Use of vegetable oil in water emulsion achieved through ultrasonic atomization as cutting fluids in micro-milling

Significant amount of work is reported on development of vegetable oil based metalworking fluids (MWFs). Many also report on development and performance evaluation of vegetable based oils. For many of these water-based MWFs with vegetable oils, much effort is focused on stable emulsification of vegetable oil in water using a variety of surfactants. It has been found that surfactant-free stable emulsification of oil in water is possible through ultrasonic vibration. However, emulsification through ultrasonic atomization has not yet been considered, and the feasibility of emulsified metalworking fluids through ultrasonic atomization has not been investigated. In this paper, stable emulsification of vegetable oil in water has been achieved through ultrasonic atomization without using any surfactant. The emulsified vegetable oil in water is directly used to investigate its effectiveness as MWF in milling operations. Lower cutting forces, chip thickness, and burr amount are observed with vegetable oil-in-water emulsion compared to conventional MWF. The experimental results show strong potential for vegetable oil-in-water emulsion obtained through ultrasonic atomization as an effective MWF.     

Analytical model of metalworking fluid penetration into the flank contact zone in orthogonal cutting

Metalworking fluids (MWFs) are used widely in machining process to dissipate heat, lubricate moving surfaces, and clear chips. They have also been linked to a number of environmental and worker health problems. To reduce these impacts, minimum quantity lubrication (MQL) sprays of MWF delivered in air or CO₂ have been proposed. MQL sprays can achieve performance comparable with conventional water-based or straight oil MWFs while only delivering a small fraction of the fluid. This performance advantage could be explained by the enhanced penetration into the cutting zone that results from delivering MWF in high pressure and precise sprays. To explore this hypothesis, an analytical model of MWF penetration into the flank face of the cutting zone is developed and validated using experimental data. The model is based on a derivation of the Navier–Stokes equation and the Reynolds equation for lubrication and applied to an orthogonal cutting geometry under steady-state conditions. A solution to the model is obtained using a numerical strategy of discretizing the analytical scheme with two-dimensional centered finite difference method. Penetration into the cutting zone is estimated for MQL sprays delivered in air, CO₂ and N₂ as well as two conventional MWFs, straight oil and semi-synthetic emulsion. The model suggests that conventional MWFs, do not penetrate the cutting zone fully and fail to provide direct cooling to the flank zone where wear is most likely to occur. MQL sprays do penetrate the cutting zone completely. Using convective heat transfer coefficients from a previous study, a finite element heat balance is carried out on the tool to understand how each fluid impacts temperature near the flank tip of the tool. The results of the modeling effort are consistent with experimental measurements of tool temperature during turning of titanium (6AL4V) using a K313 carbide tool. The prediction of temperature near the flank indicates that MQL sprays do suppress temperatures near the flank effectively. These results help explain the low levels of tool wear observed for some MQL sprays, particularly those based on high pressure CO₂. This modeling framework provides valuable insight into how lubricant delivery characteristics such as speed, viscosity, and cutting zone geometry can impact lubricant penetration.     

Micro-flood (MF) technology for sustainable manufacturing operations that are coolant less and occupationally friendly

This paper presents a new technology for minimizing the use of metalworking fluids (MWFs) during the machining process that is atomization-less and occupational friendly. Micro-flood (MF) technology utilizes direct contact between the cutting tool and the MWF without the interaction of a gas medium. Experiments were conducted in high volume mass production environment turning HSLA (high strength low alloy) SAE 070Y steel. Machining performance and total air mass particulates were investigated in dry machining, Near dry machining (NDM) via atomized spray mist and MF technology. Open-atmosphere air monitoring indicated that total mass particulates behaved in an almost linear fashion with respect to gas atomization pressure, whereas the MWF flow rate demonstrated logarithmic trends in NDM applications using an atomized spray. Nozzle orientations directed upward into the air also produced higher mg/m³ concentrations (such as flank) than chip and rake face orientations that were directed down. Greater separation existed at higher gas atomization pressures, MWF flow rates and by changing the MWF type. At extreme limits, nozzle orientation affected mg/m³ concentration as much as 4–5 mg/m³ for water-miscible MWFs and 15–22 mg/m³ for non-water-miscible MWFs. Tool-life performance varied greatly among MWF type and flow rate, and in all cases MF technology performed better than NDM using an atomized spray mist. Direct and consistent MWF penetration to cutting zone using MF technology lowered tool-wear on the average of 12–75% compared to NDM at the same MWF flow rate. Compared to dry machining, NDM improved tool-wear on the average by 20–243%. In one case, tool-wear performance was improved by 616% at 0.15 mm using MF technology compared to dry machining at a nominal 0.925 mm tool-wear. Overall, a large mass reduction of particulates can be achieved employing MF technology that would have been unrealistic for an open-atmosphere machining environment employing an atomized spray mist. On the average, MF technology can maintain a total air mass particulate of less than 0.4 mg/m³ in the occupational work zone using MWF flow rates up to 1260 ml/h, regardless of the MWF classification. Atomized spray mist applications are capable meeting the 5 mg/m³ OSHA limit if MWF flow rates are less than 160 ml/h, air pressures are less than 0.137 MPa (20 psi) using water-miscible MWFs and air pressures are less than 0.0344 MPa (5 psi) using non-water-miscible MWFs.     

