Analytical determination of the suitability of different processes for the treatment of odorous waste gas

In order to determine the efficiency of different treatment systems for the reduction of odorous emissions, a gas chromatographic method followed by simultaneous mass spectrometry and olfactometry (GC-MS/O) was developed. Samples from a coffee bean roasting and a fat and oil processing plant were analyzed, respectively. The results were compared with the data obtained by olfactometric measurements. At a coffee bean roasting plant, cooling gases were analyzed prior to and after treatment in a full scale bioscrubber. The GC-MS/O analysis showed that the amounts of aldehydes and ketones decreased after treatment of cooling gases of coffee bean roasting in the bioscrubber, whereas the contents of the heterocyclic compounds, like pyridine and the pyrazines, and acetophenone and guaiacol remained almost unchanged. The amounts of dimethyl disulfide, 3-hydroxy-2-butanone, and the carboxylic acids increased after bioscrubber treatment. Furthermore, the performance of each stage of a combined experimental plant for the treatment of exhaust air of fat and oil processing was investigated. This treatment plant consisted of a bioscrubber, a biofilter, and an activated carbon adsorber. The important odor-active compounds of the exhaust air of fat and oil processing were the typical fat oxidation products (aldehydes, ketones) and with lower importance 2-pentylfuran, a few terpenes and aromates. Again, the key odor-active compounds, aldehydes and ketones, were degraded in the bioscrubber. Further degradation of aliphatic, unsaturated, methylated, and cyclic alkanes, as well as aromates, terpenes, and furans by the biofilter was observed. After the last treatment stage, the activated carbon filter, only small amounts of aliphatic, unsaturated, methylated, and cyclic alkanes and aromates remained in the waste gas. For both applications, the results of the developed GC-MS/O method correlated very well with olfactometric measurements.     

Survey of carbonization facilities for municipal solid waste treatment in Japan

The operations of carbonization facilities for municipal solid waste treatment in Japan were examined. Input waste, system processes, material flows, quality of char and its utilization, fuel and chemical consumption, control of facility emissions, and trouble areas in facility operation were investigated and analyzed. Although carbonization is a technically available thermochemical conversion method for municipal solid waste treatment, problems of energy efficiency and char utilization must be solved for carbonization to be competitive. Possible solutions include (1) optimizing the composition of input waste, treatment scale, organization of unit processes, operational methods, and quality and yield of char on the basis of analysis and feedback of long-term operating data of present operating facilities and (2) securing stable char demands by linking with local industries such as thermal electric power companies, iron manufacturing plants, and cement production plants.     

协同创新视角下资环专业研究生科技创新能力提升途径

资源循环科学与工程专业硕士毕业生存在规模小、科技创新能力不足、能力施展受限等问题,无法满足产业对高层次人才的需求。究其原因有:(1)新兴专业,其研究生导师队伍建设不健全,人才培养质量参差不齐;(2)交叉专业,其科技创新能力培养方向尚需融合凝练;(3)综合专业,其现有科研平台还不足以支撑学科发展,科技创新能力培养模式还没有完全形成。因此,本学科研究生培养单位应树立协同创新理念,坚持行业需求导向,充分挖掘办学特色和优势,凝练培养方向、完善以科技创新能力培养核心的研究生培养方案;加强师资队伍建设,建立健全科研平台;支持鼓励科技创新实践活动,做好学科前沿追踪;加强校校交流互动,提升硕士点认可度。     

Managing environmental problems during transitions: The department of energy as a case study

Many federal, state, and private agencies deal with long‐term environmental problems within a transition framework where political administrations, funds, regulators, regulatory requirements, environmental conditions, and tribal and stakeholder concerns change. In this article, we examine the types of transitions, as well as important stabilities, that agencies face, the interactions with stakeholders that are vulnerable to disruption or failure, and some of the problems that develop as a result of these conditions, using the U.S. Department of Energy (US DOE's) Office of Environmental Management (EM) as a case study. Transitions, or instabilities, include changes in administrations at the federal, state, and local level; public perceptions and concerns; political climate; available funds; environmental conditions (e.g., global climate change, global contaminant transport, local and regional contamination); international and national business conditions; and site conditions (physical, chemical, biological). Governmental agencies operate under several different kinds of uncertainties, including scientific, fiscal‐year economic, technological, and societal. Not all information can be known, and the outcomes from scientific issues or technologies cannot always be predicted. The authors believe that transitions from one set of conditions to another can be more effectively integrated with the long‐term stability of environmental laws and regulations, and with the stability of the treaty rights and concerns of tribal nations, as well as the shorter‐term stability of career personnel and established programs. A sense of stability for government agencies allowing maintenance of ongoing environmental management programs can also be achieved through processes and programs, such as establishing long‐term contracts (for remediation or restoration work), schedule and scope documents, future land‐use documents, National Environmental Research Parks (which obligate lands to study and conservation), and other programs that set the direction of work and activities for many years. Further, two other factors are essential for success within any agency facing transitions: (1) expectations should be both forward‐looking and realistic, and (2) there must be flexibility in both programs and processes. The authors conclude that several features are essential to addressing some of the problems created by transitions, including information, integration, iteration, interaction, and inclusion. © 2009 Wiley Periodicals, Inc.     

