微电解-催化氧化-吸附法处理二硝基苯废水

二硝基苯生产废水具有硝基苯类化合物浓度高,盐量高,难降解等特点.CODCr的平均质量浓度为10 g/L,含盐量达30 g/L.采用微电解-催化氧化-吸附法对该废水进行处理.结果表明:经微电解处理后硝基苯类物质的去除率可达90%以上,铁碳还原后的废水再经催化氧化和活性炭吸附后,废水的CODCr去除率达到96%,硝基苯类物质、色度的去除率接近100%,出水可达到<污水综合排放标准>(GB8978-1996)规定的三级排放标准,是一种效果良好的二硝基苯类废水的处理方法.     

微电解法对高浓度染料废水的脱色作用研究

以难生化降解的甲基橙为实验染料,采用铁碳微电解法对高浓度染料废水脱色进行模拟实验.主要研究了水力停留时间(HRT)、温度和pH值对色度去除率的影响和铁碳床的再生条件.室温(20℃)条件下,最佳实验条件为:HRT=30 min,pH=5-6,铁碳床运行周期为20 h.废水温度提高有利于提高脱色效果.实验结果表明,400mg/L的甲基橙实验水样,在最佳实验条件下经过微电解法处理,色度去除率可达85%以上,CODCr去除率达到30%左右.在相同实验条件下,铁碳微电解法处理混合染料废水,色度去除率降低到64.7%.铁碳床运行失效后,用6%～8%的稀硫酸循环再生1 h,可继续使用,运行效果良好,但运行周期有所缩短.     

一种处理高浓度含盐废水的新工艺

针对目前化工、染料、制药等行业高浓度含盐废水难处理的现状,以某化工厂为实例,介绍了一种新工艺即"NACE"工艺在处理高浓度含盐废水中的应用。并与反渗透方法进行优势对比分析,结果表明:"NACE"工艺具有运行成本低、抗污染、处理效果稳定等优点,在实践中可以到很好的应用。     

曝气生物滤池深度处理部分制药废水的研究

本文以曝气生物滤池深度处理制药废水的二级生化出水.研究了曝气生物滤池的启动及气水比、水力负荷和进水有机物浓度对曝气生物滤池CODCr去除率的影响,并最终选出一种最优质高效的生物滤料.试验结果表明,CODCr去除率与水力负荷和气水比并不是简单的线性关系.在气水比为15,水力停留时间为4 h时,CODCr去除率最大.进水有机物质量浓度处于323～1 021 mg/L范围内,CODCr去除率随进水有机物质量浓度的增加而增加.     

Fenton法对合成制药废水的预处理试验研究

采用Fenton法对某合成制药废水进行了预处理试验研究,考察H2O2、Fe2+投加量及反应时间对废水CODCr、色度、NH4+-N去除效果的影响,重点分析了反应体系中有毒难降解有机污染物的变化情况。结果表明,当H2O2(30%)投加量为2%(体积分数),FeSO4.7H2O投加量为400mg/L,反应时间为60min时,废水CODCr、色度的去除率分别为67.73%和40.05%。通过GC-MS分析发现,该废水中含有多种脂类和苯环类等难降解有机污染物质,Fenton反应过程中出现了醇、酯、有机酸等较易降解的中间产物,随着反应的进行废水中苯环类、脂类等大分子有毒有机物得到大幅削减,废水的生物毒性大大降低,BOD/COD值由0.18上升至0.48,可生化性明显提高。     

复合混凝剂处理模拟酸性大红染料废水的研究

通过单一混凝剂的筛选与混凝剂间的复合方法,配制了FeSO4-MgSO4Ca(OH)2-PAM复合混凝剂.采用该混凝剂对CODCr值为288.3 mg/L、色度为25 000倍的模拟酸性大红GR染料废水进行试验研究,通过改变各药剂投加次序、搅拌与沉降时间以及投加方式等,确定了取得最佳处理效果时的优化操作条件为FeSO4-MgSO4-Ca(OH)2-PAM配比(质量比)=100∶200∶150∶(0.047～0.093),pH=9.5～10.0.试验结果为CODCr去除率最高可达85.3%,当复合混凝剂投加量为1.5～2.25 g/L时,脱色率最高可达97.5%,其处理效果明显优于单一混凝剂; 当脱色率达90%时,药剂成本为1.12元/T废水,结果表明,该复合方案从成本和处理效果方面考虑均是可行的.     

