波长色散-X射线荧光光谱法测定PM2.5中23种元素

研究以单元素标准膜为基础,结合NIST SRM 2783颗粒物滤膜标准样品,建立了波长色散-X射线荧光光谱法测定PM_2.5中23种无机元素的测定方法,优化了测试条件,测量一个样品耗时约15 min,计算了各元素的方法检出限。对NIST SRM 2783滤膜标准品在一周内重复测定10次来计算方法的准确度与精密度,测定结果显示大多数元素的测量值在给出的参考值范围内,且测量标准偏差一般在10%以内。对比了石英与聚四氟乙烯材质（Teflon）滤膜的空白值,石英滤膜中Si、Fe、Na、Mg、Al、K、Ca等元素的背景值较高,Teflon滤膜的背景值较低,推荐选用Teflon滤膜作为PM_2.5组分分析采样滤膜。分别用波长色散-X射线荧光光谱法及酸消解-ICP-MS法测定了样品膜中的元素组分,得到的测定结果基本一致。     

Heavy Metals Content in N. OleanderLeaves As Urban Pollution Assessment

Nerium oleanderL. (Oleander) leaves grown in Palermo city (Sicily, Italy) were collected from six sampling sites representing either areas of high traff{i}c and urbanisation density or areas far away from traffic (e.g. city gardens). Concentration of Al, Ba, Cr, Cu, Fe, Pb, Mg, Mn, and Zn were determined in leaf samples during two years. Multivariate analysis classified the sampling sites in four groups based on the metal content in vegetal leaves in agreement with traffic and human activity site. Many elements studied (Al, Ba, Fe, Mn Mg) arise from the soil composition and others such as Cr, Cu, Pb and Zn as pollutant of the soil. On the other hand, about 30% of Al, Fe Cr, Cu and Pb originate from aerial deposition on leaves. Although the results presented should be handled with caution N. oleandercan be considered as a means of assessing dust contamination in the urban environment.     

大体积水中痕量POPs的联动采集装置及其性能评价

天然水体中的痕量持久性有机污染物(POPs)的定量分析通常需要采集大体积水样.针对大体积水样在过滤和吸附富集过程中滤膜易堵塞且耗时费力的缺点,研制了一种固液分离过滤-吸附富集联动装置.该装置主要由粗过滤器、离心分离屏、倒置微孔过滤器、固相吸附柱、流速控制阀和真空泵组成.与传统的滤膜过滤方式相比,其过滤效率提高了约1.5...     

A comparison of X-ray fluorescence and wet chemical analysis of air filter samples from a scrap lead smelting operation

Personal and area air samples were taken at a scrap lead smelter operation in a bullet manufacturing facility. Samples were taken using the 37-mm styrene-acrylonitrile closed-face filter cassette (CFC, the current US standard device for lead sampling), the 37-mm GSP or "cone" sampler, the 25-mm Institute of Occupational Medicine (IOM) inhalable sampler, and the 25-mm Button sampler (developed at the University of Cincinnati). Polyvinylchloride filters were used for sampling. The filters were pre- and post-weighed, and analyzed for lead content using a field-portable X-ray fluorescence (XRF) analyzer. The filters were then extracted with dilute nitric acid in an ultrasonic extraction bath and the solutions were analyzed by inductively coupled plasma optical emission spectroscopy. The 25-mm filters were analyzed using a single XRF reading, while three readings on different parts of the filter were taken from the 37-mm filters. The single reading from the 25-mm filters was adjusted for the nominal area of the filter to obtain the mass loading, while the three readings from the 37-mm filters were inserted into two different algorithms for calculating the mass loadings, and the algorithms were compared. The IOM sampler was designed for material collected in the body of the sampler to be part of the collected sample as well as that on the filter. Therefore, the IOM sampler cassettes were rinsed separately to determine if wall-loss corrections were necessary. All four samplers gave very good correlations between the two analytical methods above the limit of detection of the XRF procedure. The limit of detection for the 25-mm filters (5 microg) was lower than for the 37-mm filters (10 microg). The percentage of XRF results that were within 25% of the corresponding ICP results was evaluated. In addition, the bias from linear regression was estimated. Linear regression for the Button sampler and the IOM sampler using single readings and the GSP using all tested techniques for total filter loading gave acceptable XRF readings at loadings equivalent to sampling at the OSHA 8-hour Action Level and Permissible Exposure Limit. However, the CFC only had acceptable results when the center reading corrected for filter area was used, which was surprising, and may be a result of a limited data set. In addition to linear regression, simple estimation of bias indicated reasonable agreements between XRF and ICP results for single XRF readings on the Button sampler filters, (82% of the individual results within criterion), and on the IOM sampler filters (77% or 61%--see text), and on the GSP sampler filters using the OSHA algorithm (78%). As a result of this pilot project, all three samplers were considered suitable for inclusion in further field research studies.     