我国焦化行业面临的环境困境及绿色转型策略

综述了我国焦化行业的产能、产量、布局、装备水平及污染物排放特征,剖析了我国焦化行业目前存在的产能过剩、废气污染源超标排放、兰炭企业管理薄弱、独立焦化企业大量存在以及大气环境防护距离难以满足要求等环境困境,从构建煤焦钢产业链、做好排放标准与排污许可制度的衔接、加强对焦化企业的科学监管、实施科学合理的停限产方案、强化VOCs治理工作等方面提出了行业绿色转型发展的对策建议。     

解读《关于深入推进重点行业清洁生产审核工作的通知》

2020年10月16日,生态环境部和国家发改委联合发布了《关于深入推进重点行业清洁生产审核工作的通知》(环办科财〔2020〕27号)(《通知》),以进一步加强清洁生产审核在重点行业节能减排和升级改造中的支撑作用,促进形成绿色发展方式,推动经济高质量发展.本文在分析《通知》出台的背景和意义的基础上,对清洁生产审核工作的顶...     

An overview of metals recovery from thermal power plant solid wastes

Thermal power plants (TPPs) that burn fossil fuels emit several pollutants linked to the environmental problems of acid rain, urban ozone, and the possibility of global climate change. As coal is burned in a power plant, its noncombustible mineral content is partitioned into bottom ash, which remains in the furnace, and fly ash, which rises with flue gases. Two other by-products of coal combustion air-pollution control technologies are flue gas desulfurization (FGD) wastes and fluidized-bed combustion (FBC) wastes. This paper analyzed and summarized the generation, characteristics and application of TPP solid wastes and discussed the potential effects of such solid wastes on the environment. On this basis, a review of a number of methods for recovery of metals from TPP solid wastes was made. They usually contain a quantity of valuable metals and they are actually a secondary resource of metals. By applying mineral processing technologies and hydrometallurgical and biohydrometallurgical processes, it is possible to recover metals such as Al, Ga, Ge, Ca, Cd, Fe, Hg, Mg, Na, Ni, Pb, Ra, Th, V, Zn, etc., from TPP solid wastes. Recovery of metals from such wastes and its utilization are important not only for saving metal resources, but also for protecting the environment.     

A purview of waste management evolution: special emphasis on USA

The generation of waste in urban regions over time is seen to impact the balance of anthropogenic and natural resources. Various national and international initiatives to manage urban solid waste are in place and has thus have evolved at present to form an assortment of different subcomponents involving environmental, administrative, regulatory, scientific, market, technology, and socio-economic factors, which has increasing bearing on the US due to its volume and nature of discards. This paper draws together the various aspects of municipal solid waste (MSW) management as it evolved, particularly in the American society through reviewing works and findings. In many parts of the country, waste management at present, primarily involves landfilling, incineration with and without energy recovery, recycling and composting. Legislation, nature of wastes and market trends continue to redefine management operations and its responsibilities and impacts. Complexities are added to it by the nature of urban development as well. New studies and concepts like 3Rs, cradle-to-cradle, industrial ecology, and integrated waste management are adding new dimensions for solving waste problems towards achieving sustainable resource use. Local initiatives, both public and private are in the forefront of adopting alternate waste management procedures. The assistance from various government and private bodies, supporting shifts in waste management approaches, have immense value, as according to the new paradigms, nothing goes to waste.     

Vitrification for reclaiming spent alkaline batteries

The object of this study is to stabilize spent alkaline batteries and to recover useful metals. A blend of dolomite, limestone, and cullet was added to act as a reductant and a glass matrix former in vitrification. Specimens were vitrified using an electrical heating furnace at 1400 °C and the output products included slag, ingot, flue gas, and fly ash. The major constituents of the slag were Ca, Mn, and Si, and the results of the toxicity leaching characteristics met the standards in Taiwan. The ingot was a good material for use in production of stainless steel, due to being mainly composed of Fe and Mn. For the fly ash, the high level of Zn makes it economical to recover. The distribution of metals indicated that most of Co, Cr, Cu, Fe, Mn, and Ni moved to the ingot, while Al, Ca, Mg, and Si stayed in the slag; Hg vaporized as gas phase into the flue gas; and Cd, Pb, and Zn were predominately in the fly ash. Recovery efficiency for Fe and Zn was >90% and the results show that vitrification is a promising technology for reclaiming spent alkaline batteries.     