Evaluation of vegetable based cutting fluids with extreme pressure and cutting parameters in turning of AISI 304L by Taguchi method

Many problems such as health and environment issues are identified with the use of cutting fluids (CFs). There has been a high demand for developing new environmentally friendly CFs such as vegetable based cutting fluids (VBCFs) to reduce these harmful effects. In this study, performances of six CFs, four different VBCFs from sunflower and canola oils with different ratios of extreme pressure (EP) additives, and two commercial types of CFs (semi-synthetic and mineral) are evaluated for reducing of surface roughness, and cutting and feed forces during turning of AISI 304L austenitic stainless steel with carbide insert tool. Taguchi’s mixed level parameter design (L₁₈) is used for the experimental design. Cutting fluid, spindle speed, feed rate and depth of cut are considered as machining parameters. Regression analyses are applied to predict surface roughness, and cutting and feed forces. ANOVA is used to determine effects of the machining parameters and CFs on surface roughness, cutting and feed forces. In turning of AISI 304L, effects of feed rate and depth of cut are found to be more effective than CFs and spindle speed on reducing forces and improving the surface finish. Performances of VBCFs and commercial CFs are also compared and results generally show that sunflower and canola based CFs perform better than the others.     

Cryogenic Machining of Tantalum

A new approach for the machining of tantalum is presented. The new approach is a combination of traditional turning and cryogenically enhanced machining (CEM). In the tests, CEM was used to reduce the temperature at the cutting tool/workpiece interface, and thus reduce the temperature-dependent tool wear to prolong cutting tool life. The new method resulted in a reduction of surface roughness of the tantalum workpiece by 200% and a decrease of cutting forces by approximately 60% in experiments. Moreover, cutting tool life was extended up to 300% over that in the conventional machining.     

Effect of fluid concentration in titanium machining with an atomization-based cutting fluid (ACF) spray system

The aim of this work is to investigate the effect of metal-working fluid (MWF) concentration on the machining responses including tool life and wear, cutting force, friction coefficient, chip morphology, and surface roughness during the machining of titanium with the use of the ACF spray system. Five different concentrations from 5 to 15% of a water-soluble metalworking fluid (MWF) were applied during turning of a titanium alloy, Ti–6Al–4V. The thermo-physical properties such as viscosity, surface tension and thermal conductivity of these concentrations were also measured. The test results demonstrate that the tool life first extends with the increase in MWF concentration and then drops with further increase. At low concentration (e.g., 5%), a lack of the lubrication effect causes to increase in a higher friction at the tool–chip interface resulting in severe chipping and tool nose/flank wear within a short machining time. On the other hand, at high concentration, the cooling effect is less. This increases cutting temperature and a faster thermal softening/chipping/notching of the tool material and higher friction at the tool–chip–workpiece interaction zones resulting in early tool failure. A good balance between the cooling and the lubrication effects seems to be found at the 10% MWF concentration as it offers the best machining performance. However, machining with flood coolant is observed to perform the best in the range of 5–7%.     

Experimental investigation of turning AISI 1045 steel using cryogenic carbon dioxide as the cutting fluid

The intensive temperatures in high speed machining not only limit the tool life but also impair the machined surface by inducing tensile residual stresses, microcracks and thermal damage. This problem can be handled largely by reducing the cutting temperature. When the conventional coolant is applied to the cutting zone, it fails to remove the extent of the heat effectively. Hence, a cryogenic coolant is highly recommended for this purpose. In this paper, an attempt has been made to use cryogenic carbon dioxide (CO₂) as the cutting fluid. Experimental investigations are carried out by turning AISI 1045 steel in which the efficiency of cryogenic CO₂ is compared to that of dry and wet machining with respect to cutting temperature, cutting forces, chip disposal and surface roughness. The experimental results show that the application of cryogenic CO₂ as the cutting fluid is an efficient coolant for the turning operation as it reduced the cutting temperature by 5%–22% when compared with conventional machining.It is also observed that the surface finish is improved to an appreciable amount in the finished work piece on the application of cryogenic CO₂. The surface finish is improved by 5%–25% in the cryogenic condition compared with wet machining.     

