活性炭纤维基催化剂在烟气脱硝中的应用

以活性炭纤维（ACF）为载体的催化剂具有良好的脱硝性能,材料、负载方式、负载量、活性组分等的不同都会对NOx的脱除率有很大的影响。在目前研究中,活性炭纤维基催化剂主要应用于催化分解法和选择性催化还原法（SCR）。本文介绍了活性炭纤维的基本特性,比较了不同催化剂的脱硝性能,并在此基础上提出了今后的研究方向。     

糠醛渣球形炭的制备及脱硫性能

以糠醛渣为原料,配以一定比例的粘合剂制备出球形活性炭(SAC-F).比较了SAC-F与活性炭纤维(ACF)和粒状活性炭(GAC-C)的流体力学性能,初步探讨了直径为4～5mm SAC-F的制备参数,考察了它的碘吸附值和对模拟烟气中SO2的脱除性能,以及物理和表面化学性质.结果表明,在相同的装填高度下,随着空速的增加,SAC-F上压降增加得最慢,ACF的增加速率是它的6～7倍,GAC-C是它的1～2倍;虽然SAC-F比GAC-C的比表面积和孔容都小,但其平均脱硫率为87%,明显优于GAC-C,与GAC-C相比,SAC-F表面含有较少的C-O.     

活性炭纤维及其在环境保护领域中的应用

活性炭纤维 (ACF)是一种新型高效吸附剂 ,与颗粒活性炭 (GAC)相比 ,它具有比表面积大 ,吸附速度快 ,吸附容量大等等特点。本文介绍了活性炭纤维的主要性能和它在环境领域中的应用研究。     

活性炭纤维复合材料的脱硫性能

本实验以粘胶基活性炭纤维和酚醛树脂复合,制备出了一种可用于烟气脱硫的活性炭纤维复合材料（ACFM）,考察了制备工艺条件对脱硫性能和比表面积的影响,测试其在填充床的压降。结果表明：粘结剂用量、炭化及活化条件对样品的脱硫性能和比表面积有较大的影响;与其他活性炭材料相比ACFM压降相对较低,只有活性炭纤维的1／20。     

炭基催化剂用于处理H2S的研究进展＊

介绍了国内外在常温下处理硫化氢等恶臭气体的炭基催化剂的研究进展情况,分析了炭基催化剂中活性炭、活性炭纤维、超级活性炭的特性及国内外应用现状,从工艺技术、成本、环保等几方面总结了此类常温脱硫催化剂的应用情况和优缺点,并对炭基脱硫催化剂未来的应用空间和发展方向进行了展望。     

硫化废气污泥活性炭净化处理技术研究

以污泥厂剩余活性污泥作为原料,采用KOH为活化剂制备污泥活性炭,探讨了活化温度及时间、热解温度、洗涤温度及方式在污泥活性炭制备过程中的最佳工艺条件。以品红吸附量及产率作为污泥活性炭的考察指标,采用单因素实验筛选出了制备污泥活性炭的最佳工艺条件,并对污泥活性炭脱硫剂的脱硫性能进行了实验研究。实验研究结果显示,烟气中O2、水蒸气含量的多少及脱硫温度的高低会影响污泥活性炭脱硫剂的脱硫性能。     

炭法烟气脱硫机理的研究现状

炭法烟气脱硫技术是一种污染治理与资源回收利用相结合的脱硫技术,本文在对活性炭吸附催化转化SO2过程、H2O和O2的存在对脱硫过程的影响,以及改性活性炭脱硫性能提高影响因素等方面分析基础上,论述了炭法脱硫机理研究现状,并提出了以后的发展方向。     

