Environmentally friendly system for the degradation of multipesticide residues in aqueous media by the Fenton’s reaction

A Fenton oxidation system employing zero-valent iron (whose source was swarf, a residue of metallurgical industries, in powder form) and hydrogen peroxide for the treatment of an aqueous solution with six pesticides was developed, and the effect of the iron metal content, pH, and hydrogen peroxide concentration was evaluated. The characterization of the aqueous solution resulted in: pH 5.6, 105 mg L^?1 of dissolved organic carbon, and 44.6 NTU turbidity. In addition, the characterization of the swarf by FAAS and ICP-MS showed 98.43?±?7.40 % of zero-valent iron. The removal was strongly affected by the content of iron metal, pH, and hydrogen peroxide concentration. The best degradation conditions were 2.0 g swarf, pH 2.0, and 5 mmol L^?1 H₂O₂. At the end of the treatment, the pesticide degradation ranged from 60 to 100 %, leading to 55 % mineralization. Besides, all hydrogen peroxide was consumed and the determination of total dissolved iron resulted in 2 mg L^?1. Thus, the advantages of this system are rapid degradation (up to 20 min), high-degradation rates, simple handling, and low cost.

Heterogeneous Fenton degradation of bisphenol A catalyzed by efficient adsorptive Fe3O4/GO nanocomposites

A new method for the degradation of bisphenol A (BPA) in aqueous solution was developed. The oxidative degradation characteristics of BPA in a heterogeneous Fenton reaction catalyzed by Fe₃O₄/graphite oxide (GO) were studied. Transmission electron microscopic images showed that the Fe₃O₄ nanoparticles were evenly distributed and were ～6 nm in diameter. Experimental results suggested that BPA conversion was affected by several factors, such as the loading amount of Fe₃O₄/GO, pH, and initial H₂O₂ concentration. In the system with 1.0 g L^?1 of Fe₃O₄/GO and 20 mmol L^?1 of H₂O₂, almost 90 % of BPA (20 mg L^?1) was degraded within 6 h at pH 6.0. Based on the degradation products identified by GC–MS, the degradation pathways of BPA were proposed. In addition, the reused catalyst Fe₃O₄/GO still retained its catalytic activity after three cycles, indicating that Fe₃O₄/GO had good stability and reusability. These results demonstrated that the heterogeneous Fenton reaction catalyzed by Fe₃O₄/GO is a promising advanced oxidation technology for the treatment of wastewater containing BPA.     

Influence of operational key parameters on the photocatalytic decolorization of Rhodamine B dye using Fe2+/H2O2/Nb2O5/UV system

The present research deals with the development of a new heterogeneous photocatalysis and Fenton hybrid system for the removal of color from textile dyeing wastewater as Rhodamine B (RhB) solutions by using Fe²⁺/H₂O₂/Nb₂O₅ as a photocatalytic system. The application of this photocatalytic system for the decolorization of dye contaminants is not reported in the literature yet. Different parameters like dye concentration, Nb₂O₅/Fe²⁺ catalyst amount, pH, and H₂O₂ concentration have been studied. The optimum conditions for the decolorization of the dye were initial concentration of 10 mg L^?1 of dye, pH 4, and Nb₂O₅/Fe²⁺ catalyst concentration of 0.5 g L^?1/50 mg L^?1. The optimum value of H₂O₂ concentration for the conditions used in this study was 700 mg L^?1. Moreover, the efficiency of the Nb₂O₅/photo-Fenton hybrid process in comparison to photo-Fenton alone and a dark Fenton process as a control experiment to decolorize the RhB solution has been investigated. The combination of photo-Fenton and Nb₂O₅ catalysts has been proved to be the most effective for the treatment of such type of wastewaters. The results revealed that the RhB dye was decolorized in a higher percent (78 %) by the Nb₂O₅/photo-Fenton hybrid process (Fe²⁺/H₂O₂/Nb₂O₅/UV) than by the photo-Fenton process alone (37 %) and dark Fenton process (14 %) after 120 min of treatment. Moreover, the Nb₂O₅ catalyst as a heterogeneous part of the photocatalytic system was demonstrated to have good stability and reusability.     