Laser tempering based turning process for efficient machining of hardened AISI 52100 steel

Cost-effective machining of hardened steel components such as a large wind turbine bearing has traditionally posed a significant challenge. This paper presents an approach to machine hardened steel parts efficiently at higher material removal rates and lower tooling cost. The approach involves a two-step process consisting of laser tempering of the hardened workpiece surface followed by conventional machining at higher material removal rates with lower cost ceramic tools to efficiently remove the tempered material. The laser scanning parameters that yield the highest depth of tempered layer are obtained from a kinetic phase change model. Machining experiments are performed to demonstrate the possibility of higher material removal rates and improved tool wear behavior compared to the conventional hard turning process. Tool wear performance, cutting forces, and surface finish of Cubic Boron Nitride (CBN) tools as well as low cost ceramic tools are compared in machining of hardened AISI 52100 steel (~63 HRC). In addition, cutting forces and surface finish are compared for the laser tempering based turning and conventional hard turning processes. Experimental results show the potential benefits of the laser tempering based turning process over the conventional hard turning process.     

UV-Fenton法降解金属切削液废水及数学模型的建立

采用UV/Fenton法处理金属切削液废水,通过正交试验和单因素试验得到其最佳工作条件为pH=2.5、H2O2(浓度30%)投加量=127.5 mL/L、Fe2+投加量=24.8 mmoL/L、总反应时间=2 h、投加次数6次,此条件下金属切削液废水COD去除率可达到94.4%;并采用1stOpt软件对正交试验数据和单因素模型方程进行多元非线性拟合,建立了UV/Fenton法处理金属切削液废水COD降解率的数学模型方程,模型结论与正交试验结果一致,表明该模型可以正确地反映UV/Fenton法处理金属切削液废水的降解效果。     

Process capability study of laser assisted micro milling of a hard-to-machine material

Laser assisted micro milling (LAMM) is capable of generating three-dimensional micro scale features in hard-to-machine materials. This paper compares the process capability of LAMM with conventional micro milling of a hardened tool steel. In particular, the potential advantages of LAMM over micro milling with respect to cutting forces, tool wear, material removal rate, burr formation and surface roughness are investigated when micro milling hardened A2 tool steel (62 HRC). The results show that LAMM has significant advantages over micro milling, especially in terms of cutting forces, material removal rate and tool wear. The average reduction in the resultant cutting force is found to be up to 69% with laser assist. In addition, tool wear is found to be substantially less with laser assist even when the material removal rates are increased by a factor of six over the tool manufacturer recommended cutting conditions.     

Ball end milling mechanistic model based on a voxel-based geometric representation and a ray casting technique

Prediction of machining forces involved in complex geometry can be valuable information for machine shops. This paper presents a mechanistic cutting force simulation model for ball end milling processes, using ray casting and voxel representation methods used in 3D computer graphics field. Using this method, instantaneous uncut chip cross sectional areas can be extracted, which can be used in cutting pressure coefficient extraction and machining simulation including machining forces and geometry of the workpiece. The major advantage of the proposed scheme is that it can simulate milling processes with arbitrary cutting tool geometry on a workpiece with complex geometry, using an algorithm with constant time complexity. A series of cutting experiments were carried out to validate the model.     

Tool wear of coated drills in drilling CFRP

This study aimed to investigate the wear of certain coated drills when drilling carbon fiber reinforced composites (CFRP). Three different drills were used in the drilling experiments: uncoated, diamond coated and AlTiN coated carbide (WC–Co) drills. The tool wear in CFRP machining was quite different from that in conventional metal machining. The primary wear type was a dulling or blunting of the cutting edge, which has been referred to as edge rounding wear or edge recession. In this paper, a hypothesis has been developed to explain the edge rounding wear in CFRP machining. Due to the fracture-based chip formation of CFRP, there is lack of the work material stagnation zone in front of the cutting edge, which normally prevents the edge wear in metal machining. Series of wear lead to rapid dulling of the cutting edge. The resistance to edge rounding wear on the coated as well as uncoated drills has been investigated. The diamond coating significantly reduces the edge rounding wear. However, AlTiN coated drills showed no visible improvement over the uncoated carbide drill, despite of their high hardness, thus not protecting the drill. The wear mechanisms of the uncoated carbide drill and coatings are discussed. It is believed that the 2-body and 3-body abrasive wear fail to explain the observed tool wear in CFRP drilling. However, the wear of the coatings and uncoated carbide substrate from tribo-meter tests correlated well with the tool wear in the CFRP drilling. Therefore, the tribo-meter test can be used to screen the prospective tool materials before carrying drilling experiment.     

