Cytotoxicity of municipal solid waste incinerator ash wastes toward mammalian kidney cell lines

In this study, three municipal solid waste incinerator (MSWI) ash wastes-bottom ash, scrubber residue, and baghouse ash-were extracted using a toxicity characteristic leaching procedure (TCLP) extractant. These so-called final TCLP extracts were applied to African green monkey kidney cells (Vero), baby hamster kidney cells (BHK-21), and pig kidney cells (PK-15), multi-well absorption reader analysis was performed to test how the cytotoxicity of the incineration ashes would affect the digestive systems of animals. Ion-coupled plasma analyses indicated that the baghouse ash extract possessed the highest pH and heavy metal concentration, its cytotoxicity was also the highest. In contrast, the bottom ash and the scrubber residue exhibited very low cytotoxicities. The cytotoxicities of mixtures of baghouse ash and scrubber residue toward the three tested cell lines increased as the relative ratio of the baghouse ash increased, especially for the Vero cells. The slight cytotoxicity of the scrubber residue arose mainly from the presence of Cr species, whereas the high cytotoxicity of the baghouse ash resulted from its high content of heavy metals and alkali ions. In addition, it appears that the dissolved total organic carbon content of these ash wastes can reduce the cytotoxicity of ash wastes that collect in animal cells.     

Utilization of Dry Calcium Based Flue Gas Desulfurization Waste as a Hazardous Waste Fixation Agent

Several designated hazardous wastes (metal plating waste, oil sludge, heavy metal processing sludge) were studied relative to potential detoxification using dry calcium based FGD sludges. The FGD waste was generated from a pilot scale system which utilized slurried lime, a spray drier, and a bag filter. Following detailed physical and chemical identification of the raw FGD and hazardous wastes, various mixtures were prepared and cured. In all cases, even with the organic sludge, a rigid structural material evolved due to the pozzolanic reactions occurring from the wetted dry FGD waste. Structural characteristics, physical character, and chemical leaching effects were evaluated. The solids were leached via both EPA-RCRA and ASTM proposed leaching procedures. In all cases, the hazardous constituents were retained and not leached. Finally, the feasibility of using dry FGD wastes as fixating materials is discussed.     

Assessment of the mechanical stability and chemical leachability of immobilized electroplating waste

The effectiveness of cement based treatment technology, in immobilizing chromium laden electroplating sludge was assessed by conducting toxicity characteristic leaching procedure (TCLP). The mechanical stability of the blocks was tested by measuring the compressive strength. Other leaching tests such as NEN 7341 test, ANS 16.1 and multiple TCLP (MTCLP) test conducted on select solidified blocks showed that chromium was immobilized by the binder studied. A linear relationship was obtained between the cumulative fraction of chromium leached (CFL) and square root of time in the solidified samples proving that diffusion is the controlling mechanism for leaching of chromium. The leachability indices (LI) obtained for the solidified materials using cement and cement-fly ash system (EPC6, EPFC6A and EPFC6B) satisfy the guidance value as per US NRC, which clearly indicates that chromium is well retained within the solid matrix. Chromium concentrations in the TCLP leachates of the above mix ratios were well within the regulatory level of United States Environmental Protection Agency (USEPA). Molecular characterization of the solidified material was carried out using Fourier transformation infra red (FTIR) technique.     

Limitations of the toxicity characteristic leaching procedure for providing a conservative estimate of landfilled municipal solid waste incineration ash leaching

Limitations of the toxicity characteristic leaching procedure (TCLP) for simulating pollutant leaching from wastes disposed of in full-scale landfills are well understood in the waste management profession; the TCLP solution has a lower pH and greater organic acid content than typical landfill leachate. The TCLP serves its intended regulatory objective, however, as long as a conservative estimate of leaching is provided. Here, we examine TCLP’s ability to represent worst-case leaching conditions for monofilled municipal solid waste incineration (MSWI) ash. A critical examination of TCLP’s applicability to MSWI ash is especially relevant, as ash management at MSWI facilities often centers on passing TCLP, regardless of environmental risk posed by the ash or its recyclability. Multiple batch leaching tests were conducted on different MSWI ash streams: mixed ash, fly ash, and different size fractions of bottom ash. Batch-test results were compared with leachate simulating MSWI ash monofills. The TCLP did not consistently provide the most conservative estimate of leaching, supporting the need to consider alternative methodologies in future regulatory development.

