Evaluation of beech for production of bio-char,bio-oil and gaseous materials

Evaluation of Oriental beech (Fagus orientalis L.) was investigated with aspect of thermo-chemical conversion to obtain bio-char, bio-oil and gaseous. When the pyrolysis temperature increased, the bio-char yield decreased. A high temperature and smaller particles increase the heating rate resulting in a decreased bio-char yield. The bio-char obtained are carbon rich, with high heating value and relatively pollution-free potential solid biofuel. The liquefaction yield sharply increased with increasing the temperature near critical temperature and after that. In the pyrolysis, increases of liquid yields are considerably sharply for all of the samples with increasing of pyrolysis temperature from 690 K to 720 K. The beechnut oil was converted to biodiesel in supercritical methanol without using the catalyst. Experiments have been carried out in an autoclave at 493, 523 and 593 K, and with molar ratios of 1:6–1:40 of the oil to methanol. The yield of alkyl ester increased with increasing the molar ratio of oil to alcohol.     

An Experimental Study on Pyrolysis of Biomass

In this study, pyrolysis of sugarcane bagasse was performed in fixed bed tubular reactor under the conditions of nitrogen atmosphere, by varying temperature and different particle sizes. The effect of final pyrolysis temperature from 400 to 500°C and the nitrogen flow rate from 50 to 200 cc min⁻¹ on the pyrolysis product yields from sugarcane bagasse have been investigated. The Maximum bio-oil yield obtained is 24.12 wt% at the final pyrolysis temperature of 450°C, N₂ flow rate of 50 cc min⁻¹ and particle size of mesh number −8 + 12. The yield of bio-oil decreases with increase in temperature from 450 to 550°C and N₂ flow rate from 50 to 200 cc min⁻¹. The various characteristics of pyrolysis oil obtained under these conditions were identified on the basis of standard test methods. The empirical formula of pyrolysis oil with a heating value of 37.01 MJ Kg⁻¹ was established as CH_1.434 O_0.555 N_0.004. The results from the pyrolysis show the potential of sugarcane bagasse as an important source of liquid hydrocarbon fuel.     

Experimental study of the characteristics of solid fuel from fry-dried swine excreta

Swine excreta were dried by boiling via immersion in hot oil. In this method, moisture in the excreta is replaced with oil or evaporated by turbulent heat transfer in high-temperature oil. The dried excreta can be used in an incinerator like low-rank coal or solid fuel. Refined waste oil and B–C heavy oil were used for drying. Drying for 8 min at 150 °C reduced the water content of raw excreta from 78.90 wt.% to 1.56 wt.% (refined waste oil) or 1.62 wt.% (B–C heavy oil) and that of digested excreta from 79.58 wt.% to 3.40 wt.% (refined waste oil) or 3.48 wt.% (B–C heavy oil). The low heating values of the raw and digested excreta were 422 kJ/kg and ?2,713 kJ/kg, respectively, before drying and 27,842–28,169 kJ/kg and 14,394–14,905 kJ/kg, respectively, after drying. A heavy metal analysis did not detect Hg, Pb, Cd, As, and Cr in the dried excreta, but Al, Cu, and Zn, which occur in the feed formula, were detected. Thermogravimetric analysis before and after drying revealed that emission of volatiles and combustion of volatiles and fixed carbon occurred at temperatures of 250–500 °C when air was used as the transfer gas.     

The effects of activated Al2O3 on the recycling of light oil from the catalytic pyrolysis of waste printed circuit boards

The effects of employing activated Al₂O₃ during the catalytic pyrolysis of waste printed circuit boards (WPCBs) are investigated, focusing on the recycling of light oil. Variations in the pyrolysis process are studied through analysis of the phase distribution, water content and boiling point fractions of the resulting products. Product composition and carbon number distribution are analyzed using gas chromatography techniques. The use of activated Al₂O₃ increases the light oil fraction and also reduces the quantity of brominated products formed. It was determined that the best yield of light oil and most efficient debromination resulted from catalytic pyrolysis at 600 °C. Applying catalyst-to-feed ratios in the range of 1.0–1.5 also maximizes the yield of light oil. The major oil fraction resulting from catalytic pyrolysis has a boiling point range of 0–250 °C and carbon number range of C6–C9, showing for use as a potential fuel after suitable treatment such as hydrogenation. At a higher catalyst-to-feed ratio of 2.0, activated Al₂O₃ generates a high proportion of light oil fractions containing a significant quantity of chemicals such as phenol (52.67% at 600 °C), although an overall lower yield of oil is obtained. The oil produced in this manner may also be used as a raw material feedstock for the production of various other useful chemicals.     

