Comparability between PM2.5 and particle light scattering measurements

Particle light scattering and PM_2.5 (particles with aerodynamic diameters less than 2.5 m) concentration data from air quality studies conducted over the past ten years wereexamined. Fine particle scattering efficiencies were determinedfrom statistical relationships among measured light scattering and fine and coarse mass concentrations. The resulting fine particle scattering efficiencies ranged from 1.7 m² g^-1at Meadview in the Grand Canyon to over 5 m² g^-1 in Mexico City. Most of the derived fine scattering efficiencieswere centered around 2 m² g^-1, which is considerablylower than most values reported from previous studies.     

Workplace aerosol mass concentration measurement using optical particle counters

Direct-reading aerosol measurement usually uses the optical properties of airborne particles to detect and measure particle concentration. In the case of occupational hygiene, mass concentration measurement is often required. Two aerosol monitoring methods are based on the principle of light scattering: optical particle counting (OPC) and photometry. The former analyses the light scattered by a single particle, the latter by a cloud of particles. Both methods need calibration to transform the quantity of scattered light detected into particle concentration. Photometers are simpler to use and can be directly calibrated to measure mass concentration. However, their response varies not only with aerosol concentration but also with particle size distribution, which frequently contributes to biased measurement. Optical particle counters directly measure the particle number concentration and particle size that allows assessment of the particle mass provided the particles are spherical and of known density. An integrating algorithm is used to calculate the mass concentration of any conventional health-related aerosol fraction. The concentrations calculated thus have been compared with simultaneous measurements by conventional gravimetric sampling to check the possibility of field OPC calibration with real workplace aerosols with a view to further monitoring particle mass concentration. Aerosol concentrations were measured in the food industry using the OPC GRIMM? 1.108 and the CIP 10-Inhalable and CIP 10-Respirable (ARELCO?) aerosol samplers while meat sausages were being brushed and coated with calcium carbonate. Previously, the original OPC inlet had been adapted to sample inhalable aerosol. A mixed aerosol of calcium carbonate and fungi spores was present in the workplace. The OPC particle-size distribution and an estimated average particle density of both aerosol components were used to calculate the mass concentration. The inhalable and respirable aerosol fractions calculated from the OPC data are closely correlated with the results of the particle size-selective sampling using the CIP 10. Furthermore, the OPC data allow calculation of the thoracic fraction of workplace aerosol (not measured by sampling), which is interesting in the presence of allergenic particles like fungi spores. The results also show that the modified COP inlet adequately samples inhalable aerosol in the range of workplace particle-size distribution.     

南京北郊气溶胶散射特性观测研究

南京北郊是重工业区,空气污染严重。该文利用浊度仪对大气气溶胶散射系数进行了四季观测,研究了该区气溶胶散射系数、后向散射比、质量散射系数及散射系数与能见度的关系,结果表明,观测期间散射系数波动较大,平均值为344.84 Mm^-1,标准差为215.99 Mm^-1,散射系数季节差异明显,主要受气象条件和外界污染排放的影响;后向散射比平均值为0.139,春季变化剧烈,夏、秋、冬季在波动中缓慢上升,大气中细粒子污染严重且含量有增加的趋势;散射系数与PM_2.5质量浓度相关系数达到0.91,质量散射系数平均值为1.87m²/g;散射系数与能见度之间存在-0.66的相关性,两者呈负幂函数关系。     

显微镜计数法测定浮游植物的研究进展及修订建议

介绍了国内外淡水浮游植物密度的测定——显微镜计数法的规范和标准。提出了国外有关标准中关于浮游植物在计数框中的分布要求、计数量与测定精密度的关联、检出限的计算方法等是值得借鉴的内容。通过实验验证了浮游植物在计数框中越符合随机分布,测定的精密度越好;随计数量的增加,观察到的浮游植物种类越多且测定精密度越好。借鉴英国标准BS/EN 15204：2006中关于检出限的定义和计算方法,得出了适用于中国规范中4种常用计数方式的检出限计算方法,并得出4种计数方式的检出限分别为对角线计数4.6×10⁵个/L、行格计数1.5×10⁵个/L、全片计数4.6×10⁴个/L、随机视野计数6.8×10⁵个/L。最后提出了应在中国相关规范中补充浮游植物在计数框中的分布要求、最少计数量与精密度的关联和确定检出限的方法等建议。     

室内空气中颗粒状污染物的PTV测量

针对室内空气中颗粒状污染物流动特性的测量搭建了PTV测量系统,该系统由白光照明、CCD摄像头采集图像及四轨迹像点匹配算法软件构成.测量结果表明,该PTV系统具有测量室内空气中可吸入颗粒扩散与流动的速度分布、浓度分布等特性.     

