Determination of CH4, CO2 and N2O in air samples and soil atmosphere by gas chromatography mass spectrometry, GC-MS

A method for determination of the climate gases CH4, CO2 and N2O in air samples and soil atmosphere was developed using GC-MS. The method uses straightforward gas chromatography (separation of the gases) with a mass spectrometric detector in single ion mode (specific determination). The gases were determined with high sensitivity and high sample throughput (18 samples h(-1)). The LOD (3sigma) for the gases were 0.10 micro L L(-1) for CH4, 20 microL L(-1) for CO2 and 0.02 microL L(-1) for N2O. The linear range (R2 = 0.999) was up to 500 microL L(-1) for CH4, 4000 microL L(-1) for CO2 and 80 microL L(-1) for N2O. The samples were collected in 10 mL vials and a 5 microL aliquot was injected on column. The method was tested against certified gas references, the analytical data gave an accuracy within +/-5% and a precision of +/-3%. The presence of < or = 10% by volume of C2H2 (often used experimentally to prevent N2 formation from N2O) did not interfere with detection for the targeted trace gases.     

Implementing infrared determination of quartz particulates on novel filters for a prototype dust monitor

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized filter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM). Standard fiberglass TEOM filters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel filter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon fiber candidate filters left minimal residual ash and produced no significant spectral interference. Avoiding titanium dioxide in all filter materials proved to be a key requirement. Fine quartz particulates were collected on prototype filters in a Marple chamber, either open-faced or through PDMs during test runs. The filters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to filter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in filter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM filters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7-10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM filters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.     

The application of HPLC-F and GC-MS to the analysis of selected hydroxy polycyclic hydrocarbons in two certified fish bile reference materials

Four selected hydroxy polycyclic aromatic hydrocarbons (OH-PAHs), 2-hydroxy-naphthalene (2-OH-NPH), 1-hydroxy-phenanthrene (1-OH-PHE), 1-hydroxy-pyrene (1-OH-PYR) and 3-hydroxy-benzo[a]pyrene (3-OH-BaP) have been analysed in two certified fish bile reference materials (CRMs) for exposure monitoring of PAHs in the aquatic environment. The two materials, BCR 720 and BCR 721, consist of bile from fish exposed to contaminated sediment and dispersed crude oil, respectively. Both bile samples have been analysed by two different analytical techniques, gas chromatography-mass spectrometry (GC-MS) and high performance liquid chromatography-fluorescence detection (HPLC-F), and the separation performance, detection limits, recoveries and reproducibility for the four target compounds were evaluated. HPLC-F requires a simple sample preparation and the separation capacity is adequate for quantification of 1-OH-PYR and 3-OH-BaP. Detection limits are excellent for 1-OH-PYR (6 pg injected) and 3-OH-BaP (3 pg injected) and generally improved with increasing molecular size. Recoveries ranged from 48 to 99% for the four selected compounds, depending on compound and concentration. Sample preparation prior to GC-MS analysis was more demanding, as reflected by the obtained recoveries for 2-OH-NPH, 1-OH-PHE and 1-OH-PYR (35 to 61%). The sensitivity improved with decreasing molecular size, 2-OH-NPH (1.2 pg injected), 1-OH-PHE (2.4 pg injected) and 1-OH-PYR (6 pg injected). Because of the superior separation power of GC and the extra selectivity of MS detection, GC-MS was the method of choice for the determination of 2-OH-NPH and 1-OH-PHE in both CRMs. In fish bile samples these two compounds are more likely to suffer from chromatographic overlap, and HPLC-F was not sufficiently selective. Determination of 1-OH-PYR was performed with success by both methods, but HPLC-F would be preferred because of the simpler and less time-consuming sample preparation. Detectable concentrations of 3-OH-BaP were present in BCR 720 and could only be determined by HPLC-F. The present work aims to present HPLC-F and GC-MS as complementary methods for the quantitative analysis of OH-PAHs in fish bile.     

