Collaborative evaluation of the analytical state-of-the-art of platinum, palladium and rhodium determinations in road dust

In order to control the quality of platinum, palladium and rhodium determinations in road dust, the Standards, Measurements and Testing Programme (formerly BCR) of the European Commission has started a project, the final aim of which is to certify a road dust reference material for its contents of platinum group elements. The first part of this project consisted of an interlaboratory study, which aimed to test the feasibility of the preparation of a candidate road dust reference material and to detect and remove most of the pitfalls observed in platinum, palladium and rhodium determinations. This paper presents the main results of this interlaboratory study carried out prior to the certification campaign. The concordance of the data obtained by the participating laboratories for the three elements was considered to reflect the state-of-the-art and was encouraging enough to decide on the organization of a certification campaign to be conducted during the year 2000. The progress made with respect to the analytical state-of-the-art for these elements will be of great benefit to the quality of measurements carried out in environmental monitoring in this particular field.     

Evaluation of the state-of-the-art of butyl- and phenyltin compound determinations in freshwater sediment prior to certification of a reference material

In order to control the quality of butyl- and phenyltin compound determinations in sediment, the Standards, Measurements and Testing Programme (formerly BCR) of the European Commission has started a project, the final aim of which is to certify a freshwater sediment for its contents of a range of organotin compounds (mono-, di- and tributyltin, and mono-, di- and triphenyltin). The first part of this project involved an interlaboratory study which aimed to test the feasibility of preparation of candidate freshwater sediment reference material and to detect and remove most of the pitfalls observed in organotin determinations. This paper presents the main results of this interlaboratory study carried out prior to the certification campaign. The agreement obtained among laboratories for the six compounds determined was considered to reflect the state-of-the-art and was encouraging enough to decide upon the organisation of a certification campaign, which will be concluded in June 1999.     

Evaluation of performance of time-saving extraction devices in the BCR three-step sequential extraction procedure

Two alternative extraction methods--a routine ultrasonic bath and a microwave oven--were developed and optimized for their eventual exploitation in the three-stage sequential extraction procedure proposed by the European Standards, Measurements and Testing (S, M & T) Programme, formerly Bureau Communitaire de Reference (BCR), for the operationally defined speciation of Cd, Cr, Cu, Ni and Zn. The conventional BCR three-stage sequential extraction procedure was modified at each stage, applying ultrasonic or microwave devices in order to shorten the required 16 h of shaking in all three steps. The experimental tests and the optimization of the operating parameters were carried out on a highly homogenized estuarine sediment reference material (RM S7) prepared by the Joint Research Centre (JRC) of ISPRA. Extractable metal contents were measured by inductively coupled plasma-mass spectrometry (ICP-MS) and the results obtained in each fraction by all three methods were statistically compared for all the studied elements. The conventional and newly developed alternative extraction methods were finally compared by the analysis of BCR 601, which is certified for the three-step BCR sequential extraction procedure. According to the statistical evaluation of the results, the proposed accelerated sequential extraction methods are valid alternatives to conventional shaking, with much shorter extraction times.     

微波消解电感耦合等离子体质谱法测定土壤中稀土金属元素

建立了一种电感耦合等离子体质谱测定土壤中微量稀土金属的方法.分析了土壤标准样品中的微量稀土元素,结果与标准值一致.土壤实际样品分析也得到可靠结果.该方法样品采用微波溶样,灵敏度高,是一种比较可靠的微量稀土元素分析新方法.     

A new organic-rich soil reference material certified for its EDTA- and acetic acid- extractable contents of Cd, Cr, Cu, Ni, Pb and Zn, following collaboratively tested and harmonised procedures

There is an increasing requirement for assessment of the bioavailable metal fraction and the mobility of trace elements in soils upon disposal. One of the approaches is the use of leaching procedures, but the results obtained are operationally defined; therefore, their significance is highly dependent on the extraction protocol performed. So, for this type of study, there is a need for reference materials that allow the quality of measurements to be controlled. This paper describes the steps involved in the certification of an organic-rich soil reference material, BCR-700, for the EDTA- and acetic acid-extractable contents of some trace elements, following collaboratively tested and harmonised extraction procedures. Details are given for the preparation of the soil, homogeneity and stability testing, analytical procedures and the statistical selection of data to be included in the certification.     

