Photocatalytic reduction of carbon dioxide over Cu/TiO<Subscript>2</Subscript> photocatalysts

The photocatalytic reduction of CO₂ with H₂O was investigated using Cu/TiO₂ photocatalysts in aqueous solution. For this purpose, Cu/TiO₂ photocatalysts (with 0.2, 0.9, 2, 4, and 6 wt.% of Cu) have been synthesized via sol-gel method. The photocatalysts were extensively characterized by means of inductively coupled plasma optical emission spectrometry (ICP-OES), N₂ physisorption (BET), XRD, UV-vis DRS, FT-IR, Raman spectroscopy, TEM-EDX, and photoelectrochemical measurements. The as-prepared photocatalysts contain anatase as a major crystalline phase with a crystallite size around 13 nm. By increasing the amount of Cu, specific surface area and band gap energy decreased in addition to the formation of large agglomeration of CuO. Results revealed that the photocatalytic reduction of CO₂ decreased in the presence of Cu/TiO₂ in comparison to pure TiO₂, which might be associated to the formation of CuO phase acting as a recombination center of generated electron-hole pair. Decreasing of photoactivity can also be connected with a very low position of conduction band of photocatalysts with high Cu content, which makes H₂ production necessary for CO₂ reduction more difficult.     

Solar-driven photocatalytic treatment of diclofenac using immobilized TiO<Subscript>2</Subscript>-based zeolite composites

The study is aimed at evaluating the potential of immobilized TiO₂-based zeolite composite for solar-driven photocatalytic water treatment. In that purpose, TiO₂-iron-exchanged zeolite (FeZ) composite was prepared using commercial Aeroxide TiO₂ P25 and iron-exchanged zeolite of ZSM5 type, FeZ. The activity of TiO₂-FeZ, immobilized on glass support, was evaluated under solar irradiation for removal of diclofenac (DCF) in water. TiO₂-FeZ immobilized in a form of thin film was characterized for its morphology, structure, and composition using scanning electron microscopy/energy-dispersive x-ray spectroscopy (SEM/EDX). Diffuse reflectance spectroscopy (DRS) was used to determine potential changes in band gaps of prepared TiO₂-FeZ in comparison to pure TiO₂. The influence of pH, concentration of hydrogen peroxide, FeZ wt% within the composite, and photocatalyst dosage on DCF removal and conversion efficiency by solar/TiO₂-FeZ/H₂O₂ process was investigated. TiO₂-FeZ demonstrated higher photocatalytic activity than pure TiO₂ under solar irradiation in acidic conditions and presence of H₂O₂.     

Photocatalytic decomposition of N<Subscript>2</Subscript>O over g-C<Subscript>3</Subscript>N<Subscript>4</Subscript>/WO<Subscript>3</Subscript> photocatalysts

Although the nitrous oxide belongs among three of the most contributing greenhouse gases to global warming, it is quite neglected by photocatalytic society. The g-C₃N₄ and WO₃ composites were therefore tested for the photocatalytic decomposition of N₂O for the first time. The pure photocatalysts were prepared by simple calcination of precursors, and the composites were prepared by mixing of suspension of pure components in water followed by calcination. The structural (X-ray diffraction, X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy), textural (N₂ physisorption), and optical properties (diffuse reflectance spectroscopy, photoluminescence spectroscopy, photoelectrochemical measurements) of all composites were correlated with photocatalytic activity. The experimental results and results from characterization techniques confirmed creation of Z-scheme in the WO₃/g-C₃N₄ composites, which was confirmed by hydroxyl radicals’ trapping measurements. The photocatalytic decomposition of N₂O was carried out in the presence of UVA light (peak intensity at 365 nm) and the 1:2 WO₃/g-C₃N₄ composite was the most active one, but the photocatalytic activity was just negligibly higher than that of pure WO₃. This is caused by relatively weak interaction between WO₃ and g-C₃N₄ which was revealed from XPS.     

