Atmospheric deposition of polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans, and dioxin-like polychlorinated biphenyls in the Kanto Region, Japan

The atmospheric bulk (dry and wet) deposition of dioxins was investigated at four locations (Tokyo, Yokohama, Tsukuba, and Tanzawa) in the Kanto region (in Japan) over one year using a stainless-steel pot. Annual average polychlorinated dibenzo-p-dioxins/polychlorinated dibenzofurans (PCDD/PCDF) deposition fluxes were estimated to be from 450 to 1300 ng/m2/yr, and the annual average TEQ fluxes from 5.7 to 17 ng-TEQ/m2/yr at the four locations. The PCDD/PCDF deposition flux was higher in winter than in summer. The deposition flux could be related to ambient temperature, particularly for less chlorinated PCDDs/PCDFs, while the deposition flux is not necessarily related to the amount of precipitation. The PCDD/PCDF deposition flux increased as the particle deposition flux increased, for the winter samples. Based on the ratio of the PCDD/PCDF deposition fluxes to the particle deposition fluxes, the contribution of the reentrainment of soil particles to the TEQ of PCDD/PCDF deposition was considered to be negligible in this region. Based on the air concentrations monitored near our deposition sampling points by the municipalities, the ratio of the annual deposition flux to the annual average air concentration was roughly estimated to be 0.082 cm/s. The range of deposition flux in the Kanto region was estimated to be from 1.5 to 31 (median: 9.8) ng-TEQ/m2/yr based on the range of air concentration data measured by the municipalities. The total annual deposition flux in the entire Kanto region was estimated to range from 50 to 900 g-TEQ/yr (median 320 g-TEQ/yr). This estimated flux was of the same order as the sum of estimated emissions from municipal solid waste incinerators and industrial waste incinerators in the Kanto region. The contributions of dioxin-like PCBs in Yokohama, Tsukuba, and Tanzawa depositions were less than 10% of the total TEQ; however, in Tokyo it was almost equal to or more than 50%.     

Atmospheric deposition of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) in urban and suburban areas of Korea

Bulk atmospheric samples (wet and dry) were collected monthly throughout a year at urban and suburban areas of Korea to assess the deposition flux and seasonal variations of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). The PCDDs/DFs deposition fluxes ranged from 1.0 to 3.7 ng TEQ/m²/year in the urban area and from 0.5 to 4.6 ng TEQ/m²/year in the suburban area. The deposition fluxes of PCDDs/DFs in this study were comparable to or lower than those previously reported at different locations. The atmospheric deposition fluxes of particles and PCDDs/DFs in winter tended to be higher than those in summer. However, monthly variations between particle and PCDDs/DFs deposition fluxes were small, and the correlation coefficients between the deposition fluxes of air particles and each homologue group of PCDDs/DFs varied according to the degree of chlorination of the homologue group. The deposition velocity of PCDDs/DFs in the urban area was estimated at 0.04 cm/s, which is a lower value than those found in other studies. The two most likely factors affecting the monthly variation of deposition fluxes are the ambient temperature and the amount of precipitation. In particular, the ambient temperature had an influence on the lower chlorinated homologues of PCDDs/DFs while precipitation had an influence on the higher chlorinated PCDDs/DFs. The PCDDs/DFs profiles in atmospheric deposition bulk samples showed a similar pattern at the urban and suburban sites. The possibility of the loading of PCDDs/DFs by Asian dust events could be partly confirmed by investigation of homologue profiles.     

Modeling the atmospheric transport and deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans in North America

The atmospheric fate of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) was simulated for the year 2000 in North America using a SMOKE/CMAQ-based chemical transport model that was modified for this purpose. The 1999 USEPA emission inventories of PCDD/Fs and criteria pollutants were used. The 1995 Canadian emission inventory of criteria pollutants and the 1995 Canadian area source emissions for PCDD/Fs were used with the 2000 Canadian point source emissions. Modifications to CMAQ involved coupling it with dual organic matter (OM) absorption and black carbon (BC) adsorption models to calculate PCDD/F gas–particle partitioning. The model satisfactorily reproduced the particle bound fractions at all rural sites for which there were measured data and across the whole domain, the modeled vs. measured differences in particle bound fractions were less than 20% for nearly all congeners. The model predicted ambient air PCDD/F concentrations were also consistent with measurements. Simulated deposition fluxes were within 58% of direct measurements. PCDD/F atmospheric depositions to each of the Great Lakes were estimated for the year 2000. The results indicate that approximately 76% of the total deposition of PCDD/Fs to the Great Lakes (in W-TEQ, or toxic equivalent units as defined by the World Health Organization) is attributed to PCDD/Fs absorbed into OM in aerosol. For all of the lakes, more than 92% of all deposition is particle phase wet deposition and only 5–8% is particle phase dry deposition. Wet deposition from the gas phase is negligible. Of the 17 toxic PCDD/F congeners, the Cl_4–5DD/F compounds contribute approximately 70% to the total atmospheric deposition to the Great Lakes. The seasonal changes in the PCDD/F deposition flux track variations in ambient temperature.     

