Leaching behaviour of bottom ash from RDF high-temperature gasification plants

This study investigated the physical properties, the chemical composition and the leaching behaviour of two bottom ash (BA) samples from two different refuse derived fuel high-temperature gasification plants, as a function of particle size. The X-ray diffraction patterns showed that the materials contained large amounts of glass. This aspect was also confirmed by the results of availability and ANC leaching tests. Chemical composition indicated that Fe, Mn, Cu and Cr were the most abundant metals, with a slight enrichment in the finest fractions.Suitability of samples for inert waste landfilling and reuse was evaluated through the leaching test EN 12457-2. In one sample the concentration of all metals was below the limit set by law, while limits were exceeded for Cu, Cr and Ni in the other sample, where the finest fraction showed to give the main contribution to leaching of Cu and Ni.Preliminary results of physical and geotechnical characterisation indicated the suitability of vitrified BA for reuse in the field of civil engineering. The possible application of a size separation pre-treatment in order to improve the chemical characteristics of the materials was also discussed.     

Thermodynamic and experimental studies on condensation behavior of low-boiling-point elements volatilized in the melting process

To study the volatilization and condensation behaviors of low-boiling-point elements in the waste melting process, experiments were conducted to collect the dust from a coke-type incineration residue melting furnace. Then, a comparison was made between the experimental results and the calculated values obtained from a thermodynamic equilibrium model in terms of the chemical composition of the dust. The composition of the dust collected from a cylindrical filter in the exhaust gas duct was determined by chemical methods, scanning electron microscopy/energy-dispersive X-ray spectroscopy, and X-ray analysis. As a result, the sampled dust was classified into two different types: fine particles mainly containing Na, K, Pb, and Zn collected from the side face of the cylindrical filter, and large particles containing Ca, Si, and Al collected from the bottom face of the cylindrical filter. From X-ray analysis of the sampled dust, NaCl, KCl, PbS, and ZnS were identified in the fine-particle dust, while CaO, SiO₂, Al₂O₃ were detected in the large-particle dust. From the results of the thermodynamic equilibrium calculation in the gas cooling process from 2000 to 600 K, it was found that Na, K, Pb, and Zn volatilized as metals in the melting furnace were condensed as alkali chlorides such as NaCl and KCl and heavy metal sulfides such as PbS and ZnS. These computational results were in good agreement with the X-ray diffraction results of the sampled dust at a gas temperature of 823 K for the formation of NaCl, KCl, PbS, and ZnS.     

Prevention of lead leaching from fly ashes by mechanochemical treatment

Fly ashes from a municipal solid waste incinerator were subjected to mechanochemical (MC) treatment in a planetary ball mill, and the treated fly ashes were cemented with a binder. The leachability of lead (Pb) from the treated fly ashes and from the cement product were investigated, and the speciation of lead in the treated and untreated ashes was determined by X-ray absorption fine structure (XAFS) analysis. MC treatment of the fly ashes and subsequent cementation prevented Pb leaching by 99.9%, whereas MC treatment alone prevented Pb leaching by 92.8%. Analysis of the X-ray absorption near-edge spectrum of the untreated fly ashes revealed that the predominant Pb species in the ashes was PbCl₂. In contrast, the counterpart in the treated fly ashes was Pb₃O₄ insoluble in water. The formation of a species of Pb with a lower solubility in water than that of PbCl₂ was confirmed by MC treatment of PbCl₂-spiked fly ashes for 48 h, indicating the reduction of PbCl₂ in the spiked fly ashes to Pb via Pb₃O₄ during MC treatment. Our results indicate that such reduction to an insoluble species prevented Pb from leaching and that MC treatment followed by cementation is a feasible method for the recycling of fly ashes.     

