Test of diesel exhaust emissions in the rat liver foci assay

In the initiation/promotion assay in rat liver, partial hepatectomy is used to enhance initiation, and a choline-devoid diet as promoter. The induction of carcinogenesis is determined by the focal appearance of gamma glutamyl transpeptidase (GGT) positive hepatocytes. We adopted this assay to diesel exhaust emission by performing a partial hepatectomy, and exposing the rats to either clean air or diesel exhaust emission. The rats were fed either a choline-devoid or a choline-supplemented diet for three or six months. The animals were sacrificed and liver sections stained for GGT were examined for the presence of foci of GGT(+) hepatocytes. The results indicate that diesel exhaust exposure does not result in a systemic dose of carcinogens sufficient to be detected in the liver foci assay.     

Control of salt laden particulate emissions from hogged fuel boilers

This paper presents the results of an evaluation of excessive salt emissions from 16 hogged fuel boilers in Washington, Oregon, and Alaska. Logs transported or stored in sea water, absorb substantial amounts of salt which is noncombustible, and is emitted as a fine particulate when the hogged fuel is burned, contributing to opacity and particulate emissions. Control measures considered are fuel pretreatment, combustion modification, use of conventional particulate control devices (electrostatic precipitators, fabric filters, and wet scrubbers), and several novel particulate control devices.The best available control technology appears to be a mechanical collector-fabric filter combination; some electrostatic scrubber type devices have also shown excellent capability.     

Facilities for diesel exhaust studies

It is the major intent of this report to examine the animal inhalation facilities at the EPA Health Effects Research Laboratory in Cincinnati, Ohio, associated with the exposure to the exhaust of diesel-powered equipment. The facility serves as a center for toxicologic evaluation, in relevant animal models, of potentially hazardous environmental pollutants from diesel engine exhaust. Briefly, the entire engine exhaust is mixed with filtered and conditioned air in a dilution tube. That diluted exhaust enters a large volume mixing chamber and a portion passes through dynamic flow irradiation chambers (to simulate sunlight) and is then conducted to animal exposure chambers. The system provides nonirradiated exhaust in the same concentration (directly from the mixing chamber) and also filtered, conditioned ambient air for control animal exposure. The major physical components of the diesel emission system include: air purifiers, animal exposure chambers, engine-dynamometers, irradiation chambers, monitoring instrumentation and data acquisition systems.     

DNA-binding studies with diesel exhaust particle extract

This study examines whether chemical components from diesel exhaust particulates react with DNA to form covalently bound adducts. Experiments in this report describe the in vitro reaction of purified DNA with a dichloromethane extract of diesel exhaust particulates in the absence or presence of enzyme activation by rat liver microsomes. The reactivity of the particle extract was compared to that of benzo[a]pyrene metabolites using low temperature fluorescence techniques which detect small quantities of polycyclic aromatic compounds bound to DNA. Incubation of DNA with the particle extract in the presence of microsomal enzymes produced no detectable fluorescent adducts in contrast to model experiments using benzo[a]pyrene. However, addition of the particle extract to incubation mixtures containing benzo[a]pyrene markedly decreased formation of benzo[a]pyrene-DNA adducts because the particle extract inhibits microsomal enzymes which activate benzo[a]pyrene and other polycyclic aromatic hydrocarbons. In the absence of microsomal enzymes, fluorescent material was detected in DNA exposed to high concentrations of the particle extract, but probably not as a result of covalent binding because the mutagenic activity of the particle extract remained unchanged during prolonged incubation with DNA. This stability is in contrast to the rapid decrease in mutagenic activity of benzo[a]pyrene-4,5-oxide during incubation with DNA. Thus, direct mutation of bacteria by the particle extract may require activation by bacterial enzymes as is known to occur with nitroaromatic compounds.     

Behavioral alterations due to diesel exhaust exposure

Several experiments examining the effects of diesel exhaust on the behavior of rats are reported. Animals were exposed either as adults or neonates. The spontaneous locomotor activity (SLA), measured in standard running wheel cages, of adult rats exposed for 8 h/day, 7 days/week was significantly less than that of controls. Experiments involving diesel exhaust exposure to neonatal rats indicated that adult rats, exposed to diesel exhaust during their neonatal lives, were significantly less active as measured by SLA. Adult rats, exposed to 20 h diesel per day as neonates, were placed in skinner boxes after the SLA experiment described above had been completed. The exhaust exposed animals showed significantly decreased acquisition of a food reinforced bar pressing task. All animals that learned this task extinguished at the same rate. The results of the neonatal diesel exhaust experiments support the hypothesis that diesel exhaust exposure during development of an organism can lead to behavioral differences in adulthood.     