Process analysis of ozone formation under different weather conditions over the Kanto region of Japan using the MM5/CMAQ modelling system

We have assessed the contributions of individual physical and chemical atmospheric processes on ozone formation under different weather conditions during a typical summer month (August 2005) using the MM5/CMAQ modelling system. We found that the ozone episodes in the Kanto region are dominated by three major patterns, of which Patterns I and II are regular summertime pressure patterns with a 26% and 16% frequency of occurrence, respectively. A process analysis at two typical sites in the Kanto region – one located in the central region of Tokyo and the other located in the rural areas of Kanto – indicates that ozone formation is mainly controlled by advection, vertical diffusion, dry deposition, and chemical processes. The ground-level ozone concentrations are enhanced mainly by the vertical mixing of ozone-rich air from aloft, whereas the dry deposition and chemical processes mainly deplete ozone. By investigating the effects of each process under different weather conditions, we found that the significant decrease in ozone removal due to the chemical and advection processes under conditions of high stagnation is the most important cause of the enhanced levels of ozone in the central region of Tokyo. The results of this study can contribute to a better understanding of ozone formation in the Kanto region, and they may be valuable for local policy makers for further development planning.     

Congener-specific characterization of PCDDs/PCDFs in atmospheric deposition: comparison of profiles among deposition, source, and environmental sink

In order to examine the input of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/PCDFs) from various airborne sources to environmental sinks, the atmospheric deposition of congener-specific PCDDs/PCDFs was investigated. Homologue and congener profiles of atmospheric depositions were compared with those of sources and environmental sinks to identify the relationship among atmospheric depositions, sources, and environmental sinks. Moreover, factor analysis was used to detect similarities, differences, and relationships of the variations in deposition fluxes among congeners within the same and different homologues. The results showed that the congener profiles of the atmospheric depositions were primarily determined by those of combustion emissions. Several congeners in some specific samples showed higher proportions within each homologue compared with representative depositions. This result can be partly explained by the influence of impurities in herbicides, 1,3,5-trichloro-2-(4-nitrophenoxy) benzene (CNP) and pentachlorophenol (PCP). The congener profiles of combustion emissions, representative depositions, and urban soils were very similar although their homologue profiles varied. This implied that PCDDs/PCDFs in the urban soils originate from the deposition of combustion emissions and that all congeners within each homologue behave identically in air and soil. Although the congener profiles of the representative depositions were different from those of the sediments in Tokyo Bay and the soil of a paddy field, the combination of congener profiles of the representative depositions and of the impurities in herbicides. CNP and PCP, can explain the congener profiles of the sediments and the paddy field. This study showed that congener-specific data are useful for source identification.     

Examination of dioxin fluxes recorded in dated aquatic-sediment cores in the Kanto region of Japan using multivariate data analysis

Past dioxin (coplanar polychlorinated biphenyl (Co-PCB), 2,3,7,8-substituted polychlorinated dibenzo-p-dioxin (PCDD) and 2,3,7,8-substituted polychlorinated dibenzofuran (PCDF)) fluxes recorded in dated aquatic-sediment cores were analyzed using principal component analysis (PCA). The data set consisted of samples from four cores collected from the Kanto region of Japan. Time trends and spatial differences in the dioxin flux were examined, and the potential relationship to emission sources was investigated. Twenty-five compounds and 58 core slices, corresponding to the later half of the 20th century, were subjected to the analysis. The PCA of both log-transformed and maximum-value-standardized data successfully divided the dioxin compounds into a small number of groups, and three similar clusters of Co-PCBs, PCDDs and penta- to hepta-CDFs were identified. PCB formulations used in the past are judged to have been responsible for the major part of the Co-PCB flux recorded in the sediment cores. However, the relationship to emission sources needs further investigation. It is suggested that most 2,3,7,8-substituted PCDDs and PCDFs are different from Co-PCBs in their emission sources or movements in the environment. The subcore clusters obtained from the PCA of log-transformed data show that the cores from different sampling areas exhibited distinct dioxin fluxes and compositions. Common time trends among the cores were more effectively summarized by the PCA of maximum-value-standardized data focusing on relative time trends. PC scores show that recently the flux of each dioxin compound in the four cores has been generally declining after having reached a peak.     