An Approach to Theoretical Modeling and Simulation of Face Milling Forces

A new approach to theoretical modeling and simulation of face milling forces is presented. The present approach is based on a predictive machining theory in which machining characteristic factors in continuous cutting with a single-point cutting tool can be predicted from the workpiece material properties, tool geometry, and cutting conditions. The action of a milling cutter is considered as the simultaneous work of a number of single-point cutting tools, and the milling forces are predicted from input data of workpiece material properties, cutter parameters and tooth geometry, cutting condition, cutter and workpiece vibration structure parameters, and types of milling. A predictive force model for face milling is developed using this approach. In the model, the workpiece material properties are considered as functions of strain, strain rate, and temperature. The ratio of cutter tooth engagement over milling is taken into account for the determination of temperature in the cutting region. Cutter runout is included in the modeling for the chip load. The relative displacement between the cutter and workpiece due to the cutter and workpiece vibration is also included in the modeling to consider the effect on the undeformed chip thickness. A milling force simulation system has been developed using the model, and face milling experimental tests have been conducted to verify the simulation system. It is shown that the simulation results agree well with experimental results.     

Experimental Evaluation of Cutter Orientation When Ball Nose End Milling Inconel 718™

High-speed machining (HSM), specifically end milling and ball end cutting, is attracting interest in the aerospace industry for the machining of complex 3D aerofoil surfaces in titanium alloys and nickel-based superalloys. Following a brief introduction on HSM and related aerospace work, the paper reviews published data on the effect of cutter/workpiece orientation, also known as engagement or tilt angle, on tool performance. Such angles are defined as ±β_fN and ±β_f.Experimental work is detailed on the effect of cutter orientation on tool life, cutting forces, chip formation, specific force, and workpiece surface roughness when high-speed ball end milling Inconel 718™. Dry cutting was performed using 8 mm diameter PVD-coated solid carbide cutters with the workpiece mounted at an angle of 45° from the cutter axis.A horizontal downward (-β_fN) cutting orientation provided the best tool life with cut lengths ∼50% longer than for all other directions (+β_fN, +β_f, and –β_f). Evaluation of cutting forces and associated spectrum analysis of results indicated that cutters employed in a horizontal downward direction produced the least vibration. This contributed to improved workpiece surface roughness, with typical mean values of ∼0.4 μm Ra as opposed to ∼1.25 μm Ra when machining in the vertical downward (–β_f) direction.     

Evaluation of near-dry machining effects on gear milling process efficiency

One of the main environmental pollution sources related to machine building industry is the huge amount of cutting fluids which are supplied during the machining processes. In order to avoid the problems induced by cutting fluids' usage, considerable progress has been recently made in the field of near-dry machining (NDM). Converting conventional processes to minimal quantity lubrication (MQL) methods imposes new tasks' classification within the tribiological system in order to guarantee the process safety and product quality. This paper gives an overview on some requirements to be considered for a successful MQL application into industrial practice. Its last part is focused on the evaluation of NDM effects on the gear milling process efficiency, with respect to hob wear, surface quality, cooling effect, and environment protection.     

Machining Performance and Health Effects of Cutting Fluid Application in Drilling of A390.0 Cast Aluminum Alloy

Environmental issues in machining have led to a push to curtail the use of cutting fluids. However, cutting fluid effects on part quality, process planning, and operator exposure to aerosols need to be first studied. The effects of cutting fluid application on hole accuracy and mist generation have been studied for blind-hole drilling of A390.0 aluminum alloy. Different cutting fluid types and application modes were tested under varying conditions of cutting speed, feed, and hole depth. The cooling and chip-transporting ability of cutting fluids was found to have the maximum effect on dimensional accuracy. Dry cutting yielded holes with the least accuracy, while mist lubrication was found to give superior dimensional accuracy to dry cutting but had the worst aerosol concentration. Flooding with synthetic cutting fluid gave the best overall results.     