Feasibility of honeycomb monolith supported sugar catalyst to produce biodiesel from palm fatty acid distillate (PFAD)

Carbon coated monolith was prepared by sucrose solution 65 wt.% via dip-coating method. Sulfonation of incomplete carbonized carbon coated monolith was carried out in order to synthesize solid acid catalyst. The textural structure characteristics of the solid acid catalyst demonstrated a low surface area and pore volume. Palm fatty acid distillate (PFAD), a by-product of palm oil refineries, was utilized as oil source in biodiesel production. The esterification reaction subjected to different reaction conditions was performed by using the sulfonated carbon coated monolith as heterogeneous catalyst. The sulfonation process had been performed by using vapour of concentrated H₂SO₄ that was much easier and efficient than liquid phase sulfonation. Total acidity value of carbon coated monolith was measured for unsulfonated sample (0.5 mmol/g) and sulfonated sample (4.2 mmol/g). The effect of methanol/oil ratio, catalyst amount and reaction time were examined. The maximum methyl ester content was 89% at the optimum condition, i.e. methanol/oil molar ratio (15:1), catalyst amount (2.5 wt.% with respect to PFAD), reaction time (240 min) and temperature 80 °C. The sugar catalyst supported on the honeycomb monolith showed comparable reactivity compared with the sugar catalyst powder. However, the catalyst reusability studies showed decrease in FFA% conversion from 95.3% to 68.8% after four cycles as well as the total acidity of catalyst dropped from the value 4.2 to 3.1 mmol/g during these cycles. This might be likely due to the leaching out of SO₃H group from the sulfonated carbon coated monolith surface. The leaching of active species reached a plateau state after fourth cycle.     

Evaluation of membrane bioreactor for hypersaline oily wastewater treatment

Produced water is a significant waste stream generated in association with oil and gas production. It contains high concentrations of hydrocarbon constituents and different salts. In this study, a membrane sequencing batch reactor (MSBR) was used to treat synthetic and real produced water. The MSBR was evaluated in terms of biodegradation of hydrocarbons in the synthetic produced water with various organic loading rates (OLR) (0.281, 0.563, 1.124, 2.248, and 3.372 kg COD/(m³ day)), cycle time (12, 24, and 48 h), and membrane performance. The effects of salt concentrations at different total dissolved solids (TDS) (35,000, 50,000, 100,000, 150,000, 200,000, and 250,000 mg/L) on biological treatment of the pollutants in the synthetic and real wastewater were studied. At an OLR of 1.124 kg COD/(m³ day), an HRT of 48 h and TDS of 35,000 mg/L, removal efficiencies of 97.5%, 97.2%, and 98.9% of COD, total organic carbon (TOC), and oil and grease (O&G), respectively were achieved. For the real produced water, removal rates of 86.2%, 90.8%, and 90% were obtained for the same conditions. However, with increasing salt content, the COD-removal efficiencies of the synthetic and real produced water were reduced to 90.4% and 17.7%, respectively at the highest TDS.     

Synthesis of Bio-Diesel and Bio-Lubricant by Transesterification of Vegetable Oil with Lower and Higher Alcohols Over Heteropolyacids Supported by Clay (K-10)

The use of different lower and higher alcohols viz; methanol, ethanol, n-propanol and n-octanol, for the synthesis of methyl, ethyl, propyl and octyl fatty acid esters by transesterification of vegetable oil (triglycerides) with respective alcohols also known as ‘Bio-diesel’ and ‘Bio-lubricants’ was studied in detail. The reactions were carried out in a batch process. The activity with different supports like clay (K-10), activated carbon, ZSM-5, H-beta and TS-1 were compared. The superacids (heteropolyacids, HPA) viz; Dodeca-Tungstophosphoric acid [H₃PO₄·12 WO₃·xH₂O] (TPA) and Dodeca-Molybdo phosphoric acid ammonium salt hydrate [H₁₂Mo₁₂N_3-O₄₀P + aq] (DMAA) was used to increase the acidity and so the activity by loading on the most active support viz; clay (K-10). These HPA loaded on clay as a catalyst was used for the following study: effect of percent HPA loading on clay, effect of different vegetable oils, effect of different alcohols on the triglyceride conversion based on glycerol formation and selectivity based on alkyl esters formation. The data is compared at the best-optimized identical set of operating reaction conditions: 170 °C, 170 rpm, catalyst loading: 5% (w/w of reaction mixture), molar ratio (oil: alcohol): 1:15 and time on stream of 8 h. The generated data is also evaluated based on the reported one.     