Preparation and characterization of diesel exhaust particles for biological experiments

Bioassays of diesel engine exhaust components are being conducted at IITRI to determine toxic and carcinogenic potentials of the exhaust. The bioassay method, intracheal instillation of saline suspensions of test materials in hamsters, requires preparation of stable suspensions of test materials. A method to prepare suspensions of whole particle diesel exhaust in saline has been developed. The diesel exhaust particle material was supplied to IITRI as a dry, loose powder by the U.S. EPA from a light duty diesel test engine. Preliminary characterizations of the powders indicated aggregation of exhaust particles had occurred both before and during capture on collection substrates. Flake-like sheets and hollow spheres of aggregated particles up to 150 μm in sie present in the powders. Therefore, the powder were ball-milled to geometric particle sizes more amenable to the animal administration technique to be employed. Grinding, suspension preparation and particle concentration assaying methods have been developed. Particle (geometric) size and morphological characterizations have also been performed on the as-received powders and prepared suspensions. A method to prepare emulsions (liquid-liquid suspensions) of the dichloromethane extracts of whole particle diesel exhaust has also been developed.     

Time and cost characterisation of emissions from non-road diesel equipment for infrastructure projects

The construction process contributes to pollutant emissions, particularly through the operation of diesel- and gasoline-powered equipment. In the past decade, a series of investigations were undertaken to quantify these emissions for a variety of non-road construction equipment performing different activities and undergoing different duty cycles, and a model to estimate quantities of six types of pollutant was developed. This paper uses that model to estimate emissions for four street and utility construction projects which no one has done previously. We combined information from company records with standard construction industry manuals to estimate total emissions for the projects and to examine the pollution patterns and magnitudes. The street construction projects all had similar emission profiles with a large peak at the beginning and a steady output of emissions throughout the duration of the project. For example, in two of the projects studied, half of all CO₂ emissions were produced before the projects were 40% completed. Results showed that demolition and earthwork are the activities with the largest contribution. The equipment types with the largest contribution are backhoes, front-end loaders, bulldozers and trenchers. Trenchers, for example, produced 30% of all emissions on the projects on which they were used.     

Evaluation of vehicular emissions reduction strategies using a novel hybrid method integrating BWM,Q methodology and ER approach

Environment, Development and Sustainability - Road transportation is the main source of greenhouse gas (GHG) emissions in Iran. Different road transport emissions reduction strategies (RTERS) can...     

Status of connecticut's control program for transportation-related particulate emissions

Material prepared for Connecticut's 1979 State Implementation Plan (SIP) submittal indicates that transportation related sources contribute more than half of total suspended particulates (TSP) emissions. The SIP's conclusions are strikingly different from earlier estimates of TSP attributable to the transportation sector. The conclusions mandate additional measurements and analyses to document source contributions. Of greater importance is the development of TSP control measures because Connecticut's ability to maintain an adequate transportation system and to accommodate stationary source, commercial and industrial growth are affected. Possible control measures must consider control of exhaust emissions, a source control program, and control of reentrained road dust having characteristics of a fugitive emissions control program. Current programs are discussed and analyzed where sufficient data exists. Technical methodology and administrative responsibilities are discussed. Insights of future program needs are presented.     

Particle size measurements of automotive diesel emissions

The automative diesel engine has long been acknowledged as being “dirtier” than the spark ignition engine and its particulate emissions may be carcinogenic. Possible solutions to the diesel emission problem are combustion modification or aftertreatment devices. Selection of candidate aftertreatment devices requires knowledge of the physical and chemical properties of the particles, including particle morphology, size distribution, mass concentration and emission rates in the exhaust gas stream. The study reported here represents the first of a series of experiments designed to characterize the exhaust emissions and test various aftertreatment devices. This paper deals only with the particulate characterization phase of the program. Results of size distribution, particle concentration and mass emission rate measurements for a 5.71 displacement Oldsmobile diesel engine are given for a variety of engine operating conditions.     

Physical characterization of diesel exhaust particles in exposure chambers

Since the deposition of particulate in the respiratory system is strongly influenced by particle size, a correct assessment of this parameter is important for any inhalation experiment studying the potential health effects of air pollutants. Measuring the distribution of particles according to their aerodynamic diameter and mechanical mobility diameter is crucial in analyzing the deposition of submicron particles in the lower respiratory system. Cascade impactor measurements of diluted diesel exhaust in 12.6 m³ animal exposure chambers in the GMR Biomedical Science Department showed that the mass median aerodynamic diameter of the aerosol was 0.2 μm with 88% of the mass in particles smaller than 1 μm. Diffusion battery measurements showed that the mass median mechanical mobility diameter was about 0.11 μm. Transmission electron micrographs of particles deposited on chamber surfaces revealed both agglomerates and nearly spherical particles. The particles in these chambers are similar in size and shape to diesel particles described elsewhere. The flux of diesel particles to food surfaces was measured. Calculations of the expected daily dose by inhalation and by feeding showed that the “worst case” dose by feeding was only about one-tenth the dose by breathing.     