Phosphorus removal in a sulfur–limestone autotrophic denitrification (SLAD) biofilter

The sulfur–limestone autotrophic denitrification (SLAD) biofilter was able to remove phosphorous from wastewater during autotrophic denitrification. Parameters influencing autotrophic denitrification in the SLAD biofilter, such as hydraulic retention time (HRT), influent nitrate (NO₃ ^?), and influent PO₄ ^3? concentrations, had significant effects on P removal. P removal was well correlated with total oxidized nitrogen (TON) removed in the SLAD biofilter; the more TON removed, the more efficient P removal was achieved. When treating the synthetic wastewater containing NO₃ ^?-N of 30 mg L^?1 and PO₄ ^3?-P of 15 mg L^?1, the SLAD biofilter removed phosphorus of 45 % when the HRT was 6 h, in addition with TN removal of nearly 100 %. The optimal phosphorus removal in the SLAD biofilter was around 60 %. For the synthetic wastewater containing a PO₄ ^3?-P concentration of 15 mg L^?1, the main mechanism of phosphorus removal was the formation of calcium phosphate precipitates.     

Evaluation of Acinetobacter sp. B9 for Cr (VI) resistance and detoxification with potential application in bioremediation of heavy-metals-rich industrial wastewater

Present work demonstrates Cr (VI) detoxification and resistance mechanism of a newly isolated strain (B9) of Acinetobacter sp. Bioremediation potential of the strain B9 is shown by simultaneous removal of major heavy metals including chromium from heavy-metals-rich metal finishing industrial wastewater. Strain B9 tolerate up to 350 mg L^?1 of Cr (VI) and also shows level of tolerance to Ni (II), Zn (II), Pb (II), and Cd (II). The strain was capable of reducing 67 % of initial 7.0 mg L^?1 of Cr (VI) within 24 h of incubation, while in presence of Cu ions 100 % removal of initial 7.0 and 10 mg L^?1 of Cr (VI) was observed with in 24 h. pH in the range of 6.0–8.0 and inoculum size of 2 % (v/v) were determined to be optimum for dichromate reduction. Fourier transform infrared spectroscopy and transmission electron microscopy studies suggested absorption or intracellular accumulation and that might be one of the major mechanisms behind the chromium resistance by strain B9. Scanning electron microscopy showed morphological changes in the strain due to chromium stress. Relevance of the strain for treatment of heavy-metals-rich industrial wastewater resulted in 93.7, 55.4, and 68.94 % removal of initial 30 mg L^?1 Cr (VI), 246 mg L^?1 total Cr, and 51 mg L^?1 Ni, respectively, after 144 h of treatment in a batch mode.     

Arsenic toxicity in garden cress (Lepidium sativum Linn.): significance of potassium nutrition

In a hydroponic culture, experiments were performed to study the influence of potassium (K) supplementation (0, 20, 40, 60, 80, and 100 mg L^?1) on the arsenic (As; 0, 8, and 10 mg L^?1)-accrued changes in growth traits (plant biomass, root–shoot length) and the contents of lepidine, As and K, in garden cress (Lepidium sativum Linn.) at 10 days after treatment. The changes in these traits were correlated with shoot proline content, protein profile, and the activities of antioxidant enzymes namely superoxide dismutase (SOD, EC 1.15.1.1), catalase (CAT, EC 1.11.1.6), glutathione reductase (GR, EC 1.8.1.7), and ascorbate peroxidase (APX, EC 1.11.1.11). In general, As-alone treatments significantly decreased the growth traits but lead to significant enhancements in shoot proline and enzyme activities. K-supplementation to As-treated L. sativum seedlings decreased shoot-As content, reduced As-induced decreases in growth traits but enhanced the content of shoot proline, and the activities of the studied enzymes maximally with K₁₀₀ + As₈ and As₁₀ mg L^?1. Both 8 and 10 mg L^?1 of As drastically downregulated the shoot proteins ranging from 43–65 kDa. With As₁₀ mg L^?1, there was a total depletion of protein bands below 23 kDa; however, K₈₀ mg L^?1 maximally recovered and upregulated the protein bands. Additionally, protein bands were downregulated (at par with As-alone treatment) above K₈₀ mg L^?1 level. Interestingly, As-stress increased lepidine content in a dose-dependent manner which was further augmented with the K-supplementation. It is suggested that K protects L. sativum against As-toxicity by decreasing its accumulation and strengthening antioxidant defense system and protein stability.     

