品红溶液pH值调至5时脱色效果最明显,70 min的脱色率可高达94.8%。脱色效果还可以通过溶液中添加H2O2和控制紫外线剂量来调节。当溶液中H2O2投加量为0.5 g/L时,处理70 min后的脱色率可高达98.3%;到达反应界面紫外光剂量越多则能够获得越高的酸性品红脱色率。