UV–visible light-activated Ag-decorated,monodisperse TiO2 aggregates for treatment of the pharmaceutical oxytetracycline

Noble metal Ag-decorated, monodisperse TiO₂ aggregates were successfully synthesized by an ionic strength-assisted, simple sol–gel method and were used for the photocatalytic degradation of the antibiotic oxytetracycline (OTC) under both UV and visible light (UV–visible light) irradiation. The synthesized samples were characterized by X-ray diffraction analysis (XRD); UV–vis diffuse reflectance spectroscopy; environmental scanning electron microscopy (ESEM); transmission electron microscopy (TEM); high-resolution TEM (HR-TEM); micro-Raman, energy-dispersive X-ray spectroscopy (EDS); and inductively coupled plasma optical emission spectrometry (ICP-OES). The results showed that the uniformity of TiO₂ aggregates was finely tuned by the sol–gel method, and Ag was well decorated on the monodisperse TiO₂ aggregates. The absorption of the samples in the visible light region increased with increasing Ag loading that was proportional to the amount of Ag precursor added in the solution over the tested concentration range. The Brunauer, Emmett, and Teller (The BET) surface area slightly decreased with increasing Ag loading on the TiO₂ aggregates. Ag-decorated TiO₂ samples demonstrated enhanced photocatalytic activity for the degradation of OTC under UV–visible light illumination compared to that of pure TiO₂. The sample containing 1.9 wt% Ag showed the highest photocatalytic activity for the degradation of OTC under both UV–visible light and visible light illumination. During the experiments, the detected Ag leaching for the best TiO₂-Ag photocatalyst was much lower than the National Secondary Drinking Water Regulation for Ag limit (0.1 mg L^?1) issued by the US Environmental Protection Agency.     

Use of carbon-based composites to enhance performance of TiO<Subscript>2</Subscript> for the simultaneous removal of nitrates and organics from aqueous environments

The simultaneous photocatalytic removal of nitrate from aqueous environment in presence of organic hole scavenger using TiO₂ has long been explored. However, the use of unmodified TiO₂ in such reaction resulted in non-performance or release of significant amount of undesirable reaction products in the process, a problem that triggered surface modification of TiO₂ for enhanced photocatalytic performance. Previous studies focused on decreasing rate of charge carrier recombination and absorption of light in the visible region. Yet, increasing active sites and adsorption capacity by combining TiO₂ with a high surface area adsorbent such as activated carbon (AC) remains unexploited. This study reports the potential of such modification in simultaneous removal of nitrates and oxalic acid in aqueous environment. The adsorptive behaviour of nitrate and oxalic acid on TiO₂ and TiO₂/AC composites were studied. The Langmuir adsorption coefficient for nitrate was four times greater than that of oxalic acid. However, the amount of oxalic acid adsorbed was about 10 times greater than the amount of nitrate taken up. Despite this advantage, the materials did not appear to produce more active photocatalysts for the simultaneous degradation of nitrate and oxalic acid. The photocatalytic activity of TiO₂ and its carbon-based composites was improved by combination with Cu₂O particles. Consequently, 2.5 Cu₂O/TiO₂ exhibited the maximum photocatalytic performance with 57.6 and 99.8% removal of nitrate and oxalic acid, respectively, while selectivity stood at 45.7, 12.4 and 41.9% for NH₄⁺, NO₂^? and N₂, respectively. For the carbon based, 2.5 Cu₂O/TiO₂-20AC showed removal of 12.7% nitrate and 80.3% oxalic acid and achieved 21.6, 0 and 78.4% selectivity for NH₄⁺, NO₂^? and N₂, respectively. Using the optimal AC loading (20 wt%) resulted in significant decrease in the selectivity for NH₄⁺ with no formation of NO₂^?, which unveils that selectivity for N₂ and low/no selectivity for undesirable products can be manipulated by controlling the rate of consumption of oxalic acid. In contract, no nitrate reduction was observed with Cu₂O promoted TiO₂-T and its TiO₂-(T)-20AC, which may be connected to amorphous nature of TiO₂-T and perhaps served as charge carrier trapping sites that impeded activity.     

Enhanced photocatalytic activity using GO/TiO<Subscript>2</Subscript> catalyst for the removal of DCA solutions

This work aimed to optimize high-performance photocatalysts based on graphene oxide/titanium dioxide (GO/TiO₂) nanocomposites for the effective degradation of aqueous pollutants. The catalytic activity was tested against the degradation of dichloroacetic acid (DCA), a by-product of disinfection processes that is present in many industrial wastewaters and effluents. GO/TiO₂ photocatalysts were prepared using three different methods, hydrothermal, solvothermal, and mechanical, and varying the GO/TiO₂ ratio in the range of 1 to 10%. Several techniques were applied to characterize the catalysts, and better coupling of GO and TiO₂ was observed in the thermally synthesized composites. Although the results obtained for DCA degradation showed a coupled influence of the composite preparation method and its composition, promising results were obtained with the photocatalysts compared to the limited activity of conventional TiO₂. In the best case, corresponding to the composite synthesized via hydrothermal method with 5% of GO/TiO₂ weight ratio, an enhancement of 2.5 times of the photocatalytic degradation yield of DCA was obtained compared to bare TiO₂, thus opening more efficient ways to promote the application of photocatalytic remediation technologies.     