Improving the Fenton process by visible LED irradiation

The effect of irradiation with visible light-emitting diode (LED) light on the efficiency of Fenton oxidation is investigated using phenol as the target compound (100 mg/L). The H₂O₂ dose and temperature are tested as operating variables with the aim of minimizing consumption of the reagents. At 50 °C, 10 mg/L Fe²⁺, and 60 % of the stoichiometric H₂O₂ amount, phenol was completely oxidized into CO₂, H₂O, and short chain organic acids, with oxalic acid completely degraded. Up to 95 % mineralization was achieved. This high efficiency can be attributed to the effect of LED radiation on the quinones/Fe²⁺/Fe³⁺/H₂O₂ cycle, which significantly increases the reaction rate, as well as on the photodecomposition of the iron complexes formed along the oxidation process, which also enhanced mineralization.     

Principal component analysis to assess the efficiency and mechanism for enhanced coagulation of natural algae-laden water using a novel dual coagulant system

A novel dual coagulant system of polyaluminum chloride sulfate (PACS) and polydiallyldimethylammonium chloride (PDADMAC) was used to treat natural algae-laden water from Meiliang Gulf, Lake Taihu. PACS (Al_n(OH)_mCl_3n-m-2k(SO₄)_k) has a mass ratio of 10 %, a SO₄ ^2?/Al₃ ⁺ mole ratio of 0.0664, and an OH/Al mole ratio of 2. The PDADMAC ([C₈H₁₆NCl]_m) has a MW which ranges from 5?×?10⁵ to 20?×?10⁵ Da. The variations of contaminants in water samples during treatments were estimated in the form of principal component analysis (PCA) factor scores and conventional variables (turbidity, DOC, etc.). Parallel factor analysis determined four chromophoric dissolved organic matters (CDOM) components, and PCA identified four integrated principle factors. PCA factor 1 had significant correlations with chlorophyll-a (r?=?0.718), protein-like CDOM C1 (0.689), and C2 (0.756). Factor 2 correlated with UV₂₅₄ (0.672), humic-like CDOM component C3 (0.716), and C4 (0.758). Factors 3 and 4 had correlations with NH₃-N (0.748) and T-P (0.769), respectively. The variations of PCA factors scores revealed that PACS contributed less aluminum dissolution than PAC to obtain equivalent removal efficiency of contaminants. This might be due to the high cationic charge and pre-hydrolyzation of PACS. Compared with PACS coagulation (20 mg L^?1), the removal of PCA factors 1, 2, and 4 increased 45, 33, and 12 %, respectively, in combined PACS–PDADMAC treatment (0.8 mg L^?1?+?20 mg L^?1). Since PAC contained more Al (0.053 g/1 g) than PACS (0.028 g/1 g), the results indicated that PACS contributed less Al dissolution into the water to obtain equivalent removal efficiency.     