Comparison of different multielement techniques for analysis of mosses used as biomonitors

Mosses are used as biomonitors on a regular basis to study trends in the atmospheric deposition of trace elements in Norway. In this paper the analytical scheme used so far, based on a combination of instrumental neutron activation analysis and atomic absorption spectrometry (INAA/AAS) is compared with inductively coupled plasma emission spectrometry (ICP-ES) and inductively coupled plasma mass spectrometry (ICP-MS). ICP-ES provided satisfactory data for nearly 20 elements, but detection limits were inadequate for some elements of importance. For ICP-MS quantitative data were obtained for 33 elements including the heavy metals of key interest in air pollution studies. In most cases where comparison was possible the ICP-MS data compared favourably with data obtained by the reference scheme or by ICP-ES. On the basis of this study ICP-MS is considered to be an equivalent alternative to INAA/AAS in multielement studies using mosses as biomonitors. In addition ICP-MS offers some promise for the study of elements such as Be, Ga, Mo, Te, Tl, and Bi, for which very little information exists regarding their behaviour as air pollutants.     

Feasibility study prior to the certification of trace elements in urban and industrial wastewater reference materials

Reliable results for the determination of trace elements in urban and industrial wastewaters are of paramount importance for both checking the performance of sewage treatment and for detecting possible urban or industrial contamination sources. The quality control of measurements should in principle rely on external tools such as certified reference materials (CRM), which should represent, as closely as possible, the matrix of samples currently analysed, e.g., in the frame of environmental monitoring. To date, however, no CRM representatives of wastewater composition are available, which limits the possibility for control laboratories to check their QC externally. To fill this gap, the European Commission's Standards, Measurements and Testing Programme (formerly BCR) has started a European collaborative project of which the aim is to test the feasibility of preparation of wastewater reference materials and the analytical state-of-the-art to enable the certification of trace elements in such matrices. This paper presents the results of the first phase of this project, namely the feasibility study and the results of an interlaboratory trial.     

Major and trace element contents in apples from a cultivated area of central Greece

Forty-two soil and apple samples from central Greece were collected and analyzed with regards to the content in major (Ca, Fe, K, Mg, Na, P, and S) and trace elements (As, B, Ba, Cd, Co, Cr, Cu, Hg, Mn, Mo, Ni, Pb, Sb, Sc, Se, Sr, Ti, and Zn). Soil samples were analyzed by inductively coupled plasma atomic emission spectrometry, while for the apples inductively coupled plasma mass spectrometry was implemented. Several elements such as As, B, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Se, Ti, and Zn, represent high concentrations in apples from the study area. These relatively high concentrations may be a consequence of the local geology, along with the excessive application of agricultural products such as fertilizers and agrochemicals.     

Development of an ombrotrophic peat bog (low ash) reference material for the determination of elemental concentrations

Given the increasing interest in using peat bogs as archives of atmospheric metal deposition, the lack of validated sample preparation methods and suitable certified reference materials has hindered not only the quality assurance of the generated analytical data but also the interpretation and comparison of peat core metal profiles from different laboratories in the international community. Reference materials play an important role in the evaluation of the accuracy of analytical results and are essential parts of good laboratory practice. An ombrotrophic peat bog reference material has been developed by 14 laboratories from nine countries in an inter-laboratory comparison between February and October 2002. The material has been characterised for both acid-extractable and total concentrations of a range of elements, including Al, As, Ca, Cd, Cr, Cu, Fe, Hg, Mg, Mn, Na, Ni, P, Pb, Ti, V and Zn. The steps involved in the production of the reference material (i.e. collection and preparation, homogeneity and stability studies, and certification) are described in detail.     