Implications: This paper analyzes the existing hazardous waste regulatory testing requirement for municipal solid waste incinerator (MSWI) ash management to evaluate whether the TCLP serves its intended purpose in providing the most conservative estimate of landfilled MSWI ash. The results will serve as guidance and motivation for policy makers and the regulatory community to reevaluate the TCLP’s application for characterizing MSWI ash leaching in certain disposal scenarios and could promote consideration of alternative testing procedures based upon results of this study. This study serves to promote representative and accurate quantification of leaching risk from MSWI ash.     

Phosphorus release from ash, dried sludge and sludge residue from supercritical water oxidation by acid or base

Leaching of ash and dried sewage sludge were investigated and compared with the leaching results of sludge residue from supercritical water oxidation (SCWO). This article focuses on how the composition of ash and sludge residues influences the extraction of phosphate and heavy metals and if different treatment temperatures of the sludge effect the leachability. Results showed that acid leaching gave a higher release of phosphate than alkaline leaching for all ash and sludge residue samples. Also, alkaline leaching dissolved phosphate with a lower metal contamination than acid leaching. Furthermore, it was found that iron had a low release at both alkaline and acid leaching from ash and from SCWO residue. The difference in composition of ash and sludge residue samples had no significant influence on release of phosphate at high concentrations of acid. Phosphate release from ash, dried sludge at 300 degrees C and SCWO residue showed similar results at 1M acid leaching. However, it seems to be easier to release phosphate from the SCWO residue than from the ash at low acid concentrations. SCWO residue showed higher release than the other ashes at 0.5M HCl. Results for alkaline leaching showed higher release from ash at 1M NaOH than from SCWO residue or from dried sludge at 300 degrees C. The leaching of phosphate from dried sludge seems to be temperature dependent, as the dried sludge treated at higher temperature showed less release of phosphate. It was found that the pre-treatment of the ash may be important for better release of phosphate.     

含重金属水处理污泥的固化和浸出毒性研究

工业危险固体废物在进行安全填埋前需要进行固化稳定处理。针对电镀厂和皮革厂含重金属的水处理污泥 ,用不同比例的水泥、粉煤灰进行固化稳定处理。考虑酸雨环境 ,浸出实验采用TCLP标准。电镀厂污泥单独固化时 ,其浸出液中铜离子浓度由 78 0mg/L下降到 1 5mg/L ;镍离子浓度由 2 2 4 5mg/L下降到 2 2 2mg/L ,高于危险废物允许进入填埋区 15mg/L的控制限值。电镀厂污泥与皮革厂污泥混合后固化 ,浸出液毒性明显降低。铜离子的浸出浓度降低到1 98mg/L ,镍离子降低到 4 10mg/L ,总铬降低到 0 4 0mg/L ,各项指标均低于国家危险废物允许进入填埋区的控制限值 ,可安全填埋。     

A pilot and field investigation on mobility of PCDDs/PCDFs in landfill site with municipal solid waste incineration residue

A field investigation by boring was carried out in a landfill site primarily with municipal solid waste incineration residue. From the collected core samples, vertical profiles of homologous content of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/PCDFs) in the landfill layer were traced and the behavior of PCDDs/PCDFs was examined. In addition, a pilot-scale study was conducted on the PCDDs/PCDFs leached from incineration fly ash and the treated one using large landfill simulation columns (lysimeters) and the leaching behavior of PCDDs/PCDFs was examined. As a result, it was found that the coexistence of dissolved coloring constituents (DCCs), which might be composed of constituents like dissolved humic matters having strong affinity for hydrophobic organic pollutants, could enhance the leachability of PCDDs/PCDFs, thus contributing to the vertical movement and leaching behavior of PCDDs/PCDFs in the landfill layers of the incineration residue. Moreover, it is highly probable that DCCs derive from the unburned carbon in the bottom ash mixed and buried with the fly ash containing a high content of PCDDs/PCDFs.     