Aerosol Composition Change due to Dust Storm: Measurements between 1992 and 1999 at Gosan,Korea

Aerosol composition change between dust storm and non duststorm periods is studied using the TSP (Total SuspendedParticulate) data measured at Gosan, Korea between 1992 and1999. The concentrations of elements measured between 1993and 1996 and those of ions between 1992 and 1999 duringdust storms are compared with those during non-dust stormperiods in spring (March, April, and May). Among theanalyzed ions, the concentrations of crustal species(potassium, calcium, magnesium, and chloride) andanthropogenic species (nitrate and non-sea salt (nss)-sulfate) increased when dust storm occurs while those ofammonium and sodium did not increase. Among the analyzedelements, the concentrations of crustal species (Fe, Al,Ca, Ti, and Zn) increased when dust storm occurs whilethose of anthropogenic species (Mn, V, Ni, Cu, Cd, and Cr)did not increase. The only anthropogenic element of whichconcentration increased during dust storm periods was Pb.It was found that the concentrations of nitrate and nss-sulfatewere highest during spring. Also, the ratio of theyearly average concentrations of nitrate to nss-sulfateincreases, probably due to the emission trend change innortheast Asia, especially, in China.     

麦秸基木质陶瓷/凹凸棒石复合材料制备与性能表征

介绍了以麦秸秆、凹凸棒石为原料,以酚醛树脂、固化剂为辅料,按照不同的配比进行混合、干燥、热压,而后采用高温烧结工艺,制备新型复合碳材料。试验制备了各种不同原料配比以及不同烧结温度下的材料,并对材料的物理强度、密度、气孔率、强度、电阻率等性能进行了测试,对其性能表征、形成机理和形成规律进行分析,初步探讨了原料选择、原料配比、碳化温度等参数对制备工艺以及复合材料性能的影响,确定了当麦秸秆∶凹凸棒石=2∶1和3∶1,温度为700～800℃时,材料的各物理性能较为理想。实验证明麦秸秆为原材料制备凹凸棒石的可行性,为麦秸秆的资源化利用、凹凸棒石的应用以及木质陶瓷复合材料的研究开辟了新的研究方向。     

Recycling plastics from automotive shredder residues: a review

Automotive shredder residue (ASR) is an inevitable by-product of car recycling, i.e. removal of all liquids and hazardous or valuable components from the car and shredding of the hulk, followed by the recovery of steel, iron, and non-ferrous scrap. The European Union (EU) ELV Directive requires attaining higher recovery and recycling rates, resulting in a reduction of the amount of ASR going to landfill. The most plausible methods to achieve a considerable reduction of ASR are as follows: either recycling of separated materials and dismantled bulky parts, such as bumpers, dashboards, cushions, and front and rear windows, or else systematic sorting of the commingled and size-reduced materials, resulting from shredding. After a brief comparison of the actual situation in the EU, the USA, and Japan, the characteristics of actual ASR are reviewed, as well as some of the most prominent efforts made to separate and recycle specific fractions, such as polyolefins, ABS, or polyurethane. Attention is paid to some major players in the EU and to some of the pitfalls that besiege these ventures.     

建筑可持续发展视角下供应链协调与社会责任共担机理研究方案架构

基于建筑全生命周期这个主线,建筑可持续发展视角下供应链协调与社会责任共担机理研究,以绿色建筑供应链运行效率为导向,以既有建筑节能改造效率为切入点,以产业链过程中各主体行为规律为基础,采用“总-分-合”的基本研究思路模式,聚焦了“主导企业驱动下绿色建筑供应链协调机理与策略、既有建筑节能改造主体社会责任共担机理、建筑废弃物再生利用产业链主体社会责任共担机理”等三部分核心内容,初步形成建筑可持续发展视角下供应链协调与社会责任共担机理的理论体系。本成果采用“总-分-合”的思路模式,基于循环经济理念和主体行为策略视角,遵循研究的学理逻辑,以研究生学位论文为基础,开展“主导企业驱动下绿色建筑供应链协调机理与策略、既有建筑节能改造主体社会责任共担机理、建筑废弃物再生利用产业链主体社会责任共担机理”3个子课题研究,从系统整体概况实施全面研究规划着手,构架了总括、绿色建筑供应链协调机理、既有建筑节能改造主体社会责任共担、建筑废弃物再生利用社会责任共担、总结等五大模块及上中下三大篇共12章的系统体系。     