Application of chemical oxidation to remediate HCH-contaminated soil under batch and flow through conditions

This is the first study describing the chemical oxidation of hexachlorocyclohexanes (HCHs) in contaminated soil under water saturated and unsaturated flow through conditions. Soil contaminated with β-HCH (45 mg kg^?1) and γ-HCH (lindane, 25 mg kg^?1) was sampled from former lindane waste storage site. Efficiency of following treatments was tested at circumneutral pH: H₂O₂ alone, H₂O₂/Fe^II, Na₂S₂O₈ alone, Na₂S₂O₈/Fe^II, and KMnO₄. Experimental conditions (oxidant dose, liquid/solid ratio, and soil granulometry) were first optimized in batch experiments. Obtained results revealed that increasing dose of H₂O₂ improved the oxidation efficiency while in Na₂S₂O₈ system, maximum HCHs were removed at 300 mM. However, oxidation efficiency was slightly improved by Fe^II-activation. Increasing the solid/liquid ratio decreased HCH removal in soil samples crushed to 500 μm while an opposite trend was observed for 2-mm samples. Dynamic column experiments showed that oxidation efficiency followed the order KMnO₄ > Na₂S₂O₈/Fe^II > Na₂S₂O₈ whatever the flow condition, whereas the removal extent declined at higher flow rate (e.g., ~50% by KMnO₄ at 0.5 mL/min as compared to ~30% at 2 mL/min). Both HCH removal and oxidant decomposition extents were found higher in saturated columns than the unsaturated ones. While no significant change in relative abundance of soil mineral constituents was observed before and after chemical oxidation, more than 60% of extractable organic matter was lost after chemical oxidation, thereby underscoring the non-selective behavior of chemical oxidation in soil. Due to the complexity of soil system, chemical oxidation has rarely been reported under flow through conditions, and therefore our findings will have promising implications in developing remediation techniques under dynamic conditions closer to field applications.     

Effect of deposit age on adsorption and desorption behaviors of ammonia nitrogen on municipal solid waste

Ammonia nitrogen pollution control is an urgent issue of landfill. This research aims to select an optimal refuse for ammonia nitrogen removal in landfill from the point of view of adsorption and desorption behavior. MSW (municipal solid waste) samples which deposit ages were in the range of 5 to 15 years (named as R₁₅, R₁₁, R₇, and R₅) were collected from real landfill site. The ammonia nitrogen adsorption behaviors of MSW including equilibrium time, adsorption isotherms, and desorption behaviors including equilibrium time were determined. Furthermore, the effects of pH, OM, Cu(II), Zn(II), and Pb(II) on adsorption and desorption behavior of ammonia nitrogen were conducted by orthogonal experiment. The equilibrium time of ammonia nitrogen adsorption by each tested MSW was very short, i.e., 20 min, whereas desorption process needed 24 h and the ammonia nitrogen released from refuses was much lesser than that adsorbed, i.e., accounted for 3.20 % (R₁₅), 14.32 % (R₁₁), 20.59 % (R₇), and 20.50 % (R₅) of each adsorption quantity, respectively. The maximum adsorption capacity estimated from Langmuir isotherm appeared in R₁₅-KCl, i.e., 25,000 mg kg^?1. The best condition for ammonia nitrogen removal from leachate was pH >7.5, OM 23.58 %, Cu(II) <5 mg L^?1, Zn(II) <10 mg L^?1, and Pb(II) <1 mg L^?1. Ammonia nitrogen in landfill leachate could be quickly and largely absorbed by MSW but slowly and infrequently released. The refuse deposited for 15 years could be a suitable material for ammonia nitrogen removal.     

Bioelectrochemical anaerobic sewage treatment technology for Arctic communities

This study describes a novel wastewater treatment technology suitable for small remote northern communities. The technology is based on an enhanced biodegradation of organic carbon through a combination of anaerobic methanogenic and microbial electrochemical (bioelectrochemical) degradation processes leading to biomethane production. The microbial electrochemical degradation is achieved in a membraneless flow-through bioanode–biocathode setup operating at an applied voltage below the water electrolysis threshold. Laboratory wastewater treatment tests conducted through a broad range of mesophilic and psychrophilic temperatures (5–23 °C) using synthetic wastewater showed a biochemical oxygen demand (BOD₅) removal efficiency of 90–97% and an effluent BOD₅ concentration as low as 7 mg L^?1. An electricity consumption of 0.6 kWh kg^?1 of chemical oxygen demand (COD) removed was observed. Low energy consumption coupled with enhanced methane production led to a net positive energy balance in the bioelectrochemical treatment system.     