利用自动采样滤膜监测PM_(2.5)中铅和镉的可行性

根据PM2.5中重金属监测国标分析方法,从PM2.5采样方法、采样保存条件、滤膜材质性能等方面说明利用空气自动采样滤膜监测PM2.5中铅和镉是可行的;对手工采样(石英滤膜)和Beta射线法自动采样(自动采样滤膜)2种方法,对PM2.5实际样品中铅和镉的结果进行比较,结果显示:自动采样滤膜的空白检出和检出限均满足铅和镉的监测需求,铅和镉的回收率分别为95.2%~107%和91.8%~105%,与手工采样方法相比测得铅和镉的相对误差分别为3.6%~8.4%和1.3%~10.8%,从实践角度进一步证明了利用自动采样滤膜对PM2.5中铅和镉进行监测是可行的。     

Portable XRF analysis of occupational air filter samples from different workplaces using different samplers: final results, summary and conclusions

This paper concludes a five-year program on research into the use of a portable X-ray fluorescence (XRF) analyzer for analyzing lead in air sampling filters from different industrial environments, including mining, manufacturing and recycling. The results from four of these environments have already been reported. The results from two additional metal processes are presented here. At both of these sites, lead was a minor component of the total airborne metals and interferences from other elements were minimal. Nevertheless, only results from the three sites where lead was the most abundant metal were used in the overall calculation of method accuracy. The XRF analyzer was used to interrogate the filters, which were then subjected to acid digestion and analysis by inductively-coupled plasma optical-emission spectroscopy (ICP-OES). The filter samples were collected using different filter-holders or "samplers" where the size (diameter), depth and homogeneity of aerosol deposit varied from sampler to sampler. The aerosol collection efficiencies of the samplers were expected to differ, especially for larger particles. The distribution of particles once having entered the sampler was also expected to differ between samplers. Samplers were paired to allow the between-sampler variability to be addressed, and, in some cases, internal sampler wall deposits were evaluated and compared to the filter catch. It was found, rather surprisingly, that analysis of the filter deposits (by ICP-OES) of all the samplers gave equivalent results. It was also found that deposits on some of the sampler walls, which in some protocols are considered part of the sample, could be significant in comparison to the filter deposit. If it is concluded that wall-deposits should be analyzed, then XRF analysis of the filter can only give a minimum estimate of the concentration. Techniques for the statistical analysis of field data were also developed as part of this program and have been reported elsewhere. The results, based on data from the three workplaces where lead was the major element present in the samples, are summarized here. A limit of detection and a limit of quantitation are provided. Analysis of some samples using a second analyzer with a different X-ray source technology indicated reasonable agreement for some metals (but this was not evaluated for lead). Provided it is only necessary to analyze the filters, most personal samplers will provide acceptable results when used with portable XRF analysis for lead around applicable limit values.     

The effect of filter material on bioaerosol collection of Bacillus subtilis spores used as a Bacillus anthracis simulant

The objective of this study was to determine filter materials and extraction methods that are appropriate to use for environmental sampling of B. anthracis. Four types of filters were tested: mixed cellulose ester (MCE) with a pore size of 3 microm, polytetrafluoroethylene (PTFE) with pore sizes of 1 and 3 microm, and gelatin with a pore size of 3 microm. Bacillus subtilis var. niger endospores (also known as Bacillus globigii[BG]) were used as a surrogate for B. anthracis. Endospores were collected into Button Inhalable Aerosol Samplers with sampling times of 15 minutes, 1 hour, and 4 hours. Physical collection efficiency was determined by measuring upstream and downstream B. subtilis concentrations with an optical particle counter. Vortexing with ultrasonic agitation and vortexing with shaker agitation extraction methods were evaluated. The MCE, 1 microm PTFE, and gelatin filters provided physical collection efficiencies of 94% or greater. The 3 microm PTFE filter showed inconsistent physical efficiency characteristics between filters. Epifluorescence microscopic analysis of the gelatin filter extraction fluid revealed the presence of contamination by non-culturable bacteria. Mean differences for microbial culturability were not statistically significant for filter materials and extraction methods. However, the vortexing with shaker agitation extraction method resulted in higher total microbial counts in the extraction fluids for MCE and 1 microm PTFE filters when compared to vortexing with ultrasonic agitation. In summary, the MCE and 1 microm PTFE filters in combination with vortexing and shaker extraction demonstrated the best performance for the filter collection and extraction of BG spores.     

