Adsorption of SO2 and NO from incineration flue gas onto activated carbon fibers

Activated carbon fibers (ACFs) were used to remove SO(2) and NO from incineration flue gas. Three types of ACFs in their origin state and after pretreatment with HNO(3), NaOH, and KOH were investigated. The removal efficiencies of SO(2) and NO were determined experimentally at defined SO(2) and NO concentrations and at temperatures of 150, 200 and 260 degrees C. Experimental results indicated that the removal efficiencies of SO(2) and NO using the original ACFs were <56% and <27%, respectively. All ACFs modified with HNO(3), NaOH, and KOH solution could increase the removal efficiencies of SO(2) and NO. The mesopore volumes and functional groups of ACFs are important in determining the removal of SO(2) and NO. When the mesopore volumes of the ACFs are insufficient for removing SO(2) and NO, the functional groups on the ACFs are not important in determining the removal of SO(2) and NO. On the contrary, the effects of the functional groups on the removal of SO(2) and NO are more important than the mesopore volumes as the amount of mesopores on the ACFs is sufficient to remove SO(2) and NO. Moreover, the removal efficiencies of SO(2) and NO were greatest at 200 degrees C. When the inlet concentration of SO(2) increased to 600ppm, the removal efficiency of SO(2) increased slightly and the removal efficiency of NO decreased.     

Carbonization of waste PVC to develop porous carbon material without further activation

Efficient removal of chlorine from PVC achieved by two-stage heat-treatment (280 and 410 degrees C) provided chlorine-free isotropic pitch containing additive. The pitch was stabilized and carbonized into porous carbons with surface areas of approximately 300 m2/g. Resultant porous carbons showed three pore structures of supermicropore, micropore and mesopore. The generation of CO2 from the decomposition of the CaCO3 additive in waste PVC is responsible for the development of porous structures. The surface area of the carbonized product increased after the removal of CaO.     

Paper fibers as a carbon source for the de novo formation of polychlorinated dioxins and furans

The formation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs) from carbon that was produced by the pyrolysis of paper fibers and from wood charcoal was investigated experimentally. Fibers obtained from filter paper were pyrolyzed at 300° and 800°C to produce low- and high-temperature carbon samples. The two types of carbon and wood charcoal were mixed with silica (SiO₂) and trace copper oxide to produce three synthetic fly ash samples. Experiments to measure the formation of PCCDs/Fs from the three ash samples were conducted using a bench-scale reactor. The two carbon samples derived from paper fibers generated more PCDDs/Fs than was generated by the wood charcoal. The PCDDs/Fs generated by the low-temperature carbon and by the wood charcoal were dominated by the lower-chlorinated PCDFs. Such unique homologue distribution patterns are very similar to those generated by the open burning of household waste. The high-temperature carbon generated more highly chlorinated PCDDs/Fs. The effect of pyrolysis temperature on the de novo formation of PCDDs/Fs from residual carbon is discussed. Paper and paper products contained in household waste are likely to be the source of unburned carbon that contributes to high PCDD/F emissions in the open burning of household waste.     

Adsorption of Geosmin and MIB on Activated Carbon Fibers–Single and Binary Solute System

The adsorption of two taste- and odor-causing compounds, namely MIB (2-methyl isoborneol—C₁₁H₂₀O) and geosmin (C₁₂H₂₂O) on activated carbon was investigated in this study. The impact of adsorbent pore size distribution on adsorption of MIB and geosmin was evaluated through single solute and multicomponent adsorption of these compounds on three types of activated carbon fibers (ACFs) and one granular activated carbon (GAC). The ACFs (ACC-15, ACC-20, and ACC-25) with different degrees of activation had narrow pore size distributions and specific critical pore diameters whereas the GAC (F-400) had a wider pore size distribution and lesser microporosity. The effect of the presence of natural organic matter (NOM) on MIB and geosmin adsorption was also studied for both the single solute and binary systems. The Myers equation was used to evaluate the single solute isotherms as it converges to Henry’s law at low coverage and also serves as an input for predicting multicomponent adsorption. The single solute adsorption isotherms fit the Myers equation well and pore size distribution significantly influenced adsorption on the ACFs and GAC. The ideal adsorbed solute theory (IAST), which is a well-established thermodynamic model for multicomponent adsorption, was used to predict the binary adsorption of MIB and geosmin. The IAST predicted well the binary adsorption on the ACFs and GAC. Binary adsorption isotherms were also conducted in the presence of oxygen (oxic) and absence of oxygen (anoxic). There were no significant differences in the binary isotherm between the oxic and anoxic conditions, indicating that adsorption was purely through physical adsorption and no oligomerization was taking place. Binary adsorptions for the four adsorbents were also conducted in the presence of humic acid to determine the effect of NOM and to compare with IAST predictions. The presence of NOM interestingly resulted in deviation from IAST behavior in case of two adsorbents, ACC-15 and F-400.     