Relationship between Pd oxidation states on TiO2 and the photocatalytic oxidation behaviors of nitric oxide

This study has been undertaken to investigate the relationship between Pd oxidation states on TiO₂ photocatalysts and their photocatalytic oxidation behaviors of NO. Three types of Pd-modified TiO₂ with different Pd oxidation states were prepared by wet impregnation method, neutralization method and photodeposition method, respectively. And these Pd-modified photocatalysts were characterized by X-ray diffraction analysis, X-ray photoelectron spectrum analysis (XPS), UV–Vis diffuse reflectance spectra and temperature programmed desorption (TPD). It was found from XPS results that the dominant oxidation states of Pd on these Pd-modified TiO₂ catalysts were Pd²⁺, PdO, and Pd⁰, respectively. NO-TPD results showed that the NO adsorption capacity was improved greatly by the modification of Pd²⁺ ions. The activity tests showed that Pd-modified TiO₂ by a wet impregnation method increased photocatalytic activity compared to pure TiO₂ (Degussa P25). It was concluded that Pd²⁺ ions on as-prepared TiO₂ catalysts provided key contributions to the improvement of photocatalytic activity. However, Pd⁰ and PdO deposits on TiO₂ almost had no positive effect on NO oxidation. The mechanism of photocatalytic oxidation of NO in gas phase over Pd-modified TiO₂ was also proposed.     

Photocatalytic degradation of gaseous toluene over Ag-doping TiO₂ nanotube powder prepared by anodization coupled with impregnation method

In this work, Ag-doping TiO₂ nanotubes were prepared and employed as the photocatalyst for the degradation of toluene. The TiO₂ nanotube powder was produced by the rapid-breakdown potentiostatic anodization of Ti foil in chloride-containing electrolytes, and then doped with Ag through an incipient wetness impregnation method. The samples were characterized by scanning electron microscope, high-resolution transmission electron microscopy, X-ray diffraction, surface photovoltage measurements, X-ray photoelectron spectroscopy and N₂ adsorption. The nanotubular TiO₂ photocatalysts showed an outer diameter of approximately 40 nm, fine mesoporous structure and high specific surface area. The photocatalytic activity of Ag-doping TiO₂ nanotube powder was evaluated through photooxidation of gaseous toluene. The results indicated that the degradation efficiency of toluene could get 98% after 4 h reaction using the Ag-doping TiO₂ nanotubes as the photocatalyst under UV light illumination, which was higher than that of the pure TiO₂ nanotubes, Ag-doping P25 or P25. Benzaldehyde species could be observed during the photocatalytic oxidation monitored by in situ FTIR, and the formed benzaldehyde intermediate during reaction would be partially oxidized into CO₂ and H₂O.     

铂铈共掺杂纳米TiO2的制备、表征及光催化性能

以钛酸四丁酯为前驱体,过氧化氢为氧化剂,采用简单易行的低温氧化法制备出晶粒尺寸较小(平均尺寸25 nm)的二氧化钛纳米粒子。通过贵金属Pt掺杂TiO₂(Pt-TiO₂)、稀土元素Ce掺杂TiO₂(Ce-TiO₂)和Pt、Ce共掺杂TiO₂(Pt/Ce-TiO₂)的掺杂的方法对二氧化钛进行改性。通过XRD,XPS,TEM,紫外漫反射等表征手段对制备的样品进行表征。通过可见光下降解罗丹明B来测试其光催化活性。实验结果表明,由Ce掺杂的TiO₂光催化剂对有机污染物的最大降解能力略大于Pt掺杂的TiO₂,2种元素进行共同掺杂时对应的TiO₂光催化剂降解能力最大。     

A mini-review on rare earth metal-doped TiO<Subscript>2</Subscript> for photocatalytic remediation of wastewater