Air sampling of fungal spores on filters. An investigation on passive sampling and viability

In this study, glycerol was tested as a collection substrate for passive bioaerosol sampling. Filters (mixed cellulose acetate and nitrate) were soaked in glycerol and exposed for an aerosol from three different fungal species: Penicillum commune, Aspergillus versicolor and Paecilomyces variotii. The passive sampling method was compared with a closed-face polycarbonate filter sampling method. Exposure was performed in an exposure chamber. The total number of spores was determined by microscopic techniques, and the cultivable number was determined by cultivation on Malt Extract Agar dishes. The glycerol soaked filter demonstrated a good correlation with the closed-face sampler with regard to the total count. Spores stored in a pumped filter cassette were not affected by storage for up to 7 days. On the other hand, the culturability of the spores was markedly decreased after 1 day when stored on glycerol soaked filters.     

Trend in metals variation in Tasik Chini, Pahang, Peninsular Malaysia

Water from 15 sampling stations in Tasik Chini (Chini Lake), Peninsular Malaysia were sampled for 12 months from September 2004 until August 2005 and analyzed for 11 metals including iron (Fe), aluminum (Al), manganese (Mn), barium (Ba), zinc (Zn), lead (Pb), copper (Cu), cadmium (Cd), nickel (Ni), chromium (Cr) and cobalt (Co). Results showed that the mean (min-max) metal concentrations (in micrograms per liter) in Tasik Chini waters for the 12 months sampling based on 15 sampling stations (in descending order) for Fe, Al, Mn, Ba, Zn, Pb, Cu and Cd were 794.84 (309.33-1609.07), 194.53 (62.37-665.93), 29.16 (16.68-79.85), 22.07 (15.64-29.71), 5.12 (2.224-6.553), 2.36 (1.165-4.240), 0.832 (0.362-1.443) and 0.421 (0.254-0.696) respectively. Concentration for three metals i.e. Ni, Cr and Co were too low and not detected by the graphite furnace Atomic Absorption Spectrophotometry (AAS). Comparison with various water quality standards showed that the mean metals concentration in surface water of Tasik Chini were low and within the range of natural background except for Fe and Al. In general, metal concentrations in Tasik Chini water varied temporally and spatially. The main factors influencing these metal concentrations in the water were the raining season and mining activities. Stations located at Tanjung Jerangking and Melai areas were the most effected due to those factors.     

Quantification of re-evaporated mass from loaded fibre-mist eliminators

Airborne lubricant emissions are a serious health hazard for employees in the metal working industry. The basic components of lubricants are oils and additives for adapting the properties to achieve the process demands. The oils used in lubricants are either mineral, synthetic or of biological origin. The lubricants are used as water-emulsions and also as straight oils. Extreme process conditions cause considerable amounts of aerosol and vapour emissions of lubricants into the working environment. Fibre filters are used in industrial demisters for pollution control and also for sampling purposes. Re-evaporation of separated lubricants from loaded fibre filters causes increased vapour emissions. Quantification of lubricant vapour emission was the subject of this research. An apparatus and an appropriate procedure for measuring the dynamic behaviour of evaporative losses from fibre filters were developed. The test piece of a loaded fibre filter was fixed in a sampling probe according to VDI 2066. The vapour concentration of organic compounds in downstream air was measured in real-time by using a photo-ionisation detector (PID). The PID was checked by sampling the vapour on an oleophilic adsorbent resin, solvent extraction and quantitative IR analysis and also gravimetrically. The two basic processes of filtering volatile aerosols are, on the one hand, collecting droplets on the fibres and, on the other hand, the evaporation of collected liquid. These two processes had to be separated in order to measure the increase of the vapour concentration caused by the tested fibre filter. The experiments were carried out using pure dodecane and hexadecane in order to avoid difficulties due to the unknown chemical composition of lubricant vapour. The variation of the air flow and the initial liquid mass on the filter covered the relevant range for industrial fibre demisters and for sampling methods based on collecting aerosols on fibre filters. It was found that the downstream air was saturated with lubricant vapour for a wide range of filter loads and filtration velocities. From the results obtained it can be concluded that loaded industrial filter systems emit air with saturation vapour concentration throughout their operation. Hence, vapour emissions can be estimated easily if the saturation vapour pressure and the mean relative molecular mass are known. Moreover, results obtained from measurements of filters with low loads confirm that the phase transition from liquid to vapour is influenced by the identified process parameters. This is relevant for measurement methods using fibre filters for sampling volatile aerosols. A semi-empirical model to estimate the evaporative losses for low loadings is proposed. However, further research is necessary to determine the full range of parameters that are relevant for evaporative losses from filters loaded with low masses of aerosols.     