Continuous flow photo-Fenton treatment of ciprofloxacin in aqueous solutions using homogeneous and magnetically recoverable catalysts

The degradation of ciprofloxacin was studied in aqueous solutions by using a continuous flow homogeneous photo-Fenton process under simulated solar light. The effect of different operating conditions on the degradation of ciprofloxacin was investigated by changing the hydrogen peroxide (0–2.50 mM) and iron(II) sulphate (0–10 mg Fe L^?1) concentrations, as well as the pH (2.8–10), irradiance (0–750 W m^?2) and residence time (0.13–3.4 min) of the process. As expected, the highest catalytic activity in steady state conditions was achieved at acidic pH (2.8), namely 85 % of ciprofloxacin conversion, when maintaining the other variables constant (i.e. 2.0 mg L^?1 of iron(II), 2.50 mM of hydrogen peroxide, 1.8 min of residence time and 500 W m^?2 of irradiance). Additionally, magnetite magnetic nanoparticles (ca. 20 nm of average particle size) were synthesized, characterized and tested as a possible catalyst for this reaction. In this case, the highest catalytic activity was achieved at natural pH, namely a 55 % average conversion of ciprofloxacin in 1.8 min of residence time and under 500 W m^?2. Some of the photocatalytic activity was attributed to Fe²⁺ leaching from the magnetic nanoparticles to the solution.     

Photolysis of atrazine in aqueous solution: role of process variables and reactive oxygen species

Photochemical advanced oxidation processes have been considered for the treatment of water and wastewater containing the herbicide atrazine (ATZ), a possible human carcinogen and endocrine disruptor. In this study, we investigated the effects of the photon emission rate and initial concentration on ATZ photolysis at 254 nm, an issue not usually detailed in literature. Moreover, the role of reactive oxygen species (ROS) is discussed. Photon emission rates in the range 0.87?×?10¹⁸–3.6?×?10¹⁸ photons L^?1 s^?1 and [ATZ]₀?=?5 and 20 mg L^?1 were used. The results showed more than 65 % of ATZ removal after 30 min. ATZ photolysis followed apparent first-order kinetics with k values and percent removals decreasing with increasing herbicide initial concentration. A fivefold linear increase in specific degradation rate constants with photon emission rate was observed. Also, regardless the presence of persistent degradation products, toxicity was efficiently removed after 60-min exposure to UV radiation. Experiments confirmed a noticeable contribution of singlet oxygen and radical species to atrazine degradation during photolysis. These results may help understand the behavior of atrazine in different UV-driven photochemical degradation treatment processes.     

Soil pH and Anion Abundance Affects on Copper Adsorption

Abstract

Copper (Cu) input to agricultural soils results from Cu containing pesticides and/or that in soil amendments, such as manure or sewage sludge. Soil and soil solution properties influence the adsorption and desorption of Cu by the soil, which in turn determines its plant availability and/or phytotoxicities. Effects of different anion enrichment in the equilibrium solution on Cu adsorption by different soils (pH range of 6.2–9.9) were investigated in this study over a range of Cu concentrations. With Cu concentrations in the range of 0–100 mg L^?1 in the equilibration solution, 95–99% of applied Cu was adsorbed by all three soils. The adsorption of Cu was similar regardless of using either 0.01 M CaCl₂ or Ca(NO₃)₂ as the equilibration solution. When the Cu concentration in the equilibration solution was further increased in the range of 500–2000 mg L^?1, the adsorption of Cu decreased from 60 to 24% of applied Cu in two soils with pH 6.2–7.9. In a high pH soil (pH = 9.9), the Cu adsorption decreased from 77 to 34%. Addition of incinerated sewage sludge (ISS) to a Palouse silt loam soil (pH = 6.2) increased the Cu adsorption as compared to that by unamended soil. This was, in part, due to an increase in the soil suspension pH with ISS amendment.     