Collaborative study to improve the quality control of rare earth element determinations in environmental matrices

In order to control the quality of rare earth determinations in environmental matrices, the Standards, Measurements and Testing Programme (formerly Community Bureau of Reference, BCR) of the European Commission has started a project, the final aim of which is to certify four types of matrices (tuna muscle, mussel tissue, aquatic plant and estuarine sediment) for their contents of a range of rare earth elements (Sc, Y and the lanthanides: La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb and Lu). The elements U and Th were added to the study. The first part of this project consisted of an interlaboratory study which aimed to test the feasibility of preparation of environmental reference materials and to detect and remove most of the pitfalls observed in rare earth determinations. This paper presents the preparation of the four matrices for the intercomparison study and for the candidate reference material. The main results are presented of the interlaboratory study that was carried out prior to the certification campaign. This collaborative trial is the first attempt ever carried out at this scale to evaluate the state-of-the-art of rare earth determinations in the environment. Its impact on the improvement of chemical measurements will have positive effects on the comparability of data necessary for environmental monitoring.     

Monitoring trace metals in urban aerosols from Buenos Aires city. Determination by plasma-based techniques

A study was undertaken, within the framework of a 3 years national project, to assess the content of 13 elements in airborne particulate matter collected in representative zones of the metropolitan area of Buenos Aires. The sampling strategy followed consisted in collecting simultaneously 67 samples of PM10 particulate matter in 9 sampling sites covering an area of about 30 km2 during one week. The collection was performed on ash-free fibre-glass filters using high volume samplers. A combination of aqua regia and perchloric acid was used for leaching metals from filters. Key elements, namely Al, Ca, Cu, Fe, Mn, Mo, Ni, Pb, S, Sb, Sn, Zn and Zr, were determined by inductively coupled plasma-optical emission spectrometry (ICP-OES) and inductively coupled plasma-mass spectrometry (ICP-MS) at micro g g(-1) and ng g(-1) levels. Analyte concentration varied from 130 ng g(-1)(Mo) to over 30%(Ca). Multivariate statistical analysis was performed on the data set including the measured elemental compositions for the monitored period. The atmospheric concentration found for Pb confirms the decreasing levels of this element since the introduction of unleaded gasoline in 1995: 88 ng m(-3)(2001) < 220 ng m(-3)(1997) < 3900 ng m(-3)(1994). The average S concentration above 3 microg m(-3) is somehow unexpectedly high for Buenos Aires since the relatively low S content of liquid fuels and the massive usage of natural gas imply low emissions of this element from combustion activities. To the best of our knowledge, S concentrations are reported for the first time for this city.     

南极大气气溶胶中铅同位素比值的研究

通过对电感耦合等离子体质谱(ICP-MS)的工作条件和参数进行优化,建立了ICP-MS测定铅同位素比值的精确方法,测量了2007—2009年南极中山站采集到的气溶胶样品中208Pb/206Pb、207Pb/206Pb和206Pb/207Pb的比值。结果表明,南极大气气溶胶中铅同位素比值在逐年缓慢地发生线性变化,线性相关系数为0.996 2;气溶胶铅同位素示踪揭示南极附近国家(除南非)释放的铅可能成为南极大气中铅的重要来源。     

Soft cost elements: Exploring management components of project costs in green building projects

This paper reveals the non-technical elements that affect construction project costs, known as soft cost elements (SCEs). These elusive elements have received little attention although they are significant in influencing management decisions of a project. There is much interest in the mitigation of cost for green projects, but the focus is generally leaning towards hard cost aspects. Information about SCEs remains obscure. Qualitative approach is adopted in this research using face-to-face unstructured interviews with 12 respondents consisting of green building project experts who have been involved in many projects certified by the Malaysia Green Building Index (GBI). A total of 4 project cost datasheets were also analysed to confirm the SCEs in the project budget and to enable a clear definition of the SCEs term. The results show that SCEs are tangible and not hidden in nature. Although they constitute smaller percentage in the project cost, the implications of SCEs are far-reaching and can influence critical management decisions. There are 8 SCEs identified which are divided into 3 main categories: 1) Design Influence (project brief preparation, consultant fees and green certification); 2) Authority Requirement (pre-development charges and contribution charges); and 3) Development Provision (marketing, project overheads and security of funding). This study is practical and relevant for both green and conventional construction project, with an additional of ‘green certification’ element for green projects. The paper provides new insight into the understated elements that drive project cost from a managerial perspective and indicates key areas for future studies on project cost.     