Understanding the chemical and mineralogical properties of the inorganic portion of MSWI bottom ash

This paper investigates the changes of mineralogical composition of bottom ash in the environment. The chemical and mineralogical bulk composition was determined by X-ray fluorescence (XRF) and X-ray powder diffraction (XRPD) Rietveld method. Single bottom ash particles were investigated by optical microscopy, scanning electron microscopy with quantitative energy-dispersive X-ray microanalysis (SEM/EDX) and electron probe micro analysis (EPMA). SEM/EDX and EPMA are valuable complement to bulk analysis and provide means for rapid and sensitive multi-elemental analysis of ash particles. The fresh bottom ash consists of amorphous (>30 wt.%) and major crystalline phases (>1 wt.%) such as silicates, oxides and carbonates. The mineral assemblage of the fresh bottom ash is clearly unstable and an aging process occurs by reaction towards an equilibrium mineral phase composition in the environmental conditions. The significant decrease of anhydrite and amorphous contents was observed in the aged bottom ash, leading to the formation of ettringite, hydrocalumite and rosenhahnite under atmospheric conditions. In the water-treated sample, the calcite contents increased significantly, but ettringite was altered by the dissolution and precipitation processes in part, to produce gypsum, while the remaining part reacted with chloride to form hydrocalumite. Gypsum and other Ca based minerals may take up substantial amounts of heavy metals and subsequently control leaching behaviour of bottom ash.     

Immobilization of MSWI fly ash through geopolymerization: Effects of water-wash

The present research explored the role played by water-wash on geopolymerization for the immobilization and solidification of municipal solid waste incineration (MSWI) fly ash. The water-wash pretreatment substantially promoted the early strength of geopolymer and resulted in a higher ultimate strength compared to the counterpart without water-wash.XRD pattern of water-washed fly ash (WFA) revealed that NaCl and KCl were nearly eliminated in the WFA. Aside from geopolymer, ettringite (Ca₆Al₂(SO₄)₃(OH)₁₂·26H₂O) was formed in MSWI fly ash-based geopolymer (Geo-FA). Meanwhile, calcium aluminate hydrate (Ca₂Al(OH)₇·3H₂O), not ettringite, appeared in geopolymer that was synthesized with water-washed fly ash (Geo-WFA). Leached Geo-WFA (Geo-WFA-L) did not exhibit any signs of deterioration, while there was visual cracking on the surface of leached Geo-FA (Geo-FA-L). The crack may be caused by the migration of K⁺, Na⁺, and Cl⁻ ions outside Geo-FA and the negative effect from crystallization of expansive compounds can not be excluded. Furthermore, transformation of calcium aluminate hydrate in Geo-WFA to ettringite in Geo-WFA-L allowed the reduction of the pore size of the specimen. IR spectrums suggested that Geo-WFA can supply more stable chemical encapsulation for heavy metals.Static monolithic leaching tests were conducted for geopolymers to estimate the immobilization efficiency. Heavy metal leaching was elucidated using the first-order reaction/diffusion model. Combined with the results from compressive strength and microstructure of samples, the effects of water-wash on immobilization were inferred in this study.     

Heavy metals removal/stabilization from municipal solid waste incineration fly ash: a review and recent trends

Waste treatment using thermal technologies, such as incineration, leads to the production of pollutants and wastes, including fly ash (FA). Fly ash contains heavy metals (HMs) and other contaminants and can potentially pose high risks to the environment and negatively impact health and safety. Consequently, stabilizing fly ash prior to either use or landfilling is crucial. The toxicity of fly ash through heavy metal leaching can be assessed using leaching tests. The leaching rates of heavy metals primarily depend on the surrounding conditions as well as fly ash properties and metal speciation. Physical separation, leaching or extraction, thermal treatment and solidification/chemical stabilization are proposed as suitable approaches for fly ash treatment. Economic considerations, environmental concerns, energy consumption and processing times can define the efficiency and selection of the treatment approach. This review considers the latest findings and compares the advantages and shortcomings of different fly ash treatment methods with the aim of highlighting the recent advances in the field. The review concludes that the simultaneous implementation of various methods can lead to highly efficient heavy metals removal/stabilization while simultaneously taking economic and environmental considerations into account.