Boron removal from produced water using electrocoagulation

Produced water is the largest wastestream of oil and gas exploration but its chemical composition hinders its beneficial use. Effective treatment and reuse of produced water can mitigate scarcity of fresh water, especially in arid areas. Presence of inorganic compounds such as boron in produced water renders its beneficial use difficult. In this study, boron removal from produced water was investigated. Synthetic wastewater was prepared simulating the range of boron concentrations in produced water. Four operating parameters pH (3–11), charge loading (1200–3600 Ah/m³), contact time (15–90 min) and concentration (10–30 mg/L) were selected and their optimum conditions investigated. The obtained optimum conditions were applied to treat real produced water. Residual boron concentration of 0.3 mg/L was obtained from initial boron concentration of 15 mg/L in real produced water at optimum conditions of pH 7, charge loading 2400 Ah/m³ and contact time 90 min. Boron adsorption could be represented by Langmuir and Freundlich isotherm models. Electrocoagulation can be used for the effective removal of boron from produced water.     

Artificial neural network modelling of As(III) removal from water by novel hybrid material

The present study reported a method for removal of As(III) from water solution by a novel hybrid material (Ce-HAHCl). The hybrid material was synthesized by sol–gel method and was characterized by XRD, FTIR, SEM–EDS and TGA–DTA. Batch adsorption experiments were conducted as a function of different variables like adsorbent dose, pH, contact time, agitation speed, initial concentration and temperature. The experimental studies revealed that maximum removal percentage is 98.85 at optimum condition: pH = 5.0, agitation speed = 180 rpm, temperature = 60 °C and contact time = 80 min using 9 g L⁻¹ of adsorbent dose for initial As(III) concentration of 10 mg L⁻¹. Using adsorbent dose of 10 g L⁻¹, the maximum removal percentage remains same with initial As(III) concentration of 25 mg L⁻¹ (or 50 mg L⁻¹). The maximum adsorption capacity of the material is found to be 182.6 mg g⁻¹. Subsequently, the experimental results are used for developing a valid model based on back propagation (BP) learning algorithm with artificial neural networking (BP-ANN) for prediction of removal efficiency. The adequacy of the model (BP-ANN) is checked by value of the absolute relative percentage error (0.293) and correlation coefficient (R² = 0.975). Comparison of experimental and predictive model results show that the model can predict the adsorption efficiency with acceptable accuracy.     

Dilute Acid Hydrolysis of Cellulose and Cellulosic Bio-Waste Using a Microwave Reactor System

The dilute acid hydrolysis of grass and cellulose with phosphoric acid was undertaken in a microwave reactor system. The experimental data and reaction kinetic analysis indicate that this is a potential process for cellulose and hemi-cellulose hydrolysis, due to a rapid hydrolysis reaction at moderate temperatures. The optimum conditions for grass hydrolysis were found to be 2.5% phosphoric acid at a temperature of 175°C. It was found that sugar degradation occurred at acid concentrations greater than 2.5% (v/v) and temperatures greater than 175°C. In a further series of experiments, the kinetics of dilute acid hydrolysis of cellulose was investigated varying phosphoric acid concentration and reaction temperatures. The experimental data indicate that the use of microwave technology can successfully facilitate dilute acid hydrolysis of cellulose allowing high yields of glucose in short reaction times. The optimum conditions gave a yield of 90% glucose. A pseudo-homogeneous consecutive first order reaction was assumed and the reaction rate constants were calculated as: k₁ = 0.0813 s⁻¹; k₂ = 0.0075 s⁻¹, which compare favourably with reaction rate constants found in conventional non-microwave reaction systems. The kinetic analysis would indicate that the primary advantages of employing microwave heating were to: achieve a high rate constant at moderate temperatures: and to prevent ‘hot spot’ formation within the reactor, which would have cause localised degradation of glucose.     