A multiresidue method for the analysis of phenols and nitrophenols in the atmosphere

A method using GC-MS and derivatization with N-(t-butyldimethylsilyl)-N-methyltrifluoroacetamide (MTBSTFA) was developed for the analysis of 20 phenolic compounds in atmospheric samples (gas and particles). Air sampling was carried out using a Hi-Vol sampler with glass fibre filter and XAD-2 resin at a flow rate of 60 m(3) h(-1). The particle and gas phases were collected separately over a period of 4 h. Samples were Soxhlet extracted, evaporated to dryness under nitrogen and refilled with acetonitrile. 100 microl of these extracts were derivatized with 100 microl of MTBSTFA at 80 degrees C for 1 h under strong stirring. Phenolic compounds were injected into a GC-MS in splitless mode and quantified as their TBDMS derivatives in the SIM mode. Mass spectral analysis of the derivatives of the 20 compounds studied indicates that the spectra are highly specific showing an ion at [M - 57]+ which is useful for structure confirmation or analysis at low levels using selected ion monitoring. Quantification limits varied between 5 microg l(-1) and 10 microg l(-1) which correspond to 20 pg m(-3) and 40 pg m(-3) for 250 m(3) of air sampled. This method was successfully applied to atmospheric samples.     

Evaluation of a fast wastewater odour characterisation procedure using a chemical sensor array

Sewage treatment works are one of the major sources that cause atmospheric odour pollution. The increase in the number of complaints about odour nuisance is due to the increase in environmental concerns. Unfortunately, the legislation on odour nuisance from sewage treatment works is very limited. In order to determine suitable thresholds on which to base legal standards, reliable and efficient odour measurement methods need to be defined. A chemical sensor array was developed for the purpose of measuring wastewater odour. This paper describes the development of the chemical sensor system which is specifically tuned to odours of wastewater origin and which can give an electronic measure of the wastewater odours. Odour emissions from a wastewater treatment facility were detected by using a quartz crystal microbalance (QCM) sensor array. The array consists of nine sensor elements, which were coated with different materials. In this paper, the usage of these novel instruments in the water industry was shown.     

便携式GC-MS测定气体样品中6种典型VOCs的不确定度评定

以便携式GC-MS测定气体样品中6种典型挥发性有机物(VOCs)组分(苯、1,1,2-三氯乙烷、四氯乙烯、乙苯、间二甲苯和1,3,5-三甲基苯)为例,应用不确定度理论,从检测过程和计算方法的角度分析了影响测量不确定度的各种因素:标准气体定值、标准气体稀释、工作曲线的非线性及重复性测定.对各测量不确定度分量进行计算和评定...     

Identification and quantification of bisphenol A by gas chromatography and mass spectrometry in a lab-scale dual membrane system

Endocrine disruptor contamination is an emerging issue of concern in the field of water quality engineering. In this study, a lab-scale microfiltration (MF) and reverse osmosis (RO) based water reclamation system was set up to monitor and evaluate the removal of bisphenol A (BPA), which is a known oestrogenic compound. The identification and quantification of BPA were performed by using gas chromatography coupled with mass spectrometry. It was noted that the detection method used in this study was able to achieve an average recovery ranging from 88.2 to 94.1% of BPA with standard deviations of less than 10% in different spiked samples. The detection limit of the analytical protocol was determined at 20 ng L(-1). Based on the analytical protocol, it was noted that a low level of BPA (1.18-3.04 microg L(-1)) could be detected in feed water (effluent of an activated sludge treatment system) to the dual membrane water reclamation system. The results obtained suggested that BPA could be easily chlorinated by sodium hypochlorite with a dosage of 4 to 5 mg L(-1) and a contact time of 1 to 2 min. In this lab-scale study, a satisfactory removal of BPA was readily obtained by RO and BPA was abated to an undetectable level in the product water. It was noted that the RO rejection characteristic of BPA was not sensitive to the variations in raw feed water characteristics experienced in this study. In addition, it was noted that BPA concentration present in raw feed water did not exert any significant impact on RO performance in terms of BPA rejection. The results of this study demonstrated that membrane technology could be effectively used for BPA removal.     