Porous structure of activated carbon prepared from waste newspaper

In an earlier report, we presented a method for preparing activated carbon from waste newspaper as a way to recycle used paper for a purpose other than producing raw material for paper-making. In this article, we consider the porous structure of the activated carbon that affects its adsorption properties for various substances. The specific surface area of activated carbon prepared from waste newspaper was 838 m²/g, the micropore volume was 0.368 ml/g, and the mesopore volume was 0.138 ml/g, which is about the same as commercially available activated carbon. The activated carbon prepared from waste newspaper usually has a high content of ash, which makes little contribution to the adsorption properties. In particular, as compared with reagent-activated carbon, the quantities of mesopores with a pore radius of 3–25 nm and macropores with a pore radius of 25–250 nm were 8 and 14 times larger, respectively. Activated carbon prepared from waste newspaper has a well-developed porous structure, particularly in the mesopore and macropore ranges. Received: July 12, 1999 / Accepted: March 8, 2000     

Solubility parameters for determining optimal solvents for separating PVC from PVC-coated PET fibers

Poly(vinyl chloride) (PVC) in PVC-coated poly(ethylene terephthalate) (PET) fabrics can be separated through dissolution in a suitable solvent, leaving only the PET fibers. We investigated the solubility of PVC in 30 solvents using swelling tests. The results were compared with those obtained using the Hansen, Gutmann, Swain, E _T(30), and Kamlet–Taft parameters. For this purpose, Gaussian plots of the PVC swellability versus solubility parameter were used to decide the applicability of the solubility parameter system. Only Gutmann’s electron acceptor–donor parameter (AN + DN) and the Kamlet–Taft parameters β and π* could describe the PVC-solvent system satisfactorily. Tetrahydrofuran (THF), methyl ethyl ketone (MEK), N,N-dimethylformamide (DMF), cyclohexanone, and cyclopentanone were tested for separating PVC from PET at different temperatures. THF dissolved PVC at 20 °C, while cyclohexanone and cyclopentanone did so at 40 °C. Traces of PVC remained on the PET fibers when DMF was used. Complete dissolution of PVC was not achieved at any temperature with MEK. The present work shows that solubility parameters are a helpful tool for the search for suitable solvents. It shows also that solubility parameters have to be selected carefully, since their usefulness depends strongly on the polymer properties.     

Wet oxidative regeneration of activated carbon loaded with reactive dye

Wet Oxidative Regeneration (WOR) of powdered activated carbon (PAC) and granular activated carbon (GAC) loaded with the reactive dyes, namely chemictive brilliant blue R and cibacron turquoise blue G, was studied. Attempts were made to regenerate the loaded carbons designated now as spent carbon. A slurry (10% w/v) of spent carbon in distilled water was oxidized by wet oxidation in the temperature range of 150-250 degrees C using oxygen partial pressures between 0.69-1.38 MPa in an 1 1 SS 316 autoclave. The percent regeneration was determined from a ratio, X(RC)/X(VC), corresponding to an equilibrium adsorption capacity of regenerated carbon/equilibrium adsorption capacity of virgin carbon from an initial adsorption period of 3 h. It was observed that the regeneration mainly occurred due to the oxidation of the adsorbates taking place on the surface of carbon. It was possible to regenerate the spent GAC and PAC to the extent of more than 98% (approximately X(RC)/X(VC) > 0.98) by wet oxidation. After four consecutive cycles of adsorption and regeneration using the same stocks of GAC, carbon weight loss observed at 200 degrees C was about 40%. SEM studies of the regenerated carbon showed widening of the pores and loss of structure between the adjacent pores as compared with the virgin carbon. PAC was found to be more suitable as compared with GAC for the adsorption and wet oxidative regeneration processes to treat the aqueous solution containing lower concentration of unhydrolyzed reactive dye. The suitability of wet oxidative regeneration is demonstrated at a bench scale to treat the synthetic reactive dye solution.     