Disintegration of municipal waste activated sludge by simultaneous combination of acid and ultrasonic pretreatment

The individual and simultaneous effects of acid and ultrasonic pretreatment on the disintegration of municipal waste activated sludge (WAS) were investigated based on chemical properties of WAS. In the combination of acid and ultrasonic pretreatment methods (ultrasonic-acid pretreatment), lowering pH accelerated and enhanced the disintegration of waste biological sludge. Therefore, the same disintegration efficiency (obtained by ultrasonic pretreatment alone) was achieved by the combined pretreatment in shorter sonication times. Optimum pretreatment conditions were ultrasonic power density of 1.0 W/mL and pretreatment time of 10 min for ultrasonic pretreatment alone, and ultrasonic power density of 1.0 W/mL, pretreatment time of 10 min and initial sludge pH of 2.0 for the combined pretreatment. Sludge disintegration degrees were about 30% and 40% under these optimized conditions, respectively. Optimum sludge concentration was found to be 1.0% total solid (TS) content for the combined pretreatment. As a result, ultrasonic-acid pretreatment has been determined as a new and effective combined sludge pretreatment method to improve the sludge disintegration.     

Chemical conversion of paper industry effluents into carboxymethylcellulose

The synthesis of carboxymethylcellulose was investigated using effluents containing short cellulose fibers. Carboxymethylcellulose was synthesized according to the slurry process using different amount of sodium hydroxide and different incubation times at 30 °C after the etherification reaction as variables. Characterization of the product was conducted by Fourier transformed infrared spectroscopy, X-ray diffraction, degree of substitution, average degree of polymerization, water imbibing capacity, color, rheological properties, apparent viscosity and trace elements content. Incubation time slightly increased the yield of the reaction and the degree of substitution during the first 12 h. The reaction yield and degree of substitution both decreased when the initially concentration of NaOH was increased from 7.0 g/mL to 10.5 g/mL. The carboxymethylcellulose obtained was darker and had lower hydration properties than commercial samples. Trace elements content suggests that the product could be only used in paint factories or building materials industries.     

Ion exchange membrane-assisted electro-activation of aqueous solutions: Effect of the operating parameters on solutions properties and system electric resistance

The properties of electro-activated (EA) aqueous solutions as well as the dynamics of their changes were considered in the current study using aqueous solutions of NaCl and NaHCO₃. The concentrations of the salt solutions were 0.5, 0.25, 0.125 and 0.05 M. The tests were performed at the DC current densities of 25, 37.5, and 50 Å/m². The electro-activation reactor consisted of three individual cells assembled together and separated by anion-exchange (AEM) and cation-exchange (CEM) membranes. During the experiments, four configurations of the membrane placements and solutions concentrations were studied. The obtained results showed the dynamics of the electro-activation process that allows obtaining electro-activated solutions with targeted properties such as pH and oxydo-reduction potential (ORP). It was possible to obtain electro-activated solutions at the anodic side (acid anolyte) with pH of 3.0, 3.5, and 4.0 and ORP of +1100 ± 15 mV when NaCl solution was used as electrolyte. Furthermore, several types of electro-activated solutions with high redox potential (ORP = +921 ± 12 mV) and neutral pH (6.48 ± 0.05) were obtained on the anode side when sodium carbonate was used. At the same time, two types of solutions, one with acid pH (2.14 ± 0.14) and the other one with alkaline pH (10.46 ± 0.03) with ORP = +689 ± 10 and 110 ± 21 mV, respectively, were obtained in the central compartment which considered as electro-activated solutions obtained by means of noncontact electro-activation.     

Evaluative comparison of two methods for SADT determination (UN H.1 and H.4)

We present our results on the comparison of two methods for the SADT determination. Both methods, UN test H.1 and UN test H.4 are recommended by the international transport regulations from the UN. But during the last years the applicability of the UN test H.4 has been questioned for solid substances. Therefore, three organic peroxides and one self-reactive substance have been investigated in 5 kg and 20 kg packages as well as in the UN test H.4 in a 500 mL Dewar vessel. The SADT values determined with the different methods match. The UN test H.4 seems to be well suited for solid organic peroxides and self-reactive substances of at least 20 kg or 60 L.     