Dry deposition of particles and canopy exchange: Comparison of wet,bulk and throughfall deposition at five forest sites in Italy

The contribution of dry deposition to the total atmospheric input of acidifying compounds and base cations is of overwhelming importance. Throughfall measurements provide an estimate of the total deposition to forest soils, including dry deposition, but some uncertainties, related to the canopy interaction processes, affect this approach. We compared the concentrations and the fluxes of the main ions determined in wet-only, bulk and throughfall samples collected at five forest sites in Italy. The contribution of coarse particles deposited onto the bulk samplers was of prime importance for base cations, representing on average from 16% to 46% of the bulk deposition. The extent of this dry deposition depended on some geographical features of the sites, such as the distance from the sea and the annual rainfall. The possibility of applying specific bulk/wet ratios to estimate the wet deposition proved to be limited by the temporal variability of these ratios, which must be considered together with the spatial variability. A direct comparison of the dry contribution deriving from the bulk–wet and the throughfall–wet demonstrated that an extensive natural surface (forest canopy) performs better than a small synthetic surface (funnel of the bulk sampler) in collecting dry deposition of SO₄²⁻, NO₃⁻ and Na⁺. The canopy exchange model was applied to both bulk and wet data to estimate the contribution of dry deposition to the total input of base cations, and the uncertainty associated to the model discussed. The exclusive use of bulk data led to a considerable underestimation of base cation dry deposition, which varies among the study sites.     

Polychlorinated dibenzo-p-dioxins and dibenzofurans in invertebrate animals from a rural beach in Japan

PCDDs and PCDFs were analyzed by high resolution GC MS in several invertebrate animals collected from a rural beach in Japan. PCDDs and PCDFs were detected in all samples. Total concentration of PCDDs and PCDFs ranged 8.8–120 pg g⁻¹ wet and 3.5–38 pg g⁻¹ wet, respectively. TEQs of invertebrate animals examined ranged from 0.048 pg g⁻¹ wet in sea slug to 0.91 pg g⁻¹ wet in mussel. Isomer profiles in all samples were similar to each other despite of variety of species. Their major sources are estimated to be herbicides such as CNP and PCP, and combustion by using a statistical analysis of isomer profiles.     

Polycyclic aromatic hydrocarbon (PAH) deposition to and exchange at the air-water interface of Luhu, an urban lake in Guangzhou, China

Urban lakes are vulnerable to the accumulation of semivolatile organic compounds, such as PAHs from wet and dry atmospheric deposition. Little was reported on the seasonal patterns of atmospheric deposition of PAHs under Asian monsoon climate. Bulk (dry + wet) particle deposition, air-water diffusion exchange, and vapour wet deposition of PAHs in a small urban lake in Guangzhou were estimated based on a year-round monitoring. The total PAH particle deposition fluxes observed were 0.44-3.46 μg m⁻² day⁻¹. The mean air-water diffusive exchange flux was 20.7 μg m⁻² day⁻¹. The vapour deposition fluxes of PAHs ranged 0.15-8.26 μg m⁻² day⁻¹. Remarkable seasonal variations of particulate PAH deposition, air-water exchange fluxes and vapour wet deposition were influenced by seasonal changes in meteorological parameters. The deposition fluxes were predominantly controlled by the precipitation intensity in wet season whereas by atmospheric concentration in dry season.     

Characteristics and impacts of trace elements in atmospheric deposition at a high-elevation site,southern China

