Sample intake position and loading rates from nonpoint source pollution

Paired water samples were simultaneously activated from two different vertical positions within the approach section of a flow-control structure to determine the effect of sample intake position on nonpoint runoff parameter concentrations and subsequent event loads. Suspended solids (SS), total phosphorus (TP) and organic plus exchangeable nitrogen [(Or+Ex)-N] were consistently higher throughout each runoff event when sampled from the floor of the approach section as opposed to those samples taken at midstage. Dissolved molybdate reactive phosphorus (DMRP) and ammonium (NH₄-N) concentrations did not appear to be significantly affected by the vertical difference in intake position. However, the nitrate plus nitrite nitrogen [(NO₃+NO₂)-N] concentrations were much higher when sampled from the midstage position.Although the concentration differences between the two methods were not appreciable, when evaluated in terms of event loads, discrepancies were evident for all parameters. Midstage sampling produced event loads for SS, TP, (Or + Ex)–N, DMRP, NH₄-N, and (NO₃+NO₂)-N that were 44,39,35,80,71, and 181%, respectively, of floor sampling loads. Differences in loads between the two methods are attributed to the midstage position, sampling less of the bed load. The correct position will depend on the objective; however, such differences should be recognized during the design phase of the monitoring program.This work was supported by the Soil Science Department, College of Agriculture and Life Sciences, University of Wisconsin-Madison, and by the U.S. Environmental Protection Agency, Region V., Chicago, Illinois (Grant No. G005139-01).     

Roofing as a source of nonpoint water pollution

Sixteen wooden structures with two roofs each were installed to study runoff quality for four commonly used roofing materials (wood shingle, composition shingle, painted aluminum, and galvanized iron) at Nacogdoches, Texas. Each roof, either facing NW or SE, was 1.22 m wide x 3.66 m long with a 25.8% roof slope. Thus, there were 32 alternatively arranged roofs, consisting of four roof types x two aspects x four replicates, in the study. Runoff from the roofs was collected through galvanized gutters, downspouts, and splitters. The roof runoff was compared to rainwater collected by a wet/dry acid rain collector for the concentrations of eight water quality variables, i.e. Cu(2+), Mn(2+), Pb(2+), Zn(2+), Mg(2+), Al(3+), EC and pH. Based on 31 storms collected between October 1997 and December 1998, the results showed: (1) concentrations of pH, Cu, and Zn in rainwater already exceed the EPA freshwater quality standards even without pollutant inputs from roofs, (2) Zn and Cu, the two most serious pollutants in roof runoff, exceeded the EPA national freshwater water quality standards in virtually 100% and more than 60% of the samples, respectively, (3) pH, EC, and Zn were the only three variables significantly affected by roofing materials, (4) differences in Zn concentrations were significant among all roof types and between all roof runoff and rainwater samples, (5) although there were no differences in Cu concentrations among all roof types and between roof runoff and rainwater, all means and medians of runoff and rainwater exceeded the national water quality standards, (6) water quality from wood shingles was the worst among the roof types studied, and (7) although SE is the most frequent and NW the least frequent direction for incoming storms, only EC, Mg, Mn, and Zn in wood shingle runoff from the SE were significantly higher than those from the NW; the two aspects affected no other elements in runoff from the other three roof types. Also, Zn concentrations from new wood-shingle roofs were significantly higher than those from aged roofs of a previous study. The study demonstrated that roofs could be a serious source of nonpoint water pollution. Since Zn is the most serious water pollutant and wood shingle is the worst of the four roof types, using less compounds and materials associated with Zn along with good care and maintenance of roofs are critical in reducing Zn pollution in roof runoff.     