Full-scale experimental studies for backdraft using solid materials

The backdraft experiments involved three full-scale room fire tests that used solid furnishing, loveseats. From experimental data, a backdraft caused two temperature peaks. The first one was below 600 °C. Then, an abrupt opening of the front door led to a supply of a large amount of fresh air, followed by an indication of sudden temperature rise. The second peak temperature was over 600 °C. Meanwhile, the deflagration resulted in the gases heating and expanding within the fire space, thus forcing unburned gases out of the vent ahead of the flame front. Comparing both cases with natural gas and solid loveseat as the fuel in backdraft, the former can achieve pre-mixture state and readily create an instant explosion wave phenomenon; however, this wave disappeared immediately. On the other hand, the solid loveseat used as the fuel in this study produced backdraft within 30–50 s after opening of the door. After the occurrence of backdraft, fire maintained a period of fully developed stage, which was consistent with the conditions in actual fires.     

Using a cluster randomized controlled trial to determine the effects of intervention of battery and hardwired smoke alarms in New South Wales,Australia: Home fire safety checks pilot program

IntroductionIn 2014, Fire & Rescue New South Wales piloted the delivery of its home fire safety checks program (HFSC) aimed at engaging and educating targeted top “at risk” groups to prevent and prepare for fire. This pilot study aimed to assess the effectiveness of smoke alarms using a cluster randomized controlled trial.MethodsSurvey questionnaires were distributed to the households that had participated in the HFSC program (intervention group). A separate survey questionnaire was distributed to the control group that was identified with similar characteristics to the intervention group in the same suburb. To adjust for potential clustering effects, generalized estimation equations with a log link were used.ResultsMultivariable analyses revealed that battery and hardwired smoking alarm usage increased by 9% and 3% respectively among the intervention group compared to the control group. Females were more likely to install battery smoke alarms than males. Respondents who possessed a certificate or diploma (AOR = 1.31, 95% CI 1.00–1.70, P = 0.047) and those who were educated up to years 8–12 (AOR = 1.32, 95% CI 1.06–1.64, P = 0.012) were significantly more likely to install battery smoke alarms than those who completed bachelor degrees. Conversely, holders of a certificate or diploma and people who were educated up to years 8–12 were 31% (AOR = 0.69, 95% CI 0.52–0.93, P = 0.014) and 24% (AOR = 0.76, 95% CI 0.60–0.95, P = 0.015) significantly less likely to install a hardwired smoke alarm compared to those who completed bachelor degrees.ConclusionsThis pilot study provided evidence of the benefit of the HFSC in New South Wales. Practical Applications: Fire safety intervention programs, like HFSC, need to be targeted to male adults with lower level of schooling even when they are aware of their risks.     

Characterization of fall patients: Does age matter?

IntroductionEvaluating age-specific fall characteristics is important for prevention programs. The aim was to characterize fallers who presented to our trauma center. We hypothesized that fall characteristics and outcomes would vary with age.MethodsData were retrospectively collected from the trauma registry and electronic medical records during January 1st, 2014-December 31st, 2015. Data were analyzed by Chi-square test with Yates’ continuity correction and one-way ANOVA with Bonferroni’s multiple comparisons test.ResultsThere were 1541 fallers, 814 (52.8%) were male. Ages ranged from 11 months to 100 years. The admission rate was high at 86%, with an average hospital stay of 5.7 days. Patients in the 0-18 and 19-45 age groups spent significantly less time in the hospital (p < 0.0001). Elderly patients had the highest average injury severity score (p < 0.0001). However, the youngest patients required surgery more often (p = 0.0004). The overall mortality rate was 3.6% and 52.8% were male. The mortality rate increased with age, from 0% for the 0-18 age group to 6.9% for patients ≥ 65 years of age. Remarkably, fallers in the 19-45 and 46-64 age groups predominantly died from ground level falls even though the average fall height in these groups was the highest (p < 0.0001). More fallers in the 19-45 and 46-64 age groups tested positive for alcohol/drug use (p < 0.0001). Middle-aged and elderly patients were more likely to be discharged to a skilled nursing or rehabilitation facility compared to younger patients who were discharged home.Conclusions and practical applicationsFall characteristics and outcomes varied with age. Data on age-specific characteristics, outcomes, and risk factors of falls will help in developing targeted interventions and may lead to better approaches to treat patients.     