     

Glass–ceramic from mixtures of bottom ash and fly ash

Along with the gradually increasing yield of the residues, appropriate management and treatment of the residues have become an urgent environmental protection problem. This work investigated the preparation of a glass–ceramic from a mixture of bottom ash and fly ash by petrurgic method. The nucleation and crystallization kinetics of the new glass–ceramic can be obtained by melting the mixture of 80% bottom ash and 20% fly ash at 950 °C, which was then cooled in the furnace for 1 h. Major minerals forming in the glass–ceramics mainly are gehlenite (Ca₂Al₂SiO₇) & akermanite (Ca₂MgSiO₇) and wollastonite (CaSiO₃). In addition, regarding chemical/mechanical properties, the chemical resistance showing durability, and the leaching concentration of heavy metals confirmed the possibility of engineering and construction applications of the most superior glass–ceramic product. Finally, petrurgic method of a mixture of bottom ash and fly ash at 950 °C represents a simple, inexpensive, and energy saving method compared with the conventional heat treatment.     

Evaluation of the use of a sequential extraction procedure for the characterization and treatment of metal containing solid waste

Metal containing wastes like MSWI fly ashes and blast furnace sludge form a major environmental problem as they are polluted with heavy metals. The ash has to be landfilled or can be used as a construction material, but a pretreatment is in general necessary. Washing of the ashes with water in order to dissolve soluble salts or extracting the heavy metals with chemicals are possibilities. Blast furnace sludge contains large quantities of iron and carbon and could be recycled in the blast furnace, if the zinc content were not that high. Using a hydrometallurgical process the zinc can be removed from the sludge particles. In order to evaluate such treatment methods knowledge of the leaching behaviour of the studied material is very important. One of the factors influencing the leaching behaviour is the composition and mineralogy of the solids. A sequential extraction procedure, whereby the material is sequentially leached with different leaching solutions, can be used as an aid to characterize the material and to determine which chemical conditions are needed to obtain a sufficient extraction efficiency. To verify the accuracy of the sequential extraction procedure, a method is tested on MSWI fly ash and evaluated by comparing the results with those of leaching experiments whereby the final pH of the leaching solutions is varied over a wide range. Based upon this evaluation some suggestions for the use of the sequential extraction procedure are made and an adapted procedure is suggested, and applied to a blast furnace sludge.     

Effect of unburned carbon on lead, zinc, and copper recovery from molten fly ash by chloride-induced volatilization

The present work focuses on investigation of the effective recovery of heavy metals from molten fly ash by applying chloride-induced volatilization. In particular, the effect of unburned carbon on the chloride-induced volatilization of lead, zinc, and copper from model and real molten fly ashes was investigated in the temperature range 873–1173 K under a N₂ atmosphere. As a result, almost 100% of lead and a significant proportion of zinc were volatilized from the real molten fly ash samples at 1173 K. In contrast, for the model fly ash, volatilization ratios of lead and zinc at 1173 K were only 85% and 25%, respectively. Further, the results of X-ray diffraction analysis suggested that PbO in molten fly ash was converted either to Pb₂OCl₂ or Pb by respective chlorination and reduction reactions. Meanwhile ZnO and CuO in the molten fly ash were reduced to Zn and Cu by reaction with unburned carbon. Subsequently, Pb, Zn, and Pb₂OCl₂ were volatilized, but Cu remained in the solid residue. Finally, the volatilization ratio of zinc increased with the addition of carbon, and more than 98% of zinc was volatilized at 1173 K from a fly ash with a carbon content of 20%.     