铜改性活性炭纤维吸附甲醛实验研究

室内甲醛气体是一种常见的室内污染物,对人体有害。近年来,吸附甲醛的研究成为国内外的热点。使用超声波协同负载,在可塑性高的活性炭纤维(ACF)材料上负载铜离子改性用于治理室内甲醛等污染。利用扫描电子显微镜(SEM),光电子能谱(EDS)对载铜ACF进行表征,发现含铜化合物附着在ACF表面。其中的含铜基团对甲醛的吸附起了重要作用。根据吸附材料吸附对比研究,所得的载铜ACF吸附效果优于其他吸附材料,甲醛去除率在80min内可达到0.063mg/g,比未改性活性炭高26%,比活性炭高57.5%,比生物质炭高75%。     

窗口温度下活性炭用于烟气脱硫的实验研究

研究了窗口温度下活性炭用于烟气脱硫的控制条件，对影响活性炭烟气脱硫的重要影响因素进行了分析，得出：烟气进口氧气含量为9％左右，温度在190℃左右脱硫率较佳；水蒸气含量增加，脱硫率增大；空塔速度增大，脱硫率降低；活性炭用于工业当中要考虑适当的水蒸气含量和空塔速度以节约成本。     

活性炭纤维对Cu2＋吸附性能的研究

研究了pH值、吸附接触时间、铜离子的初始浓度及活性炭纤维（ACF）的投加量对活性炭纤维吸附Cu2＋的影响,并选取了最佳的实验条件。用Langmuir方程和Freundlich方程拟合活性炭纤维对Cu2＋吸附等温线,结果表明：活性炭纤维吸附Cu2＋更符合Langmuir等温式,其相关系数为0．9995,以单分子层吸附为主。对活性炭纤维改性能明显提高对Cu2＋的吸附,其中效果最佳的吸附量从4．8mg／g增加到17．32mg／g,提高了3．6倍。     

活性炭烟气脱硫技术研究新进展

研制了新型活性炭脱硫剂－脱硫活性碳纤维。研究表明，脱硫活性碳纤维由于含碳量高、比表面积大、微孔丰富、孔径分布窄、有较多适于吸附ＳＯ２的表面官能团，因而吸附能力及吸附、脱附速度显著大于普通活性炭。在相同工艺条件下，脱硫活性碳纤维吸附容量为粒状疾性炭的４－５倍，空速粒达活性炭的１０倍。采用活性碳纤维脱硫可比普通活性碳脱硫剂用量成倍减少。另外，由于活性碳纤维阻力小，系统能耗可显著降低。活性碳烟气脱硫采用     

活性炭纤维在油田采出废水处理中的应用

针对油田采出废水的特点,以粘胶基活性炭纤维为原料,经二次炭化和二次活化方式处理制得ACF样品。以ACF为过滤材料,对延长某采油厂经过沉降、分离处理后的采油废水进行动态吸附实验,实验结果表明:经水蒸汽二次活化得到的ACF样品对选用的油田废水处理效果最佳,其悬浮物颗粒粒径中值0.496μm(<1.0μm)、悬浮物含量为0.77mg/L(<1.0mg/L)。     

The influence of different surface-modification treatments on biomass-based carbons and their effects on adsorption of carbon dioxide

Surface modification of biomass-based carbon with nitrogen-containing functional groups is performed by the different modification method, including the thermal and chemical methods. We also investigate the effect of the different reaction parameters on their pore structure using the Brunauer–Emmett–Teller surface area and adsorption performance based on methylene blue value. Fourier transforms infrared spectroscopy methods are performed to confirm the presence of N-containing groups. Based on above results, the comparison effect of different modification methods on physico-chemical propriety and adsorption properties of biomass-based carbon materials are carried out. In conclusion, all modification methods could enhance CO₂ adsorption capability. However, the carbon materials treated with ammonia using thermal method show the best performance.     