Impaction collection and slurry sampling for the determination of arsenic, cadmium, and lead in sidestream cigarette smoke by inductively coupled plasma-mass spectrometry

The slurry sampling technique has been applied for the determination of arsenic, cadmium and lead in sidestream cigarette smoke condensate (SS CSC) by inductively coupled plasma mass spectrometry (ICP-MS). The smoke collection system consists of a "fishtail" chimney in conjunction with an impaction trap and a mixed cellulose ester (MCE) backup filter for the SS CSC collection. The smoke condensates, collected at three different regions of the system (i.e. the inner wall of the chimney, the impaction trap and the MCE filter), were individually prepared and analyzed and showed that about 70 and 20% of Cd and Pb, respectively, were trapped by the impaction trap and the MCE filter with less than 5% trapped by the chimney. In contrast, about 60% of As was trapped by the impactor and a relatively high percentage of As, about 30%, was deposited onto the inner wall of the chimney. The uneven distribution of trace metals at each collection stage strongly suggested that the composition of smoke aerosol and the associated physical form of the analytes may be different. The yields of As, Cd and Pb for the sidestream cigarette smoke of the 1R4F reference cigarette were 29.5 +/- 2.4, 421 +/- 6.6 and 46.4 +/- 0.9 ng cigarette(-1)(n= 3) respectively, when the cigarette was smoked according to the smoking regime: 45 mL puff volume of 2-s puff duration at an interval of 30 s with 50% ventilation holes covered. The analytical results for the slurry sampling technique were also compared with other sample preparation techniques and show good agreement.     

An assessment of the optimal scale for monitoring of MODIS and FIA NPP across the eastern USA

Robust monitoring of carbon sequestration by forests requires the use of multiple data sources analyzed at a common scale. To that end, model-based Moderate Resolution Imaging Spectroradiometer (MODIS) and field-based Forest Inventory and Analysis (FIA) data of net primary productivity (NPP) were compared at increasing levels of spatial aggregation across the eastern USA. A total of 52,167 FIA plots and colocated MODIS forest cover NPP pixels were analyzed using a hexagonal tiling system. A protocol was developed to assess the optimal scale as an optimal size of landscape patches at which to map spatially explicit estimates of MODIS and FIA NPP. The optimal mapping resolution (hereafter referred to as optimal scale) is determined using spatially scaled z-statistics as the tradeoff between increased spatial agreement as measured by Pearson’s correlation coefficient and decreased details of coverage as measured by the number of hexagons. Spatial sensitivity was also assessed using land cover assessment and forest homogeneity using spatially scaled z-statistics. Pearson correlations indicate that MODIS and FIA NPP are most highly correlated when using large hexagons, while z-statistics indicate an optimal scale at an intermediate hexagon size of 390 km². This optimal scale had more spatial detail than was obtained for larger hexagons and greater spatial agreement than was obtained for smaller hexagons. The z-statistics for land cover assessment and forest homogeneity also indicated an optimal scale of 390 km².     

Evaluation of spatial and temporal variations in marine sediments quality using multivariate statistical techniques

Spatial and temporal variations of sediment quality in Matanzas Bay (Cuba) were studied by determining a total of 12 variables (Zn, Cu, Pb, As, Ni, Co, Al, Fe, Mn, V, CO₃ ^2?, and total hydrocarbons (THC). Surface sediments were collected, annually, at eight stations during 2005–2008. Multivariate statistical techniques, such as principal component (PCA), cluster (CA), and lineal discriminant (LDA) analyses were applied for identification of the most significant variables influencing the environmental quality of sediments. Heavy metals (Zn, Cu, Pb, V, and As) and THC were the most significant species contributing to sediment quality variations during the sampling period. Concentrations of V and As were determined in sediments of this ecosystem for the first time. The variation of sediment environmental quality with the sampling period and the differentiation of samples in three groups along the bay were obtained. The usefulness of the multivariate statistical techniques employed for the environmental interpretation of a limited dataset was confirmed.     