Some limitations of sluiced fly ash as a liming material for acidic soils

Innovative methods are currently being sought to safely utilize and reduce the amount of sluiced fly ash stored in on-site facilities at thermal electric power facilities in Ontario, Canada. The objective of this study was to investigate the possibility of utilizing sluiced fly ash as a liming material on acidic soils. A greenhouse experiment was established to examine the influence of the ash on soil pH values and the yield and chemical composition of corn, soybeans, wheat and alfalfa grown on amended soil.The sluiced ash had an initial pH value of 9.1 (1:1 H₂O) and contained an equivalent CaCO₃ content of 11.5% (±0.2%) based on total content of Ca and Mg in the ash. Fly ash was applied at rates of up to 167 tonnes ha⁻¹ to samples of the surface horizon (0–15 cm) of an acidic clay textured soil found local to the power plant. Application of fly ash increased soil pH values but a high concentration of boron in the added ash limited plant growth. Results indicated that the sluiced ash could be used as a liming material at application rates of up to 110 tonnes ha⁻¹, on acidic, clay textured soils provided boron tolerant crops such as alfalfa were grown. Further research is required to establish the potential for leaching of boron to ground water and to determine the potential for plant uptake of other trace elements such as As and Se.     

Thermodynamic analysis of the role of chlorine and sulfur environments during combustion and incineration processes

 In order to control the emission of trace metals from combustion and incineration systems, sorbents and filters are sometimes used. However, the effectiveness of these methods is greatly affected by the volatility of the metals and the way in which they speciate during combustion, and afterwards during condensation, and physical or chemical sorption. Although there has been a lot of research into the mechanisms by which trace metals speciate and subsequently appear in submicron particles, the details of these mechanisms are not yet thoroughly understood. In this study, a chemical equilibrium approach was used to qualitatively determine the speciation of lead, cadmium, and chromium in Cl and S environments. The reaction conditions of sorbents were also tested numerically in order to understand the reaction behavior of metals with sorbents. This article reports the influence of different concentrations of Cl and SO₂ on Pb, Cd, and Cr speciation, as representatives of other trace elements. The partitioning behavior of metals during combustion was also examined for Cl and S. The results obtained indicate that most metals exist in the vapor phase, even at low temperatures, when chlorine is present. However, the addition of SO₂ enhances the formation of the condensed phase, except at extremely high temperatures. This observation was not significant for Cd or Cr. The higher the concentration of Cl the higher the retention of trace metals in the vapor phase, even at low temperatures. Results from comparisons of the reactivities of mixed metals with Cl indicate that the presence of Fe limits the reactivity of most trace metals with Cl except at higher concentrations. In the presence of Fe, alkali metals are the first to react with Cl. If Fe is not present, most trace metals react with Cl, and the activity increases with higher concentrations. On the other hand, the partitioning characteristics of S show that its presence generally means that metals remain in the condensed phase. Sulfur is more reactive with alkali metals than with other trace metals. Received: June 6, 2001 / Accepted: April 30, 2002     

Strength, leachability and microstructure characterisation of Na2SiO3-activated ground granulated blast-furnace slag solidified MSWI fly ash.

The chemical composition and the leachability of heavy metals in municipal solid waste incinerator (MSWI) fly ash were measured and analysed. For the leachability of unstabilized MSWI fly ash it was found that the concentrations of Pb and Cr exceeded the leaching toxicity standard. Cementitious solidification of the MSWI fly ash by Na2SiO3-activated ground granulated blast-furnace slag (NS) was investigated. Results show that all solidified MSWI fly ash can meet the landfill standards after 28 days of curing. The heavy metals were immobilized within the hydration products such as C-S-H gel and ettringite through physical encapsulation, substitution, precipitation or adsorption mechanisms.     

Re-cycling of remediated soil - Evaluation of leaching tests as tools for characterization

In Sweden, leaching tests with deionized water (D.W.) are utilized in risk assessment of materials entering landfills, but implementation of these results to evaluate the risk of spreading of pollutants in the environment is difficult. One problem is that most leaching procedures only consider heavy metals release, whereas organic pollutants are left out. The aim of the present study was to assess the possible pollutant mitigation in four remediated soils, three with heavy metals and one with polycyclic aromatic hydrocarbons (PAH) contamination. The mitigation was evaluated by standardized batch and column leaching tests utilizing three different leaching solutions: D.W., a weak ionic solution (0.001 M CaCl₂) and an artificially made soil water (ASW). In general, batch leaching tests implied larger contaminant removal than column leaching test, possibly due to the more rough treatment of the soil particles, and guidelines would at times be exceeded by the batch leaching test but not by column leaching tests. Utilization of CaCl₂ was found to release less heavy metal than D.W., whereas the metals mobilized by ASW were removed from solution by the filtration of soil leachates. Low molecular weight PAH was most efficiently mobilized by CaCl₂, while D.W. worked better for high molecular weight PAH. Despite very low initial PAH-concentrations, tap- and groundwater criteria were exceeded by all leaching solutions.     