Stabilization of APC residues from waste incineration with ferrous sulfate on a semi-industrial scale

A stabilization method for air pollution control (APC) residues from municipal solid waste incineration (MSWI) involving mixing of the residue with water and FeSO4 has been demonstrated on a semi-industrial scale on three types of APC residues: a semidry (SD) APC residue, a fly ash (FA), and an FA mixed with sludge (FAS) from a wet flue gas cleaning system. The process was performed in batches of 165-175 kg residue. It generates a wastewater that is highly saline but has a low content of heavy metals such as Cd, Cr, and Pb. The stabilized and raw residues have been subject to a range of leaching tests: the batch leaching test, the pH-static leaching test, the availability test, and the column test. These tests showed that the stabilized residues have remarkably improved leaching properties, especially with respect to Pb but also with respect to Cd, Cu, and Zn. The release of Pb was reduced by a factor of 250-36,000.     

Fluidized-bed-combustion ash for the solidification and stabilization of a metal-hydroxide sludge

Fluidized-bed-combustion (FBC) ash is a by-product from a developing technology for coal-fired power plants that will economically reduce air emissions to meet requirements of the Clean Air Act. FBC ash has physical and chemical properties similar to Portland cement, but only has moderate success as a pozzolan in concrete applications due to low compressive strengths. However, FBC ash has proven effective for use as a binder for the solidification and stabilization (S/S) of metal-bearing sludges. Physical and chemical characterization procedures were used to analyze FBC ash and a metal-bearing sludge obtained from a hazardous waste treatment facility to develop 12 different S/S mix designs. The mix designs consist of four binder designs to evaluate sludge-to-binder ratios of approximately 0, 0.5, and 1. Portland cement is used as a control binder to compare unconfined compressive strengths and Toxicity Characteristic Leaching Procedure (TCLP) analyses from different ratios of the FBC ash streams: fly ash, char, and spent bed material (SBM). Compressive strengths ranging from 84 lbs per square inch (psi) to 298 psi were obtained from various mix designs containing different sludge-to-ash ratios cured for 28 days. All the mix designs passed the TCLP. Recoveries from leaching for each metal were less than 5% for most mix designs. Results of unconfined compressive strengths, TCLP, and percent recovery calculations indicate that the mix design containing approximately a 1:1 ratio of fly ash to char-and-sludge is the best mix design for the S/S of the metal-bearing sludge.     

Evaluation of the stability of arsenic immobilized by microbial sulfate reduction using TCLP extractions and long-term leaching techniques

An investigation was conducted to evaluate the stability or leachability of arsenic immobilized by microbial sulfate reduction. Anoxic solid-phase samples taken from a bioreactor previously used to treat metal and As contaminated water using sulfate reducing bacteria (SRB) were subjected to the toxicity characteristic leaching procedure (TCLP) and long-term column leaching tests. The results from TCLP experiments showed that the concentration of As leached from solid-phase sulfide material (SSM) samples after an 18 h extraction time was <300 microgl(-1), which is below the current maximum Australian TCLP leachate value for As, and thus would not be characterized as a hazardous waste. In terms of percent total As leached, this was equivalent to <8.5% for SSM samples initially containing 61.3 mgkg(-1) As. The levels of As extracted by the TCLP was found to be significantly lowered or underestimated in the presence of dissolved oxygen, with As concentrations increasing with decreasing headspace-to-leachant volume ratios. The concentration of As was also consistently higher in nitrogen purged extractions compared to those performed in air. This was attributed to the dissolution of Fe-sulfide precipitates and subsequent oxidation of Fe(II) ions and precipitation of ferric(hydr)oxides, resulting in the adsorption of soluble As and corresponding decrease in As concentrations. According to the experimental data, it is recommended that TCLP tests for As leachability should be performed at least in zero-headspace vessels or preferably under nitrogen to minimize the oxidation of Fe(II) to ferric(hydr)oxides. In long-term leaching studies (approximately 68 days), it was found that the low solubility of the SSM ensured that rate of release of As was relatively slow, and the resulting leachate concentrations of As were below the current Australian guideline concentration for arsenic in drinking water.     