百菌清污染土壤生物修复研究进展

针对百菌清具有在土壤中药效稳定、不易分解、代谢周期长、长期大量施加导致土壤严重污染等特点和问题,简要介绍了百菌清的毒性作用机制。总结了降解土壤中百菌清的物理法、化学法和生物法的原理及优缺点。重点阐述了生物修复百菌清污染土壤的主要降解菌株及其效果、降解途径以及降解产物及其毒性,分析了土壤性质、微生物种类、温度、土壤含水率等因素对百菌清降解效果的影响。指出今后的研究重点应为降解中间产物的毒性分析及其进一步的降解与转化问题,而复合菌制剂或多酶复合体系可实现百菌清的彻底降解和无害化。     

国内城市生活垃圾焚烧飞灰研究现状及进展

随着我国经济快速发展及城市化水平提升,城市生活垃圾产量越来越大,焚烧逐渐成为城市生活垃圾处理的主要方式.但焚烧会产生大量的垃圾焚烧飞灰(以下简称飞灰),飞灰属于危险废物.论述了飞灰的来源、成分、特性及危害,介绍了飞灰的处理处置技术:水泥固化技术、化学药剂稳定化技术、熔融固化技术、水热稳定化技术和水泥窑协同处理技术,并分...     

生物吸附在染料废水处理中的应用

生物吸附是微生物细胞和其它物质发生的一系列非发酵关联的吸附过程,其主要作用包括物理和化学吸附、静电作用、离子交换、络合、螯合、微量沉淀等。与生物降解相比,生物吸附不会产生有毒的代谢产物,为染料废水的处理和回收提供了一条经济可行的途径。综述了微生物对染料吸附的作用机制及影响因素如pH、温度、染料初始浓度等,介绍了生物吸附的发展现状及前景。     

Managing contaminated sites and the role of domestic and international forums

Domestic and international cooperation in the field of contaminated‐site management has increased dramatically in the past decade. The expected benefits of this cooperation include the reduction of duplication in remediation efforts, the coordination of contaminated‐site research, improved synergy between various stakeholders, enhanced policy development, and better information dissemination and technology transfer. This article identifies and briefly discusses key domestic and international collaborations, partnerships, and networks relating to contaminated‐site management and remediation. Also provided is information on how the forums can be accessed. Common themes identified across the forums discussed in this article include (1) the development and demonstration of innovative technologies, (2) the use of risk assessment, (3) the use of toxicology, bioavailability, and ecotoxicity testing, and (4) the increasing need to find holistic approaches for managing contaminated sites, such as guaranteed remediation programs and transfer of environment liability, and the need for understanding implications of remediation financing mechanisms. © 2001 John Wiley & Sons, Inc.     

Monitoring and Analysis of Water,Salt and Nutrient Fluxes at the Mouth of a Lagoon

An intensive sampling program of physical and chemical parameters has been undertaken at Vassova lagoon, northeast Greece, in order to examine water circulation and estimate the instantaneous and residual fluxes of water, salt, nutrients and chlorophyll-a through the entrance canal of this lagoon. Field data of hydrographic and water quality parameters were collected under neap and spring tidal cycles, and under winter and summer conditions, to account for the fortnight and seasonal effects in the lagoon. The analysis showed that the Eulerian residual transport is positive in direction during both tidal cycles, thus pushing water, salt, nitrate-nitrogen, phosphate-phosphorus and chlorophyll-a inward Vassova lagoon. Tidal pumping was mostly positive during the neap tide and negative during the spring tidal cycle, thus pushing water, salt, phosphorus and chlorophyll-a outwards of Vassova lagoon.     

The current municipal solid waste management situation in Tibet

The Tibetan Plateau has an average altitude of more than 4,000 m. The total area of Tibetan Plateau is 2,400,000 km2, which occupies 25% of the area of China. Due to the high altitude, the environment has low atmospheric pressure, low oxygen content, and low temperature, and is also fragile. Investigations concerning MSW generation and characteristics, MSW management, collection and transportation, and treatment and disposal of MSW covered four representative cities, including the urban areas of Lhasa city, Shigatse, Nedong of Lhoka and Bayi of Nyingtri. The results show that MSW generation in the urban areas of Lhasa city and Tibet were 450 t/d and 3,597 t/d, respectively, in 2006. However, accelerated economic development and flourishing tourism caused by the opening of the Qinghai-Tibet Railway (QTR) have greatly increased solid waste generation to a new high. It is predicted that MSW generation in Tibet will reach 4,026 t/d in 2010 and 4,942 t/d in 2020. MSW management and disposal lag behind MSW generation due to a number of factors such as equipment shortage, insufficient maintenance, exhaustion of waste treatment capacity and low recycling efficiency. Still, MSW in most areas is dumped in the open with no controls. Because no appropriate collection and treatment systems for leachate and landfill gas exist, untreated leachate is discharged directly into the environment, causing serious secondary pollution. Some suggestions on improving the MSW management system are presented in this paper.