Mobilization of aluminium and deposition on fish gills during sea salt episodes--catchment liming as countermeasure

Episodic events may be critical with respect to aluminium (Al) toxicity in moderately acidified salmon rivers. The present work demonstrates that sea salt episodes enhance the toxicity of Al in acidic rivers. The documented sea salt episode (300 [micro sign]M Cl) mobilized positively charged Al species (0.4 to 1.1 [micro sign]M Al(i)), enhanced the Al accumulation on fish gills (0.9 to 10 [micro sign]mol g(-1) dw) and caused increased stress responses (6 to15 mM blood glucose) in fish. Accumulated Al on gills remained high several days after the episode. The presented results are based on a six-week field study in two tributary rivers on the west coast of Norway. Changes in the river water qualities and Al speciation were followed using in situ fractionation techniques. Al accumulation on gills and stress responses were followed for Atlantic salmon (Salmo salar) kept in tanks continually exposed to the changing water quality. The potential mobilization of Al from the two catchments was studied by extracting soils with diluted seawater (salinity of 3). To counteract Al toxicity, one of the tributary catchments has been limed. The potential mobility of Al by sea salt was lower in limed soils compared to acid soils, and the Al deposition on fish gills (<3.5 [micro sign]mol g(-1) dw) and associated stress responses stayed low during the sea salt episode in the river draining the limed catchment. Thus, for acid river systems in coastal areas, catchment liming should be considered as a useful countermeasure for Al toxicity.     

The application of ICP-SMS, GF-AAS and HG-AFS to the analysis of water and sediment samples from a temperate stratified estuary

Three atomic spectrometry techniques, namely sector field inductively coupled plasma mass spectroscopy, graphite furnace atomic absorption spectrometry and hydride generation atomic fluorescence spectroscopy (ICP-SMS, GF-AAS and HG-AFS, respectively), housed at separate independent laboratories, were used to analyse water and sediment samples collected from the Huon River Estuary, SE Tasmania (Australia) in the Austral spring 1998. A dithiocarbamate-chelation/back-extraction technique was used to separate and preconcentrate Co, Ni, Cu, Zn, Cd and Pb from eight collected water samples prior to analysis by ICP-SMS and GF-AAS. A number of other elements in the waters were analysed directly (Mn, Fe and Zn by GF-AAS; As by HG-AFS), or following sample dilution (1 + 19: V, Mn, Fe, As, Mo, Ba and U by ICP-SMS). Where possible, previously corroborated GF-AAS and HG-AFS techniques were used to verify obtained ICP-SMS results. From the analysis of four reference waters (SLEW-1 and -2, SLRS-3 and NASS-5), good agreement, to within +/- 10-20%, was typically found between certified (or information only values) and measured results (irrespective of analytical technique). Exceptions included Zn (and sometimes Fe) that could not be quantified by ICP-SMS due to elevated blank signals, and As which was found to lie below ICP-SMS detection limits. For Huon Estuary water samples, inter-method agreement was within +/- 10-20% (for those elements amenable to analysis by more than one technique). Nitric acid extracts of two certified reference materials (Buffalo River Sediment and BCSS-1) and six Huon Estuary sediments were analysed by ICP-SMS (for Al, Sc, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Cd and Pb) and HG-AFS (for As). Results from the certified reference materials indicated extraction efficiencies of 60 70% (for most elements). A close correlation between ICP-SMS and HG-AFS was obtained for leachable As in the sediments. In terms of potential inorganic contaminants, the Huon Estuary was found to be a relatively 'clean' water system. The elemental concentrations measured in water and sediment samples from this region were found to lie within current Australian guidelines for estuaries. In general, no one analytical technique was able to accurately determine all elements in all samples from this relatively pristine estuarine environment. A combination of all three analytical techniques was necessary for the successful analysis of the elements considered in this study.     

Soil Contribution to the Elemental Composition of Epiphytic Lichens (Tuscany, Central Italy)

Total concentrations of Al, Ba, Cd, Co, Cr, Cu, Fe, Mn, Mo, Pb, Sr, Ti, V and Zn in the epiphytic lichen Parmelia sulcata and superficial soils from 60 remote sampling sites in Tuscany (central Italy) were determined to evaluate the contribution of soil to the elemental composition of the lichen. The results showed that in the Mediterranean environment, the trace element content of unwashed lichen samples is greatly affected by soil contamination. However, despite the strong correlations between the concentrations of lithogene elements such as Al, Fe and Ti in P. sulcata, lichen levels of these elements were not at all linearly correlated with their concentrations in the soil, suggesting that dust contamination is highly variable and probably dependent on local site characteristics. All methods evaluated to minimize soil contamination indicated Cu, Pb and Zn as elements of atmospheric origin. However, while levels of Pb were similar to those reported for background areas, moderate pollution by Cu and Zn, probably from fertilizers used in agriculture, was revealed. For elements such as Cd and Mo, identified as atmophile, some uncertainty exists due to the fact that they are essential for lichen metabolism and accumulate intracellularly in lichens; they may therefore occur in soluble form in the lichen thallus.     