Trace metal concentrations of surface snow from Ingrid Christensen Coast, East Antarctica—spatial variability and possible anthropogenic contributions

To investigate the distribution and source pathways of environmentally critical trace metals in coastal Antarctica, trace elemental concentrations were analyzed in 36 surface snow samples along a coast to inland transect in the Ingrid Christensen Coast of East Antarctica. The samples were collected and analyzed using the clean protocols and an inductively coupled plasma mass spectrometer. Within the coastal ice-free and ice-covered region, marine elements (Na, Ca, Mg, K, Li, and Sr) revealed enhanced concentrations as compared with inland sites. Along with the sea-salt elements, the coastal ice-free sites were also characterized by enhanced concentrations of Al, Fe, Mn, V, Cr, and Zn. The crustal enrichment factors (Efc) confirm a dominant crustal source for Fe and Al and a significant source for Cr, V, Co, and Ba, which clearly reflects the influence of petrological characteristics of the Larsemann Hills on the trace elemental composition of surface snow. The Efc of elements revealed that Zn, Cu, Mo, Cd, As, Se, Sb, and Pb are highly enriched compared with the known natural sources, suggesting an anthropogenic origin for these elements. Evaluation of the contributions to surface snow from the different sources suggests that while contribution from natural sources is relatively significant, local contamination from the increasing research station and logistic activities within the proximity of study area cannot be ignored.     

Certification of the extractable contents of Cd, Cr, Cu, Ni, Pb and Zn in a freshwater sediment following a collaboratively tested and optimised three-step sequential extraction procedure

Sequential extraction procedures have been used during the last decades to study and determine trace element mobility in aquatic sediments. However, the results obtained are operationally defined and, therefore, the significance of the analytical results is related to the extraction scheme used. So, there is a need for suitable reference materials for this type of study to enable the validation of the methodologies and to control the quality of the measurements. This paper describes the preparation of a sediment reference material, BCR-701, the homogeneity and stability studies and the analytical work performed for the certification of the extractable contents of some trace elements, following a collaboratively tested and optimised sequential (three-step) extraction procedure. The paper contains all the results and gives the methods used to certify the extractable contents (mass fractions expressed as mg kg-1 on a dry matter basis) of Cd, Cr, Cu, Ni, Pb and Zn in all steps. Moreover, indicative values are given for the aqua regia extractable contents of the six elements in the sediment and the residue obtained after sequential extraction.     

Quality assurance in measuring the elemental composition of the alga Fucus vesiculosus

Algae are increasingly used for the purpose of environmental biomonitoring, for instance in the long-term program of the Federal Environmental Specimen Bank of Germany. Therefore, for the studies presented here, freeze-dried samples of Fucus vesiculosus collected from the North Sea shores were analyzed for a broad range of elements by instrumental neutron activation analysis (INAA), while inductively coupled plasma atomic emission spectrometry (ICP-AES) and mass spectrometry (ICP-MS) were carried out on digests. The entire analytical procedures, including field sampling, cleaning of material, sample handling, determination of blanks and instrumental parameters, are described. Certified reference materials analyzed in parallel with real samples and intermethod comparisons were used for assuring the accuracy of the analytical data. Reproducibility of INAA measurements was between 4 and 6% depending on the element considered. Possible sources of uncertainty and variation of the contaminant origins are discussed. Boundary conditions for the performance of algae sampling within environmental monitoring programs and the application of this marine bioindicator for the purpose of controlling time-dependent and local differences in element patterns are presented.     