Development of a simple and sensitive method for the characterization of odorous waste gas emissions by means of solid-phase microextraction (SPME) and GC-MS/olfactometry

A solid-phase microextraction (SPME) method has been developed for the extraction of odorous compounds from waste gas. The enriched compounds were characterized by gas chromatography-mass spectrometry (GC-MS) and gas chromatography followed by simultaneous flame ionization detection and olfactometry (GC-FID/O). Five different SPME fiber coatings were tested, and the carboxen/polydimethylsiloxane (CAR/PDMS) fiber showed the highest ability to extract odorous compounds from the waste gas. Furthermore, parameters such as exposure time, desorption temperature, and desorption time have been optimized. The SPME method was successfully used to characterize an odorous waste gas from a fat refinery prior to and after waste gas treatment in order to describe the treatment efficiency of the used laboratory scale plant which consisted of a bioscrubber/biofilter combination and an activated carbon adsorber. The developed method is a valuable approach to provide detailed information of waste gas composition and complements existing methods for the determination of odors. However, caution should be exercised if CAR/PDMS fibers are used for the quantification of odorous compounds in multi-component matrices like waste gas emissions since the relative affinity of each analyte was shown to differ according to the total amount of analytes present in the sample.     

Pore structure and adsorption properties of activated carbon prepared from granular molded waste paper

We have previously manufactured activated carbon using waste paper board, which was prepared by adding 8% phenol resin adhesive to torn waste newspaper and hot-pressing. In this study, the pretreatment process of the raw material was simplified; the waste paper was extruded to form granules. The activated carbon was manufactured by the carbon dioxide activation method using the granules as the raw material. The properties of the activated carbon were evaluated based on the pore structure, the iodine adsorption number, and the adsorption of toluene vapor in a sealed chamber. The activated carbon, which was manufactured at an activation temperature of 1100°C and a treatment time of 60min, exhibited a specific surface area of 1241m²/g and an iodine adsorption number of 1120mg/g. These results were similar to those obtained for two commercially available activated carbons. The extent of toluene vapor adsorption by this activated carbon was similar to that observed for the two commercial activated carbons over a period of 130min.     

Effect of carbon dioxide injection on production of wood cement composites from waste medium density fiberboard (MDF)

The possibility of recycling waste medium density fiberboard (MDF) into wood-cement composites was evaluated. Both new fibers and recycled steam exploded MDF fibers had poor compatibility with cement if no treatment was applied, due to interference of the hydration process by the water soluble components of the fiber. However, this issue was resolved when a rapid hardening process with carbon dioxide injection was adopted. It appears that the rapid carbonation allowed the board to develop considerable strength before the adverse effects of the wood extractives could take effect. After 3-5 min of carbon dioxide injection, the composites reached 22-27% of total carbonation and developed 50-70% of their final (28-day) strength. Composites containing recycled MDF fibers had slightly lower splitting tensile strength and lower tensile toughness properties than those containing new fibers especially at a high fiber/cement ratio. Composites containing recycled MDF fibers also showed lower values of water absorption. Unlike composites cured conventionally, composites cured under CO(2) injection developed higher strength and toughness with increased fiber content. Incorporation of recycled MDF fibers into wood cement composites with CO(2) injection during the production stage presents a viable option for recycling of this difficult to manage waste material.     

Processing plastics from ASR/ESR waste: separation of poly vinyl chloride (PVC) by froth flotation after microwave-assisted surface modification

The feasibility of the selective surface hydrophilization of poly vinyl chloride (PVC) using microwave treatment to facilitate the separation of PVC via froth flotation from automobile shredder residue (ASR) and electronic waste shredder residue (ESR) was evaluated. In the presence of powder-activated carbon (PAC), 60-s microwave treatment selectively enhanced the hydrophilicity of the PVC surface (i.e., the PVC contact angle decreased from 86.8° to 69.9°). The scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) results are consistent with increased hydrophilic functional groups (i.e., ether, hydroxyl, and carboxyl), amounting to significant changes in the morphology and roughness of the PVC surface after treatment. After only 60 s of microwave treatment, 20 % of the PVC was separated in virgin and ASR/ESR plastics with 33 and 29 % purity, respectively, as settled fractions by froth flotation at a 150 rpm mixing speed. The microwave treatment with the addition of PAC had a synergetic effect with the froth flotation, which brought about 100 and 90 % selective separation of PVC from the other virgin and ASR/ESR plastics, with 91 and 82 % purity. The use of the combined froth flotation and microwave treatments is an effective technology for separating PVC from hazardous waste plastics.     