To investigate the regional background trace element (TE) level in atmospheric deposition (dry and wet), TEs (Fe, Al, V, Cr, Mn, Ni, Cu, Zn, As, Se, Mo, Cd, Ba, and Pb) in 52 rainwater samples and 73 total suspended particles (TSP) samples collected in Mt. Lushan, Southern China, were analyzed using inductively coupled plasma-mass spectrometry (ICP-MS). The results showed that TEs in wet and dry deposition of the target area were significantly elevated compared within and outside China and the volume weight mean pH of rainwater was 4.43. The relative contributions of wet and dry depositions of TEs vary significantly among elements. The wet deposition fluxes of V, As, Cr, Se, Zn, and Cd exceeded considerably their dry deposition fluxes while dry deposition dominated the removal of pollution elements such as Mo, Cu, Ni, Mn, and Al. The summed dry deposition flux was four times higher than the summed wet deposition flux. Prediction results based on a simple accumulation model found that the content of seven toxic elements (Cr, Ni, Cu, Zn, As, Cd, and Pb) in soils could increase rapidly due to the impact of annual atmospheric deposition, and the increasing amounts of them reached 0.063, 0.012, 0.026, 0.459, 0.076, 0.004, and 0.145 mg kg^?1, respectively. In addition, the annual increasing rates ranged from 0.05% (Cr and Ni) to 2.08% (Cd). It was also predicted that atmospheric deposition induced the accumulation of Cr and Cd in surface soils. Cd was the critical element with the greatest potential ecological risk among all the elements in atmospheric deposition.     

Atmospheric deposition of polycyclic aromatic hydrocarbons to Izmit Bay, Turkey

Wet deposition and dry deposition samples were collected in an urban/industrialized area of Izmit Bay, North-eastern Marmara Sea, Turkey, from September 2002 to July 2003. The samples were analyzed for sixteen polycyclic aromatic hydrocarbon (PAH) compounds by using HPLC-UV technique. Wet and dry deposition concentrations and fluxes of PAHs were determined. The results showed that PAH concentrations were high because of industrial processes, heavy traffic and residential areas next to the sampling site. Total dry deposition flux of the fifteen 3-6 ring PAHs was 8.30 microg m(-2)day(-1), with a range of 0.034-1.77 microg m(-2)day(-1). The total wet deposition flux of the fifteen 3-6 ring PAHs was 1716 microg m(-2) 11 month(-1), with a range of 10-440 microg m(-2) 11 month(-1). Significant seasonal differences were observed in both types of deposition samples. The winter fluxes of total PAHs were 1.5 and 2.5 times greater than those of the warm period for wet and dry deposition samples, respectively. Factor analysis of dry deposition samples and back trajectory analysis of wet deposition samples were also used to characterize and identify the PAH emission sources in this study.     

PCDDs/DFs emissions from crematories in Japan

Concentrations of PCDDs and PCDFs in emission gases from 10 crematories were measured. The relationship between PCDDs/DFs and several factors such as structure, equipment and operational state of the crematory is discussed. Furthermore, emission of PCDDs/DFs from all crematories in Japan is estimated. The following results are obtained: (1) total concentration of PCDDs/DFs was 2.2-290 ng/N m3, whose TEQ concentration was 0.0099-6.5 ng TEQ/N m3; (2) total concentration of PCDFs was higher than that of PCDDs; (3) T4CDFs was the highest in the homologue pattern and 2,3,7,8-T4CDF was the highest in the isomer pattern; (4) emission of PCDDs/DFs was the largest in the first 20 min of cremation; (5) concentration of PCDDs/DFs was related to the existence of a secondary combustion chamber and a dust collector, and the ratio of the numbers of main and secondary combustion chambers; (6) total emission of PCDDs/DFs from crematories in Japan was estimated to be 8.9 g TEQ/yr.     

Real-time-monitored decrease of trichlorophenol as a dioxin surrogate in flue gas using iron oxide catalyst

The decrease of trichlorophenol by injecting oxidation catalyst into a municipal solid waste incinerator was monitored in real time. Direct sampling atmospheric pressure chemical ionization (APCI)/ion trap mass spectrometry (ITMS) was used for the real-time monitoring. The oxidation catalyst was iron oxide type, which exponentially reduced trichlorophenol emission. CO emission, however, did not show any correlation with the catalyst injection rate. Simultaneous analysis of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/PCDFs) suggested that real-time monitoring of trichlorophenol as a surrogate of PCDDs/PCDFs, has a potential to timely control the optimum injection rate of PCDD/PCDF suppression catalyst continuously and economically.     