Synthetic olive mill wastewater treatment by Fenton’s process in batch and continuous reactors operation

Degradation of total phenol (TPh) and organic matter, (expressed as total organic carbon TOC), of a simulated olive mill wastewater was evaluated by the Fenton oxidation process under batch and continuous mode conditions. A mixture of six phenolic acids usually found in these agro-industrial wastewaters was used for this purpose. The study focused on the optimization of key operational parameters of the Fenton process in a batch reactor, namely Fe²⁺ dosage, hydrogen peroxide concentration, pH, and reaction temperature. On the assessment of the process efficiency, > 99% of TPh and > 56% of TOC removal were attained when [Fe²⁺] = 100 ppm, [H₂O₂] = 2.0 g/L, T = 30 °C, and initial pH = 5.0, after 300 min of reaction. Under those operational conditions, experiments on a continuous stirred-tank reactor (CSTR) were performed for different space-time values (τ). TOC and TPh removals of 47.5 and 96.9%, respectively, were reached at steady-state (for τ = 120 min). High removal of COD (> 75%) and BOD₅ (> 70%) was achieved for both batch and CSTR optimum conditions; analysis of the BOD₅/COD ratio also revealed an increase in the effluent’s biodegradability. Despite the high removal of lumped parameters, the treated effluent did not met the Portuguese legal limits for direct discharge of wastewaters into water bodies, which indicates that coupled chemical-biological process may be the best solution for real olive mill wastewater treatment.     

Solar CPC pilot plant photocatalytic degradation of bisphenol A in waters and wastewaters using suspended and supported-TiO2. Influence of photogenerated species

Photocatalytic degradation of bisphenol A (BPA) in waters and wastewaters in the presence of titanium dioxide (TiO₂) was performed under different conditions. Suspensions of the TiO₂ were used to compare the degradation efficiency of BPA (20 mg L^?1) in batch and compound parabolic collector (CPC) reactors. A TiO₂ catalyst supported on glass spheres was prepared (sol–gel method) and used in a CPC solar pilot plant for the photodegradation of BPA (100 μg L^?1). The influence of OH·, O₂ ^·?, and h ⁺ on the BPA degradation were evaluated. The radicals OH· and O₂ ^·? were proved to be the main species involved on BPA photodegradation. Total organic carbon (TOC) and carboxylic acids were determined to evaluate the BPA mineralization during the photodegradation process. Some toxicological effects of BPA and its photoproducts on Eisenia andrei earthworms were evaluated. The results show that the optimal concentration of suspended TiO₂ to degrade BPA in batch or CPC reactors was 0.1 g L^?1. According to biological tests, the BPA LC₅₀ in 24 h for E. andrei was of 1.7?×?10^?2 mg cm^?2. The photocatalytic degradation of BPA mediated by TiO₂ supported on glass spheres suffered strong influence of the water matrix. On real municipal wastewater treatment plant (MWWTP) secondary effluent, 30 % of BPA remains in solution; nevertheless, the method has the enormous advantage since it eliminates the need of catalyst removal step, reducing the cost of treatment.     

Influence of exogenous urea on photosynthetic pigments, 14CO2 uptake, and urease activity in Elodea densa—environmental implications

This paper analyzes the effect of exogenous urea in increased concentration gradient (0, 100, 500 and 1,000 mg L^?1) on photosynthetic pigments (measured spectrophotometrically), uptake of ¹⁴CO₂ (using radioisotope), and urease activity (by measuring ammonia with Nessler’s reagent) in leaves of Elodea densa Planch. We have observed that low concentration of urea (100 mg L^?1) stimulates the accumulation of photosynthetic pigments and intensifies photosynthesis in E. densa, whereas high concentration (1,000 mg L^?1) suppresses these processes. Urease activity increased by approximately 2.7 and 8 fold when exogenous urea concentrations were 100 and 500 mg L^?1, respectively. However, exogenous urea in high concentration (1,000 mg L^?1) decreased urease activity by 1.5 fold compared to the control. The necessity of mitigating urea and other nitrogen-containing compounds (NH₃ from urea) in water bodies has been discussed with emphasis on the potential for phytoremediation of urea using common water weed viz. E. densa.     

