山西省污染源自动监控系统的设计与实现

山西省重点污染源自动监控系统是集环境监测、监视和控制于一体的污染源自动监控系统,解决了传统污染源监控系统"只监不控"、"只监结果不监过程"的问题。介绍了该系统的组成、功能及技术特点,并于2010年3月通过该系统对超标排放企业远程监控的实施情况进行了分析。结果表明,该系统能够有效对监控企业进行实时监测,并对污染超标企业进行远程控制和警示,从而有效提高了环境监管水平和执法效率,加强了防止和应对突发性重大环境污染事故的能力。     

烟气黑度监测中应注意的问题

烟气中林格曼黑度的测定是通过将排放源出口处烟气颜色与林格曼烟气浓度图比较,当某一排气颜色与其中色块接近时,就认定烟尘浓度与该色块的黑度等级一致,该方法已广泛用于环境保护等监测部门。国家颁布的有关炉窑大气污染物排放标准中对烟气黑度作的规定和解释见表1。     

国家环境保护总局监测仪器质检中心实现了检定现场远程监控

近日 ,国家环境保护总局环境监测仪器质量监督检验中心 (简称质检中心 )建立了计算机远程监控检定现场烟气的在线动态监测系统 (ＣＥＭＳ系统 )。操作人员通过该系统就可随时查阅、监视任一厂家 (商 )被检ＣＥＭＳ系统的运行状态 (包括烟尘排放浓度、烟气排放浓度、烟气流速等测量参数的数据报表 )、实时测试图表以及历史数据 ,实现了无纸化办公 ,提高了工作效率国家环境保护总局监测仪器质检中心实现了检定现场远程监控     

沈阳殡葬行业烟气环境污染物排放现状

对9家火化场11台火化设备的运行状况进行监测,以火化废气环境污染因子烟尘、二氧化硫、一氧化碳、氮氧化物、氨气、硫化氢及烟气黑度为测试研究对象。火化设备中70%以上排放大气环境污染物超标,且50%排气筒高度低于15米,属于低空排放,对周边大气环境造成较重影响,全市90%火化场尚未安装烟气除尘净化设施,应引起上级主管部门和环境保护管理部门重视。     

燃煤电厂烟气排放过程监控系统设计与应用

介绍了燃煤电厂烟气排放过程（工况）监控系统的架构,排放过程监控子系统、参数监测子系统和数据采集传输子系统的实现方式,过程监控采集参数选择方法,模型建立步骤与验证方法。结合实际应用,分析如何判定脱硫设施运转正常,烟气参数监测是否正确,并提出了做好过程监控系统工作的相关建议。     

污染源排气自动监测氮氧化物的不确定度分析

使用烟气排放连续监测系统自动监测仪器测定污染源排气中氮氧化物,按照最新的《测量不确定度评定与表示》(JJF1059.1—2012)的要求,测量不确定度评定的要求,首次对其氮氧化物自动监测的不确定度进行分析,得出不确定度报告。     

智能化林格曼黑度检测系统设计与开发

针对传统林格曼黑度检测自动化程度低、不利于数据溯源等缺点,提出了一种基于自动烟气图像采集、GPRS自动上传、图像处理判定结果的智能化林格曼黑度检测系统。经过多次实地测定,该系统所测定的烟气黑度等级与人工测定的黑度等级一致。     

超低排放工艺下完全抽取式二氧化硫固定源在线监测设备全系统校准

为探索超低排放改造的固定源在线监测设备二氧化硫(SO_(2))全系统校准工作的开展情况,保障其自动监测数据的质量,利用标准物质对不同测量原理的自动监测设备进行分组试验。试验结果表明,热湿法自动监测设备在完成超低排放改造的高氨、高湿测量环境中适用性更强;造成冷干法自动监测设备SO_(2)全系统校准示值误差超标的原因为冷凝器铵盐结晶的吸附干扰;当待测烟气为高氨(>2 mg/m^(3))、高湿(>12.3%)测量环境时,14 h后SO 2全系统校准示值误差开始超过±2.5%的限值要求;在11%~13%的高湿测量环境中,磷酸滴定装置的氨逃逸水平<6 mg/m^(3)、除氨器+纳分除湿管装置的氨逃逸水平<15 mg/m^(3)时,解决铵盐结晶干扰的效果最佳。     

燃煤（油）固定污染源二氧化硫排放总量监测（二）：实测方法

燃煤（油）固定污染源二氧化硫排放总量监测（二）　　　　　──实测方法易江（中国环境监测总站１０００１２）接１９９５，９（３）：１６５～１８２。４固定污染源排放ＳＯ２总量实测方法监测ＳＯ２排放总量主要包括三方面的测量，即烟气参数的测定，烟气中ＳＯ２浓度...     