Sustainable alkali-activated binders with municipal solid waste incineration ashes as sand or fly ash replacement

The present study investigates the feasibility of using two types of municipality solid wastes incineration ashes, namely, fly ash and bottom ash in the production of sustainable alkali-activated binder. The ashes are collected from the incineration plant and characterized to determine their particle size distribution, specific gravity, chemical composition, and heavy metals content. The ashes are then used as either fly ash or sand replacement with five replacement ratios 0%, 5%, 10%, 15%, and 20% to produce the binder. The produced binder are characterized in terms of strength, workability, density, water absorption, thermal conductivity and stability, chemical composition, and heavy metals content. The results reflect the ability of producing sustainable alkali-activated binder with small dosage of MSWI ashes as either fly ash or sand replacement without negatively affecting its strength, workability, density, and water absorption. The ashes enhance the thermal insulation capability of the binder.

     

Determining distribution coefficients for low cost adsorbents

As with other construction materials, coal fly ash contains trace metals that can leach into the natural environment. As part of a broader effort to encourage appropriate coal combustion product use in infrastructure applications (e.g., road construction, stabilization, and structural fill), this study evaluated traditional and low‐cost adsorbent alternatives for their capacity to attenuate trace metals. Batch sorption tests were used as a preliminary screen for a wide variety of low cost (e.g., steel byproducts, rubber dust, and compost) and innovative materials (e.g., kudzu, biofilm, and pond weed) as well as conventional materials (activated carbon, alumina, and zeolites). The removal rates were demonstrated in this study by observing the calculated distribution coefficient (K_d) which were determined using a program called MATLAB. Limestone and steel byproducts were found to be particularly effective with large K_d values of 15,740, 1,520, and 540 L kg^?1 for cadmium, chromium, and selenium and, for ladle refractory and mill scale, K_d values of 3,910, 670, and 1,760 L kg^?1 were observed. Among the three metals tested for this study, it was observed that most low cost and innovative materials removed cadmium quite efficiently; however, the removal of selenium and chromium depended on the substrate and prevailing pH. In general, these results suggest that alternative materials may have relevance in niche applications where leaching is a concern that can be addressed through enhanced attenuation capacity via blending or layering of adsorbents.     

Stabilization of heavy metals in MSWI fly ash using silica fume

The objective of this work was to investigate the feasibility and effectiveness of silica fume on stabilizing heavy metals in municipal solid waste incineration (MSWI) fly ash. In addition to compressive strength measurements, hydrated pastes were characterized by X-ray diffraction (XRD), thermal-analyses (DTA/TG), and MAS NMR (²⁷Al and ²⁹Si) techniques. It was found that silica fume additions could effectively reduce the leaching of toxic heavy metals. At the addition of 20% silica fume, leaching concentrations for Cu, Pb and Zn of the hydrated paste cured for 7 days decreased from 0.32 mg/L to 0.05 mg/L, 40.99 mg/L to 4.40 mg/L, and 6.96 mg/L to 0.21 mg/L compared with the MSWI fly ash. After curing for 135 days, Cd and Pb in the leachates were not detected, while Cu and Zn concentrations decreased to 0.02 mg/L and 0.03 mg/L. The speciation of Pb and Cd by the modified version of the European Community Bureau of Reference (BCR) extractions showed that these metals converted into more stable state in hydrated pastes of MSWI fly ash in the presence of silica fume. Although exchangeable and weak-acid soluble fractions of Cu and Zn increased with hydration time, silica fume addition of 10% can satisfy the requirement of detoxification for heavy metals investigated in terms of the identification standard of hazardous waste of China.     