Electron paramagnetic resonance spectrometry of diesel particulate matter

Electron paramagnetic resonance (EPR) spectrometry has been used to study diesel particulate matter. The EPR signals for a graphitized carbon black and particles collected from two different diesel engines have been compared. Variations in the line widths and signal intensities due to various chemical and physical pretreatments of the particles were observed. The EPR signals for the diesel particulates were shown to be sensitive to oxygen, nitric oxide, nitrogen dioxide, and ultraviolet and visible radiation. These results suggest that EPR may be a convenient means for characterizing particles from different sources or for demonstrating particle reactivities. The demonstrated photochemical reactivities of the airborne particles have significant environmental health implications.     

Modeling and source apportionment of diesel particulate matter

The fine and ultra fine sizes of diesel particulate matter (DPM) are of greatest health concern. The composition of these primary and secondary fine and ultra fine particles is principally elemental carbon (EC) with adsorbed organic compounds, sulfate, nitrate, ammonia, metals, and other trace elements. The purpose of this study was to use an advanced air quality modeling technique to predict and analyze the emissions and the primary and secondary aerosols concentrations that come from diesel-fueled sources (DFS). The National Emissions Inventory for 1999 and a severe southeast ozone episode that occurred between August and September 1999 were used as reference. Five urban areas and one rural area in the Southeastern US were selected to compare the main results. For urban emissions, results showed that DFS contributed (77.9%+/-8.0) of EC, (16.8%+/-8.2) of organic aerosols, (14.3%+/-6.2) of nitrate, and (8.3%+/-6.6) of sulfate during the selected episodes. For the rural site, these contributions were lower. The highest DFS contribution on EC emissions was allocated in Memphis, due mainly to diesel non-road sources (60.9%). For ambient concentrations, DFS contributed (69.5%+/-6.5) of EC and (10.8%+/-2.4) of primary anthropogenic organic aerosols, where the highest DFS contributions on EC were allocated in Nashville and Memphis on that episode. The DFS contributed (8.3%+/-1.2) of the total ambient PM(2.5) at the analyzed sites. The maximum primary DPM concentration occurred in Atlanta (1.44 microg/m(3)), which was 3.8 times higher than that from the rural site. Non-linearity issues were encountered and recommendations were made for further research. The results indicated significant geographic variability in the EC contribution from DFS, and the main DPM sources in the Southeastern U.S. were the non-road DFS. The results of this work will be helpful in addressing policy issues targeted at designing control strategies on DFS in the Southeastern U.S.     

The effect of diesel exhaust on sperm-shape abnormalities in mice

The sperm-shape abnormality bioassay in mice was used to determine whether chemical mutagens in diesel exhaust reach the testes. Strain A male mice (30 per group from 4 to 6 weeks of age) were exposed for 31 or 39 weeks to either diesel exhaust or clean air. After exposure, Eosin Y-stained, air-dried smears of cauda epididymal sperm were scored for changes in sperm-head abnormalities in three different laboratories. There was no difference in the proportion of abnormally shaped sperm in controls and mice exposed to diesel exhaust.     

Carcinogenicity of diesel exhaust as tested in strain a mice

Groups of strain A mice were exposed to diesel exhaust by inhalation and diesel particulate by intraperitoneal injection. The animals were exposed from seven to eight weeks and then sacrificed 26–30 weeks postexposure. Other animals were exposed for up to seven months by the inhalation route. Some animals were promoted using urethane at a dose below which tumors would occur. There was no increase in incidence of pulmonary adenomas in the animals exposed to either diesel exhaust or diesel particulate over the control animals. In the animals which were promoted using urethane at a low dose, there was a significant increase in pulmonary adenomas. Diesel particulate was found in the lungs and bronchial lymph nodes of animals exposed to diesel exhaust 26–30 weeks after cessation of exposure.     

Development of a sampling train for the assessment of particulate fugitive emissions

A prototype portable Fugitive Assessment Sampling Train (FAST), designed to obtain large samples of particulate emissions generated by sources whose configurations preclude sample collection before the diffusion of the emissions into the ambient atmosphere, has been successfully fabricated and tested. The prototype FAST utilizes a combination of commercially available and specially designed equipment to collect a 500 milligram particulate sample in an 8-hour period at locations downwind of most industrial fugitive sources. The particulate sample is separated into inhalable and respirable fractions and provides sufficient material for a complete Level 1 assessment including bioassays. A quantity of organic species larger than C₆, sufficient for mass spectrometry analysis, is collected on a bed of adsorbent resin. The establishment of design criteria and operating parameters, selection and design of hardware components, and the fabrication and initial testing of the FAST are discussed. The results of calibration tests and an initial field trial are presented and a plan for additional development is outlined.     