铁炭微电解处理制药废水效能影响因素研究

针对麻醉原料制药废水有机物浓度高、可生化性差、毒性大等特点,采用铁炭微电解法作为处理该制药废水的预处理工艺、考察了填料粒度、pH值、铁炭比、气水比和负荷等因素对铁炭微电解系统处理效能的影响.结果表明,在进水pH值为3,Fe/C体积比为1:2,铁屑、活性炭粒径为1 mm,负荷为175.5 kgCOD/(m3铁炭·d),气水比为10:1,反应时间为2h时,可使进水COD、色度分别为19000mg/L及600的制药废水,出水降至8 490 mg/L及20,去除率分别为55.29％和96.67％,同时可使废水可生化性得到增大,BOD5/COD由进水0.14提高至出水0.56.     

复合絮凝剂XG用于工业废水的处理

利用自制的复合絮凝剂 XG处理多种工业废水 ,研究了废水处理工艺过程和处理条件对絮凝剂处理废水效果的影响。实验结果表明 ,XG应用于造纸、毛巾厂、化工等工业废水处理 ,CODCr去除率达 75%～ 80 % ,脱色率 >80 % ,处理操作工艺简单 ,成本低 ,处理效果优于聚合氯化铝。     

养猪废水的吸附-过滤法初级处理试验研究

以实际养猪废水为对象,采用吸附-过滤法进行预处理,研究稻草滤料和稻草-沸石双层滤料在不同滤速下对养猪废水中CODCr、氨氮和磷的去除效果.结果表明,稻草-沸石双层滤料对CODCr、氨氮和磷的去除效果明显优于稻草滤料.以稻草-沸石双层滤料为过滤介质时,5 m/h的滤速下,CODCr、氨氮和磷的最大去除率分别达47 9%、72 9%和50 1%.研究表明,吸附-过滤预处理不仅能去除养猪废水中的CODCr、氨氮和磷,还能去除一定量的小分子有机物和臭味,同时附着大量固体有机物的稻草和吸附有氨氮、磷的沸石经过处理后可作为土壤改良剂或肥料,从而实现了农业固体废物的资源化利用.     

超声/Fenton法处理三氯吡啶醇钠废水工艺优化及机理初探

采用超声/Fenton技术处理三氯吡啶醇钠生产过程中产生的高浓度有机废水。通过正交试验确定超声/Fenton氧化最佳操作参数为H2O2投加量0.7 mol/L、Fe2+投加量1.39 g/L、反应时间90 min,此时COD降解率达95.3%。结果表明,Fe2+投加量是影响CODCr去除率最主要的因素。结合气相色谱-质谱联用仪检测,分析了超声/Fenton反应前后产物,初步探讨了超声/Fenton氧化法处理三氯吡啶醇钠废水的反应历程:在·OH作用下,氯苯与苯环转化为氯乙烯等小分子物质;氯乙烯发生加氢反应,进而转化为氯乙烷、氯甲烷。氯原子能够被·OH氧化为Cl·,并通过氢原子取代反应,将氯乙烯转化为1,1-二氯乙烯。     

油浸变压器排油注氮装置在500kV变电站的设计与应用

在分析500kV变电站主变压器消防系统的现状,比较3类消防系统优缺点的基础上,详细论述了主变排油注氮装置的结构组成、工作原理、参数计算、控制系统设计以及需要注意的事项等,为下一步排油注氮装置的推广应用打下基础.     

HAZOP结合What-if方法在某延迟焦化装置除焦中的应用

为克服传统危险与可操作性（HAZOP）定性分析方法在复杂操作、间歇作业等过程中使用的局限性,提出在传统HAZOP定性分析方法的基础上结合What-if（故障假设）方法,对人的不安全行为和操作规程不完备所导致的风险后果分析作出补充。详细说明其技术原理、工作流程等使用细节,系统阐述该方法与传统HAZOP定性分析方法的区别,并在某延迟焦化装置的除焦操作的风险分析中应用。经分析,识别出在“给水-泡焦”节点,有“操作规程错误”场景2项,“操作规程不具体”场景1项,不存在“操作人员未按操作规程执行”场景。研究结果表明:本文方法有效且具有较好效果,可以广泛应用于操作规程/作业指导书审查、作业过程隐患排查等方面,帮助企业开展操作层面的风险识别与管理,提升企业的生产安全水平。     