环境样品中~(237)Np的ICP-MS分析研究进展

近年来,环境样品中237Np的准确测量受到越来越多的关注。随着质谱技术的发展,电感耦合等离子体质谱(ICP-MS)成为研究和测量环境样品中237Np的重要手段。文章从样品制备、定量方法、干扰降低、进样系统改进、与色谱联用等方面,对ICP-MS分析环境样品中237Np的研究进展作了评述。     

Determination of organophosphorus fire retardants and plasticizers in wastewater samples using MAE-SPME with GC-ICPMS and GC-TOFMS detection

Determination of organophosphorus fire retardants and plasticizers at trace levels in wastewater is described. In this work, microwave assisted extraction (MAE) and solid-phase microextraction (SPME) are used for sample preparation to extract and preconcentrate the analytes, followed by analysis by gas chromatography coupled to inductively coupled plasma mass spectrometry (GC-ICP-MS) for phosphorus-specific detection. Gas chromatography coupled to time of flight mass spectrometry (GC-TOF-MS) was used to confirm the organphosphorus fire retardants in wastewater. The detection limits of organophosphorus fire retardants (OPFRs) were 29 ng L(-1) for tri-n-butyl phosphate (TnBP), 45 ng for L(-1) for tris(2-butoxyethyl)phosphate (TBEP), and 50 ng L(-1) for tris(2-ethylhexyl)phosphate (TEHP). Optimized extraction conditions were performed at 65 degrees C for 30 min and with 10% NaCl. Application of MAE during the sample preparation prior to the SPME allowed the detection of tris(2-ethylhexyl) phosphate, which has been difficult to determine in previous work. Application of the method to wastewater samples resulted in detecting 3.1 microg L(-1) P from TnBP, 5.0 microg L(-1) P from TBEP, and 4.0 microg L(-1) P from TEHP. The presence of these compounds were also confirmed by SPME-GC-TOF-MS.     

微波消解ICP-MS法同时测定大气颗粒物中多种痕量元素

采用微波消解电感耦合等离子体质谱法同时测定大气颗粒物中13种元素,选择硝酸体系消解20 min,硝酸加入体积为8 mL。Cu、Ni、Cr、Pb、Al、Mg、Mn、Ca在0μg/L～100μg/L,Ag、Ba、Co、Cd、Sn在0μg/L～5.00μg/L范围内线性良好,除Al、Mg、Ca检出限较高外,其他10种元素的检出限为0.07 ng/m3～1.82 ng/m3(按采样体积0.688 m3、定容体积50 mL计),滤膜样品平行测定3次的RSD≤1.2%,加标回收率在92%～108%之间。     

A new mussel certified reference material (CRM 477) for the quality control of butyltin determination in the marine environment

The analytical techniques used for the determination of butyltin compounds in biological tissues are generally based on a succession of steps (e.g., extraction, derivatization, separation, detection) which are all prone to systematic errors. An interlaboratory programme performed at the EU level and based on a stepwise approach has enabled one to identify and remove most of these errors and to improve considerably the state of the art so that certification of a mussel reference material has been made possible. This paper describes the preparation of this mussel reference material containing monobutyltin (MBT), dibutyltin (DBT) and tributyltin (TBT), the homogeneity and stability studies and the analytical work performed for the certification of the contents of MBT [Sn(C4H9)3+], DBT [Sn(C4H9)2(2+)] and TBT [Sn(C4H9)3+]. The results obtained by a group of expert EU laboratories are discussed along with the methods used to certify the mass fractions (based on dry mass) of monobutyltin (1.50 +/- 0.28 mg kg-1 as MBT cations), dibutyltin (1.54 +/- 0.12 mg kg-1 as DBT cations) and tributyltin (2.20 +/- 0.19 mg kg-1 as TBT cations). The paper also describes an attempt to certify the content of triphenyltin in this material which, although reasonable agreement was found among the participants' results, failed owing to the instability of this compound. This new material will be of great support to ensure the quality control of butyltin determination in shellfish, as carried out in environmental monitoring programmes.