Titanium dioxide (TiO₂) has been considered a useful material for the treatment of wastewater due to its non-toxic character, chemical stability and excellent electrical and optical properties which contribute in its wide range of applications, particularly in environmental remediation technology. However, the wide band gap of TiO₂ photocatalyst (anatase phase, 3.20 eV) limits its photocatalytic activity to the ultraviolet region of light. Besides that, the electron-hole pair recombination has been found to reduce the efficiency of the photocatalyst. To overcome these problems, tailoring of TiO₂ surface with rare earth metals to improve its surface, optical and photocatalytic properties has been investigated by many researchers. The surface modifications with rare earth metals proved to enhance the efficiency of TiO₂ photocatalyts by way of reducing the band gap by shifting the working wavelength to the visible region and inhibiting the anatase-to-rutile phase transformations. This review paper summarises the attempts on modification of TiO₂ using rare earth metals describing their effect on the photocatalytic activities of the modified TiO₂ photocatalyst.     

Titania-supported silver-based bimetallic nanoparticles as photocatalysts

Photocatalytic process has shown recently a great potential as an environmental friendly and clean remediation technology for organic pollutants in wastewater. This work described the synthesis of silver-based bimetallic nanoparticles using colloid chemistry and the subsequent immobilization onto titania to form composite photocatalytic materials (titania-supported Ag–Pt nanoparticles). The photocatalysts were characterized by X-ray diffraction, electron microscopy, and nitrogen physisorption. The catalytic activity of the photocatalysts was evaluated by photocatalytic degradation of phenol and 2-chlorophenol (2-CP) in synthetic wastewater solutions. The photocatalytic processes were conducted in a batch photoreactor containing appropriate solutions of phenol and 2-CP with UV irradiation of 450 W. UV-visible spectrophotometer was used for analyzing the concentration of phenol and 2-CP in solutions. Parameters affecting the photocatalytic process such as the solution pH, phenol and 2-CP concentrations, and catalyst concentration were investigated. The results obtained revealed that TiO₂-supported Ag/Pt nanoparticles showed a higher activity for UV-photocatalytic degradation of both phenol and 2-CP pollutants in the solution (as compared to the plain rutile TiO₂). The photodegradation processes were optimized by the 0.5-g/L catalyst with a pollutant concentration of 50 mg/L for all the samples. Complete degradation for both phenol and 2-CP was achieved after 120 min.     

Performance evaluation and application of surface-molecular-imprinted polymer-modified TiO2 nanotubes for the removal of estrogenic chemicals from secondary effluents

The removal of estrogenic chemicals during wastewater reclamation has been a great concern. Current advanced treatment processes are inefficient for the removal of estrogenic chemicals from secondary effluents of municipal wastewater treatment plants (WWTPs) due to the coexistence of other pollutants with less environmental significance which are also removed simultaneously. The search for highly selective and low-cost removal methods is warranted. Therefore, surface-molecular-imprinted polymer-modified TiO₂ nanotube (S-MIP-TiO₂ NT) photocatalysts were fabricated, characterized, and tested for the removal of estrogenic pollutants from wastewater in this study for the first time. Scanning electron microscopy and Fourier-transform infrared spectroscopy studies showed that the TiO₂ NTs (with an average diameter of 60 nm) were successfully imprinted with functional groups (i.e., carboxyl). The adsorption selectivity and photocatalytic activity of the S-MIP-TiO₂ NTs towards template compound (17β-estradiol, E2) were improved, compared with neat TiO₂ NTs. Interestingly, S-MIP-TiO₂ NTs exhibited higher adsorption intensity and photocatalytic selectivity at low concentrations (from 10 ng/L to 100 μg/L, as normal estrogenic chemical concentrations in secondary effluents) of E2 than that at high concentrations (from 10 to 1,000 mg/L). It was also found that some representative estrogenic chemicals and estrogenic activity could be selectively and rapidly removed from secondary effluents of municipal wastewater treatment plants using S-MIP-TiO₂ NTs as photocatalysts. In addition, S-MIP-TiO₂ NT photocatalysts exhibited excellent regeneration characteristics. Photocatalytic treatment using S-MIP-TiO₂ NTs could be a promising approach for the effective removal of estrogenic chemicals from secondary effluents of municipal WWTPs.     