Comparison of annual dry and wet deposition fluxes of selected pesticides in Strasbourg, France

This work summarizes the results of a study of atmospheric wet and dry deposition fluxes of Deisopropyl-atrazine (DEA), Desethyl-atrazine (DET), Atrazine, Terbuthylazine, Alachlor, Metolachlor, Diflufenican, Fenoxaprop-p-ethyl, Iprodione, Isoproturon and Cymoxanil pesticides conducted in Strasbourg, France, from August 2000 through August 2001. The primary objective of this work was to calculate the total atmospheric pesticide deposition fluxes induced by atmospheric particles. To do this, a modified one-dimensional cloud water deposition model was used. All precipitation and deposition samples were collected at an urban forested park environment setting away from any direct point pesticide sources. The obtained deposition fluxes induced by atmospheric particles over a forested area showed that the dry deposition flux strongly contributes to the total deposition flux. The dry particle deposition fluxes are shown to contribute from 4% (DET) to 60% (cymoxanil) to the total deposition flux (wet + dry).     

PCDDs, PCDFs emission control by dry scrubbing system

Presently, in Japan there are no limitations on the emission of PCDDs or PCDFs, but in order to study the feasibility of dry type air pollution control, a pilot plant was constructed in 1988 and the removal efficiencies for PCDDs, acid gas and heavy metals were measured.At the same time PCDDs concentration was compared with that of a previously installed electrostatic precipitator (ESP) plus wet scrubber line.In this paper, the following two items are reported.

1. (1) The difference in the amounts of PCDDs and PCDFs produced due to differences in gas temperature and retention time in ESP and fabric filter (FF).

2. (2) Removal efficiencies of PCDDs and PCDFs of fabric filter.

PCDDs concentration, generally 100–200 ng/Nm³ at the boiler outlet (ESP inlet and/or Quench Reactor (QR) inlet), increased several times at the ESP outlet, but it showed almost no increase at the QR outlet due to a sudden temperature drop. The temperature was 280–310°C, and the gas retention time was 12 sec. during passage through ESP so that it is thought that PCDD was formed under these conditions.On the other hand, a removal efficiency of approx. 90% was obtained with the fabric filter, and the PCDD at the bag outlet was at a sufficiently low level.     

PCDDs/PCDFs, dl-PCBs and HCB in the flue gas from coal fired CFB boilers

The aim of the project was to measure the actual emissions of polychlorinated dibenzodioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), dioxin-like polychlorinated biphenyls (dl-PCBs) and hexachlorobenzene (HCB) from four selected power plants in Poland in order to update the national inventory of PCDDs/PCDFs emission. Relatively low PCDDs/PCDFs as well as dl-PCBs concentrations in flue gas obtained in measurements in this study for four different circulated fluidized bed (CFB) boilers indicate practical absence of any hazards caused by PCDDs/PCDFs emission from these units. The results of PCDDs/PCDFs determination obtained in this study indicate that hard coal combustion in large CFB in the four central heating plants (CHP) is not a significant source of PCDDs/PCDFs emission to the environment even if operated by co-firing of waste coal. PCDDs/PCDFs concentration in flue gases as well as emission factors were recorded in the range of 0.012-0.060ngI-TEQ/m(n)(3) and 7.51-46.4mugI-TEQ/TJ, respectively. Dl-PCBs concentration was practically below the LOQ=0.006ng WHO-PCB TEQ/m(n)(3) in all experiments. HCB concentration as well as emission factors were recorded in the range of 11.5-42.0ng/m(n)(3) and 6.19-26.7mg/TJ, respectively, where the highest value was obtained for co-firing of waste coal, however. Obtained in this work emission factors will be used for national emission inventory purposes instead of the factors proposed by Toolkit or taken from previous measurements. However, consideration should be given to the fact that the measurements in most cases are related to single installations. Therefore, the need for further development of national factors for the power generation industry in Poland is desired.     

Atmospheric bulk deposition of dioxin and furans to Danish background areas

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were measured in bulk deposition at three Danish rural forest sites with a mutual maximum distance of 450 km. At one of the forest sites concentrations in the ambient atmosphere were sampled from a 12 m high tower. Sampling was carried out within a period of 3 years with sampling intervals of 1–2 months. Mean bulk deposition fluxes were 1 ng m⁻² yr⁻¹ I-TEQ and deviated less than 30% between the sites. Yearly average PCDD/F concentrations in the atmosphere were 24 fg m⁻³ I-TEQ with maximum values in the winter period. During winter months atmospheric concentrations of PCDD/F and oxidized sulphur compounds showed a positive correlation, furthermore seasonal bulk deposition showed correlation between PCDD/F and sulphate.     