Environmental friendly leaching reagent for cobalt and lithium recovery from spent lithium-ion batteries

We investigated an environmentally friendly leaching process for the recovery of cobalt and lithium from the cathode active materials of spent lithium-ion batteries. The easily degradable organic acid DL-malic acid (C₄H₅O₆) was used as a leaching reagent. The structural, morphology of the cathode materials before and after leaching were characterized by X-ray diffraction (XRD) and scanning electronic microscopy (SEM). The amount of Co and Li present in the leachate was determined by atomic absorption spectrophotometry (AAS). Conditions for achieving a recovery of more than 90 wt.% Co and nearly 100 wt.% Li were determined experimentally by varying the concentrations of leachant, time and temperature of the reaction as well as the initial solid-to-liquid ratio. We found that hydrogen peroxide in a DL-malic acid solution is an effective reducing agent because it enhances the leaching efficiency. Leaching with 1.5 M DL-malic acid, 2.0 vol.% hydrogen peroxide and a S:L of 20 g L^?1 in a batch extractor results in a highly efficient recovery of the metals within 40 min at 90 °C.     

Heavy metal speciation in various types of fly ash from municipal solid waste incinerator

Fly ash (FA) from municipal solid waste incinerators has been known as hazardous waste, which is mostly because of the high content of heavy metal and dioxins. Besides the content, the form of the heavy metals in fly ash is also very important, because it is tightly related with the leaching behavior of fly ash in diverse circumstances. To evaluate the environment potential risk of fly ash, the Tessier chemical extraction method was adopted. In this study, four kinds of fly ash were examined, one sample from China (CFA) and the other three from Japan (RFA, CaFA and NaFA). Five metal elements were detected and they were Ni, Cr, Cd, Pb, and Cu. The result of total heavy metals’ concentration showed CFA has the lowest content. As to the Tessier chemical extraction experiments, the results show that Cd, Pb, and Cu have higher leaching risk in the environment than other heavy metals. The result of leaching test experiment showed that the more exchangeable speciation of Cd, Cr and Pb in FA, the more it could leach out in natural environment.     

Belgian MSWI fly ashes and APC residues: a characterisation study

Municipal Solid Waste Incineration (MSWI) produces different sorts of residues, bottom ash, fly ashes and Air Pollution Control (APC) residues. Generally, fly ashes and APC residues are mixed at the MSWI plant and manage as a sole residue. In this study, fly ashes and APC residues have been sampled separately at different Belgian MSWI plant and analysed by X-ray fluorescence in order to highlight the composition differences that may appear between the solids. Ca and Cl are found to be the major elements in most of the samples. Lithophilic elements, such as Al and Si, are richer in furnace and boiler ashes, as can be expected. Leaching tests also show differences between the residues; leachates from furnace and boiler ashes are alkaline while those from bag filter residues present a pH value of 6, which impacts the leaching of heavy metals (Pb and Zn). The results suggest that it could be advantageous to manage fly ashes and APC residues separately by adjusting the treatment to their specificities.     

Use of mix of clay/solid waste from steel works for civil construction materials.

The present study focuses on the use of solid waste generated by the steel works in Brazil for manufacturing clay-based structural products. The waste sample was characterized regarding chemical composition, X-ray diffraction, particle size, morphology, specific surface and plastic properties. The waste was added in gradual proportions to a kaolinitic clay from zero up to 3 wt.%. Ceramic bodies were formed by vacuum extrusion and fired at 950 degrees C. The physical-mechanical properties (linear shrinkage, water absorption, apparent density and flexural strength) of the resulting clay/solid waste mixtures were determined. In addition, leaching tests were performed according Brazilian Standards as well as a preliminary analysis of gases evolved during the thermal process. It was found that the solid waste is formed by irregular particles, ranging in size from 1 to 500 microm. The test results indicate that solid wastes generated by steel works can be used as filler in construction materials, thereby increasing reuse in an environmentally safe manner.