Stabilization of APC Residues from Waste Incineration with Ferrous Sulfate on a Semi-Industrial Scale

Abstract

A stabilization method for air pollution control (APC) residues from municipal solid waste incineration (MSWI) involving mixing of the residue with water and FeSO₄ has been demonstrated on a semi-industrial scale on three types of APC residues: a semidry (SD) APC residue, a fly ash (FA), and an FA mixed with sludge (FAS) from a wet flue gas cleaning system. The process was performed in batches of 165-175 kg residue. It generates a wastewater that is highly saline but has a low content of heavy metals such as Cd, Cr, and Pb. The stabilized and raw residues have been subject to a range of leaching tests: the batch leaching test, the pH-static leaching test, the availability test, and the column test. These tests showed that the stabilized residues have remarkably improved leaching properties, especially with respect to Pb but also with respect to Cd, Cu, and Zn. The release of Pb was reduced by a factor of 250-36,000.     

Characteristics of leachate from pyrolysis residue of sewage sludge

The pyrolysis residue (SP) of sewage sludge (SS) produced at 500 degrees C was subjected to batch and column leaching tests to investigate the release of its organic and inorganic constituents and metals. For comparison, incineration ash (SI) obtained from a SS incinerator was also tested. Pyrolysis and incineration reduced organic matter of SS from 0.78 kg kg(-1)-dry SS to 0.16 and 0.01 kg kg(-1)-dry SS, respectively. Heavy metals remained in SP without being volatilized, although Cd and Pb were transferred into the off-gas during incineration. In the batch leaching test with the leaching liquid-to-solid mass ratio (L/S)=10, the pH of the SS, SP, and SI filtrates was 6.3, 7.9, and 11.0, respectively. The total organic carbon concentrations were in the order SS (877 l mg l(-1))>SP (99 mg l(-1))>SI (26 mg l(-1)). The SP and SI filtrates met the landfill standard for the Cd and Pb concentrations (<0.3 mg l(-1)). In the column tests, although the SP contained more organic matter than that of SI, its carbon discharge into the leachate under aerobic conditions was similar to that of SI under anaerobic conditions. The leaching of heavy metals, such as Cd, Cr, Pb, and Zn, was also suppressed in SP during the active decomposition of organic matter. We demonstrated that pyrolysis reduces the potential release of pollutants from sewage sludge in landfill, making it a promising method of treating sewage sludge before landfilling.     

The leachability and chemical speciation of selected trace elements in fly ash from coal combustion and refuse incineration

A laboratory leaching test has been used to predict the potential mobility of As, Se, Pb and Cd in landfilled fly ash produced by coal combustion and refuse incineration. These waste residues also formed the basis of a speciation study in which the valency states of As and Se and the chemical forms of Pb and Cd have been determined. Selenium displayed the greatest leachability in each ash type, despite being present at relatively low concentrations in both materials. Substantial amounts of other trace elements were also leached, particularly Pb and Cd from refuse ash and As from coal ash. Chemical associations of Pb and Cd were examined by a sequential extraction procedure. In coal fly ash, both elements were mostly present in the residual fraction, while in refuse ash these elements were mainly associated with the exchangeable fraction. Water-soluble extracts of coal fly ash contained As exclusively as As(V); high background interference prevented the detection of water-soluble As in refuse ash. Selenium was present largely as Se(IV) in aqueous extracts of both ash types. The value of speciation techniques and leaching tests as predictors of environmental behaviour is discussed in conjunction with results of routine trace element determinations and plant uptake studies.     