Anaerobic digestion modeling of the main components of organic fraction of municipal solid waste

The organic fraction of municipal solid waste (OFMSW) is composed of several heterogeneous organic and inorganic wastes. The diversity of composition, the high volatile solid content and the biodegradable material that this waste offers make it quite an interesting option for anaerobic digestion (AD). Depending on the substrate composition, the biological degradation and kinetics of the AD could vary. Biochemical methane potential (BMP) tests are used as a tool to evaluate the methane production of several fractions of OFMSW, in order to study the influence of each fraction in the final mixture. The kinetic parameters of methane curves and the prediction of final productions are studied by different approaches to model equations using linear, exponential, logistic and Gaussian models. The analyses of the fractions indicate that organic substrates such as meat/fish which are in a small proportion in the final mixture, obtain major productivities (291 ± 3 mlCH₄/gVS), however others such as paper (217 ± 5 mlCH₄/gVS) could have their productivity enhanced due to their high VS present in the final mixture. Both the Gomperzt and the first order model fit reasonably with all the fractions, although substrates with lag phase adjust only to the Gompertz model explaining 99% of the experimental results.     

Effect of ultrasound irradiation and Ni-loading on properties and performance of CeO2-doped Ni/clinoptilolite nanocatalyst used in polluted air treatment

In this research nanocatalysts containing 5, 10 and 15 wt.% of Ni, dispersed by sonication over CeO₂–clinoptilolite composite support were compared toward total oxidation of toluene. Their catalytic performance at different temperatures between 150 and 350 °C was studied based on the oxidative destruction of toluene. The results indicated that the activity of Ni/CeO₂–clinoptilolite nanocatalyst for toluene oxidation increased from 33 to 44% at 250 °C by employing sonochemical method in synthesis of catalyst. Meanwhile, the catalytic activity was also improved when Ni content was increased from 5 to 10 and 15 wt.%. With the aid of several characterization techniques like XRD, FESEM, PSD, EDX, BET and FTIR, the correlation between nanocatalyst structure and its activity was addressed. It is indicated that sonochemical method can lift the catalytic activity due to the better dispersion of catalyst active components and also higher surface area. Among sonicated samples, 15 wt.% Ni nanocatalyst showed the highest toluene oxidation due to the better dispersion of catalyst active components and hence to more effective catalytic sites.     

Fatal and serious injuries related to vulnerable road users in Canada

IntroductionThe goals of this study were to analyze possible trends of fatal and serious injuries related to vulnerable road users in Canada (pedestrians, cyclists and motorcyclists) from 1990 to 2012 and the role of alcohol and drugs in these cases. Drugs have rarely been documented with respect to vulnerable road users.MethodThe Traffic Injury Research Foundation's National Fatality and Serious Injury Databases and the Public Health Agency of Canada's Canadian Hospitals Injury Reporting and Prevention Program databases were used. Numbers and rates of fatalities and serious injuries among vulnerable road users were analyzed and regression models were used to assess changes over time.ResultsThe analyses show that while the absolute number of fatalities and the rate per 100,000 population among vulnerable road users may be decreasing, no such trends are apparent when looking at the proportions of these road user fatalities out of all motor-vehicle fatalities. The trend for the proportion of motorcyclist fatalities is significantly increasing (coef. = 0.16, p < 0.001). The elderly (76 years or older) are overrepresented among pedestrian fatalities, and serious injuries (they represent 18.5% of all pedestrian fatalities but only 5.8% of the population), while those 15 years or younger are overrepresented among cyclists (they represent 23.3% of cyclist fatalities but 19.5% of the population), and those 16 to 25 years old are overrepresented among motorcyclists (27.2% of motorcyclists fatalities and 13.6% of population). Alcohol and drug use among fatally injured vulnerable road users were significant problems, especially among pedestrians. Among fatally injured pedestrians tested for alcohol and drugs, 39.7% and 43.4% tested positive, respectively.ConclusionsWith the promotion of walking and cycling as forms of exercise and the popularity of motorcycling, the safety of vulnerable road users is an important issue. The results corroborate previous research and extend our understanding about the influence of alcohol and drugs in vulnerable road user injuries.Practical applicationsThese findings can help better inform prevention and mitigation initiatives for vulnerable road users.