Utilization of date stones for production of activated carbon using phosphoric acid

Date stone wastes have been utilized for production of activated carbon by chemical activation with phosphoric acid using a fluidized-bed reactor. The effects of the activation time, activation temperature, impregnation ratio, and particle size on the yield and the adsorptive capacity towards iodine were studied. The yield and the quality of the activated carbon prepared by using H3PO4 were compared with that prepared from date stones using the same equipment, and under similar conditions by using ZnCl2 as an oxidizing agent. The maximum value of the iodine number of the activated carbon produced using H3PO4 in this work was about 495 under the following conditions: impregnation ratio 0.4, activation time 60 min, activation temperature 800 degrees C, particle size 0.60 mm. The iodine number for the produced activated carbon was higher when phosphoric acid was used, compared to that when zinc chloride was used as impregnation reagent; however, the yield obtained when H3PO4 was used was lower than the yield when ZnCl2 was used. The iodine number increases significantly with increasing the activation temperature. By increasing the impregnation ratio at the same temperature, the iodine number decreased sharply and an oscillation is noticed for all the cases but it was clearer at 800 degrees C. The average variation of the iodine number for the whole range of particle size used in this work is +/-10%.     

Production of hydrogen by steam gasification of dehydrochlorinated poly(vinyl chloride) or activated carbon in the presence of various alkali compounds

Steam gasification of dehydrochlorinated poly(vinyl chloride) (PVC) or activated carbon was carried out in the presence of various alkali compounds at 3.0 MPa and 560°C–660°C in a batch reactor or in a semi-batch reactor with a flow of nitrogen and steam. Hydrogen and sodium carbonate were the main products, and methane and carbon dioxide were the minor products. Yields of hydrogen were high in the presence of sodium hydroxide and potassium hydroxide. The acceleration effect of the alkali compounds on the gasification reaction was as follows: KOH > NaOH > Ca(OH)₂ > Na₂CO₃. The rate of gasification increased with increasing partial steam pressure and NaOH/C molar ratio. However, the rate became saturated at a molar ratio of NaOH/C greater than 2.0.     

Tertiary recycling of PVC-containing plastic waste by copyrolysis with cattle manure

The corrosion from pyrolysis of PVC in plastic waste was reduced by copyrolysis of PVC with cattle manure. The optimization of pyrolysis conditions between PVC and cattle manure was studied via a statistical method, the Box-Behnken model. The pyrolysis reaction was operated in a tubular reactor. Heating rate, reaction temperature and the PVC:cattle manure ratio were optimized in the range of 1-5 degrees C/min, 250-450 degrees C and the ratio of 1:1-1:5, respectively. The suitable conditions which provided the highest HCl reduction efficiency were the lowest heating rate of 1 degrees C/min, the highest reaction temperature of 450 degrees C, and the PVC:cattle manure ratio of 1:5, with reliability of more than 90%. The copyrolysis of the mixture of PVC-containing plastic and cattle manure was operated at optimized conditions and the synergistic effect was studied on product yields. The presence of manure decreased the oil yield by about 17%. The distillation fractions of oil at various boiling points from both the presence and absence of manure were comparable. The BTX concentration decreased rapidly when manure was present and the chlorinated hydrocarbon was reduced by 45%. However, the octane number of the gasoline fraction was not affected by manure and was in the range of 99-100.     

Adsorption of malachite green on groundnut shell waste based powdered activated carbon

In the present technologically fast changing situation related to waste management practices, it is desirable that disposal of plant waste should be done in a scientific manner by keeping in view economic and pollution considerations. This is only possible when the plant waste has the potential to be used as raw material for some useful product. In the present study, groundnut shell, an agricultural waste, was used for the preparation of an adsorbent by chemical activation using ZnCl2 under optimized conditions and its comparative characterisation was conducted with commercially available powdered activated carbon (CPAC) for its physical, chemical and adsorption properties. The groundnut shell based powdered activated carbon (GSPAC) has a higher surface area, iodine and methylene blue number compared to CPAC. Both of the carbons were used for the removal of malachite green dye from aqueous solution and the effect of various operating variables, viz. adsorbent dose (0.1-1 g l(-1)), contact time (5-120 min) and adsorbate concentrations (100-200 mg l(-1)) on the removal of dye, has been studied. The experimental results indicate that at a dose of 0.5 g l(-1) and initial concentration of 100 mg l(-1), GSPAC showed 94.5% removal of the dye in 30 min equilibrium time, while CPAC removed 96% of the dye in 15 min. The experimental isotherm data were analyzed using the linearized forms of Freundlich, Langmuir and BET equations to determine maximum adsorptive capacities. The equilibrium data fit well to the Freundlich isotherm, although the BET isotherm also showed higher correlation for both of the carbons. The results of comparative adsorption capacity of both carbons indicate that groundnut shell can be used as a low-cost alternative to commercial powdered activated carbon in aqueous solution for dye removal.     