Leaching behavior and chemical stability of copper butyl xanthate complex under acidic conditions

Although xanthate addition can be used for treating copper-containing wastewater, a better understanding of the leaching toxicity and the stability characteristics of the copper xanthate complexes formed is essential. This work was undertaken to evaluate the leaching behavior of copper xanthate complex precipitates by means of toxicity characteristics leaching procedure (TCLP) and semi-dynamic leaching test (SDLT) using 1 N acetic acid solution as the leachant. Also, the chemical stability of the copper xanthate complex during extraction has been examined with the studying of variation of chemical structure using UV-vis, Fourier transform infrared and X-ray photoelectron spectroscopies (XPS).Both TCLP and SDLT results showed that a negligible amount of copper ion was leached out from the copper xanthate complex precipitate, indicating that the complex exhibited a high degree of copper leaching stability under acidic conditions. Nevertheless, chemical structure of the copper xanthate complex precipitate varied during the leaching tests. XPS data suggested that the copper xanthate complex initially contained both cupric and cuprous xanthate, but the unstable cupric xanthate change to the cuprous form after acid extraction, indicating the cuprous xanthate to be the final stabilizing structure. Despite that, the changes of chemical structure did not induce the rapid leaching of copper from the copper xanthate complex.     

村镇小型生活垃圾热处理炉底渣的理化特性

小型垃圾热处理设备可实现就地处置,节约运输成本,目前在中国山区、丘陵地带的村镇得到广泛应用.为了解村镇小型生活垃圾热处理炉底渣的理化特性及其影响因素,对中国云南、贵州、安徽村镇实际运行的小型生活垃圾热处理设备产生的底渣进行取样,分析其热灼减率、物理组成、化学组成、晶相组成、重金属含量和浸出特性,探讨处理工艺、地域及季节...     

2种浸出方法对水泥熟料的适用性比较

采用2种不同类型的代表性浸出方法:TCLP和NEN7371对不同重金属含量及不同烧制条件下所得水泥熟料进行浸出实验.结果表明,NEN7371方法下各样品中所有受试重金属几乎均有检出,大部分重金属的浸出率均高于10%;重金属的浸出浓度与其在熟料样品中含量的趋势对应性较好;TCLP方法下各样品中的受试重金属均只有部分检出,且浸出率一般在0.5%左右,浸出浓度很低,仪器检测误差较大.说明在考察水泥熟料中重金属的浸出特性时,NEN7371方法的适用性相对更好.     

Screening of heavy metal containing waste types for use as raw material in Arctic clay-based bricks

In the vulnerable Arctic environment, the impact of especially hazardous wastes can have severe consequences and the reduction and safe handling of these waste types are therefore an important issue. In this study, two groups of heavy metal containing particulate waste materials, municipal solid waste incineration (MSWI) fly and bottom ashes and mine tailings (i.e., residues from the mineral resource industry) from Greenland were screened in order to determine their suitability as secondary resources in clay-based brick production. Small clay discs, containing 20 or 40% of the different particulate waste materials, were fired and material properties and heavy metal leaching tests were conducted before and after firing. Remediation techniques (washing in distilled water and electrodialytical treatment) applied to the fly ash reduced leaching before firing. The mine tailings and bottom ash brick discs obtained satisfactory densities (1669–2007 kg/m³) and open porosities (27.9–39.9%). In contrast, the fly ash brick discs had low densities (1313–1578 kg/m³) and high open porosities (42.1–51. %). However, leaching tests on crushed brick discs revealed that heavy metals generally became more available after firing for all the investigated materials and that further optimisation is therefore necessary prior to incorporation in bricks.     