Measurement of tool internal temperatures in the tool–chip contact region by embedded micro thin film thermocouples

Sensors capable of providing fast and reliable feedback signals for monitoring and control of existing and emerging machining processes are an important research topic, that has quickly gained academic and industrial interest in recent years. Generally, high-precision machining processes are very sensitive to variation in local machining conditions at the tool–workpiece interface and lack a thorough understanding of fundamental thermomechanical phenomena. Existing sensors to monitor the machining conditions are not suitable for robust in-process control as they are either destructively embedded and/or do not possess the necessary spatial and temporal resolution to monitor local tool internal temperatures during machining at the cutting tip/edge effectively. This paper presents a novel approach for assessing transient tool internal temperature fields in the close vicinity of less than 300 μm of the tool cutting edge. A revised array layout of 10 micro thin film micro thermocouples, fabricated using adapted semiconductor microfabrication methods, has been embedded into polycrystalline cubic boron nitride (PCBN) cutting inserts by means of a modified diffusion bonding technique. Scanning electron microscopy was used to examine material interactions at the bonding interface and to determine optimal bonding parameters. Sensor performance was statically and dynamically characterized. They show good linearity, sensitivity and very fast response time. Initial machining tests on aluminum alloys are described herein. The tests have been performed to demonstrate the functionality and reliability of tool embedded thin film sensors, and are part of a feasibility study with the ultimate goal of applying the instrumented insert in hard machining operations. The microsensor array was used for the acquisition of tool internal temperature profiles very close to the cutting tip. The influence of varying cutting parameters on transient tool internal temperature profiles was measured and discussed. With further study, the described instrumented cutting inserts could provide more valuable insight into the process physics and could improve various aspects of machining processes, e.g. reliability, tool life, and workpiece quality.     

Prediction of polycrystalline materials texture evolution in machining via Viscoplastic Self-Consistent modeling

The crystallographic orientation or anisotropy is one of the main microstructural attributes strongly affecting the mechanical properties of materials. It is also an influential parameter to be considered during the manufacturing process especially for ultra-precision machining since it affects part quality, tool performance, and process productivity through material properties. In this study, a prediction toolset constituted of a Viscoplastic Self-Consistent model and machining process mechanics model is used to predict the texture evolution on the machined surface. The VPSC (Viscoplastic Self-Consistent) methodology which uses the mechanisms of slip and twinning that are active in single crystals of arbitrary symmetry was used. For this, an analytical model for the process mechanics is derived to understand the forces and stresses generated by the cutting tool at each workpiece point, then the strain and strain rate to capture the rate at which the material is deforming and finally the crystallographic orientations under various machining conditions. Experiments were performed on the orthogonal cutting of aluminum alloy AA-7075-T651 and the texture results were compared to model predictions.     

Orthogonal machining of single-crystal and coarse-grained aluminum

Orthogonal machining of single-crystal and coarse-grained (i.e., grain size considerably larger than the uncut chip thickness) materials has been a subject to many studies in the literature. The first part of this paper presents background on machining single-crystal materials, including experimental and modeling attempts. The second part briefly describes more recent modeling results from the authors, and presents new experimental results on planing and plunge-turning of single-crystal and coarse-grained aluminum using diamond tools. The experiments indicate that (1) cutting across grains of a coarse-grained aluminum workpiece produces distinctly varying forces and surface roughness from one grain to another, (2) plunge-turning and planing of single crystal aluminum provide equivalent force data for large rake angles, (3) forces alter between two distinct levels while cutting single crystals with small rake angles, and (4) with small rake angles, subsurface damage on single-crystal aluminum is extensive, reaching depths comparable to the uncut chip thickness.     

Application of FEM simulation of chip formation to stability analysis in orthogonal cutting process

Models for chatter prediction in machining often use a mechanistic force model that calculate the force as the product of a material dependent cutting constant and chip area. However, in reality, the forces are the result of complex interaction between the tool and the chip, and are affected by many factors. The effects of these complex, and often nonlinear, factors on the machining dynamics may only be included in chatter prediction if the chip formation process is simulated concurrently with simulation of the machining dynamics. In this paper, finite element simulation of the chip formation process is combined with simulation of chatter dynamics and the inter-relationship between the chip formation process and the chatter phenomenon is investigated. Mesh adaptation technique is used to simulate the chip formation within an FEM elastoplastic analysis with dynamic effects and frictional contact. The combined modeling predicts the occurrence of process damping at low cutting speeds, which other models are generally unable to predict.