Capillary microextraction for simultaneous analysis of multi-residual semivolatile organic compounds in water

Capillary microextractor (CME) in combination with a gas chromatograph-mass spectrometer (GC-MS) was employed for the determination of trace priority hazardous substances in water. Three groups of semivolatile organic compounds (SVOCs), i.e., chlorinated hydrocarbons, pesticides and polycyclic aromatic hydrocarbons (PAHs), were simultaneously determined. SVOCs were extracted from 7 mL of water samples on a 100 cm commercial gas chromatographic column (0.32 mm id x film thickness 0.25 microm, HP-5 capillary column) and eluted with only 3 microL of acetonitrile. The extractant was analyzed by GC-MS in the selected ion monitoring mode. The method showed good linearity over the concentration range 10 ng L(-1) to 3.0 mg L(-1) with correlation coefficients (r) greater than 0.99 and low limits of detection ranged from 10 ng L(-1) to 1.0 mg L(-1). High recovery (more than 80%) was obtained with relative standard deviation less than 10%. The method was successfully applied for trace level analyses of SVOCs in water samples.     

电感耦合等离子体原子发射光谱法测定废气中的铅方法研究

以石英纤维滤筒采样,采用硝酸一氢氟酸消解体系,建立了电感槌合等离子体原子发射光谱法测定废气中铅分析方法。研究了仪器工作条件、方法的干扰和消除因素,探讨了空白实验对分析结果的影响;在选定的最优条件下。铅标准曲线的线性相关系数为0．9999;检出限为0．010mg／L;平均相对标准偏差为2．8％;加标回收率为97．8％～104％。与国家标准方法相比,本方法准确可靠,检测限更低,灵敏度更高,线性范围更宽,可用于废气中铅的含量测定。     

Examples of the role of analytical chemistry in environmental risk management research

Analytical chemistry is an important tier of environmental protection and has been traditionally linked to compliance and/or exposure monitoring activities for environmental contaminants. The adoption of the risk management paradigm has led to special challenges for analytical chemistry applied to environmental risk analysis. Namely, methods developed for regulated contaminants may not be appropriate and/or applicable to risk management scenarios. This paper contains examples of analytical chemistry applied to risk management challenges broken down by the analytical approach and analyte for some selected work in our laboratory. Specific techniques discussed include stable association complex electrospray mass spectrometry (cESI-MS), gas chromatography-mass spectrometry (GC-MS), split-flow thin cell (SPLITT) fractionation and matrix-assisted laser desorption time of flight mass spectrometry (MALDI-ToF-MS). Specific analytes include haloacetic acids (HAA9), perchlorate, bromate, triazine degradation products, metal-contaminated colloids and Cryptosporidium parvum oocysts.     

Determination of N-acetyl-S-(N-methylcarbamoyl)cysteine (AMCC) in the general population using gas chromatography-mass spectrometry

Carbamoylation of glutathione, peptides and DNA is thought to be one of the most important reactions occurring in an organism after exposure to nitrosoureas, methylformamides or isocyanates. The carcinogenic effects of carbamoylation are not yet fully clarified. Although carbamoylation is known to occur after occupational exposure, it has never been reported in the general population. To clarify the situation, we investigated the levels of N-acetyl-S-(N-methylcarbamoyl)cysteine (AMCC) in urine samples from persons without occupational exposure using a sensitive and specific method (gas chromatography-mass spectrometry, GC-MS). AMCC is the degradation product of N-methylcarbamoylated glutathione. The clean-up procedure of urine samples includes two liquid-liquid extraction steps and solid phase extraction using a cation-exchange resin to separate AMCC from other urinary components. N,N-Dimethylpropionic acid amide (DMPA) is used as internal standard. During the preparation of the samples, AMCC is converted to ethyl-N-methylcarbamate (EMC) in the presence of anhydrous potassium carbonate (K2CO3) and ethanol. The reliability and accuracy of this method have been proven in detail. The relative standard deviation for the within-series imprecision for three different concentrations was determined to be between 10.9% and 14.3%, while the relative standard deviation for the between-day imprecision was between 11.3% and 14.8%. The mean recovery for AMCC was determined to be between 79.2% and 85.6%. The limit of detection for the simultaneous measurement of two fragment masses was 30 micrograms L-1. Using this GC-MS method, we analysed urine samples from 42 individuals of the general population in order to determine their urinary excretion of AMCC. It was identified in 40 samples. The mean concentration was 40 micrograms L-1. AMCC can be formed in two ways. The first possibility is the dietary intake of isothiocyanates, especially methyl isothiocyanate, which is a component of wine and cruciferous vegetables (such as cabbage, turnips and cress). During the metabolism of isothiocyanates in humans, the sulfur is partly exchanged for oxygen resulting in the formation of the corresponding isocyanate derivatives. The other possibility is the physiological formation of AMCC. In humans, this may occur via a two step process: carbamoylation and methylation, or vice versa. However, as AMCC was identified in about 95% of urine samples, and the standard deviation for the level of AMCC excreted was low, physiological formation seems to be the more probable pathway.     