烟气连续监测系统的相对准确度检测

阐述了HJ／T76—2001《固定污染源排放烟气连续监测系统技术要求及检测方法》标准中烟气连续监测系统的相对准确度计算和相对准确度计算中存在的问题。对存在问题中的重复性或复现性的假设、B类不确定度的忽略、标准分析方法平均值的采用和偏差检验进行了探讨。     

A New Mathematical Approach in Environmental and Life Sciences: Gene–Environment Networks and Their Dynamics

An important research area in life sciences is devoted to modeling, prediction, and dynamics of gene-expression patterns. As clearly understood in these days, this enterprise cannot become satisfactory without acknowledging the role of the environment. To a representation of past, present, and most likely future states, we also encounter measurement errors and uncertainties. This paper surveys and improves recent advances in understanding the foundations and interdisciplinary implications of the newly introduced gene–environment networks, and it integrates the important theme of carbon dioxide emission reduction into the networks and dynamics. We also introduce some operational and managerial issues of practical working and decision making, expressed in terms of sliding windows, quadrants (modules) of parametric effects, and navigating (controlling) between such effects and directing them. Given data from DNA microarray experiments and environmental records, we extract nonlinear ordinary differential equations that contain parameters that have to be determined. For this, we employ modern (Chebychevian) approximation and (generalized semi-infinite) optimization. After this is provided, time- discretized dynamical systems are studied. A combinatorial algorithm with polyhedra sequences allows to detect the region of parametric stability. Finally, we analyze the topological landscape of gene–environment networks with its structural (in)stability. By embedding as a module and investigating CO₂ emission control and figuring out game theoretical aspects, we conclude. This pioneering work is theoretically elaborated, practically devoted to health care, medicine, education, living conditions, and environmental protection, and it invites the readers to future research.      

微波消解-原子吸收光度法测定土壤中铜锌铅镉镍铬

用微波消解－原子吸收光度法测定土壤中铜，锌，铅，镉，镍和铬。通过硝酸－氢氟酸－过氧化氢体系消解液对土壤样品消解，选择出微波最佳消解条件。对硝酸－盐酸－过氧化氢体系消解液和硝酸－氢氟酸－过氧化氢体系消解液进行消解对比试验，发现前者不能将土壤样品完全消解，后者能将样品消解完全，但需将消解液中剩余的酸赶尽，否则测定结果将明显偏低。微波消解土壤与传统电热消解相比，操作简便快速，可提高工作效率。     

Topsoil and Housedust Metal Concentrations in the Vicinity of a Lead Battery Manufacturing Plant

The aim of the study was to determine the extent of heavy metal pollution in the vicinity of a lead battery manufacturing plant in the Czech Republic, both in the general environment and within homes. Topsoils (0–5 cm) were sampled from 100 sites along 4 transects which crossed the battery factory, the town centre and outlying rural areas. Housedust samples were collected from 15 plant-workers' homes and 15 non plant-workers' homes located at various distances from the factory. Samples were analysed for levels of Pb, Zn, Cd, Cu, As and Sb, using ICP-AES. Soil concentrations of Pb, Cd, As and Sb peaked at the perimeter fence of the battery factory with Pb levels of up to 12 650 g g> ^-1. Concentrations of these metals decreased exponentially within 500 m of the plant. Whilst the battery factory does appear to be a source of all the metals with the exception of Zn, emissions do not appear to be transported to any great extent over distances of more than 0.5 km. Topsoil and housedust concentrations of Pb, Zn, Cd, Cu, As and Sb in the general Mlada Boleslav area do not appear to be significantly different from those recorded in a large scale survey of urban soils in the United Kingdom. A comparison of housedust Pb concentrations in homes of plant workers and non-plant workers suggests that there may be a small input of Pb into the home environment by battery plant employees.     