过滤吸附装置人字形布置公式浅谈

过滤吸附装置是有机废气过滤吸附箱的核心部件，其人（之）字形布置公式系根据工程实践总结出来的计算公式。本文介绍了活性炭纤维吸附装置布置公式的提出背景、推导过程和应用验证，以及采用本公式的优点。     

GOALS IN WASTEWATER TREATMENT1

Within a few years all domestic wastewater effluents in the United States will be subjected to a minimum of a properly operated primary and secondary treatment process. This implies a very high degree of removal of the more readily biologically degradable material as measured by the BOD test. This practice will to a large degree negate the value of the BOD test as a pollution parameter. Organic carbon appears to be a more suitable means for determining the strength of a wastewater or for controlling the operation of physical and chemical treatment processes. Studies were conducted to determine the effect of time of passage on the ratio of organic carbon to BOD, COD and carbohydrate. The ratio was found to vary with both time and the state of the sample. The carbon content was reduced to a lesser degree than the other parameters. Organic carbon content appears to correlate better with COD than with BOD. The efficiency of a chemical precipitation process can be determined on the basis of organic carbon removal.     

典型染料医药化工园区清洁生产与循环经济发展路径研究

本研究以典型染料医药精细化工园区HSEDA为对象,从四个方面分析其近17年来产学研政合作推行清洁生产与发展循环经济的技术路径与创新实践、所取得的减污降碳绩效,以及未来展望。研究发现,HSEDA绿色低碳循环发展有四个特征：(1)突出园区精细化物质流能量流管理,自下而上理清多产品、多元素、多层级物质能量代谢结构、路径和过程,定量揭示全生命周期环境影响,设计清洁生产和循环经济靶向措施;(2)染料行业自主开发了连续硝化、催化加氢、重氮化,高效分离、传热传质偶合等清洁技术,提效减排绩效显著;(3)医药行业开发了维生素、喹诺酮关键中间体短流程绿色合成技术,提高了原子经济性;(4)园区定量分析反应、工艺及物料全生命周期安全特性和风险,系统设计,提高本质安全。2006—2019年,HSEDA实现经济与资源、能源、环境脱钩发展。在“双碳”战略下,从系统角度提出园区“一核六驱”绿色低碳循环发展新模式。     

活性炭的吸附机理及其在水处理方面的应用

本文从活性炭表面的物理性质和化学性质,介绍了活性炭吸附的一般机理。综述了活性炭在城市给水、工业废水及城市污水深度处理中的研究进展;混凝—活性炭吸附工艺在净水工程中的应用;臭氧—生物活性炭技术去除水中有机污染物的工艺;MBR/PAC组合工艺及工业上使用石灰石与活性炭联合去除污染物的技术;从活性炭吸附性能指标的选择、有机物分子量的分布、活性炭的改性等方面,提出了活性炭在水处理应用上的问题和展望。     

Adsorption of phenol and its derivatives from water using synthetic resins and low-cost natural adsorbents: a review

In this article, the technical feasibility of the use of activated carbon, synthetic resins, and various low-cost natural adsorbents for the removal of phenol and its derivatives from contaminated water has been reviewed. Instead of using commercial activated carbon and synthetic resins, researchers have worked on inexpensive materials such as coal fly ash, sludge, biomass, zeolites, and other adsorbents, which have high adsorption capacity and are locally available. The comparison of their removal performance with that of activated carbon and synthetic resins is presented in this study. From our survey of about 100 papers, low-cost adsorbents have demonstrated outstanding removal capabilities for phenol and its derivatives compared to activated carbons. Adsorbents that stand out for high adsorption capacities are coal-reject, residual coal treated with H3PO4, dried activated sludge, red mud, and cetyltrimethylammonium bromide-modified montmorillonite. Of these synthetic resins, HiSiv 1000 and IRA-420 display high adsorption capacity of phenol and XAD-4 has good adsorption capability for 2-nitrophenol. These polymeric adsorbents are suitable for industrial effluents containing phenol and its derivatives as mentioned previously. It should be noted that the adsorption capacities of the adsorbents presented here vary significantly depending on the characteristics of the individual adsorbent, the extent of chemical modifications, and the concentrations of solutes.