Pulmonary function testing of animals chronically exposed to diluted diesel exhaust for 267 days

Thw purpose of this work was to assess the potential effect that chronic inhalation of diesel exhaust may have on lung mechanics and lung volumes. Noninvasive pulmonary function tests have been conducted repeatedly on 25 rats exposed to diesel exhaust at a particulate concentration of 1500 μg/m³, for 20 h/day, days/week for 267 days. The same tests were conducted on 25 clean air control animals. When the data is normalized, there are no apparent functionally significant changes occurring in the lungs that may be attributed to the chronic inhalation of diesel exhaust.     

Enhanced susceptibility to infection in mice after exposure to dilute exhaust from light duty diesel engines

A series of experiments was conducted in which groups of mice were first exposed for various durations to diluted exhaust from light duty diesel engines and then briefly to an infectious aerosol generated by nebulizing cultures of a bacterial pathogen (Streptococcus). Typically, postinfection mortality was significantly greater in groups exposed to exhaust than in their corresponding control groups exposed to purified air only. Data of recent diesel and of past diesel- and catalyst-treated gasoline engine exhaust experiments suggest a somewhat greater excess mortality from (enhanced susceptibility to) bacterial infection in mice exposed to diesel exhaust than in those exposed to catalytic gasoline exhaust. Limited data on acute tests of NO₂ and acrolein vapor alone suggest that the infectivity-enhancing effect of diesel exhaust could be accounted for in large part by these components. Exposures to diesel exhaust, NO₂, or acrolein did not enhance the mortality response to a viral pathogen (A/PR8-34).     

Salmonella/microsome mutagenicity assays of exhaust from diesel and gasoline powered motor vehicles

Motor vehicle exhaust from prechamber injection diesel and gasoline powered passenger cars, sampled during US FTP 1973 test cycles and comprising both particulate matter and compounds condensable at ambient temperature, has been assayed for mutagenicity in the Salmonella/microsome test. Mutagenic components were to a large extent active in the absence of the mammalian microsomal preparation. The mutagenicity of both particulate matter and condensate from diesel exhaust and condensate from gasoline exhaust was decreased in the presence of the microsomal preparation whereas the mutagenicity of particulate matter from gasoline exhaust was enhanced by microsomal activation. A comparison between the investigated diesel and gasoline exhaust samples shows that the mutagenic effect in the Salmonella test of the diesel exhaust is more than ten times higher than that of the gasoline exhaust. Fractionation with respect to polarity indicates that the mutagenic components mainly are distributed in neutral aliphatic, aromatic, and oxygenated fractions. Tests for mutagenic monofunctional nitroarenes by an anaerobic assay indicate that such compounds at most are marginally present in the exhaust samples as compared with their presence in airborne particulate matter collected in an urban environment.     

A study of diesel emissions on Drosophila

A sex-linked recessive lethal test was performed on male fruit flies of the species Drosophila melanogaster, (Oregon-R strain), exposed to an approximate five-fold dilution of exhaust from a diesel engine. The eight hour exposure was achieved by drawing diluted diesel exhaust from a three cubic meter stainless steel exposure chamber housing laboratory animals through a two liter reaction flask modified for use with Drosophila. A preconditioned sampling bag was used to collect the emissions after passing through the exposure chamber containing the flies. Results of analyses performed on the diesel exhaust mixture showed the following: carbon dioxide—0.17%, carbon monoxide—12.2 ppm, hydrocarbons—11.6 ppm, nitrogen oxide—3.8 ppm, nitrogen dioxide—2.9 ppm, sulphur dioxide—1.0 ppm, and particulates—2.18 mg/m³. Two broods of the F₂ generation were investigated for the occurrence of recessive lethal events. These broods approximated the developing gametogenic stages of mature sperm (P₁ matings on days 2 and 3 postexposure) and spermatocytes (P₁ matings on days 8 and 9). Additionally, the F₃ generation was evaluated for the occurrence of mosaic recessive lethal events which might escape detection in the F₂ generation. An equal number of F₂ and F₃ flies for both broods served as concurrent controls. Results indicate that, under the conditions tested, the diesel exhaust did not increase the mutation frequency of the exposed flies (F₂ rate = 0.30%, F₃ rate = 0%) when compared to the concurrent controls (F₂ rate = 0.37%, F₃ rate = 0.15%).