An Overview of Contaminant-Related Issues Identified by Monitoring in San Francisco Bay

The San Francisco Estuary Regional Monitoring Program for Trace Substances (RMP) began in 1993 and is sponsored by 74 local, state, and federal agencies and companies through their discharge or Bay use permits. The RMP monitors water, sediment, toxicity, and bivalve bioaccumulation at 25 sites in the Bay that are considered to represent "background" conditions. Several major environmental issues have been identified by the RMP. Polychlorinated biphenyls and mercury were often above water quality guidelines, and often occurred in fish tissues above U.S. Environmental Protection Agency (U.S. EPA) screening values. Concentrations do not appear to be decreasing, suggesting continuing inputs. Episodes of aquatic toxicity often occurred following runoff events that transport contaminants into the Bay from urbanized and agricultural portions of the watershed. Sediment toxicity occurred throughout the Bay, and has been correlated with concentrations of specific contaminants (chlordanes, polynuclear aromatic hydrocarbons) at some locations; mixtures of contaminants were probably also important. Since the RMP does not monitor all ecosystem components, assessments of the overall condition of the Bay cannot be made. However, in terms of contamination, the RMP samples suggest that the South Bay, and North Bay sites are moderately contaminated.     

Biomagnification factors (fish to Osprey eggs from Willamette River,Oregon, U.S.A.) for PCDDs,PCDFs, PCBs and OC pesticides

A migratory population of 78 pairs of Osprey (Pandion haliaetus) nesting along the Willamette River in westernOregon was studied in 1993. The study was designed to determinecontaminant concentrations in eggs, contaminant concentrationsin fish species predominant in the Ospreys diet, andBiomagnification Factors (BMFs) of contaminants from fish specieseaten to Osprey eggs. Ten Osprey eggs and 25 composite samplesof fish (3 species) were used to evaluate organochlorine (OC)pesticides, polychlorinated biphenyls (PCBs), polychlorinateddibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans(PCDFs). Mercury was also analyzed in fish. Geometric meanresidues in Osprey eggs were judged low, e.g., DDE 2.3 g g^-1 wet weight (ww), PCBs 0.69 g g^-1, 2,3,7,8-TCDD 2.3 ng kg^-1, and generally well below known threshold values for adverse effects on productivity, and the population was increasing. Osprey egg residue data presentedby River Mile (RM) are discussed, e.g., higher PCDDs were generally found immediately downstream of paper mills and eggsfrom the Willamette River had significantly elevated PCBs and PCDDs compared to reference eggs collected nearby in the CascadeMountains. Prey remains at nest sites indicated that the Largescale Sucker (Catostomus macrocheilus) and NorthernPikeminnow (Ptychocheilus oregonensis) accounted for an estimated 90.1% of the biomass in the Osprey diet, and composite samples of these two species were collected from different sampling sites throughout the study area for contaminant analyses. With the large percentage of the fishbiomass in the Osprey diet sampled for contaminants (and fisheaten by Ospreys similar in size to those chemically analyzed),and fish contaminant concentrations weighted by biomass intake, a mean BMF was estimated from fish to Osprey eggs for the largeseries of contaminants. BMFs ranged from no biomagnification(0.42) for 2,3,7,8-TCDF to 174 for OCDD. Our findings for themigratory Osprey were compared to BMFs for the resident HerringGull (Larus argentatus), and differences are discussed. Webelieve a BMF approach provides some basic understanding ofrelationships between contaminant burdens in prey species offish-eating birds and contaminants incorporated into their eggs,and may prove useful in understanding sources of contaminants inmigratory species although additional studies are needed.     