Optimal nonpoint source pollution control strategies for a reservoir watershed in Taiwan

The purpose of this study is to develop a model for optimal nonpoint source pollution control for the Fei-Tsui Reservoir watershed in Northern Taiwan. Several structural best management practices (BMPs) are selected to treat stormwater runoff. The complete model consists of two interacting components: an optimization model based on discrete differential dynamic programming (DDDP) and a zero-dimensional reservoir water quality model. A predefined procedure is used to locate suitable sites for construction of various selected BMPs in the watershed. In the optimization model, the objective function is to find the best combination of BMP type and placement, which minimizes the total construction and operation, maintenance, and repair (OMR) costs of the BMPs. The constraints are the water quality standards for total phosphorus (TP) and total suspended solids (TSS) concentrations in the reservoir. A zero-dimensional reservoir water quality model of the Vollenweider type is embedded in the optimization framework to simulate pollutant concentrations in Fei-Tsui Reservoir. The resulting optimal cost and benefit of water quality improvement are depicted by the model-derived trade-off curves. The modeling framework developed in the present study could be used as an efficient tool for planning a watershed-wide implementation of BMPs for mitigating stormwater pollution impact on the receiving water bodies.     

Chemical transport from paired agricultural and restored prairie watersheds

A five-year record of streamflow and chemical sampling data was evaluated to assess the effects of large-scale prairie restoration on transport of NO3-N, Cl, and SO4 loads from paired 5,000-ha watersheds located in Jasper County, Iowa. Water quality conditions monitored during land use conversion from row crop agriculture to native prairie in the Walnut Creek watershed were compared with a highly agricultural control watershed (Squaw Creek). Combining hydrograph separation with a load estimation program, baseflow and stormflow loads of NO3-N, Cl, and SO4 were estimated at upstream and downstream sites on Walnut Creek and a downstream site on Squaw Creek. Chemical export in both watersheds was found to occur primarily with baseflow, with baseflow transport greatest during the late summer and fall. Lower Walnut Creek watershed, which contained the restored prairie areas, exported less NO3-N and Cl compared with upper Walnut Creek and Squaw Creek watersheds. Average flow-weighted concentrations of NO3-N exceeded 10 mg/L in upper Walnut Creek and Squaw Creek, but were estimated to be 6.6 mg/L in lower Walnut Creek. Study results demonstrate the utility of partitioning loads into baseflow and stormflow components to identify sources of pollutant loading to streams.     

Relating landscape characteristics to non-point source pollution in mine waste-located watersheds using geospatial techniques

Landscape characteristics of a watershed are important variables that influence surface water quality. Understanding the relationship between these variables and surface water quality is critical in predicting pollution potential and developing watershed management practices to eliminate or reduce pollution risk. To understand the impacts of landscape characteristics on water quality in mine waste-located watersheds, we conducted a case study in the Tri-State Mining District which is located in the conjunction of three states (Missouri, Kansas and Oklahoma). Severe heavy metal pollution exists in that area resulting from historical mining activities. We characterized land use/land cover over the last three decades by classifying historical multi-temporal Landsat imagery. Landscape metrics such as proportion, edge density and contagion were calculated based on the classified imagery. In-stream water quality data over three decades were collected, including lead, zinc, iron, cadmium, aluminum and conductivity which were used as key water quality indicators. Statistical analyses were performed to quantify the relationship between landscape metrics and surface water quality. Results showed that landscape characteristics in mine waste-located watersheds could account for as much as 77% of the variation of water quality indicators. A single landscape metric alone, such as proportion of mine waste area, could be used to predict surface water quality; but its predicting power is limited, usually accounting for less than 60% of the variance of water quality indicators.     

Integrating contributing areas and indexing phosphorus loss from agricultural watersheds

Most states in the USA have adopted P Indexing to guide P-based management of agricultural fields by identifying the relative risk of P loss at farm and watershed scales. To a large extent, this risk is based on hydrologic principles that frequently occurring storms can initiate surface runoff from fields. Once initiated, this hydrological pathway has a high potential to transport P to the stream. In regions where hydrologically active areas of watersheds vary in time and space, surface runoff generation by "saturation excess" has been linked to distance from stream, with larger events resulting in larger contributing distances. Thus, storm-return period and P loss from a 39.5-ha mixed-land-use watershed in Pennsylvania was evaluated to relate return-period thresholds and distances contributing P to streams. Of 248 storm flows between 1997 and 2006, 93% had a return period of 1 yr, contributing 47% of total P (TP) export, while the largest two storms (10-yr return period) accounted for 23% of TP export. Contributing distance thresholds for the watershed were determined (50-150 m) for a range of storm-return periods (1-10 yr) from hydrograph analysis. By modifying storm-return period thresholds in the P Index and thereby contributing distance, it is possible to account for greater risk of P loss during large storms. For instance, increasing return period threshold from 1 (current P indices) to 5 yr, which accounted for 67% of TP export, increased the P-management restricted area from 20 to 58% of the watershed. An increase in impacted area relative to a decreased risk of P loss creates a management-policy dilemma that cannot be ignored.     