Photodegradation of polychlorinated dibenzo-p-dioxins and dibenzofurans in aqueous solutions and in organic solvents

Aqueous solutions of selected polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were prepared using a generator column and exposed to UV (300 nm) light in the laboratory and to sunlight in an outdoor environment. In the laboratory, additional exposures were also carried out using 60% acetonitrile/water solutions. At 300 nm di- and tetra PCDDs had higher first-order photodegradation rate constants in 60% acetonitrile/water than in pure water. The solvent effect was reversed for PCDFs. These results may be a reflection of the higher polarity of PCDFs compared to PCDDs. In both the indoor and outdoor exposures photodegradation rates decreased with increasing concentrations of chlorination. However, OCDF exposed to 300 nm light in 60% acetonitrile/water and to sunlight in pure water photodegraded more rapidly than tetra CDF. Photolysis rates in sunlight were considerably slower (t(1/2) of 6.4-23 h) than photolysis rates at 300 nm in the laboratory (t(1/2) of 4.3-680 min), reflecting the lower intensity of sunlight in the 300 nm region of the UV/Vis spectrum. The extent of dechlorination of the PCDDs/PCDFs was less than 20% and reductive dechlorination does not appear to be a major process in the photodegradation of PCDDs/PCDFs in aqueous solutions.     

Atmospheric deposition of phthalate esters in a subtropical city

In Chinese cities, air pollution has become a serious and aggravating environmental problem undermining the sustainability of urban ecosystems and the quality of urban life. Bulk atmospheric deposition samples were collected two-weekly, from February 2007 to January 2008, at three representative areas, one suburban and two urbanized, in the subtropical city, Guangzhou, China, to assess the deposition fluxes and seasonal variations of phthalate esters (PAEs). Sixteen PAE congeners in bulk deposition samples were measured and the depositional fluxes of ∑₁₆PAEs ranged from 3.41 to 190 μg m^?2 day^?1, and were highly affected by local anthropogenic activities. The significant relationship between PAEs and particulate depositional fluxes (correlation coefficient R² = 0.72, P < 0.001) showed PAEs are associated primarily with particles. Temporal flux variations of PAEs were influenced by seasonal changes in meteorological parameters, and the deposition fluxes of PAEs were obviously higher in wet season than in dry season. Diisobutyl phthalate (DiBP), Di-n-butyl phthalate (DnBP), and Di(2-ethylhexyl) phthalate (DEHP) dominated the PAE pattern in bulk depositions, which is consistent with a high consumption of the plasticizer market in China. PAE profiles in bulk deposition showed similarities exhibited in both time and space, and a weak increase of high molecular weight PAE (HMW PAE) contribution in the wet season compared to those in the dry season. Average atmospheric deposition fluxes of PAEs in the present study were significantly higher than those from other studies, reflecting strong anthropogenic inputs as a consequence of rapid industrial and urban development in the region.     

Local to regional emission sources affecting mercury fluxes to New York lakes

Lake-sediment records across the Northern Hemisphere show increases in atmospheric deposition of anthropogenic mercury (Hg) over the last 150 years. Most of the previous studies have examined remote lakes affected by the global atmospheric Hg reservoir. In this study, we present Hg flux records from lakes in an urban/suburban setting of central New York affected also by local and regional emissions. Sediment cores were collected from the Otisco and Skaneateles lakes from the Finger Lakes region, Cross Lake, a hypereutrophic lake on the Seneca River, and Glacial Lake, a small seepage lake with a watershed that corresponds with the lake area. Sediment accumulation rates and dates were established by ²¹⁰Pb. The pre-anthropogenic regional atmospheric Hg flux was estimated to be 3.0 μg m⁻² yr⁻¹ from Glacial Lake, which receives exclusively direct atmospheric deposition. Mercury fluxes peaked during 1971–2001, and were 3 to more than 30 times greater than pre-industrial deposition. Land use change and urbanization in the Otisco and Cross watersheds during the last century likely enhanced sediment loads and Hg fluxes to the lakes. Skaneateles and Glacial lakes have low sediment accumulation rates, and thus are excellent indicators for atmospheric Hg deposition. In these lakes, we found strong correlations with emission records for the Great Lakes region that markedly increased in the early 1900s, and peaked during WWII and in the early 1970s. Declines in modern Hg fluxes are generally evident in the core records. However, the decrease in sediment Hg flux at Glacial Lake was interrupted and has increased since the early 1990s probably due to the operation of new local emission sources. Assuming the global Hg reservoir tripled since the pre-industrial period, the contribution of local and regional emission sources to central New York lakes was estimated to about 80% of the total atmospheric Hg deposition.