海水中总氮的测定方法比较研究

通过标准曲线、检出限和测定范围、方法精密度、方法准确度、实际海水样品测定结果、加标回收率、分析效率和物料消耗这几方面比较了过硫酸钾氧化法、流动注射分析法和高温氧化-化学发光检测法这3种测定海水中总氮(TN)方法的优缺点。结果表明,流动注射分析法和高温氧化-化学发光检测法的测定范围更宽,精密度、准确度更好,3种样品的加标回收率达到96.2%~101%;高温氧化-化学发光检测法分析效率高、物料消耗少、节能环保,适用于一般海水样品的批量分析,且由于测定范围大,该法也适用于TN浓度较高的海水样品的批量分析,流动注射分析法因其较低的检出限更适用于TN浓度较低的海水样品的批量分析。     

Further studies using X-ray fluorescence to sample lead contaminated carpeted surfaces

The sampling of carpeted surfaces to test for lead contamination primarily focuses upon vacuum techniques. Vacuum sampling techniques, however, require time-consuming, expensive laboratory analysis of the dusts obtained and are unable to determine total lead load on the carpet. X-ray fluorescence (XRF) analysis is an on-site, inexpensive, non-destructive, quick technique for predicting metals levels in a variety of media, such as water, soil, filter paper and painted surfaces. A 1992 study of the feasibility of XRF to analyze for lead and soil loadings on carpeted surfaces indicated that XRF can detect lead at a low enough level to warrant further study. This paper expands this earlier study and developes lead and soil loading calibration curves for three different carpet types based upon XRF lead L-beta peak areas and XRF iron and barium K-alpha peak and background areas. Results indicate that variation in the data can be reduced through modifications of the XRF analysis technique, thus reducing the statistically determined detection level, and that carpet type does affect the calibration. Detection levels of approximately 70 mg/m² for lead and 5 g/m² for soil were obtained. Overall, good agreement was found between results of this study and the earlier one. XRF shows excellent potential for quantitative analysis of lead on carpeted surfaces.     

A field screening test for the assessment of concentrations and mobility of potentially toxic elements in soils: a case study on urban soils from Rome and Novi Sad

The increasing demand for environmental pollution control results in the development and use of new procedures for the determination of dangerous chemicals. Simple screening methods, which can be used directly in the field for a preliminary assessment of soil contamination, seem to be extremely advantageous. In our laboratory, we developed and optimized a rapid test for a preliminary evaluation of both the concentration and the mobility of some potentially toxic metals in soils. This screening test consists of a single extraction of the soil sample with a buffer solution, followed by the titration of the extracted solution with dithizone to determine the contents of bi-valent heavy metals (such as Pb, Cu, Zn, and Cd). This screening method was then directly applied in the field during the sampling campaign in the framework of an Italian–Serbian collaborative project, finalized in the study of metal availability in soils. The results obtained in the field with the rapid test were compared with those obtained in the laboratory following the conventional procedure commonly used to evaluate metal bioavailability (diethylenetriaminepentaacetic extraction). Moreover, selected samples were analyzed sequentially in the laboratory using the standardized BCR three-step sequential extraction procedure. The screening test gave results conceptually in good agreement with those obtained via the BCR procedure. These preliminary data show that the proposed screening test is a reliable method for the preliminary rapid evaluation of metal total concentrations and of potential metal mobility in soils, supporting sampling activities directly in the field.     

Comparison of collection efficiencies of sampling methods for removable beryllium surface contamination

The primary goal of this study is to compare wet versus dry sampling methods for three different media, (Whatman 41 filter papers, GhostWipes, and SKC Smear Tabs), These media were selected because they are the most commonly used means for the collection of beryllium from contaminated surfaces within the DOE Complex. A range of known concentrations of beryllium was introduced onto a smooth nonporous surface. All three types of media were tested for collection efficiency in both the wet and dry mode and analyzed by inductively-coupled plasma atomic emission spectrometry (ICP-AES).