Nighttime pedestrian fatalities: A comprehensive examination of infrastructure,user, vehicle,and situational factors

Introduction: Pedestrian fatalities in the United States increased 45.5% between 2009 and 2017. More than 85% of those additional pedestrian fatalities occurred at night. Method: We examine Fatality Analysis Reporting System (FARS) data for fatal pedestrian crashes that occurred in the dark between 2002 and 2017. Within-variable and before/after examinations of crashes in terms of infrastructure, user, vehicle, and situational characteristics are performed with one-way analysis of variance (ANOVA) and two-sample t-tests. We model changes in crash characteristic proportions between 2002–2009 and 2010–2017 using linear regressions and test for autocorrelation with Breusch-Godfrey tests. Results: The increase in fatal nighttime pedestrian crashes is most strongly correlated with infrastructure factors: non-intersection unmarked locations (saw 80.8% of additional fatalities); 40–45 mph roads (54.6%); five-lane roads (40.7%); urban (99.7%); and arterials (81.1%). In addition, SUVs were involved in 39.7% of additional fatalities, overrepresenting their share of the fleet. Increased pedestrian alcohol and drug involvement warrant further investigation. The age of pedestrians killed increased more (18.1%) than the national average (3.2%). Conclusions: By identifying factors related to the increase in nighttime pedestrian fatalities, this work constitutes a vital first step in making our streets safer for pedestrians. Practical Applications: More research is needed to understand the efficacy of different solutions, but this paper provides guidance for such future research. Engineering solutions such as road diets or traffic calming may be used to improve identified infrastructure issues by reducing vehicle speeds and road widths. Rethinking vehicle design, especially high front profiles, may improve vehicle issues. However, the problems giving rise to these pedestrian fatalities are likely a result of not only engineering issues but also interrelated social and political factors. Solutions may be correspondingly comprehensive, employing non-linear, systems-based approaches such as Safe Systems.     

森林地表火蔓延模拟方法及其计算机实现

进行了森林火蔓延的研究,对传统的经验公式和模型进行改进,明显发现改进的模型有更好的结果,用计算机巧妙准确地实现了模拟模型,在风力不是特别大,地形变化不是特别剧烈时,该模型有较高精度;并结合火蔓延的主要因素（气象因子、气候、地形等）,进行系统分析,写出算地,编制实现地表火蔓延的预测预报计算机系统软件。这对于有效的组织扑救、减少火灾损失、计算森林火灾的损失评估有重要意义。     

潞安矿区煤层渗透率的各向异性特征实验研究

为了研究原位煤体渗透性的各向异性特征,以山西潞安常村矿3号煤层圆柱试样为对象,利用TCQT-Ⅲ型低渗煤层气相驱替增产试验装置,对煤样进行加载,并以氮气注入压力2.0 MPa的条件下,分析垂直层理和平行层理2个方向的煤体变形和渗透率变化特征。实验结果表明:煤样在加载过程中,平行和垂直层理煤样渗透率均随着有效应力的增大而减小,平行层理方向的渗透率始终大于垂直层理方向,应力加载初期渗透率急剧下降,最后逐渐趋于平缓;径向应变的增加量与渗透率呈正相关性,且平行层理相关性大于垂直层理;沿平行层理方向的裂隙度大于沿垂直层理方向,沿垂直层理方向的应变量大于沿平行层理方向;应变增加量均随有效应力的增加而逐渐减小。研究结果可为煤层井网布置及优化提供参考。     

Footedness and Mounting—Short Review and Two Case Studies

Footedness is a personal quality like handedness. Footedness may be associated with moving ability during mounting, dismounting, and jumping movements. Occupational accidents have occurred during movement at different working levels, during the use of access and exit systems, and during the mounting of vehicles. Aging can also affect accident risk and body laterality. For example, falling accidents on stairs are common among the elderly. One reason for accidents may be that the structure of the access system or stair system is unsuitable for individual moving patterns depending partly on body laterality. Footedness and the way the feet are used may be contradictory to the demands of the moving situation, especially during uncommon or rapid situations. This contradiction may trigger disturbance during moving. The aims of this pilot study were (a) to review the literature briefly and (b) to describe the use of the dominant and nondominant foot by farmers and the elderly when mounting a tractor and stairs, respectively. The study also gives ideas for future studies based on both (a) and (b).     