Morphological characterization of suspended particles under wind-induced disturbance in Taihu Lake, China

Sediments are disturbed by wind frequently, especially in the shallow lakes. The characteristics of resuspended sediment particles in Taihu Lake were studied under different wind velocities. It showed that sediment particles suspended obviously and particle number in overlying water increased directly under high wind-induced disturbance. Suspended solid (SS) concentration was less than 50 mg/l when the wind velocity was below 3.0 m/s, however, it increased to more than 300 mg/l when the wind velocity was 10.0 m/s. Two methods were used to measure the fractal characteristics of particles. One was light scattering and the other was image analysis. The three-dimensional fractal dimensions of suspended particles, measured by light scattering, were between 2.26 and 2.44; correspondingly, the two-dimensional fractal dimensions, calculated by image analysis, were between 1.44 and 1.77. Moreover, the three-dimensional fractal dimensions were directly proportional to two-dimensional fractal dimensions. The characteristic length of particles was calculated by image analysis. The minimum characteristic length was close to 8.5 μm when the wind velocity was 1.5 m/s at 50 cm beneath lake surface, while, the maximum characteristic length was approximate to 24 μm when the wind velocity was 10 m/s at the depth of 150 cm.     

珠三角秋冬季节长时间灰霾污染特性与成因

利用珠三角大气超级站2012年10月与2013年1月能见度、不同粒径颗粒物与BC质量浓度、气溶胶光散射系数、O3、相对湿度等在线监测数据,分析秋冬季节2次持续时间超过10 d的长时间灰霾过程污染特性与成因。结果表明,冬季灰霾过程中气溶胶吸光系数和光散射系数对大气总消光系数的贡献分别为13%和67%;PM2.5、PM1占PM10质量浓度分别为66%和39%;较高的PM2.5与BC日均浓度相关系数(R2=0.88)体现了一次排放对颗粒物质量浓度及能见度的显著影响。秋季灰霾过程中气溶胶吸光系数和光散射系数对大气总消光系数的贡献分别为11%和69%,由BC导致的吸光效应较冬季下降了约20%;PM2.5和PM1占PM10质量浓度比例分别为68%和45%,均高于冬季;O3浓度日最大小时值的平均值接近冬季的2倍;二次来源对PM2.5浓度升高和能见度下降起主导作用。来自不同方向的2种气团在珠三角僵持,大气扩散条件差是导致这2次灰霾过程的重要外在条件,应成为灰霾预报预警的重点关注对象。     

固定污染源颗粒物在线监测现状——以济南市为例

于2019年对济南市固定污染源颗粒物在线监测设备的品牌、方法原理和手工监测比对情况进行了分析。结果表明,4种激光前向散射法颗粒物在线设备比对结果符合性较好,带加热功能的采样头可以有效降低水滴的干扰;激光后向散射法颗粒物在线设备比对结果符合性较差,零点漂移达到3. 3%,2/3的手工比对数据绝对误差±5 mg/m3。指出,激光后向散射法设备不适用于超低排放企业,激光前向散射法设备因适用高湿度低量程环境,测量精度高,在济南市的适用性更好。     

长三角典型城市公交车实际道路细颗粒物排放测试

为研究长三角典型城市公交车细颗粒物排放特征,采用便携式排放测试系统（PEMS）,对上海、杭州和苏州三大城市的8辆典型城市公交车开展实际道路细颗粒物排放实验。研究结果表明：长三角典型城市车辆的实际道路平均车速为22.7 km/h,怠速比例为20.4%,加减速比例为54.5%;在稳态行驶工况下,随车速增大,公交车颗粒物质量及数量排放呈逐渐增大趋势;在20 km/h车速范围内,上海国III、国IV和苏州国III公交车颗粒数浓度呈双峰粒径分布,其他公交车均为单峰分布;随比功率的增大,公交车颗粒质量呈逐渐增大的趋势,国IV公交车颗粒数量呈先下降再增大趋势,国III公交车颗粒数量呈上升趋势;公交车颗粒质量综合排放因子为0.8~189 mg/km,颗粒数量综合排放因子为6.2×10¹²~9.6×10¹⁴#/km。     