Strategies to evaluate biodegradability: application to chlorinated herbicides

The biodegradability of nitrochlorinated (diuron and atrazine) and chlorophenoxy herbicides (2,4-D and MCPA) has been studied through several bioassays using different testing times and biomass/substrate ratios. A fast biodegradability test using unacclimated activated sludge yielded no biodegradation of the herbicides in 24 h. The inherent biodegradability test gave degradation percentages of around 20–30 % for the nitrochlorinated herbicides and almost complete removal of the chlorophenoxy compounds. Long-term biodegradability assays were performed using sequencing batch reactor (SBR) and sequencing batch membrane bioreactor (SB-MBR). Fixed concentrations of each herbicide below the corresponding EC₅₀ value for activated sludge were used (30 mg L^?1 for diuron and atrazine and 50 mg L^?1 for 2,4-D and MCPA). No signs of herbicide degradation appeared before 35 days in the case of diuron and atrazine and 21 days for 2,4-D, whereas MCPA was partially degraded since the early stages. Around 25–36 % degradation of the nitrochlorinated herbicides and 53–77 % of the chlorophenoxy ones was achieved after 180 and 135 days, respectively, in SBR, whereas complete disappearance of 2,4-D was reached after 80 days in SB-MBR.     

Utilization of water chestnut for reclamation of water environment and control of cyanobacterial blooms

Overgrowth of water chestnut (Trapa spp.) is a regional problem throughout Asia and North America because of waterway blockage and water fouling upon decomposition. In the present study, we investigated the potential of water chestnut to control cyanobacterial blooms, via a high content of phenolic compounds. In addition, we assessed the impact of biomass harvesting and crude extract application on nutrient balance. We showed that the floating parts of water chestnut contained high concentrations of total phenolics (89.2 mg g^?1 dry weight) and exhibited strong antioxidant activity (1.31 mmol g^?1 dry weight). Methanol-extracted phenolics inhibited growth of Microcystis aeruginosa; the half maximal effective concentration (EC₅₀) of the extracted phenolics was 5.8 mg L^?1, which was obtained from only 103 mg L^?1 of dry biomass (the floating and submerged parts). However, the crude extracts also added important quantities of nitrogen, phosphorus, and potassium (1.49, 1.05, and 16.3 mg g^?1, respectively; extracted dry biomass weight basis); therefore, in practice, nutrient removal before and/or after the extraction is essential. On the other hand, biomass harvesting enables recovery of nitrogen, phosphorus, and potassium from the water environment (23.1, 2.9, and 18.7 mg g^?1, respectively; dry biomass weight basis). Our findings indicate that water chestnut contains high concentrations of phenolics and exhibits strong antioxidant activity. Utilization of these resources, including nutrients, will contribute to reclamation of the water environment, and also to disposal of wet biomass.     

Phytoaccumulation potentials of two biotechnologically propagated ecotypes of Arundo donax in copper-contaminated synthetic wastewater

An in vitro experiment was carried out to evaluate the phytoremediation potentials of two somatic embryo-derived ecotypes of Arundo donax—BL (American ecotype) and 20SZ (Hungarian ecotype)—of copper from synthetic wastewater. The two ecotypes were grown under sterile conditions in tubes containing a nutrient solution supplied with increasing doses of Cu (0, 1, 2, 3, 5, 10, and 26.8 mg L^?1) for 6 weeks. The translocation and bioaccumulation factors and removal rate were estimated. In general, increasing Cu concentration in nutrient solution slightly decreased root, stem and leaf biomass without toxicity symptoms up to 26.8 mg L^?1. Moreover, both ecotypes showed high Cu removal efficiency from aqueous solution. However, Cu removal rate ranged between 96.6 to 98.8 % for BL ecotype and 97 to 100 % for 20SZ ecotype. Data illustrated that both BL and 20SZ ecotypes may be employed to treat Cu-contaminated water bodies up to 26.8 mg L^?1.