Development of environmental thresholds for streams in agricultural watersheds

Global increases in consumption of chemical nutrients, application of pesticides, and water withdrawal to enhance agricultural yield have resulted in degraded water quality and reduced water availability. Efforts to safeguard or improve environmental conditions of agroecosystems have usually focused on managing on-farm activities to reduce materials loss and conserve habitat. Another management measure for improving environmental quality is adoption of environmental performance standards (also called outcome-based standards). This special collection of six papers presents the results of four years of research to devise scientifically credible approaches for setting environmental performance standards to protect water quantity and quality in Canadian agriculturally dominated watersheds. The research, conducted as part of Canada's National Agri-Environmental Standards Initiative, aimed to identify Ideal Performance Standards (the desired environmental state needed to maintain ecosystem health) and Achievable Performance Standards (the environmental conditions achievable using currently available and recommended best available processes and technologies). Overviews of the papers, gaps in knowledge, and future research directions are presented. As humans, livestock, and wildlife (both terrestrial and aquatic) experience greater pressures to share the same limited water resources, innovative research is needed that incorporates a landscape perspective, economics, farm practices, and ecology to advance the development and application of tools for protecting water resources in agricultural watersheds.     

Classification and spatial mapping of riparian habitat with applications toward management of streams impacted by nonpoint source pollution

Management of riparian habitats has been recognized for its importance in reducing instream effects of agricultural nonpoint source pollution. By serving as a buffer, well structured riparian habitats can reduce nonpoint source impacts by filtering surface runoff from field to stream. A system has been developed where key characteristics of riparian habitat, vegetation type, height, width, riparian and shoreline bank slope, and land use are classified as discrete categorical units. This classification system recognizes seven riparian vegetation types, which are determined by dominant plant type. Riparian and shoreline bank slope, in addition to riparian width and height, each consist of five categories. Classification by discrete units allows for ready digitizing of information for production of spatial maps using a geographic information system (GIS). The classification system was tested for field efficiency on Tom Beall Creek watershed, an agriculturally impacted third-order stream in the Clearwater River drainage, Nez Perce County, Idaho, USA. The classification system was simple to use during field applications and provided a good inventory of riparian habitat. After successful field tests, spatial maps were produced for each component using the Professional Map Analysis Package (pMAP), a GIS program. With pMAP, a map describing general riparian habitat condition was produced by combining the maps of components of riparian habitat, and the condition map was integrated with a map of soil erosion potential in order to determine areas along the stream that are susceptible to nonpoint source pollution inputs. Integration of spatial maps of riparian classification and watershed characteristics has great potential as a tool for aiding in making management decisions for mitigating off-site impacts of agricultural nonpoint source pollution.     

Regional scale variability in sediment and nutrient delivery from small agricultural watersheds

Although many studies have pointed out the various controlling factors of sediment and nutrient delivery on a plot or watershed scale, little is known on the spatial variability of sediment and nutrient delivery on a regional scale. This study was conducted to reveal regional variations in sediment-associated nutrient delivery in central Belgium. Sediment deposited in 13 small retention ponds was sampled and analyzed for total phosphorus (TP), K, Mg, and Ca content. The TP content of the sediment deposits varied from 510 to 2001 mg P per kg sediment. Nutrients are predominantly fixed on the very fine sediment fraction (<16 microm), which is the reason why the nutrient trap efficiency of the ponds is only a fraction of the sediment trap efficiency. Average nutrient trap efficiency of the studied ponds varies between 4 and 31%, whereas sediment trap efficiency varies between 10 and 72%. For watersheds ranging from 7 to 4873 ha, sediment yield ranged between 1.2 and 20.6 Mg ha(-1) yr(-1), whereas TP export varied from 1.8 to 39.7 kg ha(-1) yr(-1). The observed spatial variability in nutrient losses is primarily attributed to regional variations in erosion and sediment yield values and to a far lesser degree to the spatial variations in fertilizer application. Redistribution of manure in the framework of an agricultural policy may increase the rate of nutrient delivery by ways of erosion and sediment transport.     