Evaluation of the Fertilization Capability of Paracentrotus Lividus Sea Urchin Storaged Gametes by the Exposure to Different Aqueous Matrices

Several experiments were performed to evaluate the fertilization capability of Paracentrotus lividus sea urchin gametes, which are usually used in fertilization tests, but which, until now, were employed only for few hours after spawning.The aim of this work is to evaluate the possibility of performing the bioassay for longer periods, employing ‘conserved' gametes. As far as the method, the sperm was stored ‘dry' at 4 ^∘C; eggs were conserved in an antibiotic solution at 4 ^∘C, and they were exposed both to copper solutions as reference toxicant and to aqueous matrices.The use of conserved gametes in the fertilization bioassay lead to EC50 values which were acceptable for about 3 days. Moreover, these experiments permitted to identify the limiting factor: the male gamete.     

Statistical evaluation of photon count rate data for nanoscale particle measurement in wastewaters

The dynamic light scattering (DLS) technique can detect the concentration and size distribution of nanoscale particles in aqueous solutions by analyzing photon interactions. This study evaluated the applicability of using photon count rate data from DLS analyses for measuring levels of biogenic and manufactured nanoscale particles in wastewater. Statistical evaluations were performed using secondary wastewater effluent and a Malvern Zetasizer. Dynamic light scattering analyses were performed equally by two analysts over a period of two days using five dilutions and twelve replicates for each dilution. Linearity evaluation using the sixty sample analysis yielded a regression coefficient R(2) = 0.959. The accuracy analysis for various dilutions indicated a recovery of 100 ± 6%. Precision analyses indicated low variance coefficients for the impact of analysts, days, and within sample error. The variation by analysts was apparent only in the most diluted sample (intermediate precision ~12%), where the photon count rate was close to the instrument detection limit. The variation for different days was apparent in the two most concentrated samples, which indicated that wastewater samples must be analyzed for nanoscale particle measurement within the same day of collection. Upon addition of 10 mg l(-1) of nanosilica to wastewater effluent samples, the measured photon count rates were within 5% of the estimated values. The results indicated that photon count rate data can effectively complement various techniques currently available to detect nanoscale particles in wastewaters.     

Summer time haze characteristics of the urban atmosphere of Gwangju and the rural atmosphere of Anmyon, Korea

An extensive visibility monitoring was carried out simultaneously in the urban area of Gwangju and the rural area of Anmyon, Korea. This study examines patterns of visibility impairment and haze-forming pollutant concentrations on both sites resulting from natural and anthropogenic sources of gases and particles. Optical visibility measurements by a transmissometer, a nephelometer and an aethalometer provide aerosol light extinction, scattering, and absorption coefficients for both sites. In order to investigate the physico-chemical characteristics of atmospheric aerosols, aerosol samples were collected by various aerosol samplers at GJVMS (Gwangju Visibility Monitoring Station) and at KGAWO (Korea Global Atmosphere Watch Observatory), respectively. In addition, haze characteristics causing visibility impairment at those two sites were analyzed to obtain source contributions by regionally transported aerosols using grid analysis and display system (GrADS) from NECP reanalysis data. During the intensive monitoring period, ammonium sulfate was dominantly responsible for the fine particle mass loading at GJVMS, whereas organic carbon was the largest contributor at KGAWO. Light scattering by particles accounted for 52.8 to 81.3% of the range at the urban site, GJVMS and for 72.1 to 94.2% of the range at the rural site, KGAWO. Light absorption by the EC and NO₂ was between 14.5 and 34.8% at GJVMS, which was higher than the observed 1.1 ∼ 6.8% at KGAWO, respectively. Light scattering by aerosol was higher in the rural area than in the urban area. And organic carbon concentration was observed to be significantly higher than the concentration of elemental carbon at KGAWO. These haze-forming carbonaceous particles originate from anthropogenic pollutants at the urban atmosphere but they can be produced by natural environments such as marine and forest at the rural atmosphere.     