High-performance for hydrogen evolution and pollutant degradation of reduced graphene oxide/two-phase g-C<Subscript>3</Subscript>N<Subscript>4</Subscript> heterojunction photocatalysts

We have successfully synthesized the composites of two-phase g-C₃N₄ heterojunction photocatalysts by one-step method. And the reduced graphene oxide/two-phase g-C₃N₄ heterojunction photocatalyst was fabricated via a facile hydrothermal reduction method. The characterization results indicated that the two-phase g-C₃N₄ was integrated closely, and the common phenomenon of agglomeration for g-C₃N₄ was significantly reduced. Moreover, the oxidized graphene was reduced successfully in the composites and the graphene was overlaid on the surface or the interlayers of g-C₃N₄ heterojunction composite uniformly. In addition, we have carried out the photocatalytic activity experiments by H₂ evolution and rhodamine B removal, tetracycline removal under the visible light irradiation. The results revealed that the composite has improved the separation efficiency a lot than the pure photocatalyst. The photocurrent test demonstrated that the recombination of electrons and holes were efficiently inhibited as well as enhanced the photocatalytic activity. The 0.4% rGO loaded samples, 0.4% rGOCN2, own the best performance. Its rate of H₂ evolution was 15 times as high as that of the pure g-C₃N₄.     

Photocatalytic behavior of nanosized TiO2 immobilized on layered double hydroxides by delamination/restacking process

Introduction

Efficient immobilization of TiO₂ nanoparticles on the surface of Mg₂Al-LDH nanosheets was performed by delamination/restacking process.

Experimental part

The structural and textural properties of as-prepared nanocomposite were deeply analyzed using different solid-state characterization techniques such as: X-ray powder diffraction, Fourier transform infrared spectroscopy, and Raman spectroscopies, chemical analysis, X-ray photoelecton spectroscopy, N₂ adsorption?Cdesorption, and electronic microscopy.

Results and discussion

The photocatalytic properties of immobilized TiO₂ nanoparticles on Mg₂Al were investigated using the photodegradation of two model pollutants: Orange II and 4-chlorophenol, and compared with pure colloidal TiO₂ solution.

Conclusion

It appears that Orange II photodegradation was systematically faster and more efficient than 4-chlorophenol photodegradation regardless of the medium pH. Moreover under slightly basic conditions, even if the TiO₂ photocatalytic efficiency decreases, photodegradation performed in presence of easily recovered TiO₂/Mg₂Al_1.5 nanocomposite gives rise to comparable or better results than pure TiO₂.     

Cu/La共掺杂TiO2光催化氧化水中的氨氮

采用水解-沉淀法制备了Cu/La共掺杂纳米TiO2催化剂,利用XRD、XPS和BET技术对其进行表征,并考察了在紫外灯下,共掺杂TiO2对氨氮的光催化氧化工艺条件。物相结构和比表面积测试结果表明,共掺杂催化剂具有较好的锐钛矿晶型,孔径分布为4～8 nm,Cu/La共掺杂TiO2La以La3+,Cu是以Cu2+、Cu+的形式掺杂进入TiO2的晶格。光催化实验表明:所得改性光催化剂对氨氮的去除及焦化废水的处理均具有较高的催化活性。     

The enhancement of photodegradation efficiency using Pt–TiO2 catalyst

This study investigates the mechanism of photosensitization and the recombination of excited electron–hole pairs affected by depositing platinum (Pt) on the surface of titanium dioxide (TiO₂). A new catalyst of Pt–TiO₂ was prepared by a photoreduction process. Being model reactions, the photocatalytic oxidation of methylene blue (MB) and methyl orange (MO) in aqueous solutions using the Pt–TiO₂ catalyst was carried out under either UV or visible light irradiation. The experimental results indicate that an optimal content of 0.75%Pt–TiO₂ achieves the best photocatalytic performance of MB and MO degradation and that the Pt–TiO₂ catalyst can be sensitized by visible light. The interaction of Pt and TiO₂ was investigated by means of UV–Vis absorption spectra, photoluminescence emission spectra, and X-ray photoelectron emission spectroscopy. The Pt⁰, Pt²⁺ and Pt⁴⁺ species existing on the surface of Pt–TiO₂, and the Ti³⁺ species existing in its lattice may form a defect energy level. The Pt impurities, including Pt, Pt(OH)₂, and PtO₂, and the defect energy level absorb visible light more efficiently in comparison with the pure TiO₂ and hinder the recombination rate of excited electron–hole pairs.     