Climatic and agricultural factors in nutrient exports from two watersheds in Ohio

Export of agricultural nutrients and sediment to lakes and oceans is of great environmental concern in many agricultural watersheds. Recent years have seen efforts to reduce loads through agricultural practices such as conservation tillage, efficient fertilization, and reservation of erodible areas. Monitoring the efficacy of such efforts is complicated by the fact they take place against a varying climatic and hydrologic background. In this study, statistical analysis was used to identify those climatic, hydrologic, and agricultural variables that best explained variations in nitrate, phosphorus, and total suspended solids over the period 1976-1995 in two large agricultural watersheds that feed Lake Erie, those of the Maumee and Sandusky Rivers. The dominant variable was stream discharge; after curvefits to remove its influence, the residual loads were tested via stepwise linear regression to reveal the most significant explanatory variables. Loads of nitrate, total suspended solids, and total phosphorus tended to decrease when previous months were wet, except in the summer, and to decrease when snow cover was extensive. It is speculated that stores of nitrate in the soil were lost during wet periods through increased crop uptake and/or leaching. Nitrogen fertilizer application in the Maumee watershed decreased following dry periods, but not enough to decrease stream loads. Soluble reactive phosphorus loads were negatively correlated to conservation tillage and reserves, and positively correlated to fertilizer and manure sources. Results for total phosphorus were similar to those for total suspended solids, on which most transported phosphorus is adsorbed.     

A review of sediment predictive techniques as viewed from the perspective of nonpoint pollution management

User-oriented criteria for the evaluation of physically based management models are presented. These criteria emphasize the utility rather than the elegance of the model. The standards are then applied to efforts at predicting non-point pollutant loadings. In particular a critical review of sediment pollution is used as the basis for the evaluation of sediment yield models as management tools. A wide range of sediment yield models are rated and recommendations for their use are made.     

Effectiveness of grassed waterways in reducing runoff and sediment delivery from agricultural watersheds

Grassed waterways (GWWs) drain surface runoff from fields without gullying along the drainageway. Secondary functions include reducing runoff volume and velocity and retaining sediments and harmful substances from adjacent fields. Grass cover (sward)-damaging sedimentation in the GWW is commonly reduced by frequent mowing, but in doing so the effectiveness of the waterway relative to the secondary functions is reduced. Our objectives were to (i) evaluate whether the maintenance of a GWW can be reduced if on-site erosion control is effective, (ii) measure the effectiveness of such a GWW, and (iii) analyze the underlying mechanisms. A long-term (1994-2000) landscape experiment was performed in four watersheds, where two had GWWs for which maintenance was largely neglected. An intensive soil conservation system was established on all fields. Runoff and sediment delivery were continuously measured in the two watersheds with GWWs and in their paired watersheds that were similar, but without GWWs. Runoff was reduced by 90 and 10% for the two sets of paired watersheds, respectively. The different efficiencies of the GWWs resulted from different layouts (doubled width and flat-bottomed vs. v-shaped drainageway). The GWWs reduced sediment delivery by 97 and 77%, respectively, but the sward was not damaged by sedimentation. Grain sizes > 50 microm were settled due to gravity in both GWWs. Smaller grain sizes were primarily settled due to infiltration, which increased with a more effective runoff reduction. In general, the results indicated a high potential of GWWs for reducing runoff volume and velocity, sediments, and agrochemicals coming from agricultural watersheds.     

Identification of critical areas on forest lands for control of nonpoint sources of pollution

Most nonpoint source pollution problems on forest lands can be controlled by careful planning and management of specific critical areas. Critical areas include sites with high mass and surface erosion hazards, overland flow areas, and the riparian zone. Some guides for identifying critical areas are presented along with examples of land-use constraints that might be applied.     