Monitoring of ambient particles and heavy metals in a residential area of Seoul, Korea

In this study, ambient TSP, PM10, and PM2.5 in a residential area located in the northern part of Seoul were monitored every other month for 1 year from April 2005 to February 2006. The monthly average levels of TSP, PM10, and PM2.5 had ranges of 71∼158, 40∼106, and 28∼43 μg/m³, respectively. TSP and PM10 showed highest concentration in April; this seems to be due to Asian dust from China and/or Mongolia. However, the fine particle of PM2.5 showed a relatively constant level during the monitoring period. Heavy metals in PM 10 and PM2.5, such as Cr, As, Cd, Mn, Zn and Pb, were also analysed during the same period. The monthly average concentrations of heavy metal in PM2.5 were Cr:1.9∼22.7 ng/m³; As:0.9∼2.5 ng/m³; Cd: 0.6∼7 ng/m³; Mn:6.1∼22.6 ng/m³; Zn: 38.9∼204.8 ng/m³, and Pb: 21.6∼201.1 ng/m³. For the health risk assessment of heavy metals in ambient particles, excess cancer risks were calculated using IRIS unit risk. As a result, the excess cancer risks of chromium, cadmium, and arsenic were shown to be more than one per million based on the annual concentration of heavy metals, and chromium showed the highest excess cancer risk in ambient particles in Seoul.     

Concentrations of PM2.5-associated OC, EC, and PCDD/Fs measured during the 2003 wildfire season in Missoula, Montana

Throughout August and September, 2003, wildfires burned in close proximity to Missoula, Montana, with smoke emanating from the fires impacting the valley for much of the summer. This presented the perfect opportunity to measure the levels of polychlorinated dibenzodioxins and dibenzofurans (PCDD/F) comprising ambient forest fire smoke particles impacting the Missoula Valley. An air sampler at the Montana Department of Environmental Quality's (DEQ) compliance site in Missoula measured hourly averages of PM₁₀ throughout the fire season. Three collocated PM_2.5 cyclones collected 24-h smoke samples using quartz filters and Polyurethane Foam (PUF) sorbent cartridges. From the quartz filters, concentrations of Organic and Elemental Carbon (OC/EC) were measured, while PCDD/F were measured from one set of a filter (particle phase) and PUF (vapor phase) aggregate of samples in an attempt to also investigate the different phases of PCDD/F in forest fire smoke impaired communities.Hourly PM₁₀ concentrations peaked at 302.9 μg m⁻³ on August 15. The highest OC concentration (115.6 μg m⁻³) was measured between August 21–22, and the highest EC concentration of 10.5 μg m⁻³ was measured August 20–21. Measurable concentrations of PM_2.5 associated PCDD/Fs were not detected from a representative aggregate sample, with the exception of small amounts of 1,2,3,4,6,7,8-heptachlorodibenzodioxin and octachlorodibenzodioxin. PM_2.5 samples collected during the smoke events were composed of approximately 65% OC. However, the OC fraction of the particles collected in the smoke impaired Missoula valley was not composed of significant amounts of PCDD/F.     

考虑道路扬尘特性的环境空气质量在线监测方法

为判断环境空气污染的程度,提出一种考虑道路扬尘特性的环境空气质量在线监测方法。通过前端数据监测模块采集大气环境数据,基于光全散射法监测道路扬尘的质量浓度和密度;通过监测通信模块将监测结果传送至云服务器;云服务器利用基于极限学习机神经网络的预测模型,采用自适应粒子群优化算法,获取最佳的环境空气质量在线监测结果。结果表明,该方法学习速率的取值为0.5时,能够完成颗粒物浓度和密度的准确检测,且解释方差<2%,同时能够监测扬尘颗粒的扩散时间,确定适合活动的区域。     

Ambient Aerosol and its Carbon Content in Gainesville, a Mid-Scale City in Florida