An investigation on biological stability of product water generated by lab-scale and pilot-scale distillation systems

Material Disposal Area G is the primary low-levelradioactive waste disposal site at Los Alamos NationalLaboratory, New Mexico, and is adjacent to Pueblo of SanIldefonso lands. Pueblo residents and Los Alamos scientists areconcerned about radiological doses resulting from uptake of AreaG radionuclides by mule deer (Odocoileus hemionus) andRocky Mountain elk (Cervus elaphus), then consumption ofdeer and elk meat by humans. Tissue samples were collected fromdeer and elk accidentally killed near Area G and were analyzedfor ³H, ⁹⁰Sr, total U, ²³⁸Pu, ^{239, 240}Pu,²⁴¹Am, and ¹³⁷Cs. These data were used to estimatehuman doses based on meat consumption of 23 kg y^-1. Humandoses were also modeled using RESRAD, and dose rates to deer andelk were estimated with a screening model. Dose estimates tohumans from tissue consumption were 2.9 × 10^-3 mSv y^-1and 1.6 × 10^-3 mSv y^-1 from deer and elk, respectively,and RESRAD dose estimates were of the same order of magnitude. Estimated dose rates to deer and elk were 2.1 × 10^-4 mGyd^-1 and 4.7 × 10^-4 mGy d^-1, respectively. Allestimated doses were significantly less than established exposurelimits or guidelines.     

The Draft of the New German Guideline VDI 3782/8 to Model Automobile Exhaust Dispersion

The draft of the German guideline to calculate automobile exhaust dispersion is explained. It contains a two-stage-system: For first quick estimates the guideline contains the simple models MLuS and STREET. In case these models are not applicable or their results shows concentration levels close to the air quality standards, the more complex models PROKAS_V and MISKAM are recommended. PROKAS_V is a Gaussian plume model, MISKAM is a 3-dimensional microscale non hydrostatic flow model for built-up areas with an Eulerian dispersion model. The guideline comprises cases in rural areas without or with few adjacent buildings as well as urban areas with buildings near the roads. The contribution gives information about the models, typical results and some of the problems showing up presently.     

Hydrocarbon Utilization in Yeast Isolates Found to Grow in Association with Petroleum in a Polluted Ultisol of Midwestern Nigeria

The population counts of hydrocarbon-utilising yeasts weremonitored at six sampling stations in the Benin City municipalarea over a four-week period. Although the population countswere relatively constant in each locality, the highest countsoccurred in areas heavily polluted by domestic and industrialeffluents. A total of thirty-five hydrocarbon-degrading yeastswere isolated from soil at the sampling stations usingn-hexadecane as sole carbon source. The isolates were identifiedas belonging to the genera Candida (27 strains), Endomycopsis (4 strains). All the organisms grew on long-chainn-alkane, kerosene, diesel oil and crude oil but failed to growon short-chain n-alkane, aromatic and alicyclic hydrocarbons.Measurement of growth attributes of the isolates usingn-hexadecane, diesel oil and crude oil as substrates showed thatthe Candida species were better utilizers of hydrocarbonsubstrates relative to Endomycopsis and Schizosaccharomyces species.     

Hydrologic–Economic Model for Managing Irrigation Intensity in Irrigation Areas under Watertable and Soil Salinity Targets

This paper gives mathematical details and sample applications of SWAGMAN Farm (SWAGMAN, Salt Water and Groundwater Management), a farm-scale hydrologic economic model that integrates agronomic, climatic, irrigation, hydrogeological and economic aspects of irrigated agriculture. The model is capable of determining optimum mix of land use to keep watertable and soil salinity within acceptable limits while maximising the economic returns. Alternatively, the model can simulate water and salt balance and economics of a given cropping preference. Web-based and Geographic Information Systems versions of the model are available for integration with the environmental reporting systems of the irrigation areas.     

Assessing health consequences in an environmental impact assessment: The case of Amsterdam Airport Schiphol

In this article a comprehensive approach for the evaluation of possible health effects in an environmental impact assessment (EIA) is described, illustrated with the example of Amsterdam Airport Schiphol. Unlike many EIAs, we estimated quantitatively the impact of aircraft-related pollution in terms of the number of affected people for aircraft noise annoyance, odour annoyance and hypertension. In addition, an analysis of health registry data on cardiovascular and respiratory diseases and a short survey on annoyance and risk perception were carried out. The scope of a health impact assessment depends on the situation, available knowledge and data, concern in the population about the impact and the number of people concerned. It is important to pay attention to the perception of risks and concerns from all parties involved. Moreover, the results demonstrate that far more people outside the area for which standards apply were affected than inside.