油页岩循环流化床锅炉底渣和飞灰中重金属元素浸出毒性研究

为了研究我国桦甸油页岩65 t/h循环流化床锅炉的底渣和飞灰中重金属元素Cr、Cu、Pb和Zn的赋存状态及不同酸度条件下的浸出特性,分别进行了逐级提取实验和分批浸出的淋滤实验。逐级提取实验结果表明,这4种元素在底渣和飞灰中具有基本相当的赋存状态。硫化物结合态和稳定的残渣态是各元素的主要赋存状态,元素的潜在浸出能力大小表现为:PbCrCuZn,飞灰中各元素的潜在浸出能力大于底渣中的。浸出实验结果表明,元素的赋存状态决定了其浸提能力,浸提液的pH值对各元素浸出能力的影响不尽相同,各元素的浸出能力随浸提时间的延长都会趋于平衡,Cr和Pb的浸出浓度都高于地表水和饮用水的国家标准。     

Fractionation and mobility of metals in bauxite red mud

Red mud (RM) is a strongly alkaline residue generated in enormous amounts worldwide from bauxite refining using the Bayer chemical process. RM is composed mainly of Fe, Ti and Al oxides and hydroxides, but it also contains an array of trace metals and metalloids at different concentrations. The purpose of this paper is to assess the potential mobility of metals in RM, with special emphasis on pH effect. The ‘operational’ distribution and leachability of metals within/from RM was studied by applying a sequential extraction procedure (SEP) and several leaching tests (rapid titration, equilibration acidification, batch leaching with acetic acid and also the toxicity characteristics leaching procedure (TCLP) and the DIN 38414-S4 procedures, used as reference methods) carried out at different pH, solid/liquid ratio, extraction period and type of acid (HCl or acetic acid). Chemical analysis showed that, in addition to the major metals Fe, Al and Ti, RM contains several trace metals, some of them (Cr, Cu and Ni) in concentrations exceeding the regulatory limits. SEP showed that a majority of the metals in the RM (between the 32.2?±?8.5 for Cd and 95.3?±?0.4 % for Ni) were found in the residual fraction, suggesting that they are not readily mobile under normal environmental conditions. Leaching tests performed at different pH showed that a significant fraction of the metals is mobilised from RM only under very strong acid conditions (pH?<?2), whereas Al is released in considerable amounts at pH?<?5.3. Among the trace metals, Cr requires special attention because of its relative high concentration in RM and the higher concentrations of this metal mobilised at low pH. The leaching tests using acetic acid showed that the standard TCLP largely underestimates the release of trace metals from RM, and therefore it is not advisable to evaluate the actual potential leaching of trace metals from this residue.     

Effect of sludge-processing mode, soil texture and soil pH on metal mobility in undisturbed soil columns under accelerated loading

The effect of sludge processing (digested dewatered, pelletized, alkaline-stabilized, composted, and incinerated), soil type and initial soil pH on trace metal mobility was examined using undisturbed soil columns. Soils tested were Hudson silt loam (Glossaquic Hapludalf) and Arkport fine sandy loam (Lamellic Hapludalf), at initial pH levels of 5 and 7. Sludges were applied during four accelerated cropping cycles (215 tons/ha cumulative application for dewatered sludge; equivalent rates for other sludges), followed by four post-application cycles. Also examined (with no sludge applications) were Hudson soil columns from a field site that received a heavy loading of sludge in 1978. Romaine (Lactuca sativa) and oats (Avena sativa) were planted in alternate cycles, with oats later replaced by red clover (Trifolium pratense). Soil columns were watered with synthetic acid rainwater, and percolates were analyzed for trace metals (ICP spectroscopy), electrical conductivity and pH. Percolate metal concentrations varied with sludge and soil treatments. Composted sludge and ash had the lowest overall metal mobilities. Dewatered and pelletized sludge had notable leaching of Ni, Cd and Zn in Arkport soils, especially at low pH. Alkaline-stabilized sludge had the widest range of percolate metals (relatively insensitive to soils) including Cu, Ni, B and Mo. Old site column percolate concentrations showed good agreement with previous field data. Little leaching of P was observed in all cases. Cumulative percolate metal losses for all treatments were low relative to total applied metals. Leachate and soil pH were substantially depressed in dewatered and pelletized sludge soil columns and increased for alkaline-stabilized and ash treatments.