Quantification of bacterial lipopolysaccharides (endotoxin) by GC-MS determination of 3-hydroxy fatty acids

A GC-MS method for the quantification of bacterial lipopolysaccharides (LPS, endotoxin) is presented. After hydrolytic cleavage of 3-hydroxy fatty acids (3-OH FAs) from the lipid A region of LPS, derivatisation of both the hydroxyl and the carboxyl group was performed in one step with a mixture of methyl-bis(trifluoracetamide)(MBTFA) and N-methyl-N-(tert-butyldimethylsilyl)trifluoracetamide (MTBSTFA). Using GC-MS in the EI mode with selected ion monitoring (SIM) for analysis, baseline separation of 3-OH FAs (and of possibly interfering 2-OH FAs) was achieved. The sensitivity of the method (LOD 7-50 pg/injection for the different 3-OH FAs investigated) allows for the efficient quantification of LPS in occupational and environmental samples. Degradation of 3-OH FAs as well as of their derivatives during sample preparation and GC-MS separation as a possible source of errors in analytical methods based on 3-OH FA determination is reported for the first time. Thermal elimination of water from the underivatised 3-OH FAs and of trifluoroacetic acid from the derivatives was identified as the cause of degradation. The resulting alpha,beta-unsaturated compounds showing the same mass spectra as the 3-OH FA derivatives were detected as more or less prominent satellite peaks. By using alkaline instead of acidic hydrolysis and cool on-column instead of split/splitless injection, elimination was reduced to an acceptable level.     

Community air monitoring for pesticides—part 2: multiresidue determination of pesticides in air by gas chromatography,gas chromatography–mass spectrometry,and liquid chromatography–mass spectrometry

Two multiresidue methods were developed to determine pesticides in air collected in California. Pesticides were trapped using XAD-4 resin and extracted with ethyl acetate. Based on an analytical method from the University of California Davis Trace Analytical Laboratory, pesticides were detected by analyzing the extract by gas chromatography–mass spectrometry (GC-MS) to determine chlorothalonil, chlorthal-dimethyl, cycloate, dicloran, dicofol, EPTC, ethalfluralin, iprodione, mefenoxam, metolachlor, PCNB, permethrin, pronamide, simazine, trifluralin, and vinclozolin. A GC with a flame photometric detector was used to determine chlorpyrifos, chlorpyrifos oxon, diazinon, diazinon oxon, dimethoate, dimethoate oxon, fonophos, fonophos oxon, malathion, malathion oxon, naled, and oxydemeton. Trapping efficiencies ranged from 78 to 92 % for low level (0.5 μg) and 37–104 % for high level (50 and 100 μg) recoveries. Little to no degradation of compounds occurred over 31 days; recoveries ranged from 78 to 113 %. In the California Department of Food and Agriculture (CDFA) method, pesticides were detected by analyzing the extract by GC-MS to determine chlorothalonil, chlorpyrifos, cypermethrin, dichlorvos, dicofol, endosulfan 1, endosulfan sulfate, oxyfluorfen, permethrin, propargite, and trifluralin. A liquid chromatograph coupled to a MS was used to determine azinphos-methyl, chloropyrifos oxon, DEF, diazinon, diazinon oxon, dimethoate, dimethoate oxon, diuron, EPTC, malathion, malathion oxon, metolachlor, molinate, norflurazon, oryzalin, phosmet, propanil, simazine and thiobencarb. Trapping efficiencies for compounds determined by the CDFA method ranged from 10 to 113, 22 to 114, and 56 to 132 % for 10, 5, and 2 μg spikes, respectively. Storage tests yielded 70–170 % recovery for up to 28 days. These multiresidue methods represent flexible, sensitive, accurate, and cost-effective ways to determine residues of various pesticides in ambient air.     