Investigation of an Escherichia coli environmental benchmark for waterborne pathogens in agricultural watersheds in Canada

Canada's National Agri-Environmental Standards Initiative sought to develop an environmental benchmark for low-level waterborne pathogen occurrence in agricultural watersheds. A field study collected 902 water samples from 27 sites in four intensive agricultural watersheds across Canada from 2005 to 2007. Four of the sites were selected as reference sites away from livestock and human fecal pollution sources in each watershed. Water samples were analyzed for Campylobacter spp., Salmonella spp., Escherichia coli O157:H7, Cryptosporidium spp., Giardia spp., and the water quality indicator E. coli. The annual mean number of pathogen species was higher at agricultural sites (1.54 ± 0.07 species per water sample) than at reference sites (0.75 ± 0.14 species per water sample). The annual mean concentration of E. coli was also higher at agricultural sites (491 ± 96 colony-forming units [cfu] 100 mL(-1)) than at reference sites (53 ± 18 cfu 100 mL(-1)). The feasibility of adopting existing E. coli water quality guideline values as an environmental benchmark was assessed, but waterborne pathogens were detected at agricultural sites in 80% of water samples with low E. coli concentrations (<100 cfu 100 mL(-1)). Instead, an approach was developed based on using the natural background occurrence of pathogens at reference sites in agricultural watersheds to derive provisional environmental benchmarks for pathogens at agricultural sites. The environmental benchmarks that were derived were found to represent E. coli values lower than geometric mean values typically found in recreational water quality guidelines. Additional research is needed to investigate environmental benchmarks for waterborne pathogens within the context of the "One World, One Health" perspective for protecting human, domestic animal, and wildlife health.     

Phosphorus export from an agricultural watershed: linking source and transport mechanisms

Many source and transport factors control P loss from agricultural landscapes; however, little information is available on how these factors are linked at a watershed scale. Thus, we investigated mechanisms controlling P release from soil and stream sediments in relation to storm and baseflow P concentrations at four flumes and in the channel of an agricultural watershed. Baseflow dissolved reactive phosphorus (DRP) concentrations were greater at the watershed outflow (Flume 1; 0.042 mg L(-1)) than uppermost flume (Flume 4; 0.028 mg L(-1)). Conversely, DRP concentrations were greater at Flume 4 (0.304 mg L(-1)) than Flume 1 (0.128 mg L(-1)) during stormflow. Similar trends in total phosphorus (TP) concentration were also observed. During stormflow, stream P concentrations are controlled by overland flow-generated erosion from areas of the watershed coincident with high soil P. In-channel decreases in P concentration during stormflow were attributed to sediment deposition, resorption of P, and dilution. The increase in baseflow P concentrations downstream was controlled by channel sediments. Phosphorus sorption maximum of Flume 4 sediment (532 mg kg(-1)) was greater than at the outlet Flume 1 (227 mg kg(-1)). Indeed, the decrease in P desorption between Flumes 1 and 4 sediment (0.046 to 0.025 mg L(-1)) was similar to the difference in baseflow DRP between Flumes 1 and 4 (0.042 to 0.028 mg L(-1)). This study shows that erosion, soil P concentration, and channel sediment P sorption properties influence streamflow DRP and TP. A better understanding of the spatial and temporal distribution of these processes and their connectivity over the landscape will aid targeting remedial practices.     

A proposed methodology for measuring incremental environmental benefits from using constructed wetlands to control agricultural non-point-source pollution

A binary response estimation procedure using contingent valuation data is proposed for estimating the incremental environmental benefits associated with the use of constructed wetlands to control agricultural waste-water runoff. The model uses two binary responses per individual while circumventing the non-independence problems associated with follow-up valuation questions. Case study results suggest that the methodology provides a potentially effective means for measuring the non-market benefits of constructed wetlands in addition to water-quality maintenance.1998 Academic Press     