Hydrogen production using thermocatalytic decomposition of methane on Ni<Subscript>30</Subscript>/activated carbon and Ni<Subscript>30</Subscript>/carbon black

Hydrogen is an energy carrier of the future need. It could be produced from different sources and used for power generation or as a transport fuel which mainly in association with fuel cells. The primary challenge for hydrogen production is reducing the cost of production technologies to make the resulting hydrogen cost competitive with conventional fuels. Thermocatalytic decomposition (TCD) of methane is one of the most advantageous processes, which will meet the future demand, hence an attractive route for CO_x free environment. The present study deals with the production of hydrogen with 30 wt% of Ni impregnated in commercially available activated carbon and carbon black catalysts (samples coded as Ni₃₀/AC and Ni₃₀/CB, respectively). These combined catalysts were not attempted by previous studies. Pure form of hydrogen is produced at 850 °C and volume hourly space velocity (VHSV) of 1.62 L/h g on the activity of both the catalysts. The analysis (X-ray diffraction (XRD)) of the catalysts reveals moderately crystalline peaks of Ni, which might be responsible for the increase in catalytic life along with formation of carbon fibers. The activity of carbon black is sustainable for a longer time compared to that of activated carbon which has been confirmed by life time studies (850 °C and 54 sccm of methane).     

Photocatalytic Degradation of an Organophosphorus Pesticide Phosalone in Aqueous Suspensions of Titanium Dioxide

Abstract

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO₂ particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. The half-life (DT₅₀) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K = 0.0532 min^?1). The half-life time of photomineralization in the concentration range of 7.5–20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

Photocatalytic discoloration of Methyl Orange by anatase/schorl composite: optimization using response surface method

The anatase/schorl composites were prepared and employed for the photocatalytic discoloration of an azo dye, Methyl Orange (MO). X-ray diffraction results indicated that TiO₂ existed in the form of anatase phase and no diffraction peaks of schorl could be observed for all the composite samples. Scanning electron micrographs showed that the particles of anatase were well deposited and dispersed on the surface of schorl. Photocatalytic experiments revealed that the anatase/schorl composites exhibited higher photocatalytic activity for MO discoloration than pure TiO₂ and more than 90 % discoloration ratio could be obtained within 60 min UV irradiation when the sample containing 3 wt.% of schorl as TiO₂ support was used. Then, the central composite design (CCD) under the response surface methodology (RSM) was employed for the experiment design and process optimization. The significance of a second-order polynomial model for predicting the optimal values of MO discoloration was evaluated by the analysis of variance (ANOVA) and 3D response surface plots for the interactions between two variables were constructed. Based on the model prediction, the optimum conditions for the photocatalytic discoloration of MO by TiO₂/schorl composite were determined to be 15?×?10^?3 mM MO initial concentration, 2.7 g/l photocatalyst dosage, solution pH 6.6 and 43 min reaction time, with a maximum MO discoloration ratio of 98.6 %. Finally, a discoloration ratio of 94.3 % was achieved for the real sample under the optimum conditions, which was very close to the predicted value, implying that RSM is a powerful and satisfactory strategy for the process optimization.     

Application of activated M/ZnO (M = Mn,Co, Ni,Cu, Ag) in photocatalytic degradation of diazo textile coloring dye

Activated ZnO powder has been prepared by procedures involving first its dissolution in nitric acid, then simultaneous treatment by adding NH₄OH and CO₂ bubbling leading to precipitation as Zn(OH)CO₃ (ZH) and further thermal decomposition of ZH at 400 °C. The gas evolution leads to formation of pores and increase in the specific surface area. Chemically activated M/ZnO powders doped with Mn, Co, Ni, Cu, and Ag have been obtained by the impregnation method. The samples have been characterized by ultraviolet-visible (UV-Vis) spectroscopy, diffuse reflectance (DR) UV-Vis, X-ray diffraction (XRD), single point Brunauer–Emmet–Teller (BET), scanning electron microscope (SEM), and X-ray photoelectron spectroscopy (XPS) methods. The experiments have shown that metal-doped activated ZnO powders possess higher photocatalytic activities in oxidative discoloration of model contaminant textile coloring dye Reactive Black 5 in slurry reactor compared to that of the pure ZnO. The XRD and XPS data have shown the presence of defects, nonstoichiometricity implying the formation of solid solutions. Copper-doped (1.5 wt%) activated ZnO (Cu²⁺ replaces Zn²⁺) is outstanding in its photocatalytic performance in discoloration of the dye due to the higher specific surface area and improved charge carrier separation.