AHP与GA-SVM耦合模型在滑坡预警中的应用*

为了减少滑坡造成的损失,提高滑坡预测的准确性,通过搭建灾害模拟平台获得滑坡的实验数据,在获得多组模拟实验数据后,分析各变量的特性。首先,通过层次分析(Analytic Hierarchy Process,AHP)算法,对滑坡进行危险度划分;然后,通过支持向量机(Support Vector Machine,SVM)建立模型,遗传算法(Genetic Algorithm,GA)再优化SVM参数,提出1种层次分析法与GA-SVM相耦合的模型。研究结果表明:AHP方法划分后的数据,通过GA与SVM结合建立的模型精度较好,实验预测结果与实际结果较为吻合,与单一SVM相比,精度更高,结果更好,更加适用于多变量的复杂非线性滑坡预警。     

一起有机过氧化物爆炸事故的调查和分析

阐述一起重大爆炸伤亡事故的现场调查和原因分析，介绍如何通过人证物证材料，用鱼刺图法找出可能引起事故的诸原因，逐项加以分析，将与人证或物证材料相矛盾的原因子以排除，最后剩下无法排除亦即能与人证物证相符的那个原因，就是事故的真正原因。笔者是这起事故调查专家组组长，取证和数据可靠。     

Debunking the false dichotomy of leadership idealism and pragmatism: Critical evaluation and support of newer genre leadership theories

Leadership theories have shifted over the last few decades from a focus on managerial functions and economic leader–follower exchanges toward greater focus on the interpersonal dynamics occurring within the leadership process. Theories such as transformational, ethical, authentic, and other “newer genre” theories were created to address neglected topics such as leader vision and inspirational messages, transparency, emotional effects, morality, individualized attention, and intellectual stimulation. Critiques of these theories, however, have been raised. In this paper, we address five of those critiques and argue for the validity and practical effectiveness of the new genre theories. Further, we describe how newer genre leadership research should be viewed as a performative epistemology, entailing a process of co‐creation involving scholars and practitioners. Finally, from this view, we provide general ideas for leader development. Copyright © 2014 John Wiley & Sons, Ltd.     

Occupational Safety and Health in Finland

In Finland, occupational safety is the responsibility of the employer, while the occupational safety and health laws are enforced by the Labour Inspection Service, an organization of the state. The Labour Inspection is divided in 11 administrative districts, and it employs 360 professionals. They are mandated to carry out site visits without prearranged appointments to inspect safe work situations, working hours, construction safety, or any aspect of accident risks. The inspectors are also mandated to verify the existence of sufficient occupational health services as prescribed by the Occupational Health Services Act for all employees. The occupational health services are typically provided by enterprise-owned medical departments, by mutually owned health care centers, by private practitioners, or by municipal health care centers. The latter are required by law to provide all services as prescribed by the legislation to anyone who comes to the facility. This situation is prevalent in the countryside, where there are very few private caregiving centers. Declaring occupational accidents and disease cases is mandatory, and the Inspection districts examine all accidents to establish causes and consequences, and to initiate prosecution in case of criminal negligence. Labour Inspection Districts are also notified of the new occupational disease cases as they are declared to insurance companies. Insurance for occupational disease, accidents, and death is an obligation of the employer, although they can choose the insurance company. The medical confidentiality between the workers and their occupational health care providers is very strict. Official statistics are maintained by the state Statistics Finland organization, and they may be used, for example, for research purposes by scientific institutes like the Finnish Institute of Occupational Health. Construction industry accounts for 25% of all fatal accidents (120 cases per 1 million working hours), followed by mechanical, wood, metal, machinery, and pulp and paper industry (10% each of fatal accidents) with rates ranging from 100–160 cases per 1 million working hours. There are some 5,000 occupational disease cases per year (rate 22/10,000 employed). The major disease categories include repetitive strain injuries (1,300 cases), respiratory allergies (600 cases), occupational skin diseases (1,000 cases), and 900 cases of noise-caused hearing loss. In 1998, 589 cases of asbestos-related diseases were reported.