Occurrence and behaviour of 4-nonylphenol in river water of Germany

An analytical method composed of solid-phase-extraction (SPE) followed by gas chromatography-mass spectrometry (GC-MS) has been developed to investigate the occurrence and the behaviour of the endocrine disruptor 4-nonylphenol (4-NP) in river water of Germany. 16 Para-isomers of the complex mixture of 4-NP isomers have been resolved in the SPE-extracts of river water samples. The mass spectra indicate the presence of four distinct groups of isomers. The different groups are characterised by different base peaks of the mass spectra dependent on the substitution of the alpha-carbon on the alkyl chain. The different isomers show (i) alpha-methyl, alpha-ethyl (base peak 149), (ii) alpha-dimethyl (base peak 135), (iii) alpha-methyl, alpha-propyl, alpha-butyl (base peak 121) and (iv) alpha-methyl, alpha-propyl, alpha-butyl (base peak 107) configuration of the alkyl chain. The recovery of the unbranched compound 4-n-NP was > or = 90%. Detection limit and determination limit of the whole analytical procedure were 6 ng L(-1) and 25 ng L(-1), respectively with a relative standard deviation of 11.7%. The concentration of the sum of the 4-NP isomers in all samples of river water ranged from 28 ng L(-1) (Elbe River) to 1220 ng L(-1)(Oder River). In a period of a higher river water level, a higher amount of 4-NP was detected in the Oder River than in a period of a lower water level. Therefore dilution was not the determinant factor of the 4-NP concentration in river water. The diurnal dynamics of the sewage treatment works (STWs) have to be considered as an influencing factor for the presence of 4-NP in river water.     

加速溶剂萃取-气相色谱/串联质谱法测定土壤中20种有机氯农药

建立了用加速溶剂萃取法（ASE）提取、气相色谱-串联质谱法分析土壤中20种有机氯农药的方法。用正己烷和丙酮（1∶1,V/V）的混合溶剂为提取剂,萃取温度100℃,压力1 500 psi,静态提取10 min,循环提取2次,提取液经石墨化碳黑固相萃取柱净化,浓缩后进行GC-MS/MS测定,外标法定量。试验结果表明,采用串联质谱多反应监测模式,降低了背景干扰,当取5 g土壤时,有机氯农药的检出限在0.1~3.0μg/kg之间,低浓度水平（8μg/kg）的基体加标回收率为70.3%~134%,相对标准偏差〈23%。测定方法背景干扰低,灵敏度高,适合土壤中20种有机氯农药残留的同时测定。     

气相色谱-质谱法快速筛查气态制冷剂产品中的热点管控类卤代烃

建立了利用气相色谱-质谱法快速筛查气态制冷剂产品中的10种热点管控类卤代烃的分析方法。采用气密性微量注射器对气态制冷剂样品进行取样,刺透瓶盖隔垫加入到顶空瓶中,自动进样;以GS-GasPro(多孔层开管,60 m×0.32 mm)为色谱柱,采用电子轰击离子源,全扫描模式采集。测试结果显示:目标物的体积分数在0.50%~100.00%范围内,相对响应因子的相对标准偏差(RSD)均小于20%;线性相关系数r均在0.999以上;检出限(3.143倍标准偏差)为0.01%~0.05%。对实际样品进行加标回收,回收率为79.5%~102%,测定值RSD为0.5%~3.1%。该方法可为快速、准确、批量筛查气态制冷剂产品中的多种热点管控类卤代烃提供技术支撑。     

Assessment of organochlorine pesticide residues in Indian flue-cured tobacco with gas chromatography-single quadrupole mass spectrometer