Landowner motivations for watershed restoration: lessons from five watersheds

Collaborative watershed management initiatives have increased tremendously over the past decade. One of the critical questions for these initiatives is how to influence private land management practices to improve watershed health. This article researches landowner motivations and preferences for watershed restoration efforts in five watersheds in Western Oregon. Based on a survey of 446 landowners and 80 personal interviews, the research revealed that landowner perspectives vary by socio-economic, cultural, and land use characteristics. They are strongly motivated by a concern for future generations and interpersonal influence is particularly important. Finances, time, and unfamiliarity were all significant barriers to the adoption of conservation practices. The findings also revealed considerable variation among landowners as to their trusted sources of information and preferred outreach methods. Beyond the findings in Oregon, the research suggests that watershed initiatives need to understand landowner characteristics and motivating factors to better promote watershed restoration and target outreach efforts.     

Poultry litter ash as a potential phosphorus source for agricultural crops

Maryland will impose restrictions on poultry litter application to soils with excessive P by the year 2005. Alternative uses for poultry litter are being considered, including burning as a fuel to generate electricity. The resulting ash contains high levels of total P, but the availability for crop uptake has not been reported. Our objective was to compare the effectiveness of poultry litter ash (PLA) and potassium phosphate (KP) as a P source for wheat (Triticum aestivum L.) in acidic soils, without and with limestone application. Two acidic soils (pH 4.25 and 4.48) were studied, unlimed or limed to pH 6.5 before cropping. The PLA and KP were applied at 0, 39, and 78 kg P ha(-1), after which wheat was grown. Limestone significantly increased wheat yield, but the P sources without limestone did not. The two P sources were not significantly different as P fertilizer. At the 78 kg P ha(-1) rate, wheat shoot-P concentrations were 1.10 and 1.12 g kg(-1) for the PLA treatment compared with 0.90 and 0.89 g kg(-1) for KP in the nonlimed and limed soils, respectively. Trace element concentrations in wheat shoots from the PLA treatment were less than or equal to KP and the control. The low levels of water-soluble P and metals in the soils and the low metal concentrations in wheat suggest that PLA is an effective P fertilizer. Further studies are needed to determine the optimum application rate of PLA as a P fertilizer.     

Emerging technologies for removing nonpoint phosphorus from surface water and groundwater: introduction

Coastal and freshwater eutrophication continues to accelerate at sites around the world despite intense efforts to control agricultural P loss using traditional conservation and nutrient management strategies. To achieve required reductions in nonpoint P over the next decade, new tools will be needed to address P transfers from soils and applied P sources. Innovative remediation practices are being developed to remove nonpoint P sources from surface water and groundwater using P sorbing materials (PSMs) derived from natural, synthetic, and industrial sources. A wide array of technologies has been conceived, ranging from amendments that immobilize P in soils and manures to filters that remove P from agricultural drainage waters. This collection of papers summarizes theoretical modeling, laboratory, field, and economic assessments of P removal technologies. Modeling and laboratory studies demonstrate the importance of evaluating P removal technologies under controlled conditions before field deployment, and field studies highlight several challenges to P removal that may be unanticipated in the laboratory, including limited P retention by filters during storms, as well as clogging of filters due to sedimentation. Despite the potential of P removal technologies to improve water quality, gaps in our knowledge remain, and additional studies are needed to characterize the long-term performance of these technologies, as well as to more fully understand their costs and benefits in the context of whole-farm- and watershed-scale P management.     

Use of a geographic information system for storm runoff prediction from small urban watersheds

The use of computer-assisted map analysis techniques for prediction of storm runoff from a small urban watershed in the United States is investigated. An automated procedure for calculating input parameters for the US Soil Conservation Service (SCS) method of predicting storm runoff volume and peak timing is presented. Advanced techniques of spatial analysis are used to characterize spatial coincidence, surface configuration and effective hydrologic distance. A limited verification of the automated procedure indicates that the model reasonably characterizes water flow. A sensitivity analysis of basin disaggregation suggests that the SCS method yields increased volume and peak discharge predictions as the watershed is divided into smaller and smaller subunits. As a means to demonstrate the practical application of the automated procedure, a simulation of the effects on surface runoff for a potential residential development is presented.