Surface ozonation of polyvinyl chloride for its separation from waste plastic mixture by froth floatation

Selective surface modification of polyvinyl chloride (PVC) by ozonation was evaluated to facilitate the separation of PVC from other heavy plastics with almost the same density as PVC, especially polyethylene terephthalate (PET), by the froth flotation process. The optimum froth flotation conditions were investigated, and it was found that at 40°C, 90% of PVC and PET plastics floated. The bubble size became larger and the area covered with bubbles on the plastic surface was reduced with increasing temperature. Optimum PVC separation was achieved with the flotation solution at 40°C and mixing at 180–200 rpm, even for sheet samples 10 mm in size. Combined treatment by ozonation and froth flotation is a simple, effective, and inexpensive method for PVC separation from waste plastics.     

Physical and chemical properties study of the activated carbon made from sewage sludge

Preparation of activated carbon from sewage sludge is a promising way to produce a useful adsorbent for pollutants removal as well as to dispose of sewage sludge. The objective of this study was to investigate the physical and chemical properties of the activated carbon made from sewage sludge so as to give a basic understanding of its structure. The activated carbon was prepared by activating anaerobically digested sewage sludge with 5 M ZnCl2 and thereafter pyrolyzing it at 500 degrees C for 2 h under nitrogen atmosphere. The properties investigated in the present study included its surface area and pore size distribution, its elemental composition and ash content, its surface chemistry structure and its surface physical morphology. Furthermore, its adsorption capacities for aqueous phenol and carbontetrachloride were examined. The results indicated that the activated carbon made from sewage sludge had remarkable micropore and mesopore surface areas and notable adsorption capacities for phenol and carbon-tetrachloride. In comparison with commercial activated carbons, it displayed distinctive physical and chemical properties.     

Upgrading of poly(vinyl chloride) by chemical modifications using sodium sulfide

The recycling of poly(vinyl chloride) (PVC) is one of the most important issues in the treatment of waste plastics. To improve PVC recycling, it is necessary to develop new recycling techniques, including new techniques for the dechlorination of chlorine-containing polymers. It has been established that wet dechlorination of PVC in NaOH/ethylene glycol solution is more effective than dry dechlorination. In this study, the wet process was used, and the chemical modification of PVC by nucleophilic substitution was considered for upgrading waste PVC. Chlorine was substituted in solution by several nucleophilic reagents, thus changing the properties of PVC. The reaction of PVC in Na2S/ethylene glycol solution at 170°C resulted in the formation of a mixture comprising 32% elimination and 26% substitution products. The scanning electron microscopy/energy dispersive X-ray spectroscopy mappings and elementary analysis of PVC indicated that this chlorine-substitution process led to cross-linking by sulfur.     

Hydro-erosive separation of plastic fibers from textile compounds

There are no known methods which will effectively separate compounds consisting of plastic fibers and latex binders, or plastics coated with textiles. To separate the fibers and the plastic carrier from the other materials, high-pressure water jets have been used. Based on this practice, a method was developed to treat waste carpets and automotive interior materials with water jets in order to recycle their plastic components. Experiments were performed to investigate the modes of destruction as well as the influence of process parameters. Based on these investigations, a pilot device for the treatment of waste carpets (sheets or chips) was designed and installed. It was shown that the proposed method works with a high degree of cleanliness and selectivity. A general process scheme was developed in order to apply the method to recycling processes.     

Waste management activities and carbon emissions in Africa

This paper summarizes research into waste management activities and carbon emissions from territories in sub-Saharan Africa with the main objective of quantifying emission reductions (ERs) that can be gained through viable improvements to waste management in Africa. It demonstrates that data on waste and carbon emissions is poor and generally inadequate for prediction models. The paper shows that the amount of waste produced and its composition are linked to national Gross Domestic Product (GDP). Waste production per person is around half that in developed countries with a mean around 230 kg/hd/yr. Sub-Saharan territories produce waste with a biogenic carbon content of around 56% (+/−25%), which is approximately 40% greater than developed countries. This waste is disposed in uncontrolled dumps that produce large amounts of methane gas. Greenhouse gas (GHG) emissions from waste will rise with increasing urbanization and can only be controlled through funding mechanisms from developed countries.