Presence of pesticide residues in tobacco increases health risk of both active and passive smokers, apart from the imminent potential health problems associated with it. Thus, monitoring of pesticide residue is an important issue in terms of formulating stringent policies, enabling global trade and safeguarding the consumer’s safety. In this study, a gas chromatography-single quadrupole mass spectrometry (GC-MS) method based upon quantifier-qualifier ions (m/z) ratio was employed for detecting and assessing ten organochlorine pesticide residues (α-HCH, β-HCH, γ-HCH, δ-HCH, 2,4-DDT, 4,4-DDT, endrin, α-endosulfan, β-endosulfan and endosulfan sulphate) in 152 flue-cured (FC) tobacco leave samples from two major tobacco growing states, Karnataka and Andhra Pradesh, of India. In the majority of samples, pesticide residue levels were below the limit of quantification (LOQ). In few samples, pesticide residues were detected and they found to comply with the guidance residue levels (GRL) specifications of the Cooperation Center for Scientific Research Relative to Tobacco (CORESTA). Detection of the phase out pesticides like DDT/HCH might be due to transfer of persistent residues from the environmental components to the plant. This is the first report on these ten organochlorine pesticide residues in Indian FC tobacco.     

Influences of metal cations on the determination of the alpha-oxocarboxylates as the methyl esters of the O-(2,3,4,5,6-pentafluorobenzyl)oximes by gas chromatography: the importance of accounting for matrix effects

The alpha-oxocarboxylates alpha-ketocarboxylates) and the corresponding alpha-oxoacids (alpha-ketoacids) have been reported as disinfection byproducts of ozonation of potable water supplies. In this analytical method, the oxo moiety is derivatized with O-(2,3,4,5,6-pentafluorobenzyl)oxylamine (PFBOA) to form an oxime which is then extracted into tert-butyl methyl ether. The carboxylic acid moiety is esterified (methylated) with diazomethane. In this study, five analytes were investigated: oxoethanoate (glyoxylate), 2-oxopropanoate (pyruvate), 2-oxobutanoate (2-ketobutyrate), 2-oxopentanoate (2-ketovalerate), and oxopropanedioate (ketomalonate, mesoxalate). The influence of Lewis acid metal cations in the water matrix was evaluated for the gas chromatographic method commonly used for the quantitation of these analytes at concentrations < or = 150 ng mL(-1). Tested metals included Ca(II), Mg(II), Fe(III), Cu(II) and Zn(II). At typical concentrations, calcium, in particular, can have profound impact, especially on oxoethanoate quantitation. Oxopropanoate experiences an increase in recovery in the presence of metal cations. 2-Oxobutanoate and 2-oxopentanoate are the most resistant to these effects, but 2-oxopentanoate shows increased recoveries at higher concentrations when assayed in the presence of calcium ion. Oxopropanedioate generally shows poorer precision and recovery when determined in solutions containing metal ions. This investigation demonstrates the significance of metal effects in the quantitative determination of these analytes and further emphasizes the importance of thorough matrix characterization and careful recovery studies with fortified (spiked) samples and blanks.     

LLE-GC-MS法测定水中27种有机农药

建立了同时测定水中27种有机农药的LLE-GC-MS法。该法前处理前需调节水样pH值2,不加甲醇作为改性剂,以1:1(V/V)正己烷-石油醚为萃取溶剂进行液液萃取,GC-MS法进行检测。方法在各目标化合物质量浓度0.010~0.500 mg/L范围内线性良好,相关系数R2均0.995,检出限为0.021~0.250μg/L,加标回收率为73.6%~113.6%,相对标准偏差RSD为4.0%~14.1%,适用于水中27种有机农药的检测。     

质谱及其联用技术在水中消毒副产物识别和分析中的应用

水中消毒副产物(DBPs)是在水消毒过程中消毒剂与水中溶解性有机物以及无机离子发生反应而产生,其对水环境生态安全和人体健康有不利影响。简述了DBPs的生成、种类、毒性和分析方法等,重点综述了气相色谱-质谱联用(GC-MS)、液相色谱-质谱联用(LC-MS)、离子色谱-质谱联用(IC-MS)以及超高分辨率质谱(UPMS)等质谱(MS)及其联用技术在水中DBPs识别和分析中的应用,分析了不同MS技术的特点和应用实例,提出了MS技术在DBPs研究领域的发展方向与挑战。