Ambient aerosols were collected during 2000–2001 in Gainesville, Florida, using a micro-orifice uniform deposit impactor (MOUDI) to study mass size distribution and carbon composition. A bimodal mass distribution was found in every sample with major peaks for aerosols ranging from 0.32 to 0.56 μm, and 3.2 to 5.6 μm in diameter. The two distributions represent the fine mode (<2.5 μm) and the coarse mode (>2.5 μm) of particle size. Averaged over all sites and seasons, coarse particles consisted of 15% carbon while fine particles consisted of 22% carbon. Considerable variation was noted between winter and summer seasons. Smoke from fireplaces in winter appeared to be an important factor for the carbon, especially the elemental carbon contribution. In summer, organic carbon was more abundant. The maximum secondary organic carbon was also found in this season (7.0 μg m⁻³), and the concentration is between those observed in urban areas (15–20 μg m⁻³) and in rural areas (4–5 μg m⁻³). However, unlike in large cities where photochemical activity of anthropogenic emissions are determinants of carbon composition, biogenic sources were likely the key factor in Gainesville. Other critical factors that affect the distribution, shape and concentration were precipitation, brushfire and wind.     

激光散射法和便携式氢火焰离子化检测器法直读监测油烟排放

餐饮业油烟排放具有排放浓度不稳定、波动较大、排放时间短等特性，存在瞬时排放高值现象，油烟"看得见"和"闻得着"的问题依然存在，因此对油烟实现快速、及时、直读监测尤为必要。基于一种浓度可控且稳定的油烟产生技术，对直读激光散射法与经典手工称重法测定油烟颗粒物浓度值的数据线性关系进行了分析，发现2种方法数值的相关系数达0.99，通过直读修正激光散射法可以有效地测定油烟颗粒物浓度，并测定了不同水汽含量下油烟颗粒物排放情况，发现当相对湿度超过70%时，油烟颗粒物浓度测定值会发生突变。使用便携式氢火焰离子化检测器法（FID）和光离子化检测器法（PID）测定了不同油温下油烟中非甲烷总烃（NMHC）浓度，发现FID对油烟中NMHC的变化反应及时，能够较好地测定油烟中挥发性有机物的排放量。     

提高TEOM数据准确性和有效率的方法

基于振荡天平法颗粒物自动监测仪器在实际应用中存在的问题,在分析其工作原理的基础上,提出了增加光散射组件的辅助方案。实测结果表明：两者结合可以提高仪器检测数据的准确性和有效率,增强仪器的稳定性和可靠性,使仪器更加"皮实耐用"。     

不同气团来源对广州细颗粒物理化特性的影响

利用2006年7月广州细颗粒物质量浓度、数谱分布与化学组成的观测数据与气团后向轨迹聚类分析结果,系统分析了不同气团来源对广州细颗粒物理化特性的影响。观测期间,广州气团来源可分成来自远海、近海、西面陆地和北面陆地4种类型。细颗粒物总数浓度水平在4种类型中基本相当。当气团来自远海时,二次转化影响较小,PM2.5质量浓度较低,颗粒物数浓度从大到小依次为老化爱根核模态新鲜爱根核模态度积聚模态;受到海洋气团的影响,Cl-在PM2.5中比例为4种类型中最大。气团来自近海时,颗粒物二次生成与老化现象突出,数谱峰值出现在积聚模态,而其他类型出现在爱根核模态;SO2-4、OC与NO-3之和在PM2.5中的比例大于50%,为4种类型中最高。气团来自西面陆地和北面陆地时,细颗粒物受陆地传输老化气团和本地来源影响均较明显。来自北面陆地时,250 nm以上颗粒物数浓度明显升高,是PM2.5平均浓度远高于其他类型的直接原因之一。     

Submicron particle characteristics of atmospheres in a long highway tunnel

This study used a scanning mobility particle sizer (SMPS) to measure and categorize submicron atmospheric particles in the 14–737-nm size range for ambient and urban roadside air and for air in the Hsuehshan Tunnel (12.9 km), Taiwan. Principal component analysis, traffic flow, and particle size distributions were used to identify the emission characteristics of light-duty vehicles (LDV) with the SMPS data. In the Hsuehshan Tunnel, the particle size from the majority of emissions discharged by LDV is approximately 20–60 nm, and the maximum particle number can reach up to 2.5?×?10⁵. In contrast, submicron particle size distribution for urban roadsides is mostly 14–200 nm, and the maximum particle number is approximately 4?×?10⁴ with the particle number for most particle sizes being below 1,200. The submicron particle size distribution at the ambient air station was unimodal with a mode sizes at 30–50 nm with the maximum particle number of 3,000.